PE100A Embedded Computer User Manual
E19619 Revised Edition V4 April 2022 COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents About this manual..............................................................................................................5 Conventions used in this manual.......................................................................................... 6 Package contents...............................................................................................................7 Chapter 1: Getting to know your Embedded Computer 1.1 Features.......................................................
3.11 Installing DIN rail clips (optional).......................................................................54 3.12 Installing the terminal block (optional)............................................................55 Chapter 4: Setting up your Embedded Computer 4.1 Requirements............................................................................................................58 4.2 Flashing the OS Image.........................................................................................
About this manual This manual provides information about the hardware and software features of your Embedded Computer, organized through the following chapters: Chapter 1: Getting to know your Embedded Computer This chapter details the hardware components of your Embedded Computer. Chapter 2: Using your Embedded Computer This chapter provides you with information on using your Embedded Computer.
Conventions used in this manual To highlight key information in this manual, some text are presented as follows: IMPORTANT! This message contains vital information that must be followed to complete a task. NOTE: This message contains additional information and tips that can help complete tasks. WARNING! This message contains important information that must be followed to keep you safe while performing certain tasks and prevent damage to your Embedded Computer's data and components.
Package contents Your Embedded Computer package contains the following items: PE100A AC power adapter* Power cord* Terminal blocks Terminal block power adapter I/O port dust covers Wall mount kit PE100A 7
Optional items Antennas DIN rail clips NOTE: • *The bundled power adapter may vary by model and territory. • Some bundled accessories may vary depending on model. For details on these accessories, refer to their respective user manuals. • The device illustration is for reference only. Actual product specifications may vary depending on model.
Getting to know your Embedded Computer 1
1.1 Features 1.1.1 Front view LTE Wireless antenna jack The LTE wireless antenna jack allows you to connect a wireless antenna for LTE signals. NOTE: The LTE wireless antenna is optional and may not come bundled. GPS Wireless antenna jack The GPS wireless antenna jack allows you to connect a wireless antenna for GPS signals. NOTE: The GPS wireless antenna is optional and may not come bundled.
LAN port The Realtek® RTL8211 Ethernet controllers with 8-pin RJ-45 LAN port supports a standard Ethernet cable for 10/100/1000 Mbps connection to a local network. LAN port The Intel® I211-AT Gigabit Ethernet controllers with 8-pin RJ-45 LAN port supports a standard Ethernet cable for 10/100/1000 Mbps connection to a local network.
HDMI™ port The integrated 19-pin HDMI™ (High Definition Multimedia Interface) 2.0 port with a receptacle connector can support resolutions up to 3840 x 2160 @ 60 Hz on external display devices. USB 3.2 Gen 1 port The USB 3.2 Gen 1 (Universal Serial Bus) port provides a transfer rate up to 5 Gbit/s and a maximum of 5V/0.9A output per port. Nano SIM card slot with metal cover The hot-swappable nano SIM slot is located on the front panel for easy access. NOTE: This slot is covered with a metal cover.
Rear view WLAN wireless antenna jack The WLAN antenna jack allows to connect a wireless antenna to enhance Wi-Fi signals.
Isolated DIO connector DI4 L DI4 H DI3 L DI3 H DI2 L DI2 H DI1 L DI1 H DO4 L DO4 H DO3 L DO3 H DO2 L DO2 H DO1 L DO1 H The Isolated Digital Input/Output (DIO) connector provides electrical isolation (up to 2500 VDC) of digital input and output signals, which allow micro controllers to detect and output logic states. The high voltage protection can be used in industrial level uses. Please refer to the illustration below for the Isolated DIO connector’s pin definitions.
1.2 Motherboard Overview 1.2.1 Motherboard layout The PE100A is an Embedded Computer based on a Pico-ITX motherboard and is supported by a secondary I/O board for extra functionality. Refer to the table for the page numbers of the numbered items.
Secondary I/O board 16 PE100A
Layout contents Page Pico-ITX motherboard 1. Boot Mode switch 18 2. M.2 Wi-Fi slot 19 3. Micro SD card slot 19 4. I2C connector 20 5. SPI TPM connector 20 6. RTC Battery connector 21 7. IO Board-to-Board connector 22 Secondary I/O board 1. IO board switch 23 2. mPCIe / mSATA slot 24 3. Motherboard Board-to-Board connector 25 4.
1.2.2 1. Pico-ITX motherboard Boot Mode switch The Boot Mode switch allows you to configure between different boot modes and the location to boot from. Please refer to the table below for the different boot modes.
2. M.2 Wi-Fi slot The M.2 Wi-Fi slot allows you to install an M.2 Wi-Fi module (E-key, type 2230). NOTE: The M.2 Wi-Fi module is purchased separately. 3. Micro SD Card slot The micro SD Card slot allows you to install a micro SD card. NOTE: The micro SD card is purchased separately.
4. I2C connector The I2C (Inter-Integrated Circuit) connector allows you to connect an I2C compatible device. Connector type 5. Header 2x3p, K6, 2.0mm pitch SPI TPM connector The SPI TPM connector supports a Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity. Connector type 20 PE100A Header 2x7p,K14, 2.
6. RTC Battery connector The RTC Battery connector allows you to connect a lithium CMOS battery.
7. IO Board-to-Board connector The IO Board-to-Board connector allows you to connect the Pico-ITX motherboard and secondary I/O board.
1.2.3 1. Secondary I/O board IO board switch The IO Board switch allows you to configure between different configurations for the onboard slots and ports. Refer to the tables below for the different switch configurations.
2. mPCIe / mSATA slot The mPCIe/mSATA slot allows you to install an mPCIe peripheral device or an mSATA peripheral device. The default setting for the slot is mPCIe. To switch to mSATA, please refer to IO board switch. NOTE: The mPCIe / mSATA peripheral device is purchased separately.
3. Motherboard Board-to-Board connector The Motherboard Board-to-Board connector allows you to connect the Pico-ITX motherboard and secondary I/O board.
4. Nano SIM Card slot The nano SIM card slot allows you to install a nano SIM card. NOTE: The nano SIM card is purchased separately.
Using your Embedded Computer 2
2.1 Getting started 2.1.1 Connect the AC power adapter to your Embedded Computer To connect the AC power adapter to your Embedded Computer: A. Connect the power cord to the AC power adapter. B. Connect the AC power adapter to the terminal block power adapter. C. Connect the 2-pin terminal block DC power connector into your Embedded Computer’s power (DC) input. D. Plug the AC power adapter into a 100V~240 V power source.
IMPORTANT! • We strongly recommend that you use only the AC power adapter and cable that came with your Embedded Computer. • We strongly recommend that you use a grounded wall socket while using your Embedded Computer. • The socket outlet must be easily accessible and near your Embedded Computer. • To disconnect your Embedded Computer from its main power supply, unplug your Embedded Computer from the power socket.
2.1.2 Connect a display panel to your Embedded Computer You can connect a display panel or projector to your Embedded Computer that has the following connector(s): • HDMI™ connector To connect a display panel to your Embedded Computer: Connect one end of an HDMI™ cable to an external display, and the other end of the cable to your Embedded Computer’s HDMI™ port.
2.1.3 Connect the USB cable from keyboard or mouse You can connect generally any USB keyboard and mouse to your Embedded Computer. You can also connect a USB dongle for a wireless keyboard and mouse set. To connect a keyboard and mouse to your Embedded Computer: Connect the USB cable from your keyboard and mouse to any of the USB ports of your Embedded Computer. NOTE: • The keyboard varies with country and/or region. • The keyboard and mouse are purchased separately.
2.1.4 Turn on your Embedded Computer Press the power button to turn on your Embedded Computer. NOTE: The Embedded Computer will power on automatically the first time it is connected to a power source.
2.2 Turning off your Embedded Computer If your Embedded Computer is unresponsive, press and hold the power button for at least ten (10) seconds until your Embedded Computer turns off.
PE100A
3 Upgrading your Embedded Computer
IMPORTANT! • Ensure that your hands are dry before proceeding with the rest of the installation process. Before installing any of the features in this guide, use a grounded wrist strap or touch a safely grounded object or metal object to avoid damaging them due to static electricity. • Turn off the power of your Embedded Computer and allow it to cool for at least 10 minutes before performing any installation/ uninstallation process. NOTE: The illustrations in this section are for reference only.
3.2 Replacing the bottom cover 1. Align the bottom cover latches with the latch holes on the bottom of your Embedded Computer. 2. Secure the bottom cover using the screw removed previously.
3.3 Removing the top cover 1. Turn off your Embedded Computer, and then disconnect all cables and peripherals. 2. Remove the four (4) rubber feet screws from the bottom of the Embedded Computer (A), and then remove the top cover (B).
3.4 1. Replacing the top cover Place the top cover into the Embedded Computer chassis and ensure the ASUS IoT logo is on the left side of the top cover when you are facing the front of the Embedded Computer. IMPORTANT! Ensure that the RF cables and/or other cables are not under or in the way of the top cover when installing it, as this may cause the antennas to not work properly. 2. Secure the top cover from the bottom of the Embedded Computer using the four (4) rubber feet screws removed previously.
3.5 Installing a nano SIM card (Front panel) NOTE: This Nano SIM slot is hot swappable. 1. Remove the two (2) screws securing the Nano SIM card slot cover, and then remove the cover. 2. Insert the nano SIM card into the slot. 3. Replace slot cover and secure it with the screws removed previously.
3.6 Installing an SD card (Top side) Insert your SD card into the SD card slot. Ensure that the SD card is pushed all the way into the SD card slot.
3.7 Installing a wireless card to the M.2 slot (Top side) 1. Remove the M.2 stand screw. 2. Align and insert the wireless card into its slot inside the Embedded Computer. 3. Gently push down the wireless card on top of the screw hole, and then fasten it using the previously removed stand screw. 4. (optional) Connect the RF cables from the antennas to your wireless card. Ensure that the correct cable is attached to each of the connectors by following the color coding chart on the next page. 5.
WIFI-Aux (DIV) WIFI-Main WIFI-Aux (DIV) WIFI-Main Antenna Color Coding Band Color Antenna Type Black WIFI-Aux (DIV) Black WIFI-Main PE100A 43
3.8 Installing an mPCIe / mSATA module (Bottom side) Your Embedded Computer comes with an mPCIe / mSATA slot that allows you to install an LTE mPCIe module, mPCIe Coral TPU module, or mSATA storage module. To install an LTE mPCIe module: 1. Remove the two (2) standoff screws 2. Align and insert the LTE module into the slot. 3. Press down, and then secure it in place using the two (2) screws previously removed. 4. (optional) Connect the RF cables from the antennas to your LTE module.
Antenna Color Coding Band Color Antenna Type White LTE-Aux (DIV) Blue LTE-Main Red GPS PE100A 45
To install an mPCIe TPU module: 1. Align and insert the mPCIe TPU module into the slot. 2. Press down, and then secure it in place using the two (2) screws bundled with the module. To install an mSATA storage module: 1. Align and insert the mSATA storage module into the slot. 2. Press down, and then secure it in place using the two (2) screws bundled with the module.
3.9 Installing antennas (optional) You may install antennas to the five (5) antenna jacks located on the front and rear panels. The installed antennas can be connected to an LTE card installed in the Mini PCIe/mSATA slot (bottom side) or to a wireless card installed in the M.2 Wi-Fi slot (top side). NOTE: • It is recommended that you install the antennas connected to the LTE card to the front panel and the antennas connected to the wireless card to the rear panel (see below diagram).
Installing wireless card antennas NOTE: If your Embedded Computer came pre-installed with wireless card antenna jacks, skip to step 9. 1. Remove the rear panel cover by removing the four (4) screws from the cover. 2. Prepare the RF connector and cable. 3. Remove the rubber caps from the antenna holes. 4. Insert the antenna jack end of the RF connector and cable into the antenna jack from within the chassis outwards.
5. Insert the bundled O-ring to the antenna jack, then secure the antenna jack using bundled hex screw. 6. Connect the other end of the RF connector and cable to your wireless card. Refer to Installing a wireless card to the M.2 slot (Top side) for details. 7. Replace the rear panel cover, and secure it using the four (4) screws previously removed. 8. Replace the top cover. Refer to Replacing the top cover for details. 9.
Installing LTE and GPS antennas NOTE: If your Embedded Computer came pre-installed with LTE and GPS antenna jacks, skip to step 10. 1. Remove the front panel cover by removing the four (4) screws from the cover. 2. Prepare the RF connectors and cables. 3. Remove the rubber caps from the antenna holes. 4. Insert the antenna jack end of the RF connectors and cables into the antenna jacks from within the chassis outwards. 5.
7. Connect the other end of the RF connectors and cables to your WLAN card. Refer to Installing an mPCIe module to the Mini PCIe/mSATA slot (Bottom side) for details.
8. Replace the front panel, and then secure it using the four (4) screws previously removed. 9. Replace the top and bottom covers. Refer to Replacing the top cover and Replacing the bottom cover for details. 10. Screw the external LTE and GPS antennas onto their corresponding antenna jacks on the front panel by turning them in a clockwise direction. 11. Position the antennas for optimal signal reception.
3.10 Installing the wall mount 1. Remove the four (4) rubber feet screws. 2. Align the wall mount with the rubber feet screw holes, then remove the rubber feet from the rubber feet screws and secure the wall mount to your Embedded Computer using the rubber feet screws. NOTE: The rubber feet screws and wall mount screws are the same screws.
3.11 Installing DIN rail clips (optional) 1. Make sure that the wall mount is already installed. Refer to the section Installing the wall mount for installation instructions. 2. Align the screw holes on the DIN rail clips to the ones on the wall mount as shown below. 3. Secure the DIN rail clips to the wall mount using the screws bundled with the DIN rail clips. 4.
3.12 Installing the terminal block (optional) You may install terminal blocks into the Serial (COM) terminal connector and Isolated DIO connector, which allow you to support additional devices with serial ports or micro controllers by referring to the pin definitions and connecting cables to the slots on the terminal blocks as needed. IMPORTANT! Connect only one (1) cable to a slot on the terminal block. NOTE: • The terminal block is purchased separately.
Installing a terminal block to the Isolated DIO connector 56 PE100A
4 Setting up your Embedded Computer PE100A 57
4.1 Requirements Before you start setting up your Embedded Computer, make sure you have the following available: • 1 x USB Type-C® cable with data transfer function (to connect your PC to your Embedded Computer’s data port) • 1 x Power supply • 1 x Monitor with HDMI™ cable • 1 x Keyboard and Mouse set NOTE: Ensure to use the bundled power supply, or, if you are using another power supply, ensure to use a 12~24V power supply. 4.
Initiating Fastboot mode: 1. Connect the USB Type-C® cable to the USB Type-C® ports on your Embedded Computer and host computer. 2. Power on your Embedded Computer, you should automatically be booted into Fastboot mode. NOTE: • Please note that you will only be booted into Fastboot mode when booting up your Embedded Computer for the first time. • Please refer to the readme file in the unzipped image folder for details on other items, such as re-flash or recovery. Executing the flash script: 1.
PE100A
Appendix
Safety information Your Embedded Computer is designed and tested to meet the latest standards of safety for information technology equipment. However, to ensure your safety, it is important that you read the following safety instructions. Setting up your system • • • • • • • • • 62 Read and follow all instructions in the documentation before you operate your system. Do not use this product near water or a heated source. Set up the system on a stable surface.
Care during use • Do not walk on the power cord or allow anything to rest on it. • • Do not spill water or any other liquids on your system. When the system is turned off, a small amount of electrical current still flows. Always unplug the power cord from the power outlets before cleaning the system. Use this product with care when operating at full load, as the product may reach temperatures of up to 60˚C and the outer casing may reach temperatures of up to 73˚C.
DO NOT throw the Embedded Computer in municipal waste. This product has been designed to enable proper reuse of parts and recycling. This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment, and mercurycontaining button cell battery) should not be placed in municipal waste. Check local technical support services for product recycling.
Regulatory notices COATING NOTICE IMPORTANT! To provide electrical insulation and maintain electrical safety, a coating is applied to insulate the device except on the areas where the I/O ports are located. Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules.
RF exposure warning This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
Compliance Statement of Innovation, Science and Economic Development Canada (ISED) This device complies with Innovation, Science and Economic Development Canada licence exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
VCCI: Japan Compliance Statement Class A ITE Japan RF Equipment Statement 屋外での使用について 本製品は、5GHz帯域での通信に対応しています。電波法の定めにより 5.2GHz、5.
Declaration of compliance for product environmental regulation ASUS follows the green design concept to design and manufacture our products, and makes sure that each stage of the product life cycle of ASUS product is in line with global environmental regulations. In addition, ASUS disclose the relevant information based on regulation requirements. Please refer to http://csr.asus.com/Compliance.
Turkey RoHS AEEE Yönetmeliğine Uygundur ASUS Recycling/Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for you to be able to responsibly recycle our products, batteries, other components as well as the packaging materials. Please go to http:// csr.asus.com/english/Takeback.htm for detailed recycling information in different regions.
甲類警語 警告使用者：此為甲類資訊技術設備，於居住環境中使用時，可能會造 成射頻擾動，在此種情況下，使用者會被要求採取某些適當的對策。 Taiwan BSMI Class A Notice This product is Class A. In a domestic environment, this product may cause radio interference. You may be required to take adequate measures.
ENERGY STAR complied product ENERGY STAR is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy helping us all save money and protect the environment through energy efficient products and practices. All ASUS products with the ENERGY STAR logo comply with the ENERGY STAR standard, and the power management feature is enabled by default.
UK: The Radio Equipment Regulations 2017 (S.I. 2017/1206) Simplified UKCA Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of The Radio Equipment Regulations 2017 (S.I. 2017/1206). Full text of UKCA declaration of conformity is available at https://www.asus.com/support/.
EU: Radio Equipment Directive (Directive 2014/53/EU) Simplified EU Declaration of Conformity ASUSTek Computer Inc. hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of EU declaration of conformity is available at https://www.asus.
Zjednodušené prohlášení o shodě EU Společnost ASUSTek Computer Inc. tímto prohlašuje, že toto zařízení splňuje základní požadavky a další příslušná ustanovení směrnice 2014/53/ EU. Plné znění prohlášení o shodě EU je k dispozici na adrese https://www.asus.com/support/ V zemích uvedených v tabulce je provoz sítě Wi-Fi ve frekvenčním rozsahu 5 150 - 5 350 MHz povolen pouze ve vnitřních prostorech: Forenklet EU-overensstemmelseserklæring ASUSTeK Computer Inc.
Vienkāršota ES atbilstības paziņojums ASUSTeK Computer Inc. ar šo paziņo, ka šī ierīce atbilst Direktīvas 2014/53/ES būtiskajām prasībām un citiem citiem saistošajiem nosacījumiem. Pilns ES atbilstības paziņojuma teksts pieejams šeit: https://www.asus.com/support/ Wi-Fi darbība 5150–5350 MHz ir jāierobežo lietošanai telpās valstīs, kuras norādītas tālāk. Supaprastinta ES atitikties deklaracija Šiame dokumente bendrovė „ASUSTek Computer Inc.
Förenklad EU-försäkran om överensstämmelse ASUSTek Computer Inc. deklarerar härmed att denna enhet överensstämmer med de grundläggande kraven och andra relevanta bestämmelser i direktiv 2014/53/EU. Fullständig text av EU-försäkran om överensstämmelse finns på https://www.asus.com/support/ WiFi som använder 5150-5350 MHz kommer att begränsas för användning inomhus i de länder som anges i tabellen: ประกาศเกี่ยวกับความสอดคล้องของสหภาพยุโรปแบบย่อ ASUSTek Computer Inc.
CE RED RF Output table (Directive 2014/53/EU) QUECTEL (Model: EC25-G) Radio Type WCDMA LTE Description Frequency Maximum Output Power (EIRP) 900 880 - 915 MHz 35.0 dBm 1800 1710 - 1785 MHz 32.0 dBm Band 1 1920 - 1980 MHz 25.0 dBm Band 5 824 - 849 MHz 25.0 dBm Band 8 880 - 915 MHz 25.0 dBm B1 1920 - 1980 MHz 25.0 dBm B3 1710 - 1785 MHz 25.0 dBm B5 824 - 849 MHz 25.0 dBm B7 2500 - 2570 MHz 25.0 dBm B8 880 - 915 MHz 25.0 dBm B20 832 - 862 MHz 25.
Manufacturer ASUSTeK Computer Inc. Tel: +886-2-2894-3447 Address: 1F., No. 15, Lide Rd., Beitou Dist.
PE100A
