User Manual
Table Of Contents
- About this manual
- Chapter 1: Getting to know your Embedded Computer
- Chapter 2: Using your Embedded Computer
- Chapter 3: Upgrading your Embedded Computer
- 3.1 Removing the bottom cover
- 3.2 Replacing the bottom cover
- 3.3 Installing memory modules
- 3.4 Installing 2.5” storage device
- 3.5 Installing an M.2 SSD
- 3.6 Installing a nano SIM card
- 3.7 Installing an SD card
- 3.8 Installing a wireless card to the M.2 slot
- 3.9 Installing an mPCIe / mSATA module
- 3.10 Installing antennas (optional)
- 3.11 Installing the USB 2.0 module (on selected models)
- 3.12 Installing the Serial port module (on selected models)
- 3.13 Installing the PoE LAN module (on selected models)
- 3.14 Installing the VESA mount (optional)
- 3.15 Installing the wall mount
- 3.16 Installing DIN rail clips (optional)
- Chapter 4: BIOS Setup
- 4.1 Getting to know your BIOS
- 4.2 BIOS setup program
- 4.3 Main Menu
- 4.4 Advanced menu
- 4.4.1 Trusted Computing
- 4.4.2 PCH Storage Configuration
- 4.4.3 Onboard Devices Configuration
- 4.4.4 ACPI Settings
- 4.4.5 APM Configuration
- 4.4.6 SMART Settings
- 4.4.7 NCT6116D Super IO Configuration
- 4.4.8 NCT6116D HW Monitor
- 4.4.9 Serial Port Console Redirection
- 4.4.10 CPU Configuration
- 4.4.11 AMI Graphic Output Protocol Policy
- 4.4.12 PCI Subsystem Settings
- 4.4.13 USB Configuration
- 4.4.14 Network Stack Configuration
- 4.4.15 SDIO Configuration
- 4.4.16 Platform Trust Technology
- 4.4.17 Security Configuration
- 4.4.18 Thermal
- 4.5 Security
- 4.6 Boot menu
- 4.7 Save & Exit menu
- 4.8 Updating your BIOS
- Chapter 5: Watchdog Timer
- Appendix
PE Series
89
NOTE: The following items appear only when Power Limit 1 Enable is
set to [Enabled].
Power Limit 1
Power Limit 1 Clamp Mode
Allows you to enable or disable Power Limit 1 Clamp Mode.
Conguration options: [Disabled] [Enabled]
Power Limit 1 Power
Allows you to set the Power Limit 1 in Watts. Selecting [Auto] will
program Power Limit 1 Power based on the silicon default support
value.
Conguration options: [Auto] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15]
[16] [17] [18] [19] [20] [21] [22] [23] [24] [25]
Power Limit 1 Time Window
Allows you to set the Power Limit 1 Time Window value in Seconds.
Selecting [Auto] will program Power Limit 1 Time Window based on
the silicon default support value.
Conguration options: [Auto] [1] [2] [3] [4] [5] [6] [7] [8] [10] [12] [14]
[16] [20] [24] [28] [32] [40] [48] [56] [64] [80] [96] [112]
Active Processor Cores
Allows you to enable or disable selecting the number of CPU cores to
activate in each processor package.
Conguration options: [Disabled] [Enabled]
NOTE: The following items appear only when Active Processor Cores
is set to [Enabled].
Core 1-3
Allows you to enable or Core 1-3.
Conguration options: [Disabled] [Enabled]