User Manual
Table Of Contents
- Mellanox WinOF VPI User Manual
- Table of Contents
- List of Tables
- Document Revision History
- About this Manual
- 1 Introduction
- 2 Driver Features
- 3 Deploying Windows Server 2012 with SMB Direct
- 4 Driver Configuration
- 5 Performance Tuning
- 6 OpenSM - Subnet Manager
- 7 InfiniBand Fabric
- 7.1 Network Direct Interface
- 7.2 part_man - Virtual IPoIB Port Creation Utility
- 7.3 InfiniBand Fabric Diagnostic Utilities
- 7.4 InfiniBand Fabric Performance Utilities
- 7.4.1 ib_read_bw
- 7.4.2 ib_read_lat
- 7.4.3 ib_send_bw
- 7.4.4 ib_send_lat
- 7.4.5 ib_write_bw
- 7.4.6 ib_write_lat
- 7.4.7 ibv_read_bw
- 7.4.8 ibv_read_lat
- 7.4.9 ibv_send_bw
- 7.4.10 ibv_send_lat
- 7.4.11 ibv_write_bw
- 7.4.12 ibv_write_lat
- 7.4.13 ibaddr
- 7.4.14 ibcacheedit
- 7.4.15 iblinkinfo
- 7.4.16 ibqueryerrors
- 7.4.17 ibsysstat
- 7.4.18 perfquery
- 7.4.19 saquery
- 7.4.20 smpdump
- 8 Software Development Kit
- 9 Troubleshooting
- 10 Documentation
WinOF VPI for Windows User Manual Rev 4.3
Mellanox Technologies
64
3. Read then reset performance counters from LID 2, port 1.
7.3.7 ibping
ibping uses vendor MADs to validate connectivity between IB nodes. On exit, (IP) ping like out-
put is shown. ibping is run as client/server, however the default is to run it as a client. Note also
that in addition to ibping, a default server is implemented within the kernel.
7.3.7.1 ibping Synopsys
7.3.7.2 ibping Options
The table below lists the various flags of the command.
XmtPkts:.........................1803332
RcvPkts:.........................1799018
> perfquery -r 2 1
# Port counters: Lid 2 port 1
PortSelect:......................1
CounterSelect:...................0x0100
SymbolErrors:....................0
LinkRecovers:....................0
LinkDowned:......................0
RcvErrors:.......................0
RcvRemotePhysErrors:.............0
RcvSwRelayErrors:................0
XmtDiscards:.....................3
XmtConstraintErrors:.............0
RcvConstraintErrors:.............0
LinkIntegrityErrors:.............0
ExcBufOverrunErrors:.............0
VL15Dropped:.....................0
XmtData:.........................0
RcvData:.........................0
XmtPkts:.........................0
RcvPkts:.........................0
ibping [-d(ebug)] [-e(rr_show)] [-v(erbose)] [-G(uid)] [-C ca_name] [-P ca_port]
[-s smlid] [-t(imeout)timeout_ms] [-V(ersion)] [-L(id)][-u(sage)] [-c ping_count] [-
f(lood)] [-o oui] [-S(erver)] [-h(elp)] <dest lid | guid>
Table 10 - ibping Flags and Options
Flag Description
--count, -c <num> Stops after count packets
-f, (--flood) Floods destination: send packets back to back without delay
-o, (--oui) Uses specified OUI number to multiplex vendor mads
--Server, -S Starts in server mode (do not return)
--debug, -d/-ddd/ -d -d -d Raises the IB debugging level