User’s Manual
Table Of Contents
- About this manual
- Chapter 1: Getting to know your Edge Computer
- Chapter 2: Using your Edge Computer
- Chapter 3: Upgrading your Edge Computer
- 3.1 Removing the bottom cover
- 3.2 Replacing the bottom cover
- 3.3 Installing memory modules
- 3.4 Installing 2.5” storage device
- 3.5 Installing the Mini PCIe card
- 3.6 Installing a nano SIM card
- 3.7 Installing an SD card
- 3.8 Installing the wireless card
- 3.9 Installing an M.2 SSD
- 3.10 Installing the antennas (optional)
- 3.11 Installing the USB 2.0 module (on selected models)
- 3.12 Installing the Serial port module (on selected models)
- 3.13 Installing the PoE LAN module (on selected models)
- 3.14 Installing the VESA mount (optional)
- 3.15 Installing the wall mount
- Chapter 4: BIOS Setup
- 4.1 Getting to know your BIOS
- 4.2 BIOS setup program
- 4.3 Main Menu
- 4.4 Advanced menu
- 4.4.1 Trusted Computing
- 4.4.2 PCH Storage Configuration
- 4.4.3 Onboard Devices Configuration
- 4.4.4 ACPI Settings
- 4.4.5 APM Configuration
- 4.4.6 SMART Settings
- 4.4.7 NCT6116D Super IO Configuration
- 4.4.8 NCT6116D HW Monitor
- 4.4.9 Serial Port Console Redirection
- 4.4.10 CPU Configuration
- 4.4.11 AMI Graphic Output Protocol Policy
- 4.4.12 PCI Subsystem Settings
- 4.4.13 USB Configuration
- 4.4.14 Network Stack Configuration
- 4.4.15 SDIO Configuration
- 4.4.16 Platform Trust Technology
- 4.4.17 Security Configuration
- 4.4.18 Thermal
- 4.5 Security
- 4.6 Boot menu
- 4.7 Save & Exit menu
- 4.8 Updating your BIOS
- Appendix
112
PE200S Series
ComplianceStatementofInnovation,ScienceandEconomic
Development Canada (ISED)
This device complies with Innovation, Science and Economic Development
Canada licence exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may
cause undesired operation of the device.
CAN ICES-3(A)/NMB-3(A)
DéclarationdeconformitédeInnovation,Scienceset
Développement économique Canada (ISED)
Le présent appareil est conforme aux CNR d’Innovation, Sciences et
DéveloppementéconomiqueCanadaapplicablesauxappareilsradio
exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur
del’appareildoitacceptertoutbrouillageradioélectriquesubi,mêmesile
brouillage est susceptible d’en compromettre le fonctionnement.
CAN ICES-3(A)/NMB-3(A)
ISEDRadiationExposureStatementforCanada
ThisequipmentcomplieswithISEDradiationexposurelimitssetforthforan
uncontrolled environment. To maintain compliance with ISED RF exposure
compliancerequirements,pleaseavoiddirectcontacttothetransmitting
antenna during transmitting. End users must follow the specic operating
instructions for satisfying RF exposure compliance.
Operation is subject to the following two conditions:
• Thisdevicemaynotcauseinterferenceand
• Thisdevicemustacceptanyinterference,includinginterferencethat
may cause undesired operation of the device.