User Manual
Table Of Contents
- About this manual
- Chapter 1: Getting to know your Embedded Computer
- Chapter 2: Using your Embedded Computer
- Chapter 3: Upgrading your Embedded Computer
- 3.1 Removing the bottom cover
- 3.2 Replacing the bottom cover
- 3.3 Installing memory modules
- 3.4 Installing 2.5” storage device
- 3.5 Installing an M.2 SSD
- 3.6 Installing a nano SIM card
- 3.7 Installing an SD card
- 3.8 Installing a wireless card to the M.2 slot
- 3.9 Installing an mPCIe / mSATA module
- 3.10 Installing antennas (optional)
- 3.11 Installing the USB 2.0 module (on selected models)
- 3.12 Installing the Serial port module (on selected models)
- 3.13 Installing the PoE LAN module (on selected models)
- 3.14 Installing the VESA mount (optional)
- 3.15 Installing the wall mount
- 3.16 Installing DIN rail clips (optional)
- Chapter 4: BIOS Setup
- 4.1 Getting to know your BIOS
- 4.2 BIOS setup program
- 4.3 Main Menu
- 4.4 Advanced menu
- 4.4.1 Trusted Computing
- 4.4.2 PCH Storage Configuration
- 4.4.3 Onboard Devices Configuration
- 4.4.4 ACPI Settings
- 4.4.5 APM Configuration
- 4.4.6 SMART Settings
- 4.4.7 NCT6116D Super IO Configuration
- 4.4.8 NCT6116D HW Monitor
- 4.4.9 Serial Port Console Redirection
- 4.4.10 CPU Configuration
- 4.4.11 AMI Graphic Output Protocol Policy
- 4.4.12 PCI Subsystem Settings
- 4.4.13 USB Configuration
- 4.4.14 Network Stack Configuration
- 4.4.15 SDIO Configuration
- 4.4.16 Platform Trust Technology
- 4.4.17 Security Configuration
- 4.4.18 Thermal
- 4.5 Security
- 4.6 Boot menu
- 4.7 Save & Exit menu
- 4.8 Updating your BIOS
- Chapter 5: Watchdog Timer
- Appendix
PE Series
109
WARNING
• This function can support devices such as a USB ash disk with FAT
32/16 format and single partition only.
• DO NOT shut down or reset the system while updating the BIOS to
prevent system boot failure!
IMPORTANT! Ensure to load the BIOS default settings to ensure system
compatibility and stability. Press <F5> and select Yes to load the BIOS
default settings.
4.8.3 BUPDATER utility
NOTE: The succeeding BIOS screens are for reference only. The actual
BIOS screen displays may not be the same as shown.
The BUPDATER utility allows you to update the BIOS le in DOS environment
using a bootable USB ash disk drive with the updated BIOS le.
Updating the BIOS le
To update the BIOS le using the BUPDATER utility:
1. Visit the ASUS website at www.asus.com and download the latest BIOS
le for the motherboard. Save the BIOS le to a bootable USB ash disk
drive.
2. Download the BUPDATER utility (BUPDATER.exe) from the ASUS
support website at support.asus.com to the bootable USB ash disk
drive you created earlier.
3. Boot the system in DOS mode, then at the prompt, type:
BUPDATER /i[lename].CAP
where [lename] is the latest or the original BIOS le on the bootable
USB ash disk drive, then press <Enter>.
A:\>BUPDATER /i[le name]CAP