Motherboard P9X79
E8038 Revised Edition V2 January 2013 Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices vi Safety information...................................................................................................... vii About this guide........................................................................................................ viii P9X79 specifications summary.................................................................................. x Chapter 1: 1.1 1.2 1.3 Package contents......................................................................................
Contents 2.4 2.5 Starting up for the first time..................................................................... 2-48 Turning off the computer.......................................................................... 2-48 Chapter 3: 3.1 3.2 3.3 3.4 Knowing BIOS............................................................................................. 3-1 BIOS setup program................................................................................... 3-1 3.2.1 3.2.2 3.5.1 CPU Configuration.
4.3.1 AI Suite II..................................................................................... 4-3 4.3.3 DIGI+ Power Control.................................................................... 4-8 4.3.2 TurboV EVO................................................................................. 4-4 4.3.4 EPU............................................................................................ 4-10 4.3.5 FAN Xpert+.........................................................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Safety information Electrical safety • • • • • • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • • • • • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
P9X79 specifications summary CPU 2nd Generation Intel® Core™ i7 Processor family for the LGA 2011 Socket Supports Intel® Turbo Boost Technology 2.0 * The Intel® Turbo Boost Technology 2.0 support depends on CPU types. ** Refer to www.asus.com for Intel CPU support list Chipset Intel® X79 Express Chipset Memory 8 x DIMM, max. 64GB, DDR3 2400(O.C.) / 2133(O.C.
P9X79 specifications summary USB 2 x ASMedia® USB 3.0 controllers - 4 x USB 3.0/2.0 ports at back panel (Blue) Intel® X79 Express Chipset - 14 x USB 2.0/1.
P9X79 specifications summary ASUS exclusive overclocking features Precision Tweaker 2: - vCore: Adjustable CPU voltage at 0.005V increment - vTTCPU: Adjustable I/O voltage at 0.00625V increment - vCCSA: 255-step system agent voltage control - vDRAM Bus: 160-step Memory voltage control - vPCH: 96-step Chipset voltage control - vCPU_PLL: 48-step CPU & PCH PLL voltage control SFS (Stepless Frequency Selection): - BCLK/PEG frequency tuning from 80MHz up to 300MHz at 0.
Chapter 1 Chapter 1: Product introduction 1.1 Welcome! Thank you for buying an ASUS® P9X79 motherboard! Chapter 1 The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items.
1.3 Special features 1.3.1 Product highlights 2nd Generation Intel® Core™ i7 Processor family for the LGA 2011 Socket Chapter 1 This motherboard supports the latest 2nd Generation ����� Intel® Core™ ����������������������������� i7 Processor Family in LGA2011 package, with memory and PCI Express controllers integrated to quad-channel (8 DIMMs) DDR3 memory and 40 PCI Express 3.0 lanes. This provides great graphics performance.
1.3.2 Dual Intelligent Processors 3 with New DIGI+ Power Control Chapter 1 The world’s first Dual Intelligent Processors from ASUS pioneered twin onboard chips - TPU (TurboV Processing Unit) and EPU (Energy Processing Unit). Third generation Dual Intelligent Processors with New DIGI+ Power Control include two digital voltage regulator modules (VRMs). An all-new digital controller now allows ultra-precise DRAM tuning in addition to CPU voltage control.
1.3.3 ASUS Exclusive Features Chapter 1 USB BIOS Flashback USB BIOS Flashback offers the most convenient way to flash the BIOS ever! It allows overclockers to try new BIOS versions easily, without even entering their existing BIOS or operating system. Just plug in USB storage and push the dedicated button for 3 seconds, and the BIOS is automatically flashed using standby power. Worry-free overclocking for the ultimate convenience! USB 3.0 Boost New ASUS USB 3.
1.3.5 ASUS EZ DIY Chapter 1 ASUS UEFI BIOS ASUS UEFI BIOS offers the first mouse-controlled graphical BIOS designed with selectable modes, providing a user-friendly interface that goes beyond traditional keyboard-only controls. It also natively supports fully-utilized hard drives larger than 2.2TB in 64-bit operating systems. ASUS exclusive interface EZ Mode displays frequently-accessed info. Users can choose system performance settings and drag and drop boot priorities.
DTS UltraPC II Chapter 1 DTS UltraPC II delivers exceptional 7.1 surround through the most popular PC audio setups - your existing stereo speakers or headphones. In addition to virtual surround, it upgrades original sound to new levels with Audio Restoration, recreating the dynamic range of audio files. Symmetry mode improves the balance of perceived loudness across different input sources and Enhance boosts audio quality through high and low frequency equalization.
Chapter 2 Chapter 2: Hardware information 2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. ASUS P9X79 • Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity.
2.2 Motherboard overview 2.2.1 Motherboard layout Chapter 2 Refer to 2.2.8 Internal connectors and 2.3.11 Rear panel connection for more information about rear panel connectors and internal connectors.
Connectors/Jumpers/Slots Page 1. DDR3 DIMM slots 2-5 2. ATX power connectors (24-pin EATXPWR, 8-pin EATX12V) 2-30 3. LGA2011 CPU socket 2-4 4. CPU, CPU OPT, Chassis fan connectors (4-pin CPU_FAN, 4-pin CPU_OPT, 4-pin CHA_FAN1/2/3/4) 2-28 5. MemOK! 2-17 6. Intel® X79 Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1/2 [gray]) 2-23 7. Intel® X79 Serial ATA 3.0 Gb/s connectors (7-pin SATA3G_3–6 [blue]) 2-24 8. TPU switch 2-18 9. EPU switch 2-19 10. Standby Power LED 2-20 11.
2.2.2 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA2011 socket designed for the 2nd Generation Intel® Core™ i7 Processor Family. Chapter 2 Ensure that all power cables are unplugged before installing the CPU. 2-4 • Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.
2.2.3 System memory The motherboard comes with eight Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) slots. Chapter 2 A DDR3 module is notched differently from a DDR or DDR2 module. DO NOT install a DDR or DDR2 memory module to the DDR3 slot.
Memory configurations You may install 1GB, 2GB, 4GB, and 8GB unbuffered, and non‑ECC DDR3 DIMMs into the DIMM sockets. Chapter 2 2-6 • You may install varying memory sizes in Channel A, B, C, and D. The system maps the total size of the lower-sized channel for the dual-channel, triple-channel, or quadchannel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 2400 MHz capability Vendors Part No. Size SS/DS Chip Brand Chip NO. Timing G.SKILL F3-19200CL9D-4GBPIS(XMP) 4G ( 2x 2G ) DS - - 9-11-9-28 1.65 • • 2GB DS - - - 1.65 • • Transcend TX2400KLU-4GK(374243)(XMP) 2GB DS - - - 1.65 • Transcend TX2400KLU-4GK (381850)(XMP) Voltage DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM • P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 2250 MHz capability Part No.
P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 2133 MHz capability (continued) Vendors Part No. Size SS/DS Chip Brand Chip NO. Timing Voltage DIMM socket support (Optional) 2 DIMM 4 DIMM 6 DIMM 8 DIMM KINGSTON KHX2133C9AD3T1K2/ 4GX(XMP) 4GB ( 2x DS 2GB ) - - - 1.65 4GB ( 2x DS 2GB ) - - 9 1.65 • • KINGSTON KHX2133C9AD3W1K2/ 4GX(XMP) 4GB ( 2x DS 2GB ) - - 9 1.65 • • • • 4GB ( 2x DS 2GB ) - - 9 1.65 • • • • 4GB ( 2x DS 2GB ) - - 9-9-9-24 1.
P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 1866 MHz capability Vendors Part No. Size SS/DS Chip Brand Chip NO. Timing Voltage A-DATA AX3U1866GC2G9B(XMP) 2GB SS - - 9-11-9-27 1.55~1.75 A-DATA AX3U1866GC4G9B(XMP) 4GB DS - - 9-11-9-27 1.55~1.75 CORSAIR CMZ8GX3M2A1866C9(XMP) - - 9-10-9-27 1.5 G.SKILL F3-14900CL9Q16GBXL(XMP) 8GB ( 2x 4GB DS ) DS - - 9-10-9-28 1.5 • • F3-15000CL9D-4GBTD(XMP) 4GB(2 x 2GB) DS - - 9-9-9-24 1.
P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 1600 MHz capability (continued) Vendors Part No. Size SS/DS Chip Brand Chip NO. Timing CORSAIR CMZ8GX3M2A1600C8(XMP) 8GB ( 2x 4GB ) DS - - DS - - 9-9-9-24 1.5 DS - - 8-8-8-24 1.65 CORSAIR CMZ8GX3M2A1600C9(XMP) CORSAIR CMD8GX3M4A1600C8(XMP) 8GB ( 2x 4GB ) 8GB(4 x 2GB) • • BL12864BN1608.8FF(XMP) SS - - 8-8-8-24 1.65 • BL25664BN1608.16FF(XMP) 2GB DS - - 8-8-8-24 1.65 • F3-12800CL7Q16GBXH(XMP) 16GB ( 4x 4GB ) G.
P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 1600 MHz capability (continued) Vendors Part No. Size SS/DS Chip Brand Chip NO. Timing Voltage DIMM socket support (Optional) KINGSTON KHX1600C9D3T1BK3/ 6GX(XMP) 6GB ( 3x 2GB ) DS - - 9 1.
P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 1333 MHz capability Vendors Part No. Size SS/ DS Chip Brand Chip NO. Timing Voltage A-DATA AD63I1B0823EV 2GB SS A-DATA 3CCA-1509A - - A-DATA AD63I1C1624EV 4GB DS A-DATA 3CCA-1509A - - A-DATA A-DATA Apacer Apacer Apacer CORSAIR CORSAIR AXDU1333GC2G9(XMP) SU3U1333W8G9(XMP) 78.01GC6.9L0 78.A1GC6.9L1 78.B1GDE.
P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 1333 MHz capability (continued) Part No. Size KINGSTON KHX1333C9D3UK2/ 4GX(XMP) - KINGSTON KVR1333D3N9K2/4G 4GB ( DS 2x 2GB ) KINGSTON KVR1333D3E9S/4G 4GB MICRON MT8JTF25664AZ-1G4D1 2GB MICRON MICRON MICRON MICRON MICRON SS/DS Chip Brand Chip NO. Timing Voltage DIMM socket support (Optional) 9 1.
P9X79 Motherboard Qualified Vendors Lists (QVL) DDR3 1333 MHz capability (continued) Chapter 2 Vendors Part No. Size SS/DS Chip Brand Chip NO.
2.2.4 Expansion slots Chapter 2 Ensure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. Slot No. Slot Description 1 PCIe 3.0 x16_1 slot (single at x16 or dual at x16/x16 mode) 3 PCIe 2.0 x1_2 slot 2 4 5 6 PCIe 2.0 x1_1 slot PCIe 3.0 x16_2 slot (dual at x16/x16 mode) PCI slot 1 PCIe 3.
• • • • In single VGA card mode, use the PCIe 3.0 x16_1 slot (blue) for a PCI Express x16 graphics card to get better performance. In CrossFireX™ or SLI™ mode, use the PCIe 3.0 x16_1 and PCIe 3.0 x16_2 slots for PCI Express x16 graphics cards to get better performance. We recommend that you provide sufficient power when running CrossFireX™ or SLI™ mode. Refer to page 2-30 for details.
2.2.5 Onboard switches Onboard switches allow you to fine-tune performance when working on a bare or opencase system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. MemOK! switch Installing DIMMs that are incompatible with the motherboard may cause system boot failure, and the DRAM_LED near the MemOK! switch lights continuously.
2. TPU switch Turning this switch to Enable will automatically optimize the system for fast, yet stable clock speeds. For ensuring the system performance, turn the switch setting to Enable when the system is powered off. Chapter 2 2-18 • The TPU LED (O2LED2) near the TPU switch lights when the switch setting is turned to Enable. Refer to section 2.2.6 Onboard LEDs for the exact location of the TPU LED.
3. EPU switch Turning this switch to Enable will automatically detect the current PC loadings and intelligently moderate the power consumption. Chapter 2 For ensuring the system performance, turn the switch setting to Enable when the system is powered off. ASUS P9X79 • The EPU LED (O2LED3) near the EPU switch lights when the switch setting is turned to Enable. Refer to section 2.2.6 Onboard LEDs for the exact location of the EPU LED.
2.2.6 1. Chapter 2 2. 2-20 Onboard LEDs Standby Power LED The Standby Power LED will light up once the system is connected to a power source. Q-LEDs These ID LEDs of CPU, DRAM, VGA card, and HDD indicate key component status during POST (Power-on Self Test), providing an elegant embellishment to the motherboard design. The LED lights will flash sequentially during system bootup. If an error is found, the LED next to the error device will continue lighting until the problem is solved.
4. TPU LED The TPU LED lights when the TPU switch is turned to Enable. Chapter 2 3. EPU LED The EPU LED lights when the EPU switch is turned to Enable.
2.2.7 1. Jumper Clear RTC RAM (3-pin CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. Chapter 2 To erase the RTC RAM: 1. 2. 3. 4. Turn OFF the computer and unplug the power cord. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2.2.8 1. Internal connectors Intel Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1/2 [gray]) ® These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. Chapter 2 If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10 configuration with the Intel® Rapid Storage Technology through the onboard Intel® X79 chipset. • These connectors are set to [AHCI Mode] by default.
2. Intel® X79 Serial ATA 3.0 Gb/s connectors (7-pin SATA3G_3–6 [blue]) These connectors connect to Serial ATA 3.0 Gb/s hard disk drives and optical disc drives via Serial ATA 3.0 Gb/s signal cables. If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10 configuration with the Intel® Rapid Storage Technology through the onboard Intel® X79 chipset. Chapter 2 • These connectors are set to [AHCI Mode] by default.
USB 2.0 connectors (10-1 pin USB78; USB910; USB1112; USB1314) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed. Chapter 2 3. Never connect a 1394 cable to the USB connectors.
4. TPM connector (20-1 pin TPM) This connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity. Chapter 2 5. 2-26 Serial port connector (10-1 pin COM1) This connector is for a serial (COM) port.
Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF Out module cable to this connector, then install the module to a slot opening at the back of the system chassis. Chapter 2 6. The S/PDIF module is purchased separately.
7. CPU, CPU OPT, Chassis fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin CHA_FAN1/2/3/4) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. Chapter 2 Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. • Chapter 2 8. We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
9. Chapter 2 2-30 ATX power connectors (24-pin EATXPWR; 8-pin EATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 450 W.
10. System panel connector (20-8 pin PANEL) • • • • • Chapter 2 This connector supports several chassis-mounted functions. System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity LED (2-pin IDE_LED) This 2-pin connector is for the HDD Activity LED.
2.3 Building your computer system 2.3.1 Additional tools and components to build a PC system Chapter 2 1 bag of screws Philips (cross) screwdriver PC chassis Power supply unit Intel LGA 2011 CPU Intel LGA 2011 compatible CPU Fan DIMM SATA hard disk drive SATA optical disc drive (optional) Graphics card (optional) The tools and components in the table above are not included in the motherboard package.
2.3.2 CPU installation Please note the order in opening/ closing the double latch. Follow the instructions printed on the metal sealing hatch or the illustrations shown below in this manual. The plastic cap will pop up automatically once the CPU is in place and the hatch properly sealed down.
5 6 Triangle mark Chapter 2 7 8 B A 9 A 2-34 B Chapter 2: Hardware information
2.3.3 CPU heatsink and fan assembly installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary.
2.3.
2.3.5 Motherboard installation The diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps remain the same.
3 Chapter 2 DO NOT overtighten the screws! Doing so can damage the motherboard.
2.3.
2.3.
2.3.8 Front I/O Connector To install ASUS Q-Connector 1 2 PWR Ground Reset Ground IDE_LED R SW POWE RESET SW To install USB 2.0 Connector Chapter 2 IDE_LED+ IDE_LED- To install front panel audio connector AAFP USB 2.
2.3.
2.3.10 1. 2. 3. 4. 5. Download the BIOS ROM file from the ASUS service website (www.asus.com). Save the ROM file to a USB portable disk. On the rear I/O port, plug the USB disk to the USB port with the WHITE interior. (See rectangle box in the image below) Press the BIOS Flashback button for 3 seconds, and the light will begin to flash (on the third second). The BIOS Flashback function is enabled once the light starts to flash.
2.3.11 Rear panel connection 1 Chapter 2 5 2 6 3 7 8 4 9 10 11 12 Rear panel connectors 1. PS/2 keyboard and mouse port 7. IEEE 1394a port 2. USB 2.0 ports 8. Optical S/PDIF Out port 3. External SATA port 9. USB BIOS Flashback button 4. Intel® LAN (RJ-45) port* 10. USB 2.0 ports 1, 2, 3, and 4 5. USB 3.0 ports 3 and 4 11. USB 3.0 ports 1 and 2 6. Power eSATA 6G port 12.
Use Clear RTC RAM jumper to clear CMOS switch to clear BIOS setup information only when the system hangs due to overclocking. • DO NOT insert a different connector to the external SATA port. • Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows® OS environment and after the USB 3.0 driver installation. • USB 3.0 devices can only be used as data storage only. • We strongly recommend that you connect USB 3.0 devices to USB 3.
2.3.12 Audio I/O connections Audio I/O ports Connect to Headphone and Mic Chapter 2 Connect to Stereo Speakers Connect to 2.
Connect to 4.1 channel Speakers Chapter 2 Connect to 5.1 channel Speakers Connect to 7.1 channel Speakers When the DTS UltraPC II function is enabled, ensure to connect the rear speaker to the gray port.
2.4 Starting up for the first time 1. After making all the connections, replace the system case cover. 3. Connect the power cord to the power connector at the back of the system chassis. 2. 4. 5. Be sure that all switches are off. Connect the power cord to a power outlet that is equipped with a surge protector. Turn on the devices in the following order: a. Monitor c. System power b. 6.
Chapter 3 Chapter 3: 3.1 Knowing BIOS BIOS setup The new ASUS UEFI BIOS is an Unified Extensible Firmware Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond traditional keyboardonly BIOS controls to enable more flexible and convenient mouse input. Users can easily navigate the new UEFI BIOS with the same smoothness as their operating system. The term “BIOS” in this user manual refers to “UEFI BIOS” unless otherwise specified.
3.2.1 EZ Mode By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ Mode provides you an overview of the basic system information, and allows you to select the display language, system performance mode and boot device priority. To access the Advanced Mode, click Exit/Advanced Mode, then select Advanced Mode. The default screen for entering the BIOS setup program can be changed. Refer to the Setup Mode item in section �������� 3.7 Boot memu for details.
3.2.2 Advanced Mode The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations. To access the EZ Mode, click Exit, then select ASUS EZ Mode.
Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have their respective menu items. Back button This button appears when entering a submenu. Press or use the USB mouse to click this button to return to the previous menu screen.
3.3 Main menu The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program. The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings. Security ASUS P9X79 • If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC) RAM to clear the BIOS password. See section 2.2.7 Jumper for information on how to erase the RTC RAM.
Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. Otherwise, you might be able to see or change only selected fields in the BIOS setup program. To set an administrator password: 1. Select the Administrator Password item and press . 3. Confirm the password when prompted. 2. From the Create New Password box, key in a password, then press . To change an administrator password: 1. 2. 3. 4.
3.4 Ai Tweaker menu The Ai Tweaker menu items allow you to configure overclocking-related items. Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field values can cause the system to malfunction. Chapter 3 The configuration options for this section vary depending on the CPU and DIMM model you installed on the motherboard.
Scroll down to display the following items: Ai Overclock Tuner [Auto] Allows you to select the CPU overclocking options to achieve the desired CPU internal frequency. Select any of these preset overclocking configuration options: [Auto] [Manual] [X.M.P.] Chapter 3 Loads the optimal settings for the system. Allows you to individually set overclocking parameters. If you install memory modules supporting the eXtreme Memory Profile (X.M.P.
Turbo Ratio [Auto] Allows you to manually adjust the Trubo CPU ratio. [Auto] All Turbo ratio are set by Intel CPU default settings [By ALL Cores (Can Adjust in OS)] All numbers of active cores will be set to one single Turbo ratio in OS [By Per Core (Cannot Adjust in OS)] All numbers of active cores can be set to an individual Turbo ratio in BIOS.
3.4.1 DRAM Timing Control The sub-items in this menu allow you to set the DRAM timing control features. Use the <+> and <-> keys to adjust the value. To restore the default setting, type [auto] using the keyboard and press the key. Changing the values in this menu may cause the system to become unstable! If this happens, revert to the default settings.
Scroll down to display the following items: Chapter 3 Scroll down to display the following items: ASUS P9X79 3-11
Scroll down to display the following items: Primary Timings DRAM CAS# Latency [Auto] Use the <+> and <-> keys to adjust the value. The ���������������������������������������������� values range from 3 to 15 with 1 interval. DRAM RAS# to CAS# Delay [Auto] Use the <+> and <-> keys to adjust the value. The ���������������������������������������������� values range from 4 to 15 with 1 interval. Chapter 3 DRAM RAS# PRE Time [Auto] Use the <+> and <-> keys to adjust the value.
DRAM READ to PRE Time [Auto] Use the <+> and <-> keys to adjust the value. The ���������������������������������������������� values range from 4 to 15 with 1 interval. DRAM FOUR ACT WIN Time [Auto] Use the <+> and <-> keys to adjust the value. The ����������������������������������������������� values range from 16 to 63 with 1 interval. DRAM WRITE to READ Delay [Auto] Use the <+> and <-> keys to adjust the value.
DRAM IOL (CHA D0 R0) [Auto] Configuration options: [Auto] [Advance 14 Clock] [Advance 13 Clock] [Advance 12 Clock] [Advance 11 Clock] [Advance 10 Clock] [Advance 9 Clock] [Advance 8 Clock] [Advance 7 Clock] [Advance 6 Clock] [Advance 5 Clock] [Advance 4 Clock] [Advance 3 Clock] [Advance 2 Clock] [Advance 1 Clock] [Normal] [Delay 1 Clock] [Delay 2 Clock] [Delay 3 Clock] [Delay 4 Clock] [Delay 5 Clock] [Delay 6 Clock] [Delay 7 Clock] [Delay 8 Clock] [Delay 9 Clock] [Delay 10 Clock] [Delay 11 Clock] [Delay 12
DRAM RTL (CHB D0 R0) [Auto] Configuration options: [Auto] [Advance 14 Clock] [Advance 12 Clock] [Advance 10 Clock] [Advance 8 Clock] [Advance 6 Clock] [Advance 4 Clock] [Advance 2 Clock] [Normal] [Delay 2 Clock] [Delay 4 Clock] [Delay 6 Clock] [Delay 8 Clock] [Delay 10 Clock] [Delay 12 Clock] [Delay 14 Clock] DRAM IOL (CHB D0 R0) [Auto] [Auto] [Advance 14 Clock] [Advance 13 Clock] [Advance 12 Clock] [Advance 11 Clock] [Advance 10 Clock] [Advance 9 Clock] [Advance 8 Clock] [Advance 7 Clock] [Advance 6 Clo
DRAM IOL (CHB D1 R1) [Auto] [Auto] [Advance 14 Clock] [Advance 13 Clock] [Advance 12 Clock] [Advance 11 Clock] [Advance 10 Clock] [Advance 9 Clock] [Advance 8 Clock] [Advance 7 Clock] [Advance 6 Clock] [Advance 5 Clock] [Advance 4 Clock] [Advance 3 Clock] [Advance 2 Clock] [Advance 1 Clock] [Normal] [Delay 1 Clock] [Delay 2 Clock] [Delay 3 Clock] [Delay 4 Clock] [Delay 5 Clock] [Delay 6 Clock] [Delay 7 Clock] [Delay 8 Clock] [Delay 9 Clock] [Delay 10 Clock] [Delay 11 Clock] [Delay 12 Clock] [Delay 13 Clock
DRAM RTL (CHC D1 R1) [Auto] Configuration options: [Auto] [Advance 14 Clock] [Advance 12 Clock] [Advance 10 Clock] [Advance 8 Clock] [Advance 6 Clock] [Advance 4 Clock] [Advance 2 Clock] [Normal] [Delay 2 Clock] [Delay 4 Clock] [Delay 6 Clock] [Delay 8 Clock] [Delay 10 Clock] [Delay 12 Clock] [Delay 14 Clock] DRAM IOL (CHC D1 R1) [Auto] [Auto] [Advance 14 Clock] [Advance 13 Clock] [Advance 12 Clock] [Advance 11 Clock] [Advance 10 Clock] [Advance 9 Clock] [Advance 8 Clock] [Advance 7 Clock] [Advance 6 Clo
DRAM IOL (CHD D1 R0) [Auto] [Auto] [Advance 14 Clock] [Advance 13 Clock] [Advance 12 Clock] [Advance 11 Clock] [Advance 10 Clock] [Advance 9 Clock] [Advance 8 Clock] [Advance 7 Clock] [Advance 6 Clock] [Advance 5 Clock] [Advance 4 Clock] [Advance 3 Clock] [Advance 2 Clock] [Advance 1 Clock] [Normal] [Delay 1 Clock] [Delay 2 Clock] [Delay 3 Clock] [Delay 4 Clock] [Delay 5 Clock] [Delay 6 Clock] [Delay 7 Clock] [Delay 8 Clock] [Delay 9 Clock] [Delay 10 Clock] [Delay 11 Clock] [Delay 12 Clock] [Delay 13 Clock
MCH Duty Sense (CHD) [Auto] Use the <+> and <-> keys to adjust the value. The values range from 0 to 31 with 1 interval. MCH Recheck [Auto] Configuration options: [Auto] [Disabled] [Enabled] DIGI+ Power Control Chapter 3 3.4.2 CPU Load-Line Calibration [Auto] CPU Load-line is defined by Intel VRM spec and affects CPU voltage. The CPU working voltage will decrease proportionally to CPU loading.
CPU Current Capability [Auto] This item provides wider total power range for overclocking. A higher value brings a wider total power range and extends the overclocking frequency range simultaneously. Configuration options: [Auto] [100%] [110%] [120%] [130%] [140%] Do not remove the thermal module while changing the DIGI+ Power Control related parameters . The thermal conditions should be monitored.
CPU Power Duty Control [T.Probe] [T.Probe] [Extreme] Maintains the VRM thermal balance. Maintains the VRM current balance. CPU Power Phase Control [Auto] Phase number is the number of woorking VRM phase. Increasing phase number under heavy system loading to get more transient and better thermal performance. Reducing phase number under light system loading to increase VRM efficiency [Standard] [Optimized] [Extreme] [Manual Adjustment] Proceeds phase control depending on the CPU loading.
3.4.3 CPU Performance Settings The items in this menu ���������������������������������� is setting for CPU Ratio/Features. CPU Ratio [Auto] Chapter 3 This item allows user manually adjust the maximum non-turbo CPU ratio, The value will be limit to CPU base or factory setting.
Turbo Mode Parameters Long Duration Power Limit [Auto] The default setting of this item will be TDP (130W). For Sandy Bridge-E, Turbo Ratio can be kept a time duration exceed TDP for maximum performance. Any value under 255 can be programmed. Use the <+> and <-> keys to adjust the value. Long Duration Maintained [Auto] This value can vary from 1 to 32, which indicates the time window for Turbo Ratio over TDP should be maintained. Use the <+> and <-> keys to adjust the value.
DRAM Voltage (CHA, CHB) [Auto] Allows you to set the DRAM voltage. The values range from 1.20V to 1.99V with a 0.005V interval. DRAM Voltage (CHC, CHD) [Auto] Allows you to set the DRAM voltage. The values range from 1.20V to 1.99V with a 0.005V interval. According to Intel CPU spec, DIMMs with voltage requirement over 1.65V may damage the CPU permanently. We recommend you install the DIMMs with the voltage requirement below 1.65V. CPU PLL Voltage [Auto] Allows you to set the CPU and PCH PLL voltage.
DRAM DATA REF Voltage on CHA [Auto] Allows you to set the DRAM DATA REF Voltage on CHA. The values range from 0.3950x to 0.6300x with a 0.005x interval. DRAM CTRL REF Voltage on CHB [Auto] Allows you to set the DRAM CTRL REF Voltage on CHB. The values range from 0.3950x to 0.6300x with a 0.005x interval. DRAM DATA REF Voltage on CHB [Auto] Allows you to set the DRAM DATA REF Voltage on CHB. The values range from 0.3950x to 0.6300x with a 0.005x interval.
DRAM Read REF Voltage on CHD [Auto] Allows you to set the DRAM Read Reference Voltage on Channel D. The values range from 0.3850x to 0.6150x with a 0.005x interval. Different ratio might enhance DRAM overclocking ability. CPU Freq Spread Spectrum [Auto] [Auto] [Disabled] [Enabled] Sets to Auto mode. Enhances the BCLK overclocking ability. Sets to [Enabled] for EMI control. PCIE Freq Spread Spectrum [Auto] [Auto] [Disabled] [Enabled] 3.5 Sets to Auto mode. Enhances the PCIE overclocking ability.
3.5.1 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. The items shown in this screen may be different due to the CPU you installed. UEFI BIOS Utility - Advanced Mode Main Back Ai Tweaker Exit Advanced Monitor Boot Tool Advanced\ CPU Configuration > CPU Configuration Genuine Intel(R) CPU @ 2.
Active Processor Cores [All] Allows you to choose the number of CPU cores to activate in each processor package. The configuration options will be vary with CPU specification. Configuration options: [All] Limit CPUID Maximum [Disabled] [Enabled] [Disabled] Allows legacy operating systems to boot even without support for CPUs with extended CPUID functions. Disables this function. [Enabled] [Disabled] Enables the No-Execution Page Protection Technology.
CPU C1E [Auto] [Auto] [Disabled] [Enabled] Set this function in Auto mode. Disables this function. Enables the C1E support function. This item should be enabled in order to enable the Enhanced Halt State. CPU C3 Report [Auto] Allows you to disable or enable the CPU C3 report to OS. Configuration options: [Enabled] [Disabled] [Auto] CPU C6 Report [Auto] Allows you to disable or enable the CPU C6 report to OS.
SATA Mode [AHCI Mode] Allows you to set the SATA configuration. [Disabled] [IDE Mode] [AHCI Mode] [RAID Mode] Disables the SATA function. Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices. Set to [AHCI Mode] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface).
SATA3G_3 (Blue) Hot Plug [Disabled] This item appear only when you set the previous item to [AHCI Mode] and [RAID Mode]. It’s allow user to enabled/disabled SATA Hot Plug Support. ���������������������������������� Configuration options: [Disabled] [Enabled]. SATA3G_4 (Blue) Hot Plug [Disabled] This item appear only when you set the previous item to [AHCI Mode] and [RAID Mode]. It’s allow user to enabled/disabled SATA Hot Plug Support.
3.5.5 USB Configuration The items in this menu allow you to change the USB-related features. UEFI BIOS Utility - Advanced Mode Ai Tweaker Main Back Advanced Exit Monitor Boot Tool Advanced\ USB Configuration > USB Configuration USB Devices: 1 Keyboard, 1 Mouse, 4 Hubs Legacy USB Support Enabled Legacy USB3.0 Support Enabled EHCI Hand-off Disabled Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected.
3.5.6 Onboard Devices Configuraton UEFI BIOS Utility - Advanced Mode Ai Tweaker Main Back Exit Advanced Monitor Boot Tool Advanced\ Onboard Devices Configuration > Azalia HD Audio Enabled Front Panel Type HD SPDIF Out Type SPDIF Intel LAN Controller Enabled Intel LAN PXE OPROM Disabled VIA 1394 Controller Enabled Asmedia USB 3.
Intel LAN PXE OPROM [Disabled] This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the PXE OptionRom of the Intel LAN controller. Configuration options: [Enabled] [Disabled] VIA 1394 Controller [Enabled] This item allows you to enable or disable VIA 1394. Configuration options: [Enabled] [Disabled] Asmedia USB 3.0 Controller [Enabled] This item allows user to enabled/disabled Asmedia USB 3.0.
3.5.7 APM UEFI BIOS Utility - Advanced Mode Ai Tweaker Main Back Advanced Exit Monitor Boot Tool Advanced\ APM > Restore AC Power Loss Power Off Power On By Keyboard Disabled Power On By Mouse Disabled Power On By PCIE/PCI Disabled Power On By Ring Disabled Power On By RTC Disabled ErP Ready Disabled Specify what state to go to when power is re-applied after a power failure (G3 state).
3.6 Monitor menu The Monitor menu displays the system temperature/power status, and allows you to change the fan settings.
MB Temperature ������������� [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the motherboard temperatures. Select Ignore if you do not wish to display the detected temperatures. CPU Fan Speed [xxxx RPM] or [Ignore] / [N/A] CPU OPT Fan Speed [xxxx RPM] or [Ignore] / [N/A] Chassis Fan 1/2/3/4 Speed [xxxx RPM] or [Ignore] / [N/A] The onboard hardware monitor automatically detects and displays the CPU, CPU OPT, and chassis fan speed in rotations per minute (RPM).
Chassis 1/2/3/4 Q-Fan Control [Enabled] [Disabled] [Enabled] Disables the Chassis Q-Fan control feature. Enables the Chassis Q-Fan control feature. Chassis 1/2/3/4 Fan Speed Low Limit [600 RPM] This item appears only when you enable the Chassis 1/2/3/4 Q-Fan Control feature and allows you to disable or set the chassis fan warning speed.
3.7 Boot menu The Boot menu items allow you to change the system boot options. Bootup NumLock State [On] Sets the power-on state of the NumLock to [On]. Sets the power-on state of the NumLock to [Off]. Chapter 3 [On] [Off] Full Screen Logo [Enabled] [Enabled] [Disabled] Enables the full screen logo display feature. Disables the full screen logo display feature. Set this item to [Enabled] to use the ASUS MyLogo 2™ feature.
Setup Mode [EZ Mode] [Advanced Mode] Sets Advanced Mode as the default screen for entering the BIOS setup program. [EZ Mode] Sets EZ Mode as the default screen for entering the BIOS setup program. Boot Option Priorities These items specify the boot device priority sequence from the available devices. The number of device items that appears on the screen depends on the number of devices installed in the system. • • To select the boot device during system startup, press when ASUS Logo appears.
3.8 Tools menu The Tools menu items allow you to configure options for special functions. Select an item then press to display the submenu. UEFI BIOS Utility - Advanced Mode Ai Tweaker Main Advanced Exit Monitor Boot Tool Be used to update BIOS > ASUS EZ Flash 2 Utility > ASUS DRAM SPD Information > ASUS O.C. Profile 3.8.1 ASUS EZ Flash 2 Utility Allows you to run ASUS EZ Flash 2 Utility. When you press , a confirmation message appears.
3.8.2 ASUS DRAM SPD Information This menu showed the DIMM slot related informatons.
3.8.3 ASUS O.C. Profile This item allows you to store or load multiple BIOS settings. UEFI BIOS Utility - Advanced Mode Ai Tweaker Main Back Exit Advanced Monitor Boot Tool Tool\ ASUS O.C. Profile > O.C.
3.9 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit menu. Exit Load Optimized Defaults Save Changes & Reset Discard Changes & Exit ASUS EZ Mode Launch UEFI Shell from filesystem device Load Optimized Defaults This option allows you to load the default values for each of the parameters on the Setup menus.
3.10 Updating BIOS The ASUS website publishes the latest BIOS versions to provide enhancements on system stability, compatibility, or performance. However, BIOS updating is potentially risky. If there is no problem using the current version of BIOS, DO NOT manually update the BIOS. Inappropriate BIOS updating may result in the system’s failure to boot. Carefully follow the instructions of this chapter to update your BIOS if necessary. Visit the ASUS website (www.asus.
Updating the BIOS through the Internet To update the BIOS through the Internet: 1. From the ASUS Update screen, select Update BIOS from Internet, and then click Next. 2. Select the ASUS FTP site nearest you to avoid network traffic. If you want to enable the BIOS downgradable function and auto BIOS backup function, check the checkboxs before the two items on the screen. Select the BIOS version that you want to download. Click Next. 4.
Updating the BIOS through a BIOS file 1. From the ASUS Update screen, select Update BIOS from file, and then click Next. 2. Locate the BIOS file from the Open window, click Open, and click Next. 3. You can decide whether to change the BIOS boot logo. Click Yes if you want to change the boot logo or No to continue. 4. Chapter 3 To update the BIOS through a BIOS file: Follow the onscreen instructions to complete the update process.
3.10.2 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to use a bootable floppy disk or an OS‑based utility. Before you start using this utility, download the latest BIOS from the ASUS website at www.asus.com. To update the BIOS using EZ Flash 2: 1. Insert the USB flash disk that contains the latest BIOS file to the USB port. 2. ������������������������������������������������������������� Enter the Advanced Mode of the BIOS setup program.
• This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only. • DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu. See section 3.9 Exit Menu for details. 3.10.
3.10.4 ASUS BIOS Updater The ASUS BIOS Updater allows you to update BIOS in DOS environment. This utility also allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or gets corrupted during the updating process. The succeeding utility screens are for reference only. The actual utility screen displays may not be same as shown. Before updating BIOS 1. 2. 3. Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and single partition.
Backing up the current BIOS To backup the current BIOS file using the BIOS Updater Ensure that the USB flash drive is not write-protected and has enough free space to save the file. 1. At the FreeDOS prompt, type bupdater /o[filename] and press . D:\>bupdater /oOLDBIOS1.rom Filename Extension The [filename] is any user-assigned filename with no more than eight alphanumeric characters for the filename and three alphanumeric characters for the extension. 2.
Updating the BIOS file To update the BIOS file using BIOS Updater 1. At the FreeDOS prompt, type bupdater /pc /g and press . D:\>bupdater /pc /g 2. The BIOS Updater screen appears as below. ASUSTek BIOS Updater for DOS V1.18 [2011/04/29] Current ROM BOARD: P9X79 VER: 0228 DATE: 08/26/2011 Update ROM BOARD: Unknown VER: Unknown DATE: Unknown PATH: A:\ P8P67D.ROM A: 4194304 2011-08-05 17:30:48 Note [Enter] Select or Load [Up/Down/Home/End] Move 3.
Chapter 4 Chapter 4: 4.1 Software support Installing an operating system This motherboard supports Windows® XP/ 64-bit XP/ Vista / 64-bit ���������������������������� Vista / 7 / 64-bit 7� operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 4.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
4.2.2 Obtaining the software manuals The software manuals are included in the support DVD. Follow the instructions below to get the necessary software manuals. The software manual files are in Portable Document Format (PDF). Install the Adobe® Acrobat® Reader from the Utilities menu before opening the files. 1. Click on the Manual tab. Click on ASUS Motherboard Utility Guide from the manual list on the left. 2. The Manual folder of the support DVD appears.
4.3 Software information Most of the applications in the support DVD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. 4.3.1 AI Suite II AI Suite II is an all-in-one interface that integrates several ASUS utilities and allows users to launch and operate these utilities simultaneously. Installing AI Suite II To install AI Suite II on your computer 1. 2. 3.
4.3.2 TurboV EVO ASUS TurboV EVO introduces TurboV that allows you to manually adjust the CPU frequency and related voltages as well as Auto Tuning function that offers automatic and easy overclocking and system level up. After installing AI Suite II from the motherboard support DVD, launch TurboV EVO by clicking Tool > TurboV EVO on the AI Suite II main menu bar. Refer to the software manual in the support DVD or visit the ASUS website at www.asus.com for detailed software configuration.
Using Advanced Mode Click on the Advanced Mode tab to adjust the advanced voltage settings. Advanced mode Target values Voltage Adjustment bars Undoes all changes without applying Current values Click to restore all start-up settings Applies all changes immediately CPU Ratio Allows you to manually adjust the CPU ratio. 1. 2. 3. 4. Click on the CPU Ratio tab. Click ON to activate the CPU Ratio function. The system automatically reboots for the changes to take effect.
CPU Strap Allows you to manually adjust CPU Strap. 1. 2. 3. Click on the CPU Strap tab. Click on the adjustment bar to the desired value. The graph on the right will change value accordingly. Click on Apply to make the change take effect. CPU Strap Adjustment bar Undoes all changes without applying Click to restore all start-up settings Applies all changes immediately • Apply settings in CPU Ratio affect CPU Strap results. • The value on the CPU Strap diagram varies with your CPU model.
3. TurboV automatically overclocks the CPU, saves BIOS settings and restarts the system. After re-entering Windows, a message appears indicating auto tuning success. Click OK to exit. Using Extreme Tuning 2. Click the Auto Tuning tab and then click Extreme. Read through the warning messages and click OK to start auto-overclocking. 3. TurboV automatically overclocks the CPU and memory and restarts the system. After re-entering Windows, a message appears indicating the current overclocking result.
4.3.3 DIGI+ Power Control DIGI+ PowerControl allows you to adjust VRM voltage and frequency modulation to enhance reliability and stability. It also provides the highest power efficiency, generating less heat to longer component lifespan and minimize power loss. After installing AI Suite II from the motherboard support DVD, launch DIGI+ Power Control by clicking Tool > DIGI+ Power Control on the AI Suite II main menu bar. Select CPU Power or DRAM Power to adjust the power control settings.
DRAM Power 1 Application aids 2 3 Apply all changes immediately Undo all changes without applying Function no. Function description 1 DRAM Current Capability A higher value brings a wider total power range and extends the overclocking frequency range simultaneously. 2 DRAM Voltage Frequency Allows you to adjust the DRAM switching frequency for system stability or to increase OC Range.
4.3.4 EPU EPU is an energy-efficient tool that satisfies different computing needs. This utility provides several modes that you can select to save system power. Selecting Auto mode will have the system shift modes automatically according to current system status. You can also customize each mode by configuring settings like CPU frequency, GPU frequency, vCore Voltage, and Fan Control.
4.3.5 FAN Xpert+ FAN Xpert+ intelligently allows you to adjust both the CPU and chassis fan speeds according to different ambient temperatures caused by different climate conditions in different geographic regions and your PC’s system loading. The built-in variety of useful profiles offer flexible automatic and manual fan speed controls to achieve a quiet and cool environment.
4.3.6 Sensor Recorder Sensor Recorder monitors the changes in the system voltage, temperature, and fan speed on a timeline. The History Record function allows you to designate specific time spans on record to keep track of the three system statuses for certain purposes. Launching Sensor Recorder After installing AI Suite II from the motherboard support DVD, launch Sensor Recorder by clicking Tool > Sensor Recorder on the AI Suite II main menu bar.
4.3.7 Probe II Probe II is a utility that monitors the computer’s vital components, and detects and alerts you of any problem with these components. Probe II senses fan rotations, CPU temperature, and system voltages, among others. With this utility, you are assured that your computer is always at a healthy operating condition. Launching Probe II After installing AI Suite II from the motherboard support DVD, launch Probe II by clicking Tool > Probe II on the AI Suite II main menu bar.
4.3.8 USB 3.0 Boost The ASUS exclusive USB 3.0 Boost provides speed boost for USB 3.0 devices and the up-to-date support of USB Attached SCSI Protocol (UASP). With USB 3.0 Boost, you can accelerate the transfer speed of your USB 3.0 devices with ease. Launching USB 3.0 Boost After installing AI Suite II from the motherboard support DVD, launch USB 3.0 Boost by clicking Tool > USB 3.0 Boost on the AI Suite II main menu bar. Configuring USB 3.0 Boost 1. 2. 3. Connect a USB 3.0 device to the USB 3.
4.3.9 ASUS Update ASUS Update lays out the options for updating BIOS on your system. Update BIOS utility on your system or simply save the utility for later use just by following the directions on this convenient updating feature. Launching ASUS Update After installing AI Suite II from the motherboard support DVD, launch ASUS Update by clicking Update> ASUS Update on the AI Suite II main menu bar. Using ASUS Update Select the way you would like to do with the BIOS utility.
4.3.10 MyLogo2 This MyLogo utility lets you customize the boot logo. The boot logo is the image that appears on screen during the Power‑On‑Self-Tests (POST). Personalize your computer from the very beginning! Launching ASUS Update After installing AI Suite II from the motherboard support DVD, launch MyLogo by clicking Update> MyLogo on the AI Suite II main menu bar. Using MyLogo Select the way you would like to do update your boot logo. Then click Next and follow the given instructions.
2. Click on Auto Tune to adjust image size compatibility or adjust the resolution bar. 4. Click on Flash to start updating the image to the boot logo. 3. 5. You can click on Booting Preview to preview the boot image. Then click Next. Click on Yes to reboot or you can also see the new logo next time you restart your computer. Change the boot logo of a downloaded BIOS file and update (or do not update) this BIOS to the motherboard 2. 3.
4.3.11 Audio configurations The Realtek audio CODEC provides 8-channel audio capability to deliver the ultimate audio experience on your computer. The software provides Jack-Sensing function, S/PDIF Out support, and interrupt capability. The CODEC also includes the Realtek® proprietary UAJ® (Universal Audio Jack) technology for all audio ports, eliminating cable connection errors and giving users plug and play convenience.
4.4 RAID configurations The motherboard supports the following SATA RAID solutions: Intel® Rapid Storage Technology with RAID 0, RAID 1, RAID 10 and RAID 5 support. 4.4.1 • You must install Windows® XP Service Pack 3 or later versions before using Serial ATA hard disk drives. The Serial ATA RAID feature is available only if you are using Windows® XP SP3 or later versions. • Due to Windows® XP / Vista limitation, a RAID array with the total capacity over 2TB cannot be set as a boot disk.
4.4.2 Installing Serial ATA hard disks The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array. To install the SATA hard disks for a RAID configuration: 1. Install the SATA hard disks into the drive bays. 3. Connect a SATA power cable to the power connector on each drive. 2. Connect the SATA signal cables. 4.4.
The navigation keys at the bottom of the screen allow you to move through the menus and select the menu options. The RAID BIOS setup screens shown in this section are for reference only and may not exactly match the items on your screen. The utility supports maximum four hard disk drives for RAID configuration. Creating a RAID set To create a RAID set: 1. From the utility main menu, select 1. Create RAID Volume and press .
5. 6. Use the up/down arrow key to select a drive, and then press to select. A small triangle marks the selected drive. Press after completing your selection. Use the up/down arrow key to select the stripe size for the RAID array (for RAID 0, 10 and 5 only),and then press . The available stripe size values range from 4KB to 128KB.
Deleting a RAID set Take caution when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set: 1. From the utility main menu, select 2. Delete RAID Volume and press . The following screen appears: Intel(R) Rapid Storage Technology - Option ROM - v10.0.0.1032 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved. [ DELETE VOLUME MENU ] Name Volume0 Level RAID0(Stripe) Drives 2 Capacity 298.
4.5 Creating a RAID driver disk A floppy disk with the RAID driver is required when installing a Windows® operating system on a hard disk drive that is included in a RAID set. 4.5.1 • The motherboard does not provide a floppy drive connector. You have to use a USB floppy disk drive when creating a SATA RAID driver disk. • Windows® XP may not recognize the USB floppy disk drive due to Windows® XP limitation. To work around this OS limitation, refer to section 4.5.4 Using a USB floppy disk drive.
4.5.3 Installing the RAID driver during Windows® OS installation To install the RAID driver in Windows® XP: 1. 2. 3. 4. During the OS installation, the system prompts you to press the F6 key to install thirdparty SCSI or RAID driver. Press , and then insert the floppy disk with RAID driver into the USB floppy disk drive. When prompted to select the SCSI adapter to install, select the RAID driver for the corresponding OS version.
4.5.4 Using a USB floppy disk drive Due to OS limitation, Windows® XP may not recognize the USB floppy disk drive when you install the RAID driver from a floppy disk during the OS installation. To solve this issue, add the USB floppy disk drive’s Vendor ID (VID) and Product ID (PID) to the floppy disk containing the RAID driver. Refer to the steps below: 1. Using another computer, plug the USB floppy disk drive, and insert the floppy disk containing the RAID driver. 2.
7. Use Notepad to open the file. 8. Find the [HardwareIds.scsi.iaAHCI_DesktopWorkstationServer] and [HardwareIds.scsi.iaStor_DesktopWorkstationServer] sections in the txtsetup.oem file. 9. Type the following line to the bottom of the two sections: id = “USB\VID_xxxx&PID_xxxx”, “usbstor” [HardwareIds.scsi.iaAHCI_DesktopWorkstationServer] id= “PCI\VEN_8086&DEV_1C02&CC_0106”,”iaStor” id= “USB\VID_03EE&PID_6901”, “usbstor” [HardwareIds.scsi.
Chapter 4 4-28 Chapter 4: Software support
Chapter 5 Chapter 5: Multiple GPU technology support 5.1 AMD® CrossFireX™ technology The motherboard supports the AMD CrossFireX™ technology that allows you to install multi-graphics processing units (GPU) graphics cards. Follow the installation procedures in this section. ® 5.1.1 • • • Requirements In Dual CrossFireX mode, you should have two identical CrossFireX-ready graphics cards or one CrossFireX-ready dual-GPU graphics card that are AMD® certified.
5.1.3 Installing two CrossFireX™ graphics cards Chapter 5 The following pictures are for reference only. The graphics cards and the motherboard layout may vary with models, but the installation steps remain the same. 1. 2. 3. 4. Prepare two CrossFireX-ready graphics cards. Insert the two graphics card into the PCIEX16 slots.
5.1.4 Installing the device drivers Refer to the documentation that came with your graphics card package to install the device drivers. 5.1.5 Enabling the AMD® CrossFireX™ Chapter 5 Ensure that your PCI Express graphics card driver supports the AMD® CrossFireX™ technology. Download the latest driver from the AMD website (www.amd.com). technology After installing your graphics cards and the device drivers, enable the CrossFireX™ feature through the AMD Catalyst™ Control Center in Windows environment.
5.2 NVIDIA® SLI™ technology The motherboard supports the NVIDIA® SLI™ (Scalable Link Interface) technology that allows you to install multi-graphics processing units (GPU) graphics cards. Follow the installation procedures in this section. Chapter 5 5.2.1 • • • Requirements In SLI mode, you should have two identical SLI-ready graphics cards that are NVIDIA® certified. Ensure that your graphics card driver supports the NVIDIA SLI technology. Download the latest driver from the NVIDIA website (www.
5. 6. Align and firmly insert the SLI bridge connector to the goldfingers on each graphics card. Ensure that the connector is firmly in place. Connect two independent auxiliary power sources from the power supply to the two graphics cards separately. Chapter 5 4. Connect a VGA or a DVI cable to the graphics card. SLI bridge Goldfingers 5.2.3 Installing the device drivers Refer to the documentation that came with your graphics card package to install the device drivers.
If you cannot see the NVIDIA Control Panel item in step (A), select Personalize. B2. From the Personalization window, select Display Settings. B3. From the Display Settings dialog box, click Advanced Settings. Chapter 5 B1.
Select the NVIDIA GeForce tab, and then click Start the NVIDIA Control Panel. B5. The NVIDIA Control Panel window appears. Chapter 5 B4. Enabling SLI settings From the NVIDIA Control Panel window, select Set SLI Configuration. Click Enable SLI and set the display for viewing SLI rendered content. When done, click Apply.
Chapter 5 5-8 Chapter 5: Multiple GPU technology support
ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax E-mail Web site Technical Support Telephone Online support 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 +886-2-2894-3447 +886-2-2890-7798 info@asus.com.tw www.asus.com.tw +86-21-38429911 support.asus.
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Date : Signature : Representative Person’s Name : Oct. 21, 2011 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.