User Manual
Table Of Contents
- Mellanox WinOF VPI User Manual
- Table of Contents
- List of Tables
- Document Revision History
- About this Manual
- 1 Introduction
- 2 Driver Features
- 3 Deploying Windows Server 2012 with SMB Direct
- 4 Driver Configuration
- 5 Performance Tuning
- 6 OpenSM - Subnet Manager
- 7 InfiniBand Fabric
- 7.1 Network Direct Interface
- 7.2 part_man - Virtual IPoIB Port Creation Utility
- 7.3 InfiniBand Fabric Diagnostic Utilities
- 7.4 InfiniBand Fabric Performance Utilities
- 7.4.1 ib_read_bw
- 7.4.2 ib_read_lat
- 7.4.3 ib_send_bw
- 7.4.4 ib_send_lat
- 7.4.5 ib_write_bw
- 7.4.6 ib_write_lat
- 7.4.7 ibv_read_bw
- 7.4.8 ibv_read_lat
- 7.4.9 ibv_send_bw
- 7.4.10 ibv_send_lat
- 7.4.11 ibv_write_bw
- 7.4.12 ibv_write_lat
- 7.4.13 ibaddr
- 7.4.14 ibcacheedit
- 7.4.15 iblinkinfo
- 7.4.16 ibqueryerrors
- 7.4.17 ibsysstat
- 7.4.18 perfquery
- 7.4.19 saquery
- 7.4.20 smpdump
- 8 Software Development Kit
- 9 Troubleshooting
- 10 Documentation
WinOF VPI for Windows User Manual Rev 4.3
Mellanox Technologies
54
2. Query the status of two channel adapters using directed paths.
3. Change the speed of a port.
> ibportstate -C mlx4_0 -D 0 1
PortInfo:
# Port info: DR path slid 65535; dlid 65535; 0 port 1
LinkState:.......................Initialize
PhysLinkState:...................LinkUp
LinkWidthSupported:..............1X or 4X
LinkWidthEnabled:................1X or 4X
LinkWidthActive:.................4X
LinkSpeedSupported:..............2.5 Gbps or 5.0 Gbps
LinkSpeedEnabled:................2.5 Gbps or 5.0 Gbps
LinkSpeedActive:.................5.0 Gbps
> ibportstate -C mthca0 -D 0 1
PortInfo:
# Port info: DR path slid 65535; dlid 65535; 0 port 1
LinkState:.......................Down
PhysLinkState:...................Polling
LinkWidthSupported:..............1X or 4X
LinkWidthEnabled:................1X or 4X
LinkWidthActive:.................4X
LinkSpeedSupported:..............2.5 Gbps
LinkSpeedEnabled:................2.5 Gbps
LinkSpeedActive:.................2.5 Gbps
# First query for current configuration
> ibportstate -C mlx4_0 -D 0 1
PortInfo:
# Port info: DR path slid 65535; dlid 65535; 0 port 1
LinkState:.......................Initialize
PhysLinkState:...................LinkUp
LinkWidthSupported:..............1X or 4X
LinkWidthEnabled:................1X or 4X
LinkWidthActive:.................4X
LinkSpeedSupported:..............2.5 Gbps or 5.0 Gbps
LinkSpeedEnabled:................2.5 Gbps or 5.0 Gbps
LinkSpeedActive:.................5.0 Gbps
# Now change the enabled link speed
> ibportstate -C mlx4_0 -D 0 1 speed 2
ibportstate -C mlx4_0 -D 0 1 speed 2
Initial PortInfo:
# Port info: DR path slid 65535; dlid 65535; 0 port 1
LinkSpeedEnabled:................2.5 Gbps
After PortInfo set:
# Port info: DR path slid 65535; dlid 65535; 0 port 1
LinkSpeedEnabled:................5.0 Gbps (IBA extension)