Motherboard P9X79-E WS
E8097 First Edition March 2013 Copyright © 2013 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Notices ........................................................................................................................ vi Safety information..................................................................................................... viii About this guide.......................................................................................................... ix P9X79-E WS specifications summary.......................................................................
Contents 2.5 Turning off the computer.......................................................................... 2-52 Chapter 3: 3.1 3.2 3.3 3.4 3.5 BIOS setup program................................................................................... 3-3 3.2.1 3.2.2 Advanced menu........................................................................................ 3-24 3.5.1 CPU Configuration..................................................................... 3-25 3.5.3 PCH Configuration.......
Contents 4.3.4 DIGI+ Power Control.................................................................. 4-10 4.3.7 FAN Xpert+................................................................................ 4-13 4.3.6 4.3.8 4.3.9 4.3.10 4.3.11 4.3.12 4.4 4.3.13 Probe II...................................................................................... 4-16 TurboV EVO............................................................................... 4-17 USB 3.0 Boost......................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • • This device may not cause harmful interference, and This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
REACH Complying with the REACH (Registration, Evaluation, Authorization, and Restriction of Chemicals) regulatory framework, we published the chemical substances in our products at ASUS website at http://csr.asus.com/english/REACH.htm. ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment.
Safety information Electrical safety • • • • • • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
About this guide This user guide contains the information you need when installing and configuring the motherboard. How this guide is organized This guide contains the following parts: • • • • • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports. Chapter 2: Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components.
Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task. CAUTION: Information to prevent damage to the components when trying to complete a task. IMPORTANT: Instructions that you MUST follow to complete a task. NOTE: Tips and additional information to help you complete a task.
P9X79-E WS specifications summary CPU 2nd Generation Intel® Core™ i7 Processor for the LGA 2011 Socket Intel® Xeon® E5-1600 processor for the LGA 2011 Socket Intel® Xeon® E5-2600 processor for the LGA 2011 Socket Supports Intel® Turbo Boost Technology 2.0 *Refer to www.asus.com for CPU support list Chipset Intel® X79 Express Chipset Memory 8 x DIMM, Max. 64GB, DDR3 2400 (O.C.)/ 2133 (O.C.)/1866 (O.C.
P9X79-E WS specifications summary 1394 VIA VT6315N controller support 1x1394a port Audio Realtek® ALC 1150 8-channel High Definition Audio CODEC - Supports 192kHz/ 24bit BD Lossless Sound - DTS Surround Sensation UltraPC II - Supports Jack-Detection, Multi-Streaming, and Front Panel Jack-Retasking - Optical S/PDIF Out port at back I/O ASUS Unique Features Industry leading Digital 8+2 Phase Power Design Industry leading Digital 2+2 Phase Power Design ASUS TPU ASUS EPU ASUS Exclusive Features - ASU
P9X79-E WS specifications summary Back Panel I/O Ports 2 x USB 3.0/2.0 ports (blue) 10 x USB 2.0/1.1 ports (white port can be switched to USB BIOS Flashback) 1 x USB BIOS Flashback Switch 1 x PS/2 KB/MS port 2 x eSATA 6Gb/s ports 2 x LAN (RJ45) ports (2 x Intel® LAN) 1 x optical S/PDIF Out port 8-channel Audio I/O Internal I/O Connectors 1 x USB 3.0/2.0 connector support additional 2 USB ports (19-pin) 1 x USB 2.0/1/1 connectors support additional 2 USB ports 1 x USB 2.0/1.
xiv
Chapter 1: Product Introduction
Chapter summary 1 This chapter describes the motherboard features and the new technologies it supports. This chapter contains the following sections: 1.1 1.2 1.3 Welcome!..................................................................................................... 1-3 Package contents....................................................................................... 1-3 Special features..........................................................................................
1.1 Welcome! Thank you for buying an ASUS P9X79-E WS motherboard! The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards! Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below. 1.2 Package contents Check your motherboard package for the following items. Motherboard ASUS P9X79-E WS I/O modules 1 x 2-port USB 2.
1.3 Special features 1.3.1 Product highlights Intel Socket 2011 for 2nd Generation Intel® Core™ i7 Processor Extreme Edition ® This motherboard supports the latest Intel® 2nd Generation Core™ i7 Processor Extreme in LGA2011 package, with memory and PCI Express controllers integrated to quadchannel (8 DIMMs) DDR3 memory and 40 PCI Express 2.0 lanes. This provides great graphicsperformance.
Power eSATA 6Gb/s Ready 2X faster with fully charged power Powered eSATA 6Gb/s combines data and power connectivity. Users enjoy 2X faster transfer rates, and can use external SATA 6Gb/s devices with no additional power adapters. ASUS provides two extra ports with enhanced scalability, faster data retrieval, and double the bandwidth of current bus systems for extra speed and accessibility. 1.3.
1.3.3 ASUS features New DIGI+ Power Control All-New Digital Power Control for both CPU and DRAM ASUS X79 motherboards include New DIGI+ Power Control with two digital voltage regulator modules (VRMs), including an all-new DRAM controller that allows ultra-precise memory tuning in addition to CPU voltage control. This evolution of innovative, industry-leading ASUS technology provides super-accurate voltages for better efficiency, stability and performance.
USB 3.0 Boost New ASUS USB 3.0 Boost technology supports UASP (USB Attached SCSI Protocol), the latest USB 3.0 standard. With USB 3.0 Boost technology, the performance of a USB device transmission speed is significantly increased up to 130% (TBD), adding to an already impressive fast USB 3.0 transfer speed. With USB 3.0 Boost technology, the system provides a user-friendly graphical interface, which spontaneously accelerates the transfer speed through USB 3.
ASUS Fanless Design—Heat-pipe solution The stylish heatsink offers 0dB cooling for a quiet PC environment. Attractive design enhances the look of the board and case, while temperatures in the chipset and power phase areas stay lower through high efficiency heat exchange. Combining usability and aesthetics,the stylish ASUS heatsink gives users an extremely silent and cool experience with elegant design. DO NOT uninstall the heat-pipe by yourself.
ASUS Q-Design ASUS Q-Design enhances your DIY experience. All of Q-LED, Q-Slot, Q-Code and Q-DIMM design speed up and simplify the DIY process! ASUS Q-Shield The specially designed ASUS Q-Shield does without the usual "fingers" - making it convenient and easy to install. With better electric conductivity, it ideally protects your motherboard against static electricity and shields it against Electronic Magnetic Interference (EMI).
1-10 Chapter 1: Product Introduction
Chapter 2: Hardware Information
Chapter summary 2 This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard. This chapter contains the following sections: 2.1 Before you proceed.................................................................................... 2-3 2.3 Building your computer system.............................................................. 2-37 2.2 2.4 2.5 Motherboard overview..............
2.1 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings. • Unplug the power cord from the wall socket before touching any component. • Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity. • Hold components by the edges to avoid touching the ICs on them.
2.2 Motherboard overview 2.2.1 Motherboard layout Refer to 2.2.9 Internal Connectors for more information about rear panel connectors and internal connectors.
2.2.2 Layout contents Connectors/Jumpers/Switches/Slots Page 2. 3. 4. 2-7 2-6 2-32 1. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. ATX Power connectors (24-pin EATXPWR, 8-pin EATX12V, 6-pin EATX12V_1) DDR3 DIMM slots LGA2011 CPU Socket CPU, CPU OPT, Chassis fan connectors (4-pin CPU_FAN, 4-pin CHA_OPT, 4-pin CHA_FAN1/2/3/4) Reset switch Power-on switch ASUS Dr._POWER switch MemOK! switch EPU Switch USB 3.0 connector (20-1 pin USB3_34) Intel® X79 Serial ATA 6.
2.2.3 Central Processing Unit (CPU) The motherboard comes with a surface mount LGA2011 socket designed for the 2nd Generation Intel® Core™ i7 Processor Extreme Edition. Ensure that all power cables are unplugged before installing the CPU. 2-6 • Upon purchase of the motherboard, ensure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components.
2.2.4 System memory The motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory Modules (DIMM) slots. A DDR3 module is notched differently from a DDR or DDR2 module. DO NOT install a DDR or DDR2 memory module to the DDR3 slot.
Memory configurations You may install 1GB, 2GB, 4GB, 8GB unbuffered ECC or non‑ECC DDR3 DIMMs into the DIMM sockets depending on the installed CPU. • You may install varying memory sizes in Channel A, Channel B, Channel C and Channel D. The system maps the total size of the lower-sized channel for the dualchannel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation. • According to Intel CPU spec, DIMM voltage below 1.
2.2.5 Expansion slots Ensure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components. No. Slot Description 1 PCIEX16_1 PCIe 3.0 x16_1 slot (single at x16 mode, blue) 2 PCIEX16_2 PCIe 3.0 x16_6 slot (x8 mode, black) 3 PCIEX16_3 PCIe 3.0 x16_1 slot (single at x16 or dual at x8/x8 mode, blue) 4 PCIEX16_4 PCIe 3.0 x16_6 slot (x8 mode, black) 5 PCIEX16_5 PCIe 3.
PCIe Express 3.0 operating mode Slot no. 1 Single VGA 3-WAY SLI/ CrossFireX SLI/CrossFireX x 16 (single VGA recommended x16 3 x16 (dual VGA recommended) 5 4-WAY SLI/ CrossFireX x16 x16 x16 x16 x16 x16 7 x16 • We recommend that you provide sufficient power when running CrossFireX™ or SLI™ mode. • Connect a chassis fan to the motherboard connector labeled CHA_FAN1-4 when using multiple graphics cards for better thermal environment.
2.2.6 Onboard switches Onboard switches allow you to fine-tune performance when working on a bare or opencase system. This is ideal for overclockers and gamers who continually change settings to enhance system performance. 1. 2. Power-on button The motherboard comes with a power-on switch that allows you to power up or wake up the system.
3. EPU switch Turning this switch to Enable will automatically detect the current PC loadings and intelligently moderate the power consumption. For ensuring system performance, turn the switch setting to Enable when the system is powered off. 4. TPU switch Turning this switch to Enable will automatically optimize the system for fast, yet stable clock speeds. For ensuring system performance, turn the switch setting to Enable when the system is powered off.
5. MemOK! switch Installing DIMMs that are incompatible with the motherboard may cause system boot failure, and the DIAGLED near the MemOK! switch lights continuously. Press and hold the MemOK! switch until the DIAG_LED starts blinking to begin automatic memory compatibility tuning for successful boot. • Refer to section 2.2.7 Onboard LEDs for the exact location of the DIAG_DRAM. • The DIAG_LED also lights when the DIMM is not properly installed.
6. 2-14 ASUS Dr. POWER switch This switch allows you to enable or disable the ASUS Dr. Power feature. Install the bundled ASUS Dr. Power Utility then enable this switch to allow the system to display notification messages in your Windows screen if a problem is detected with your power supply unit (PSU).
2.2.7 1. 2. Onboard LEDs Diagnosis LED These diagnosis LEDs of CPU, DRAM, VGA card, and HDD indicate key component status during POST (Power-on Self Test), providing an elegant embellishment to the motherboard design. The LED lights will flash sequentially during system bootup. If an error is found, the LED next to the error device will continue lighting until the problem is solved. This user-friendly design provides an intuitional way to locate the root problem in seconds.
3. 4. 2-16 TPU LED The TPU LED lights up when the TPU switch is turned to Enable. Q-Code LED The Q-Code LED design provides you the 2-digit display, allowing you to know the system status. Refer to the Q-Code table on the next page for details.
Q-Code table Code Description 00 Not used 01 Power on. Reset type detection (soft/hard).
Q-Code table (continued) 2-18 Code Description 31 Memory Installed 32 – 36 CPU post-memory initialization 37 – 3A Post-Memory System Agent initialization is started 3B – 3E Post-Memory PCH initialization is started 3F – 4E Post memory initialization codes 4F DXE IPL is started 50 – 53 Memory initialization error.
Q-Code table (continued) Code Description F5-F7 Reserved for future AMI progress codes F8 Recovery PPI is not available F9 Recovery capsule is not found FA Invalid recovery capsule FB-FF Reserved for future AMI error codes 60 DXE Core is started 61 NVRAM initialization 62 Installation of the PCH Runtime Services 63 – 67 CPU DXE initialization is started 68 PCI host bridge initialization 69 System Agent DXE initialization is started 6A System Agent DXE SMM initialization is started
Q-Code table (continued) 2-20 Code Description 97 Console Output devices connect 98 Console input devices connect 99 Super IO Initialization 9A USB initialization is started 9B USB Reset 9C USB Detect 9D USB Enable 9E-9F Reserved for future AMI codes A0 IDE initialization is started A1 IDE Reset A2 IDE Detect A3 IDE Enable A4 SCSI initialization is started A5 SCSI Reset A6 SCSI Detect A7 SCSI Enable A8 Setup Verifying Password A9 Start of Setup AA Reserved for ASL (s
Q-Code table (continued) Code Description AC Reserved for ASL (see ASL Status Codes section below) AD Ready To Boot event AE Legacy Boot event AF Exit Boot Services event B0 Runtime Set Virtual Address MAP Begin B1 Runtime Set Virtual Address MAP End B2 Legacy Option ROM Initialization B3 System Reset B4 USB hot plug B5 PCI bus hot plug B6 Clean-up of NVRAM B7 Configuration Reset (reset of NVRAM settings) B8– BF Reserved for future AMI codes C0– CF BDS initialization codes D0
ACPI/ASL Checkpoints Code Description 0x01 System is entering S1 sleep state 0x02 System is entering S2 sleep state 0x03 System is entering S3 sleep state 0x04 System is entering S4 sleep state 0x05 System is entering S5 sleep state 0x10 System is waking up from the S1 sleep state 0x20 System is waking up from the S2 sleep state 0x30 System is waking up from the S3 sleep state 0x40 System is waking up from the S4 sleep state 0xAC System has transitioned into ACPI mode.
6. 7. PGLED3 LED The ASUS Dr. Power LED near the ASUS Dr. Power switch lights up when the ASUS Dr. Power switch is turned to enable. +12V_PWR LED The ASUS Dr. Power LED near EATX12V connector lights up when the ASUS Dr. Power switch setting is turned to enable and there is no power detected going into the processor.
2.2.8 1. Jumper Clear RTC RAM (3-pin CLRTC) This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS. You can reset the system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords. To erase the RTC RAM 1. Turn OFF the computer and unplug the power cord. 3. Plug the power cord and turn ON the computer. 2. 4. Move the jumper cap from pins 1-2 (default) to pins 2-3.
2. Chassis Fan control setting (3-pin CHAFAN_SEL) These jumpers allow you to switch for fan pin selection. The CHAFAN_SEL jumper is for the front fans and rear fans control. Set to pins 1–2 when using 3-pin fans or pins 2–3 when using 4-pin fans. • If you use a 4-pin fan but set the jumper to pin 1-2, the fan you installed may not work. • If you use a 3-pin fan but set the jumper for a 4-pin fan, the fan control will not work and the fan you installed will always run at full speed.
2.2.9 1. Internal connectors Intel® X79 Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_1/2 [gray]) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. • These connectors are set to [IDE Mode] by default. If you intend to create a Serial ATA RAID set using these connectors, set the SATA Mode item in the BIOS to [RAID Mode]. Refer to section 3.5.4 SATA Configuration for details. • Before creating a RAID set, refer to section 4.
2. Intel® X79 Serial ATA 3.0 Gb/s connectors (7-pin SATA3G_3–6 [blue]) These connectors connect to Serial ATA 3.0 Gb/s hard disk drives and optical disc drives via Serial ATA 3.0 Gb/s signal cables. If you installed Serial ATA hard disk drives, you can create a RAID 0, 1, 5, and 10 configuration with the Intel® Rapid Storage Technology through the onboard Intel® X79 chipset. • These connectors are set to [IDE Mode] by default.
3. Marvell® Serial ATA 6.0 Gb/s connectors (7-pin SATA6G_E1/E2/E3/E4 [gray]) These connectors connect to Serial ATA 6.0 Gb/s hard disk drives via Serial ATA 6.0 Gb/s signal cables. 2-28 • For high performance of ASUS SSD Caching II, please connect one HDD and one SSD to Marvell® SATA6G_E12/E34 connectors. • For regular usage, the SATA6G_E12/E34 connectors are recommended for data drivers. • You must install Windows® XP Service Pack 3 or later versions before using Serial ATA hard disk drives.
4. USB 3.0 connector (20-1 pin USB3_34) This connector is for the additional USB 3.0 ports, and complies with the USB 3.0 specificaton that supports up to 5.0 Gbps connection speed. If the USB 3.0 front panel cable is available from your system chassis, with this USB 3.0 connector, you can have a front panel USB 3.0 solution. You can connect the ASUS front panel USB 3.0 box to this connector to obtain the front panel USB 3.0 solution.
5. USB 2.0 connectors (Type A: USB13; 10-1 pin USB1112; USB13) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed. Never connect a 1394 cable to the USB connectors.
6. IEEE 1394a port connector (10-1 pin IE1394_1) This connector is for an IEEE 1394a port. Connect the IEEE 1394a module cable to this connector, then install the module to a slot opening at the back of the system chassis. Never connect a USB cable to the IEEE 1394a connector. Doing so will damage the motherboard! The IEEE 1394a module is purchased separately. 7. Digital audio connector (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s).
8. CPU, CPU OPT, Chassis fan connectors (4-pin CPU_FAN; 4-pin CPU_OPT; 4-pin CHA_FAN1/2/3/4) Connect the fan cables to the fan connectors on the motherboard, ensuring that the black wire of each cable matches the ground pin of the connector. Do not forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components.
9. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. • We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
10. Serial port connector (10-1 pin COM1) This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis. The COM module is purchased separately. 11. TPM connector (20-1 pin TPM) This connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data.
12. ATX power connectors (24-pin EATXPWR; 8-pin EATX12V, 6-pin EATX12V_1) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. • For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version) and provides a minimum power of 350 W.
13. System panel connector (20-8 pin PANEL) This connector supports several chassis-mounted functions. • • • • • 2-36 System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. Hard disk drive activity LED (2-pin IDE_LED) This 2-pin connector is for the HDD Activity LED.
2.3 Building your computer system 2.3.1 Additional tools and components to build a PC system 1 bag of screws Philips (cross) screwdriver PC chassis Power supply unit Intel LGA 2011 CPU Intel LGA 2011 compatible CPU Fan DIMM SATA hard disk drive SATA optical disc drive (optional) Graphics card The tools and components in the table above are not included in the motherboard package.
2.3.2 CPU installation Please note the order in opening/ closing the double latch. Follow the instructions printed on the metal sealing hatch or the illustrations shown below in this manual. The plastic cap will pop up automatically once the CPU is in place and the hatch properly sealed down.
5 6 Triangle mark 7 8 B A 9 A B ASUS P9X79-E WS 2-39
2.3.3 CPU heatsink and fan assembly installation Apply the Thermal Interface Material to the CPU heatsink and CPU before you install the heatsink and fan if necessary.
2.3.
2.3.5 Motherboard installation The diagrams in this section are for reference only. The motherboard layout may vary with models, but the installation steps remain the same.
3 DO NOT overtighten the screws! Doing so can damage the motherboard.
2.3.
2.3.
2.3.8 Front I/O Connector To install ASUS Q-Connector 1 2 IDE_LED IDE_LED+ IDE_LED- PWR Ground Reset Ground R POWE SW RESET SW To install USB Connector To install front panel audio connector AAFP USB The actual location may vary with motherboards.
2.3.9 Rear panel connection Rear panel connectors 1. PS/2 mouse and keyboard port 7. USB BIOS Flashback button 2. LAN (RJ-45) port 1* 8. Optical S/PDIF Out port 3. USB 3.0 ports 1 and 2 9. USB 2.0 ports 7 and 8 4. LAN (RJ-45) port 2** 10. External SATA 6.0 Gb/s ports 1 and 2 5. USB 2.0 ports 1 and 2 11. USB 2.0 ports 9 and 10 6. USB 2.0 ports 3, 4, 5, and 6 12. Audio I/O ports** *and **: Refer to the tables on the next page for LAN port and audio port definitions.
• Due to USB 3.0 controller limitation, USB 3.0 devices can only be used under Windows® OS environment and after the USB 3.0 driver installation. • USB 3.0 devices can only be used as data storage only. • We strongly recommend that you connect USB 3.0 devices to USB 3.0 ports for faster and better performance for your USB 3.0 devices.
Connect to Stereo Speakers Connect to 2.1 channel Speakers Connect to 4.
Connect to 5.1 channel Speakers Connect to 7.
2.3.11 USB BIOS Flashback 1. Download the BIOS Flashback program file from the ASUS service website (www.asus. com). Save the program file to a USB portable disk. 2. On the rear I/O port, plug the USB disk to USB port 1 with the WHITE interior. (See red box in the image below) 3. Press the BIOS Flashback button for 3 seconds, and the light will begin to flash (on the third second). 4. The Flashback function is enabled once the light starts to flash. 5.
2.4 Starting up for the first time 1. After making all the connections, replace the system case cover. 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4. Connect the power cord to a power outlet that is equipped with a surge protector. 5. Turn on the devices in the following order: 6. a. Monitor b. External SCSI devices (starting with the last device on the chain) c.
Chapter 3: BIOS setup
Chapter summary 3 This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided. This chapter contains the following sections: 3.1 Knowing BIOS............................................................................................. 3-3 3.2 BIOS setup program................................................................................... 3-3 3.4 Ai Tweaker menu...................................................
3.1 Knowing BIOS The new ASUS UEFI BIOS is an Extensible Firmware Interface that complies with UEFI architecture, offering a user-friendly interface that goes beyond traditional keyboard-only BIOS controls to enable more flexible and convenient mouse input. Users can easily navigate the new UEFI BIOS with the same smoothness as their operating system. The term “BIOS” in this user manual refers to “UEFI BIOS” unless otherwise specified.
3.2.1 EZ Mode By default, the EZ Mode screen appears when you enter the BIOS setup program. The EZ Mode provides you an overview of the basic system information, and allows you to select the display language, system performance mode and boot device priority. To access the Advanced Mode, click Exit/Advanced Mode, then select Advanced Mode. The default screen for entering the BIOS setup program can be changed. Refer to the Setup Mode item in section 3.7 Boot memu for details.
3.2.2 Advanced Mode The Advanced Mode provides advanced options for experienced end-users to configure the BIOS settings. The figure below shows an example of the Advanced Mode. Refer to the following sections for the detailed configurations. To access the EZ Mode, click Exit, then select ASUS EZ Mode.
Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting Main shows the Main menu items. The other items (Ai Tweaker, Advanced, Monitor, Boot, Tool, and Exit) on the menu bar have their respective menu items. Back button This button appears when entering a submenu. Press or use the USB mouse to click this button to return to the previous menu screen.
3.3 Main menu The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program. The Main menu provides you an overview of the basic system information, and allows you to set the system date, time, language, and security settings. Security The Security menu items allow you to change the system security settings. • If you have forgotten your BIOS password, erase the CMOS Real Time Clock (RTC) RAM to clear the BIOS password. See section 2.2.
Administrator Password If you have set an administrator password, we recommend that you enter the administrator password for accessing the system. Otherwise, you might be able to see or change only selected fields in the BIOS setup program. To set an administrator password: 1. Select the Administrator Password item and press . 2. From the Create New Password box, key in a password, then press . 3. Confirm the password when prompted. To change an administrator password: 1.
3.4 Ai Tweaker menu The Ai Tweaker menu items allow you to configure overclocking-related items. Be cautious when changing the settings of the Ai Tweaker menu items. Incorrect field values can cause the system to malfunction. The configuration options for this section vary depending on the CPU and DIMM model you installed on the motherboard.
Scroll down to display the following items: Ai Overclock Tuner [Auto] Allows you to select the CPU overclocking options to achieve the desired CPU internal frequency. Select any of these preset overclocking configuration options: [Auto] Loads the optimal settings for the system. [X.M.P.] If you install memory modules supporting the eXtreme Memory Profile (X.M.P.) Technology, choose this item to set the profiles supported by your memory modules for optimizing the system performance.
Turbo Ratio [Auto] Allows you to manually adjust the Turbo CPU ratio. [Auto] All Turbo ratio are set by Intel CPU default settings [By Per Core (Cannot Adjust in OS)] All numbers of active cores can be set to an individual Turbo ratio in BIOS. [By ALL Cores (Can Adjust in OS)] All numbers of active cores will be set to one single Turbo ratio in OS CPU CLOCKGEN FILTER [Auto] May help maximize CPU Overclocking when Enabled.
Primary Timings DRAM CAS# Latency [Auto] Use the <+> and <-> keys to adjust the value. The values range from 3 to 15 with 1 interval. DRAM RAS# to CAS# Delay [Auto] Use the <+> and <-> keys to adjust the value. The values range from 4 to 15 with 1 interval. DRAM RAS# PRE Time [Auto] Use the <+> and <-> keys to adjust the value. The values range from 4 to 15 with 1 interval. DRAM RAS# ACT Time [Auto] Use the <+> and <-> keys to adjust the value. The values range from 4 to 40 with 1 interval.
tRWDD [Auto] Use the <+> and <-> keys to adjust the value. The values range from 0 to 15 with 1 interval. tWRDR [Auto] Use the <+> and <-> keys to adjust the value. The values range from 0 to 7 with 1 interval. tWRDD [Auto] Use the <+> and <-> keys to adjust the value. The values range from 0 to 7 with 1 interval. tRWSR [Auto] Use the <+> and <-> keys to adjust the value. The values range from 0 to 15 with 1 interval. tCCD [Auto] Use the <+> and <-> keys to adjust the value.
DRAM IOL (CHA D1 R1) [Auto] Configuration options: [Auto] [Advance 14 Clock] – [Advance 1 Clock] [Normal] [Delay 1 Clock] – [Delay 14 Clock] DRAM RTL (CHB D0 R0) [Auto] Configuration options: [Auto] [Advance 14 Clock] [Advance 12 Clock] [Advance 10 Clock] [Advance 8 Clock] [Advance 6 Clock] [Advance 4 Clock] [Advance 2 Clock] [Normal] [Delay 2 Clock] [Delay 4 Clock] [Delay 6 Clock] [Delay 8 Clock] [Delay 10 Clock] [Delay 12 Clock] [Delay 14 Clock] DRAM IOL (CHB D0 R0) [Auto] Configuration options: [Auto]
DRAM IOL (CHC D0 R0) [Auto] Configuration options: [Auto] [Advance 14 Clock] – [Advance 1 Clock] [Normal] [Delay 1 Clock] – [Delay 14 Clock] DRAM RTL (CHC D0 R1) [Auto] Configuration options: [Auto] [Advance 14 Clock] [Advance 12 Clock] [Advance 10 Clock] [Advance 8 Clock] [Advance 6 Clock] [Advance 4 Clock] [Advance 2 Clock] [Normal] [Delay 2 Clock] [Delay 4 Clock] [Delay 6 Clock] [Delay 8 Clock] [Delay 10 Clock] [Delay 12 Clock] [Delay 14 Clock] DRAM IOL (CHC D0 R1) [Auto] Configuration options: [Auto]
DRAM IOL (CHD D0 R1) [Auto] Configuration options: [Auto] [Advance 14 Clock] – [Advance 1 Clock] [Normal] [Delay 1 Clock] – [Delay 14 Clock] DRAM RTL (CHD D1 R0) [Auto] Configuration options: [Auto] [Advance 14 Clock] [Advance 12 Clock] [Advance 10 Clock] [Advance 8 Clock] [Advance 6 Clock] [Advance 4 Clock] [Advance 2 Clock] [Normal] [Delay 2 Clock] [Delay 4 Clock] [Delay 6 Clock] [Delay 8 Clock] [Delay 10 Clock] [Delay 12 Clock] [Delay 14 Clock] DRAM IOL (CHD D1 R0) [Auto] Configuration options: [Auto]
Transmitter Slew [Auto] Configuration options: [Auto] [Normal] [More] MCH Recheck [Auto] Configuration options: [Auto] [Disabled] [Enabled] MRC Fast Warm Boot [Auto] Configuration options: [Auto] [Disabled] DIGI+ Power Control CPU Load-Line Calibration [Auto] CPU Load-line is defined by Intel spec and affects CPU voltage. The CPU working voltage will decrease proportionally to CPU loading. Higher value could get higher voltage and good overclocking performance, but increase the CPU thermal.
VCCSA Current Capability [100%] Allows you to set the VCCSA current capability. A higher value brings wider total DRAM controller power range and extends the overclocking frequency range simultaneously. Configuration options: [100%] [110%] [120%] [130%] CPU VCCSA Boot Up Voltage [Auto] This adjusts the voltage for VCCSA at initial boot up. Set to higher values for better overclocking results. Use the <+> and <-> keys to adjust the value. The values range from 0.800 to 1.700 with 0.005 interval.
Manual Adjustment [Medium] This item appears when you set the CPU Power Phase Control item to [Manual Adjustment]. Select Ultra Fast for a faster response. The reaction time will be longer when Regular is selected. Configuration options: [Ultra Fast] [Fast] [Medium] [Regular] Do not remove the thermal module when switching to Extreme and Manual mode. The thermal conditions should be monitored.
CPU Performance Settings The items in this menu is setting for CPU Ratio/Features. CPU Ratio [Auto] This item allows user manually adjust the maximum non-turbo CPU ratio. The value will be limited to CPU-based or factory settings. Adjusting the CPU Ratio value will change CPU Performance Settings. Use the <+> and <-> keys to adjust the value. The values range from 12 to 57 with 1 interval.
CPU VCORE Voltage [Offset Mode] This adjusts the power supply for the processor cores and cache to help core frequency overclocking. [Manual Mode] Allows you to set a fixed CPU VCORE voltage. [Offset Mode] Allows you to set the Offset voltage. CPU VCORE Manual Voltage [Auto] This item appears only when you set the CPU VCORE Voltage item to [Manual Mode] and allows you to set a fixed CPU VCORE voltage. The values range from 0.800V to 1.700V with a 0.005V interval.
DRAM Voltage (CHA, CHB) [Auto] Allows you to set the DRAM voltage. The values range from 1.20V to 1.99V with a 0.005V interval. DRAM Voltage (CHC, CHD) [Auto] Allows you to set the DRAM voltage. The values range from 1.20V to 1.99V with a 0.005V interval. According to Intel CPU spec, DIMMs with voltage requirement over 1.65V may damage the CPU permanently. We recommend you install the DIMMs with the voltage requirement below 1.65V. CPU PLL Voltage [Auto] Allows you to set the CPU and PCH PLL voltage.
DRAM CTRL REF Voltage on CHB [Auto] Allows you to set the DRAM CTRL REF Voltage on Channel B. The values range from 0.3950x to 0.6300x with a 0.005x interval. DRAM DATA REF Voltage on CHB [Auto] Allows you to set the DRAM DATA REF Voltage on Channel B. The values range from 0.3950x to 0.6300x with a 0.005x interval. DRAM CTRL REF Voltage on CHC [Auto] Allows you to set the DRAM CTRL REF Voltage on Channel C. The values range from 0.3950x to 0.6300x with a 0.005x interval.
3.5 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Be cautious when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction.
3.5.1 CPU Configuration The items in this menu show the CPU-related information that the BIOS automatically detects. The items shown in this screen may be different due to the CPU you installed. Scroll down to display the following items: Intel Adaptive Thermal Monitor [Enabled] This function includes TM1, TM2, and EMTTM. [Disabled] Disables the CPU thermal monitor function. [Enabled] Enables the overheated CPU to throttle its clock speed to cool down.
Active Processor Cores [All] Allows you to choose the number of CPU cores to activate in each processor package. Configuration options: [All] [1] [2] [3] [4] [5] Limit CPUID Maximum [Disabled] [Enabled] [Disabled] Allows legacy operating systems to boot even without support for CPUs with extended CPUID functions. Disables this function (for Windows XP). [Enabled] [Disabled] Enables the No-Execution Page Protection Technology. Forces the XD feature flag to always return to zero (0).
CPU C3 Report [Auto] Allows you to disable or enable the CPU C3 report to OS. CPU C6 Report [Auto] Allows you to disable or enable the CPU C6 report to OS. CPU C7 Report [Auto] Allows you to disable or enable the CPU C7 report to OS. 3.5.2 System Agent Configuration Intel (R) VT-d [Disabled] Allows you to enable virtualization technology function on memory control hub. [Enabled] Enables the function. [Disabled] Disables this function.
3.5.3 PCH Configuration High Precision Timer [Enabled] Allows you to enable or disable the High Precision Event Timer. Configuration options: [Disabled] [Enabled] 3.5.4 SATA Configuration While entering Setup, the BIOS automatically detects the presence of SATA devices. The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port.
SATA Mode [AHCI Mode] Allows you to set the SATA configuration. [Disabled] [IDE Mode] [AHCI Mode] [RAID Mode] Disables the SATA function. Set to [IDE Mode] when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices. Hotplug support configurations for SATA are disallowed under this mode. Set to [AHCI Mode] when you want the SATA hard disk drives to use the AHCI (Advanced Host Controller Interface).
SATA6G_5 (Blue) Hot Plug [Disabled] This item appears only when you set the previous item to [AHCI Mode] and [RAID mode]. It allows users to enable/disable SATA Hot Plug Support. Configuration options: [Disabled] [Enabled]. SATA6G_6 (Blue) Hot Plug [Disabled] This item appear only when you set the previous item to [AHCI Mode]. It’s allow user to enabled/disabled SATA Hot Plug Support. Configuration options: [Disabled] [Enabled].
The USB Devices item shows the auto-detected values. If no USB device is detected, the item shows None. Legacy USB Support [Enabled] •[Disabled] •[Enabled] •[Auto] The USB devices can be used only for the BIOS setup program. Enables the support for USB devices on legacy operating systems (OS). Allows the system to detect the presence of USB devices at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled. Legacy USB3.
3.5.6 Onboard Devices Configuraton Scroll down to display the following items: Azalia HD Audio [Enabled] •[Disabled] •[Enabled] Disables the controller. Enables the High Definition Audio Controller. The following two items appear only when you set the HD Audio Controller item to [Enabled]. Front Panel Type [HD] Allows you to set the front panel audio connector (AAFP) mode to legacy AC97 or highdefinition audio depending on the audio standard that the front panel audio module supports.
Intel LAN1 Controller [Enabled] •[Disabled] •[Enabled] Disables the controller. Enables the Intel LAN controller. Intel LAN1 OPROM [Disabled] This item appears only when you set the previous item to [Enabled] and allows you to enable or disable the LAN1 PXE OptionRom of the Intel LAN controller. Configuration options: [Disabled] [Enabled] Intel LAN2 Controller [Enabled] •[Disabled] •[Enabled] Disables the controller. Enables the Intel LAN controller.
3.5.7 APM Restore AC Power Loss [Power Off] [Power On] [Power Off] [Last State] The system goes into on state after an AC power loss. The system goes into off state after an AC power loss. The system goes into either off or on state, whatever the system state was before the AC power loss. Power On By PS/2 Keyboard [Disabled] [Disabled] [Space Bar] [Ctrl-Esc] [Power Key] Disables the Power On by a PS/2 keyboard. Sets the Space Bar on the PS/2 keyboard to turn on the system.
3.6 Monitor menu The Monitor menu displays the system temperature/power status, and allows you to change the fan settings. Scroll down to display the following items: CPU Temperature / MB Temperature [xxxºC/xxxºF] The onboard hardware monitor automatically detects and displays the CPU and motherboard temperatures. Select Ignore if you do not wish to display the detected temperatures.
CPU Fan Speed [xxxx RPM] or [Ignore] / [N/A] CPU OPT Speed [xxxx RPM] or [Ignore] / [N/A] Chassis Fan 1/2/3/4 Speed [xxxx RPM] or [Ignore] / [N/A] The onboard hardware monitor automatically detects and displays the CPU, CPU OPT, and chassis fan speed in rotations per minute (RPM). If the fan is not connected to the motherboard, the field shows N/A. Select Ignore if you do not wish to display the detected speed. CPU Q-Fan Control [Enabled] •[Disabled] •[Enabled] Disables the CPU Q-Fan control feature.
Chassis 1/2/3/4 Q-Fan Control [Enabled] •[Disabled] •[Enabled] Disables the Chassis Q-Fan control feature. Enables the Chassis Q-Fan control feature. Chassis 1/2/3/4 Fan Speed Low Limit [600 RPM] This item appears only when you enable the Chassis 1/2/3/4 Q-Fan Control feature and allows you to disable or set the chassis fan warning speed in case the fan stops working.
3.7 Boot menu The Boot menu items allow you to change the system boot options. Boot Configuration Fast Boot [Enabled] [Enabled] Select to accelerate the boot speed. [Disabled] Select to go back to normal boot. The following four items appear when you set Fast Boot to [Enabled]. USB Support [Partial Initialization] [Disabled] [Full Initialization] [Partial Initialization] 3-38 All USB devices will not be available until OS boot up for the fastest POST time.
PS/2 Keyboard and Mouse Support [Auto] Select any of these settings when PS/2 keyboard and mouse are installed. These settings only apply when Fast Boot is enabled. [Auto] For a faster POST time, PS/2 devices will only be available when the system boots up or rebooted when the PS/2 devices have not been reconnected or changed. If you disconnect or change PS/2 devices before restarting the system, PS/2 devices will not be available and BIOS setup program will not be accessible via PS/2 devices.
Setup Mode [EZ Mode] [Advanced Mode] Sets Advanced Mode as the default screen for entering the BIOS setup program. [EZ Mode] Sets EZ Mode as the default screen for entering the BIOS setup program. CSM (Compatibility Support Module) Allows you to configure the CSM (Compatibility Support Module) items to fully support the various VGA, bootable devices and add-on devices for better compatibility.
Key Management This item appears only when you set Secure Boot Mode to [Custom]. It allows you to manage the Secure Boot keys. Install Default Secure Boot keys Allows you to immediately load the default Security Boot keys, Platform key (PK), Key-exchange Key (KEK), Signature database (db), and Revoked Signatures (dbx). When the default Secure boot keys are loaded, the PK state will change from Unloaded mode to loaded mode.
3.8 Tools menu The Tools menu items allow you to configure options for special functions. Select an item then press to display the submenu. 3.8.1 ASUS EZ Flash 2 Utility Allows you to run ASUS EZ Flash 2 Utility to update BIOS. When you press , a confirmation message appears. Use the left/right arrow key to select between [Yes] or [No], then press to confirm your choice. For more details, refer to section 3.10.2 ASUS EZ Flash 2 utility. 3.8.
3.8.3 ASUS O.C. Profile This item allows you to store or load multiple BIOS settings. The Setup Profile Status items will show Not Installed if no profile is created. Label Allows you to input the label of setup profile. Save to Profile Allows you to save the current BIOS settings to the BIOS Flash, and create a profile. Key in a profile number from one to eight, or use <+> and <-> keys to adjust the number. Press , and then select Yes.
3.9 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items, and save or discard your changes to the BIOS items. You can access the EZ Mode from the Exit menu. Exit Load Optimized Defaults Save Changes & Reset Discard Changes & Exit ASUS EZ Mode Launch EFI Shell from filesystem device Load Optimized Defaults This option allows you to load the default values for each of the parameters on the Setup menus.
3.10 Updating BIOS The ASUS website publishes the latest BIOS versions to provide enhancements on system stability, compatibility, or performance. However, BIOS updating is potentially risky. If there is no problem using the current version of BIOS, DO NOT manually update the BIOS. Inappropriate BIOS updating may result in the system’s failure to boot. Carefully follow the instructions of this chapter to update your BIOS if necessary. Visit the ASUS website (www.asus.
Updating the BIOS through the Internet To update the BIOS through the Internet: 1. From the ASUS Update screen, select Update BIOS from Internet, and then click Next. 2. Select the ASUS FTP site nearest you to avoid network traffic. If you want to enable the BIOS downgradable function and auto BIOS backup function, check the checkboxs before the two items on the screen. 3-46 3. Select the BIOS version that you want to download. Click Next. 4.
Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: 1. From the ASUS Update screen, select Update BIOS from file, and then click Next. 2. Locate the BIOS file from the Open window, click Open, and click Next. 3. You can decide whether to change the BIOS boot logo. Click Yes if you want to change the boot logo or No to continue. 4. Follow the onscreen instructions to complete the update process. • The screenshots in this section are for reference only.
3.10.2 ASUS EZ Flash 2 utility The ASUS EZ Flash 2 feature allows you to update the BIOS without having to use a bootable floppy disk or an OS‑based utility. Before you start using this utility, download the latest BIOS from the ASUS website at www.asus.com. To update the BIOS using EZ Flash 2: 3-48 1. Insert the USB flash disk that contains the latest BIOS file to the USB port. 2. Enter the Advanced Mode of the BIOS setup program.
• This function can support devices such as a USB flash disk with FAT 32/16 format and single partition only. • DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure! Ensure to load the BIOS default settings to ensure system compatibility and stability. Select the Load Optimized Defaults item under the Exit menu. See section 3.9 Exit Menu for details. 3.10.
3.10.4 ASUS BIOS Updater The ASUS BIOS Updater allows you to update BIOS in DOS environment. This utility also allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or gets corrupted during the updating process. The succeeding utility screens are for reference only. The actual utility screen displays may not be same as shown. Before updating BIOS 1. Prepare the motherboard support DVD and a USB flash drive in FAT32/16 format and single partition. 2.
Backing up the current BIOS To backup the current BIOS file using the BIOS Updater Ensure that the USB flash drive is not write-protected and has enough free space to save the file. 1. At the FreeDOS prompt, type bupdater /o[filename] and press . D:\>bupdater /oOLDBIOS1.cap Filename Extension The [filename] is any user-assigned filename with no more than eight alphanumeric characters for the filename and three alphanumeric characters for the extension. 2.
Updating the BIOS file To update the BIOS file using BIOS Updater 1. At the FreeDOS prompt, type bupdater /pc /g and press . D:\>bupdater /pc /g 2. The BIOS Updater screen appears as below. ASUSTek BIOS Updater for DOS V1.18 [2011/04/29] Current CAP BOARD: P9X79-E WS VER: 0220 DATE: 08/09/2011 Update CAP BOARD: Unknown VER: Unknown DATE: Unknown PATH: A:\ P8P67D.
Chapter 4: Software support
Chapter summary 4 This chapter describes the contents of the support DVD that comes with the motherboard package and the software. This chapter contains the following sections: 4.1 Installing an operating system.................................................................. 4-3 4.2 Support DVD information........................................................................... 4-3 4.4 RAID configurations................................................................................. 4-25 4.
4.1 Installing an operating system This motherboard supports Windows® 8 / 64-bit 8 / 7 / 64-bit 7 operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your hardware. 4.2 • Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Refer to your OS documentation for detailed information.
4.2.2 Obtaining the software manuals The software manuals are included in the support DVD. Follow the instructions below to get the necessary software manuals. The software manual files are in Portable Document Format (PDF). Install the Adobe® Acrobat® Reader from the Utilities menu before opening the files. 1. Click on the Manual tab. Click on ASUS Motherboard Utility Guide from the manual list on the left. 2. The Manual folder of the support DVD appears.
4.3 Software information Most of the applications in the support DVD have wizards that will conveniently guide you through the installation. View the online help or readme file that came with the software application for more information. 4.3.1 ASUS AI Suite II AI Suite II is an all-in-one interface that integrates several ASUS utilities and allows users to launch and operate these utilities simultaneously. Installing ASUS AI Suite II To install ASUS AI Suite II on your computer 1.
4.3.2 ASUS SSD Caching II ASUS SSD Caching II uses installed SSDs for multi-caching of frequently accessed data or applications. It combines multiple SSDs’ performance and hard-drive capacity to boost the system’s overall performance. Launching ASUS SSD Caching II To launch ASUS SSD Caching, click Tool > ASUS SSD Caching II on the AI Suite II main menu bar.
3. To cancel caching, click . • During initialization, you can proceed with doing any system operations. You can check the caching status later or wait for a pop-up message notifying that initialization is completed. • For regular usage, the SATA6G_E12/E34 connectors are recommended for data drives. • After disabling SSD Caching, the SSD will become a non-configurable disk in Windows OS. To use the SSD again for normal functions, go to Disk Management to reconfigure the SSD.
4.3.3 Ai Charger+ This utility allows you to fast-charge your portable BC 1.1* mobile devices on your computer’s USB port three times faster than the standard USB devices**. 4-8 • * Check your manufacturer if your USB device is a Battery Charging Specification 1.1 (BC 1.1) compliant or compatible device. • ** Actual charging speeds may vary depending on the charging rate and specifications of your USB device.
4.3.4 ASUS Update ASUS Update lays out the options for updating BIOS on your system. Update BIOS utility on your system or simply save the utility for later use just by following the directions on this convenient updating feature. Launching ASUS Update After installing AI Suite II from the motherboard support DVD, launch ASUS Update by clicking Update> ASUS Update on the AI Suite II main menu bar. Using ASUS Update Select the way you would like to do with the BIOS utility.
4.3.5 DIGI+ Power Control DIGI+ PowerControl allows you to adjust VRM voltage and frequency modulation to enhance reliability and stability. It also provides the highest power efficiency, generating less heat to longer component lifespan and minimize power loss. After installing AI Suite II from the motherboard support DVD, launch DIGI+ Power Control by clicking Tool > DIGI+ Power Control on the AI Suite II main menu bar. Select CPU Power or DRAM Power to adjust the power control settings.
DRAM Power 1 Application aids 2 3 Apply all changes immediately Undo all changes without applying Function no. Function description 1 DRAM Current Capability A higher value brings a wider total power range and extends the overclocking frequency range simultaneously. 2 DRAM Voltage Frequency Allows you to adjust the DRAM switching frequency for system stability or to increase OC Range.
4.3.6 EPU EPU is an energy-efficient tool that satisfies different computing needs. This utility provides several modes that you can select to save system power. Selecting Auto mode will have the system shift modes automatically according to current system status. You can also customize each mode by configuring settings like CPU frequency, GPU frequency, vCore Voltage, and Fan Control.
4.3.7 FAN Xpert+ FAN Xpert+ intelligently allows you to adjust both the CPU and chassis fan speeds according to different ambient temperatures caused by different climate conditions in different geographic regions and your PC’s system loading. The built-in variety of useful profiles offer flexible automatic and manual fan speed controls to achieve a quiet and cool environment.
4.3.8 MyLogo2 This MyLogo utility lets you customize the boot logo. The boot logo is the image that appears on screen during the Power‑On‑Self-Tests (POST). Personalize your computer from the very beginning! Launching ASUS Update After installing AI Suite II from the motherboard support DVD, launch MyLogo by clicking Update> MyLogo on the AI Suite II main menu bar. Using MyLogo Select the way you would like to do update your boot logo. Then click Next and follow the given instructions.
2. Click on Auto Tune to adjust image size compatibility or adjust the resolution bar. 3. You can click on Booting Preview to preview the boot image. Then click Next. 4. Click on Flash to start updating the image to the boot logo. 5. Click on Yes to reboot or you can also see the new logo next time you restart your computer. Change the boot logo of a downloaded BIOS file and update (or do not update) this BIOS to the motherboard 1.
4.3.9 Probe II Probe II is a utility that monitors the computer’s vital components, and detects and alerts you of any problem with these components. Probe II senses fan rotations, CPU temperature, and system voltages, among others. With this utility, you are assured that your computer is always at a healthy operating condition. Launching Probe II After installing AI Suite II from the motherboard support DVD, launch Probe II by clicking Tool > Probe II on the AI Suite II main menu bar.
4.3.10 TurboV EVO ASUS TurboV EVO introduces TurboV that allows you to manually adjust the CPU frequency and related voltages as well as Auto Tuning function that offers automatic and easy overclocking and system level up. After installing AI Suite II from the motherboard support DVD, launch TurboV EVO by clicking Tool > TurboV EVO on the AI Suite II main menu bar. Refer to the software manual in the support DVD or visit the ASUS website at www.asus.com for detailed software configuration.
Using Advanced Mode Click on the Advanced Mode tab to adjust the advanced voltage settings. Advanced mode Target values Voltage Adjustment bars Undoes all changes without applying Current values Click to restore all start-up settings Applies all changes immediately CPU Ratio Allows you to manually adjust the CPU ratio. The first time you use CPU Ratio, go to AI Tweaker > CPU Power Management in BIOS and set the Turbo Ratio item to [Maximum Turbo Ratio setting in OS]. 1. Click on the CPU Ratio tab.
CPU Strap Allows you to manually adjust CPU Strap. 1. Click on the CPU Strap tab. 2. Click on the adjustment bar to the desired value. The graph on the right will change value accordingly. 3. Click on Apply to make the change take effect. CPU Strap Adjustment bar Undoes all changes without applying Click to restore all start-up settings • Applies all changes immediately Every CPU Strap support is subject to the physical characteristics of individual CPUs.
3. TurboV automatically overclocks the CPU, saves BIOS settings and restarts the system. After re-entering Windows, a message appears indicating auto tuning success. Click OK to exit. Using Extreme Tuning 1. 4-20 Click the Auto Tuning tab and then click Extreme. 2. Read through the warning messages and click OK to start auto-overclocking. 3. TurboV automatically overclocks the CPU and memory and restarts the system.
4.3.11 USB 3.0 Boost The ASUS exclusive USB 3.0 Boost provides speed boost for USB 3.0 devices and the up-to-date support of USB Attached SCSI Protocol (UASP). With USB 3.0 Boost, you can accelerate the transfer speed of your USB 3.0 devices with ease. Launching USB 3.0 Boost After installing AI Suite II from the motherboard support DVD, launch USB 3.0 Boost by clicking Tool > USB 3.0 Boost on the AI Suite II main menu bar. Configuring USB 3.0 Boost 1. Connect a USB 3.0 device to the USB 3.0 port. 2.
4.3.12 Audio configurations The Realtek audio CODEC provides 8-channel audio capability to deliver the ultimate audio experience on your computer. The software provides Jack-Sensing function, S/PDIF Out support, and interrupt capability. The CODEC also includes the Realtek® proprietary UAJ® (Universal Audio Jack) technology for all audio ports, eliminating cable connection errors and giving users plug and play convenience.
4.3.13 ASUS Dr. Power Utility ASUS Dr. Power is a monitoring utility that provides notifications when the power supply is unable to provide sufficient power to the system. You can choose to allow continuous notifications or stop messages from appearing until the next time you reboot your computer. The utility is used to monitor changes in the power supplied to the system that may affect performance and system stability. ASUS Dr. Power Utility runs on your system only when the Dr. Power switch is enabled.
When ASUS Dr. Power detects that your system is running low on power, an event notification pops up to indicate that your power supply requires attention. The message will be displayed for 15 seconds or until you click the Close button. ASUS Dr. Power will notify you of the power status if the same conditions are present on your system. ASUS Dr. Power can be configured to provide notifications at regular intervals: 4-24 • 15 minutes - Messages will be displayed every 15 minutes.
4.4 RAID configurations The motherboard supports the following SATA RAID solutions: • Intel® Rapid Storage Technology with RAID 0, RAID 1, RAID 10 and RAID 5 support. • Mavell® RAID utility with RAID 0 and RAID 1 support. 4.4.1 • You must install Windows® XP Service Pack 3 or later versions before using Serial ATA hard disk drives. The Serial ATA RAID feature is available only if you are using Windows® XP SP3 or later versions.
4.4.2 Installing Serial ATA hard disks The motherboard supports Serial ATA hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array. To install the SATA hard disks for a RAID configuration: 1. Install the SATA hard disks into the drive bays. 2. Connect the SATA signal cables. 3. Connect a SATA power cable to the power connector on each drive. 4.4.
The navigation keys at the bottom of the screen allow you to move through the menus and select the menu options. The RAID BIOS setup screens shown in this section are for reference only and may not exactly match the items on your screen. The utility supports maximum four hard disk drives for RAID configuration. Creating a RAID set To create a RAID set: 1. From the utility main menu, select 1. Create RAID Volume and press .
5. Use the up/down arrow key to select a drive, and then press to select. A small triangle marks the selected drive. Press after completing your selection. 6. Use the up/down arrow key to select the stripe size for the RAID array (for RAID 0, 10 and 5 only),and then press . The available stripe size values range from 4KB to 128KB.
Deleting a RAID set Take caution when deleting a RAID set. You will lose all data on the hard disk drives when you delete a RAID set. To delete a RAID set: 1. From the utility main menu, select 2. Delete RAID Volume and press . The following screen appears: Intel(R) Rapid Storage Technology - Option ROM - v10.0.0.1032 Copyright(C) 2003-10 Intel Corporation. All Rights Reserved.
4.4.5 Marvell RAID utility The onboard Marvell SATA 6.0 Gb/s controller allows you to create a RAID 0 or RAID 1 array using two SATA hard disk drives. Refer to Chapter 2 of your motherboard user manual for the exact location of the Marvell SATA 6.0 Gb/s connector. To enter the Marvell utility, press + during POST. All exisiting data on the hard disk drives will be erased when creating or deleting a RAID array.
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd. Configure->Select free disksCreate Virtual Disk HBA 0: Marvell 0 RAID Level : RAID 0 Max Size(MB) : 305253 ├ Virtual Disks └ Free Physical Disks Stripe Size : 64KB * ├ PD 0: ST3160812AS Quick Init : Yes * └ PD 8: ST3160812AS Name : Default Threshold(%) : 90 Next ▶ Help Virtual disk configurations. ENTER: Select F10: Exit/Save ESC: Return 4.
Marvell BIOS Setup (c) 2009 Marvell Technology Group Ltd. Topology HBA 0: Marvell 0 ├ Virtual Disks │ └ VD 0: New_VD │ ├ PD 0: ST3160812AS │ └ PD 8: ST3160812AS └ Free Physical Disks Information Vendor ID : 1B4B Device ID : 9130 Revision ID : B1 BIOS Version : 1.0.0.1028 Firmware Version: 2.2.0.1105 PCIe Speed Rate : 5.0Gbps Configure SATA as: AHCI Mode ▶ Help Marvell RAID on chip controller. ENTER: Operation F10: Exit/Save ESC: Return 6. ▶ Press .
2. The following warning message appears: Delete Virtual Disk Do you want to delete this virtual disk ? Yes No Press to delete the selected RAID array. The following warning message appears: Delete MBR Do you want to delete MBR from this virtual disk ? Yes No Press to delete the Master Boot Record (MBR) from the selected RAID array. 3. Press .
4-34 Chapter 4: Software support
Chapter 5: Multiple GPU technology support
Chapter summary 5 This chapter describes the motherboard features and the new technologies it supports. This chapter contains the following sections: 5.1 5.2 5.3 ATI® CrossFireX™ technology................................................................... 5-3 NVIDIA® SLI™ technology.......................................................................... 5-9 NVIDIA® CUDA™ technology...................................................................
5.1 ATI® CrossFireX™ technology The motherboard supports the ATI® CrossFireX™ technology that allows you to install multigraphics processing units (GPU) graphics cards. Follow the installation procedures in this section. 5.1.1 Requirements • In CrossFireX mode, you should have two identical CrossFireX-ready graphics cards or one CrossFireX-ready dual-GPU graphics card that are ATI® certified. • Ensure that your graphics card driver supports the ATI CrossFireX technology.
5.1.3 Installing two CrossFireX™ graphics cards The following pictures are for reference only. The graphics cards and the motherboard layout may vary with models, but the installation steps remain the same. 1. Prepare two CrossFireX-ready graphics cards. 2. Insert the two graphics card into the PCIEX16 slots. If your motherboard has more than two PCIEX16 slots, refer to Chapter 1 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. 3.
5. Connect two independent auxiliary power sources from the power supply to the two graphics cards separately. 6. Connect a VGA or a DVI cable to the graphics card. 5.1.4 Installing three CrossFireX™ graphics cards 1. Prepare three CrossFireX-ready graphics cards. 2. Insert the three graphics card into the PCIEX16 slots.
5.1.5 5-6 Installing four CrossFireX™ graphics cards 1. Prepare four CrossFireX-ready graphics cards. 2. Insert the four graphics card into the PCIEX16 slots. Refer to Chapter 1 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. 3. Ensure that the cards are properly seated on the slots. 4. Align and firmly insert the four CrossFireX bridge connectors to the goldfingers on each graphics card. Ensure that the connectors are firmly in place.
5.1.6 Installing the device drivers Refer to the documentation that came with your graphics card package to install the device drivers. Ensure that your PCI Express graphics card driver supports the AMD® CrossFireX™ technology. Download the latest driver from the AMD website (www.amd.com). 5.1.7 Enabling the AMD® CrossFireX™ technology After installing your graphics cards and the device drivers, enable the CrossFireX™ feature through the AMD Catalyst™ Control Center in Windows environment.
Enabling Dual CrossFireX technology 1. In the Catalyst Control Center window, click Performance > AMD CrossFireXTM. 2. Select Enable CrossFireXTM. 3. Select a GPU combination from the drop-down list. 4. Click Apply to save and activate the GPU settings made.
5.2 NVIDIA® SLI™ technology The motherboard supports the NVIDIA® SLI™ (Scalable Link Interface) technology that allows you to install multi-graphics processing units (GPU) graphics cards. Follow the installation procedures in this section. 5.2.1 Requirements • In Dual SLI mode, you should have two identical SLI-ready graphics cards that are NVIDIA® certified. • In Triple SLI mode, you should have three identical SLI-ready graphics cards that are NVIDIA® certified.
5.2.2 Installing two SLI-ready graphics cards The following pictures are for reference only. The graphics cards and the motherboard layout may vary with models, but the installation steps remain the same. 1. Prepare two SLI-ready graphics cards. 2. Insert the two graphics card into the PCIEX16 slots. If your motherboard has more than two PCIEX16 slots, refer to Chapter 2 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. 3.
5.2.3 Installing three SLI-ready graphics cards 1. Prepare three SLI-ready graphics cards. 2. Insert the three graphics card into the PCIEX16 slots. If your motherboard has more than two PCIEX16 slots, refer to Chapter 2 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. 3. Ensure that the cards are properly seated on the slots. 4. Align and firmly insert the 3-Way SLI bridge connector to the goldfingers on each graphics card.
5.2.4 Installing four SLI-ready graphics cards 1. Prepare four SLI-ready graphics cards. 2. Insert the four graphics card into the PCIEX16 slots. If your motherboard has more than two PCIEX16 slots, refer to Chapter 2 in this user manual for the locations of the PCIEX16 slots recommended for multi-graphics card installation. 3. Ensure that the cards are properly seated on the slots. 4. Align and firmly insert the 4-Way SLI bridge connector to the goldfingers on each graphics card.
5.2.5 Enabling the NVIDIA® SLI™ technology After installing your graphics cards and the device drivers, enable the SLI feature in NVIDIA® Control Panel under the Windows® 7 operating system. Launching the NVIDIA Control Panel You can launch the NVIDIA Control Panel by the following two methods. A. Right click on the empty space of the Windows® desktop and select NVIDIA Control Panel. The NVIDIA Control Panel window appears (See Step B3). B1.
B3. The NVIDIA Control Panel window appears. Enabling SLI settings From the NVIDIA Control Panel window, select Configure SLI, Surround, PhysX. In the Quad-SLI enabled, click Maximize 3D Performance SLI to set the display for viewing SLI rendered content. When done, click Apply.
5.3 NVIDIA® CUDA™ technology The motherboard supports the NVIDIA® CUDA™ technology and up to 4 NVIDIA® Tesla™ computing processor cards(based on different type tesla cards), providing the optimum multi purpose computing performance. Follow the installation procedures in this section. 5.3.1 Requirements • 32/64-bit Microsoft® Windows XP/ Vista/ Linux RHEL5.X/ Open SuSE11.X OS • The requirements of memory and power supply vary with the Telsa cards you installed. 5.3.
2. Connect either one 8-pin power connector or two 6-pin power connectors from the power supply to the Quadro graphics card and Tesla computing processor card(s). 3. Connect a display cable to the graphics card. SLI bridge Goldfingers 4. Refer to the documentation that came with your graphics card package to install the device drivers. 5. To verify graphics card driver installation, right-click My Computer and select Properties from the menu. Click the Hardware tab, and then click Device Manager.
ASUS contact information ASUSTeK COMPUTER INC. Address Telephone Fax E-mail Web site Technical Support Telephone Online support 15 Li-Te Road, Peitou, Taipei, Taiwan 11259 +886-2-2894-3447 +886-2-2890-7798 info@asus.com.tw www.asus.com.tw +86-21-38429911 support.asus.
(510)739-3777/(510)608-4555 800 Corporate Way, Fremont, CA 94539. Asus Computer International Date : Signature : Representative Person’s Name : Mar. 01, 2013 Steve Chang / President This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.