User Manual
Table Of Contents
- Mellanox WinOF VPI User Manual
- Table of Contents
- List of Tables
- Document Revision History
- About this Manual
- 1 Introduction
- 2 Driver Features
- 3 Deploying Windows Server 2012 with SMB Direct
- 4 Driver Configuration
- 5 Performance Tuning
- 6 OpenSM - Subnet Manager
- 7 InfiniBand Fabric
- 7.1 Network Direct Interface
- 7.2 part_man - Virtual IPoIB Port Creation Utility
- 7.3 InfiniBand Fabric Diagnostic Utilities
- 7.4 InfiniBand Fabric Performance Utilities
- 7.4.1 ib_read_bw
- 7.4.2 ib_read_lat
- 7.4.3 ib_send_bw
- 7.4.4 ib_send_lat
- 7.4.5 ib_write_bw
- 7.4.6 ib_write_lat
- 7.4.7 ibv_read_bw
- 7.4.8 ibv_read_lat
- 7.4.9 ibv_send_bw
- 7.4.10 ibv_send_lat
- 7.4.11 ibv_write_bw
- 7.4.12 ibv_write_lat
- 7.4.13 ibaddr
- 7.4.14 ibcacheedit
- 7.4.15 iblinkinfo
- 7.4.16 ibqueryerrors
- 7.4.17 ibsysstat
- 7.4.18 perfquery
- 7.4.19 saquery
- 7.4.20 smpdump
- 8 Software Development Kit
- 9 Troubleshooting
- 10 Documentation
InfiniBand FabricRev 4.3
Mellanox Technologies
69
Example
7.3.9 ibtracert
ibtracert uses SMPs to trace the path from a source GID/LID to a destination GID/LID. Each hop
along the path is displayed until the destination is reached or a hop does not respond. By using
the -m option, multicast path tracing can be performed between source and destination nodes.
7.3.9.1 ibtracert Synopsys
7.3.9.2 ibtracert Options
The table below lists the various flags of the command.
Most OpenIB diagnostics take the following common flags. The exact list of supported flags per
utility can be found in the usage message and can be shown using the util_name -h syntax..
# IB1
# Line cards
0x0008f104003f125c "IB1 (Rack 11 slot 1 ) ISR9288/ISR9096 Voltaire sLB-24D"
0x0008f104003f125d "IB1 (Rack 11 slot 1 ) ISR9288/ISR9096 Voltaire sLB-24D"
0x0008f104003f10d2 "IB1 (Rack 11 slot 2 ) ISR9288/ISR9096 Voltaire sLB-24D"
0x0008f104003f10d3 "IB1 (Rack 11 slot 2 ) ISR9288/ISR9096 Voltaire sLB-24D"
0x0008f104003f10bf "IB1 (Rack 11 slot 12 ) ISR9288/ISR9096 Voltaire sLB-24D"
# Spines
0x0008f10400400e2d "IB1 (Rack 11 spine 1 ) ISR9288 Voltaire sFB-12D"
0x0008f10400400e2e "IB1 (Rack 11 spine 1 ) ISR9288 Voltaire sFB-12D"
0x0008f10400400e2f "IB1 (Rack 11 spine 1 ) ISR9288 Voltaire sFB-12D"
0x0008f10400400e31 "IB1 (Rack 11 spine 2 ) ISR9288 Voltaire sFB-12D"
0x0008f10400400e32 "IB1 (Rack 11 spine 2 ) ISR9288 Voltaire sFB-12D"
# GUID Node Name
0x0008f10400411a08 "SW1 (Rack 3) ISR9024 Voltaire 9024D"
0x0008f10400411a28 "SW2 (Rack 3) ISR9024 Voltaire 9024D"
0x0008f10400411a34 "SW3 (Rack 3) ISR9024 Voltaire 9024D"
0x0008f104004119d0 "SW4 (Rack 3) ISR9024 Voltaire 9024D"
ibtracert [-d(ebug)] [-v(erbose)] [-D(irect)] [-L(id)] [-e(rrors)] [-u(sage)] [-
G(uids)] [-f(orce)] [-n(o_info)] [-m mlid] [-s smlid] [-C ca_name][-P ca_port] [-
t(imeout) timeout_ms] [-V(ersion)] [--node-name--map <node-name-map>] [-h(elp)]
[<dest dr_path|lid|guid> [<startlid> [<endlid>]]
Table 12 - ibtracert Flags and Options
Flag Description
--force, -f Force
-n, --no_info Simple format; do not show additional information
--mlid, -m <mlid> Show the multicast trace of the specified mlid
--node-name-map <node-name-
map>
Specify a node name map. The node name map file maps GUIDs to
more user friendly names. See “Topology File Format” on page 67.
--debug, -d/-ddd/-d -d -d Raise the IB debugging level