Motherboard PRIME/PRO/ ProArt/TUF GAMING B550/A520 系列 BIOS 用戶手冊
C16863 第一版 2020 年 7 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
Offer to Provide Source Code of Certain Software This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.
目錄 4 1.1 認識 BIOS 程序.............................................................................................................5 1.2 BIOS 設置程序..............................................................................................................6 1.2.1 EZ Mode......................................................................................................7 1.2.2 Advanced Mode......................................................................................8 1.2.3 Q-Fan 控制.........
BIOS 程序設置 1.
1.
1.2.
1.2.
功能表列 BIOS 設置程序最上方各菜單功能說明如下: My Favorites 本項目將記錄時常使用的系統設置及設置值。 Main 本項目提供系統基本設置。 Ai Tweaker 本項目提供超頻設置。 Advanced 本項目提供系統高級功能設置。 Monitor 本項目提供溫度、電源及風扇功能設置。 Boot 本項目提供啟動磁盤設置。 Tool 本項目提供特殊功能設置。 Exit 本項目提供退出 BIOS 設置程序與出廠默認值還原功能。 菜單項目 在功能表列選定選項時,被選擇的功能將會反白,即可選擇 Main 菜單所出現的項目。 點擊菜單中的其他項目(例如:My Favorite、Ai Tweaker、Advanced、Monitor、 Boot、Tool 與 Exit)也會出現該項目各自不同的選項。 子菜單 在菜單畫面中,若功能選項前面有一個小三角形標記(>),代表此為子菜單,您可利 用方向鍵來選擇,並按下 鍵來進入子菜單。 語言 這個按鈕位在功能表列的上方,用來選擇 BIOS 程序界面顯示的語言。點擊這個按鈕 來選擇您想要的 BIOS 畫面顯示語言。
AURA 開關(F4) 這個按鈕用來開啟或關閉 RGB LED 指示燈或功能性 LED 指示燈。 [All On]: 所有指示燈(Aura 及功能性指示燈)將開啟。 [Aura Only]: Aura 指示燈將開啟,而功能性指示燈將關閉。 [Aura Off]: Aura 指示燈將關閉,而功能性指示燈仍然開啟。 [Stealth Mode]: 所有指示燈(Aura 及功能性指示燈)將關閉。 快捷鍵 這個按鈕包含有 BIOS 程序設置的導引方向鍵,使用導引方向鍵來選擇菜單中的項目 並更改設置。 滾動條 在菜單畫面的右方若出現滾動條,即代表此頁選項超過可顯示的畫面,您可利用上/下 方向鍵或是 / 按鍵來顯示畫面中的其他項目。 項目說明 在菜單畫面的下方為當前所選擇的作用選項的功能說明,此說明會依選項的不同而自動 更改。使用 按鍵來抓取 BIOS 屏幕畫面,並保存至攜帶式存儲設備。 設置窗口 此區域顯示菜單項目的設置值。若項目是用戶可以設置的,您可以更改該項目的數值; 若是無法設置,則無法選取該項目。 設置值被選擇後會以反白顯示。要改變設置值請選擇
1.2.
手動設置風扇 從設置文件清單中選擇 Manual 來手動設置風扇運行的速度。 速度點 點擊以手動設置風扇 請依照以下步驟設置風扇: 12 1. 選擇想要設置的風扇並查看該風扇現在的狀況。 2. 點擊並拖曳速度點來調整風扇的運行速度。 3.
1.
添加項目至收藏夾 請依照以下步驟添加項目至收藏夾: 1. 在鍵盤按下 鍵或在 BIOS 程序畫面中點擊 圖畫面。 2. 在設置樹狀圖畫面中選擇想要保存至收藏夾的 BIOS 項目。 來啟動設置樹狀 主菜單面板 已選擇的快捷 方式項目 子菜單面板 刪除所有最 愛項目 點擊以恢復 更改 3. 從主菜單面板選擇項目,然後點擊子菜單中想要保存至收藏夾的選項,再點擊或 輕觸 或是按下 按鍵。 以下項目無法加入至收藏夾: • 有子菜單的項目。 • 用戶自訂項目,例如:語言、啟動設備順序。 • 設置項目,例如:內存 SPD 信息、系統時間與日期。 14 4. 點擊 Exit (ESC) 或按下 鍵來關閉樹狀圖窗口。 5.
1.
系統管理員密碼(Administrator Password) 當您設置系統管理員密碼後,建議您先登入系統管理員帳戶,以免 BIOS 設置程序中 的某些信息無法查看或更改設置。 設置系統管理員密碼 請依照以下步驟設置系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 窗口輸入欲設置的密碼,輸入完成按下 。 3. 請再一次輸入密碼以確認密碼正確。 更改系統管理員密碼 請依照以下步驟更改系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3. 由 Create New Password 窗口輸入新密碼,輸入完成按下 。 4.
1.5 Ai Tweaker 菜單(Ai Tweaker) 本菜單可讓您設置超頻功能的相關選項。 注意!在您設置本高級菜單的設置時,不正確的設置值將導致系統功能 異常。 以下項目的默認值會隨著您的主板型號以及所安裝的處理器與內存型號 而不同。 向下滾動以顯示其他 BIOS 項目。 Ai Overclock Tuner 本項目可以讓您設置 CPU 的超頻選項來達到您所想要的 CPU 內頻。設置值有: [Auto] 載入系統優化設置值。 [Manual] 讓您個別設置超頻比值。 以下項目只有在 Ai Overclock Tuner 設置為 [Manual] 時才會出現。 BCLK Frequency 本項目用來設置 BCLK 頻率以增強系統性能。您可以使用 <+> 與 <-> 鍵調整數 值。數值變更的範圍為 96.0MHz 至 118.
Memory Frequency 本項目可讓您設置內存的運行頻率。設置選項會隨著 BCLK(基礎時鐘)頻率的設 置值變動。選擇自動模式以應用優化設置。設置值有:[Auto] [DDR4-1333MHz] – [DDR4-6000MHz] 設置過高的內存頻率將會導致系統的不穩定與硬件毀損, 當系統出現不穩 定的狀況時,建議您使用默認值。 FCLK Frequency 本項目用來指定 FCLK 頻率。 設置值有:[Auto] [666MHz] [800MHz] – [3000MHz] CPU Core Ratio 本項目用來設置處理器核心倍頻。您可以使用 <+> 與 <-> 鍵調整數值。設置值取決 於安裝的處理器。 CPU Core Ratio (Per CCX) Core VID 本項目用來設置自定義處理器核心 VID。您可以使用 <+> 與 <-> 鍵調整數值。 數值變更的範圍為 0.700 至 1.550。 CCX0/1 Ratio 本項目用來為此 CCX 設置自定義的核心倍頻。您可以使用 <+> 與 <-> 鍵調整數 值。數值變更的範圍為 28.00 至 63.
Max CPU Boost Clock Override 本項目可讓您通過 Precision Boost 2 算法自動增加最大處理器頻率值。設置 值有:[Auto] [0MHz] [25MHz] [75MHz] [100MHz] [125MHz] [150MHz] [175MHz] [200MHz] Platform Thermal Throttle Limit 本項目可用來降低允許的最高處理器溫度(攝氏度)。設置值有:[Auto] [Manual] DRAM Timing Control 本菜單中的項目可讓您設置內存時序控制功能。您可以使用 <+> 與 <-> 鍵調整數值。 當您要恢復默認值時,請使用鍵盤輸入 [auto] 並按下 鍵。 自行變更數值將會導致系統的不穩定與硬件損壞!當系統出現不穩定的狀 況時,建議您使用默認值。 DRAM CAS# Latency 設置值有:[Auto] [5] – [33] Trcdrd 設置值有:[Auto] [8] – [27] Trcdwr 設置值有:[Auto] [8] – [27] DRAM RAS# PRE Time 設置值有:[Auto]
Trcpage 設置值有:[Auto] [0] -[1023] TrdrdScl 設置值有:[Auto] [1] – [15] TwrwrScl 設置值有:[Auto] [1] – [63] Trfc 設置值有:[Auto] [60] – [1023] Trfc2 設置值有:[Auto] [60] – [1023] Trfc4 設置值有:[Auto] [60] – [990] Tcwl 設置值有:[Auto] [9] – [22] Trtp 設置值有:[Auto] [5] – [14] Trdwr 設置值有:[Auto] [1] – [31] Twrrd 設置值有:[Auto] [1] – [15] TwrwrSc 設置值有:[Auto] [1] – [15] TwrwrSd 設置值有:[Auto] [1] – [15] TwrwrDd 設置值有:[Auto] [1] – [15] TrdrdSc 設置值有:[Auto] [1] – [15] TrdrdSd 設置值有:[Auto] [1] – [15] TrdrdDd 設置值有:[Auto] [1] – [15] Tcke 設置值有:[Auto] [1] –
ProcODT 設置值有:[Auto] [High Impedance] [480ohm] [240ohm] [160ohm] [120ohm] [96ohm] [80ohm] [68.6ohm] [60ohm] [53.3ohm] [48ohm] [43.6ohm] [40ohm] [36.9ohm] [34.3ohm] [32ohm] [30ohm] [28.
DIGI+ VRM 數字電源控制 自行變更數值將會導致系統的不穩定與硬件損壞!當系統出現不穩定的狀 況時,建議您使用默認值。 VDDCR CPU Load Line Calibration Load-line 是根據 Intel 所訂立之 VRM 規格,其設置值將影響 CPU 電壓。CPU 運行電壓將依 CPU 的負載呈比例性遞減。當您將此項目的設置值設置越高時, 將可提高電壓值與超頻能力,但會增加 CPU 及 VRM 的溫度。從 1 ~ 5 中選擇 一個級別來調整負載線斜率。 設置值有:[Auto] [Default] [Level 1] - [Level 5] 實際提升的性能視 CPU 型號而異。 請勿移除散熱模塊。散熱環境需受到監控。 VDDCR CPU Current Capability 本項目可讓您設置外部電壓調整器的切斷電流限制。較高的設置將允許電壓調節 器提供更多的電流,而較低的設置將使電壓調節器在所提供的電流高於設置值時 關閉系統。設置值有:[100%] [110%] [120%] [130%] 當超頻或 CPU 負載較高時設置較高的值,以獲得更多的功率支持。 VDDCR CPU Switc
請勿移除散熱模塊。散熱環境需受到監控。 VDDCR SOC Load Line Calibration 設置值有:[Auto] [Level 1] – [Level 5] VDDCR SOC Current Capability 設置值有:[100%] [110%] [120%] [130%] VDDCR SOC Switching Frequency 您可以使用 <+> 與 <-> 鍵調整數值。數值以 50 為間隔,更改的範圍由 200 至 350。 VDDCR SOC Power Phase Control 設置值有:[Optimized] [Extreme] [Manual] 以下項目只有在 VDDCR SOC Power Phase Control 設置為 [Manual] 時 才會出現。 Manual Adjustment 本項目可讓您設置響應時間,選擇 [Regular] 將導致較長的反應時間。 設置值有:[Regular] [Medium] [Fast] [Ultra Fast] VDDCR CPU Voltage 設置值有:[Auto] [Manual] [Offset mode] 以下項目
以下項目只有在 VDDCR SOC Voltage 設置為 [Offset mode] 才會出現。 VDDCR SOC Offset Mode Sign [+] 設置正數值偏移電壓。 [–] 設置負數值偏移電壓。 VDDCR SOC Offset Voltage 設置值有:[Auto] [-0.00625] - [+0.50000] DRAM Voltage 設置值有:[Auto] [1.20] – [1.80] VDDG CCD Voltage Control 設置值有:[Auto] [0.700] – [1.80] VDDG IOD Voltage Control 設置值有:[Auto] [0.700] – [1.80] CLDO VDDP voltage 設置值有:[Auto] [0.700] – [1.80] 1.05V SB Voltage 設置值有:[Auto] [1.05] – [1.1] 2.5V SB Voltage 設置值有:[Auto] [1.05000] – [1.10000] CPU 1.80V Voltage 設置值有:[Auto] [1.80] – [2.
1.
1.6.
1.6.
1.6.3 SATA 設置(SATA Configuration) 當您進入 BIOS 設置程序時,BIOS 設置程序將自動偵測已安裝的 SATA 設備。當未 偵側到 SATA 設備時將顯示【Not Present】。 SATA Port Enable 本項目用來開啟或關閉 SATA 設備。 設置值有:[Disabled] [Enabled] SATA Mode 本項目可設置 SATA 硬件設備的相關設置。 [AHCI] 若要 Serial ATA 硬件設備使用 Advanced Host Controller Interface (AHCI) 模式,請將本項目設置為 [AHCI]。AHCI 模式可讓內置的存 儲設備啟動高級的 Serial ATA 功能,通過原生指令排序技術來提升 工作性能。 [RAID] 若要在 Serial ATA 硬盤設置 RAID 磁盤陣列,請將本項目設置為 [RAID]。 NVMe RAID Mode 本項目用來開啟或關閉 NVMe RAID 模式。 設置值有:[Disabled] [Enabled] SMART Self Test S.M.A.R.T.
SATA6G_1(Gray) - SATA6G_6(Gray) SATA6G_1 - SATA6G_6 本項目用來開啟或關閉選定的 SATA 接口。 設置值有:[Disabled] [Enabled] SATA 端口數量隨主板型號而異。 Hot Plug 這些項目僅當 SATA Mode 設置為 [AHCI] 時才會顯示,並且提供您啟用或關閉 支持 SATA Hot Plug(熱插拔)功能。設置值有:[Disabled] [Enabled] M.2_1(Gray) - M.2_2(Gray) M.2_1 - M.2_2 本項目可讓您重新命名 AMD M.2 插槽。 M.2 插槽數量隨主板型號而異。 1.6.
PCIEX16_1 Mode 本項目用來選擇 PCIEX16_1 插槽的連接速度。 設置值有:[Auto] [Gen 1] [Gen 2] [Gen 3] [Gen 4] M.2_1 Link Mode 本項目用來選擇 M.
板端有無 2.
1.6.
1.6.6 PCI 子系統設置(PCI Subsystem Setting) 本菜單中的項目可用來進行 PCI、PCI-X 與 PCI Express 設置。 SR-IOV Support 當系統有支持 SR-IOV 的 PCIe 設備時,本項目可用來開啟或關閉單個 Root IO 的虛 擬化支持。設置值有:[Disabled] [Enabled] 1.6.
USB Single Port Control 本項目用來開啟或關閉個別 USB 接口。 USB 接口的位置請參考“主板結構圖”的說明。 1.6.8 網絡協議堆棧設置(Network Stack Configuration) 本菜單中的項目用來啟動或關閉 UEFI 網絡協議堆棧(network stack)功能 Network stack 本項目用來開啟或關閉 UEFI 網絡堆棧。 設置值有:[Disable] [Enable] 以下的項目只有在 Network Stack 設置為 [Enabled] 時才會出現。 Ipv4/Ipv6 PXE Support 本項目可讓您開啟或關閉 Ipv4/Ipv6 PXE 喚醒事件。 設置值有:[Disabled] [Enabled] 1.6.
1.6.10 NVMe 設置(NVMe Configuration) 本菜單顯示所連接設備的 NVMe 控制器與磁盤信息。 1.6.
IOMMU 設置值有:[Auto] [Disabled] [Enabled] PCIe ARI Support 設置值有:[Auto] [Disabled] [Enabled] PCIe Ten Bit Tag Support 設置值有:[Auto] [Disabled] [Enabled] 1.6.
Legacy/Native/RTD3 本項目可讓您選擇 Thunderbolt legacy/native/RTD3 模式。 設置值有:[Legacy Mode] [Native Mode] [Native + RTD3Hot] [Native + RTD3Cold] Thunderbolt Wake Up Command 本項目可讓您選擇 Thunderbolt 喚醒命令。 設置值有:[Disabled] [GO2SX Command] [GO2SX_NO_WAKE Command] 以下項目是否出現取決於所安裝的處理器型號。 Data Link Feature Exchange 本項目讓您開啟或關閉 Data Link Feature Exchange 功能。若有任何 Legacy 終端設 備無法啟動,則關閉此項目。設置值有:[Disabled] [Enabled] 1.6.
1.
Q-fan Configuration Q-fan Tuning 點擊本項目會自動偵測最低速度並設置每個風扇的最小工作週期。 CPU Q-Fan Control 本項目可讓您設置 CPU Q-Fan 運行模式。 [Auto] 偵測安裝的處理器風扇類型並自動切換控制模式。 [PWM Mode] 此模式中開啟對 4-pin 處理器風扇的 PWM 模式 Q-Fan 控制。 [DC Mode] 此模式中開啟對 3-pin 處理器風扇的 DC 模式 Q-Fan 控制。 [Disabled] 關閉 Q-Fan 控制。 以下項目只有在 CPU Q-Fan Control 項目設置為 [Auto]、[PWM Mode] 及 [DC Mode] 時才會出現。 CPU Fan Step Up/Down 本項目用來設置 CPU 風扇的加速/減速。 設置值有:[0 sec] [2.1 sec] [2.8 sec] [3.6 sec] [4.2 sec] [5.0 sec] [6.3 sec] [8.
CPU Middle Temperature 使用 <+> / <-> 鍵調整處理器中間溫度。 CPU Fan Middle. Duty Cycle(%) 使用 <+> / <-> 鍵調整處理器風扇中間占空比。 CPU Lower Temperature 使用 <+> / <-> 鍵調整處理器溫度下限。當處理器溫度低於下限時, 處理器風扇會以最小占空比運行。 CPU Fan Min.
Chassis Fan 1-3 Profile 本項目用來為機箱風扇設置適當的性能等級。 [Standard] 設置為 [Standard] 讓機箱風扇根據機箱的溫度自動調整。 [Silent] 設置為 [Silent] 將機箱風扇速度調整到最低,並擁有最安靜的運 行環境。 [Turbo] 設置為 [Turbo] 來獲得機箱風扇的最大轉速。 [Manual] 設置為 [Manual] 可指定詳細的風扇速度控制參數。 以下項目只有在 Chassis Fan 1-3 Profile 設置為 [Manual] 時才會出現。 Chassis Fan 1-3 Upper Temperature 使用 <+> 或 <-> 鍵調整機箱風扇 1-3 溫度的上限。當溫度源高於上 限時,機箱風扇 1-3 將以最大占空比運行。 Chassis Fan 1-3 Max.
AIO PUMP Control [Disabled] 關閉 AIO PUMP 控制功能。 [Auto] 偵測安裝的 AIO PUMP 類型並自動切換控制模式。 [DC mode] 啟動對 3-pin AIO PUMP 風扇的 DC 模式控制。 [PWM mode] 啟動對 4-pin AIO PUMP 風扇的 PWM 模式控制。 以下項目只有在 AIO Pump Control 項目設置為 [Auto]、[DC mode] 或 [PWM mode] 時才會出現。 AIO Pump Upper Temperature 使用 <+> 或 <-> 鍵調整 AIO Pump 溫度的上限。 AIO Pump Max. Duty Cycle (%) 使用 <+> / <-> 鍵調整 AIO Pump 最大占空比。當處理器溫度達到上 限時,AIO Pump 將以最大占空比運行。 AIO Pump Middle Temperature 使用 <+> 或 <-> 鍵調整 AIO Pump 的中間溫度。 AIO Pump Middle.
1.
Boot up NumLock State 本項目用來設置開機時 NumLock 鍵的狀態。 設置值有:[On] [Off] Wait For ‘F1’ If Error 系統開機過程出現錯誤信息時,本項目可讓系統等待您按下 鍵確認才會繼續進 行開機程序。 Option ROM Messages [Force BIOS] 在啟動過程中,第三方 ROM 信息將會強制顯示。 [Keep Current] 只有當第三方廠商將設備設置為顯示 ROM 信息時,第三方 ROM 信 息才會顯示。 Interrupt 19 Capture [Enabled] 立即執行陷阱(trap)。 [Disabled] 在傳統啟動過程中執行陷阱(trap)。 AMI Native NVMe Driver Support 本項目用來開啟或關閉所有 NVMe 設備的原生 OpROM。 設置值有:[On] [Off] Setup Mode [Advanced Mode] 本項目讓您在 POST 後進入 BIOS 的 Advanced Mode。 [EZ Mode] 本項目讓您在 POST 後進入 BIO
Boot from Storage Devices 本項目用來選擇想要運行的存儲設備類型。 設置值有:[Ignore] [Legacy only] [UEFI driver first] Boot from PCI-E/PCI Expansion Devices 本項目用來選擇想要執行的 PCI-E/PCI 擴展設備類型。 設置值有:[Ignore] [Legacy only] [UEFI only] Secure Boot 本項目用來設置 Windows 安全啟動的相關參數以及管理系統密鑰,以提升系統在開機 自檢(POST)時的安全性,避免受到未授權的用戶與惡意軟件的危害。 OS Type [Windows UEFI Mode] 本項目用來選擇您所安裝的操作系統。運行 Microsoft® 安 全啟動檢查。只有在 Windows UEFI 模式或其他 Microsoft 安全啟動兼容操作系統中啟動時選擇此項目。 [Other OS] 在 Windows® 非 UEFI 模式操作系統中啟動時獲得最佳功 能。Microsoft 安全啟動僅支持 Windows UEFI 模式。 Key Manageme
KEK Management KEK(金鑰交換金鑰)用來管理簽名數據庫(db)與撤銷簽名數據庫(dbx)。 Key-exchange Key(KEK)為 Microsoft® Secure Boot Key-Enrollment Key(KEK)。 Save to file 本項目可讓你將 KEK 保存到 USB 存儲設備。 Set New key 本項目用來由 USB 存儲設備載入 KEK。 Append Key 本項目用來設置由存儲設備下載其他 KEK 以管理 db 和 dbx。 Delete key 本項目用來刪除系統中的 KEK。 設置值有:[Yes] [No] KEK 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 DB Management db(Authorized Signature database)包含授權認證和數字簽章等,可載入後 運行。 Save to file 本項目可讓你將 db 保存到 USB 存儲設備。 Set New key 本項目用來由 USB 存儲設備載入已下載的 db。 Append Key 本項目用來設置由存儲設備下載其他 db 以管理 db 和 dbx
Set New key 本項目用來由 USB 存儲設備載入已下載的 dbx。 Append Key 本項目用來由 USB 存儲設備下載其他 dbx 以管理 db 和 dbx。 Delete key 本項目用來刪除系統中的 dbx 文件。 設置值有:[Yes] [No] dbx 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 Boot Option Priorities 本項目讓您自行選擇啟動磁盤並排列啟動設備順序。屏幕上顯示的設備項目數量將視 系統中安裝的設備數量而定。 • 欲進入 Windows® OS 安全模式時,請在開機自檢(POST)時按下 (Windows® 8 不支持這項功能)。 • 開機時您可以在 ASUS Logo 出現時按下 選擇啟動設備。 Boot Override 這些項目將顯示可使用的設備。屏幕上顯示的設備項目數量將視系統中安裝的設備數 量而定。點擊任一設備可將該設備設置為啟動設備。 PRIME/PRO/ProArt/TUF GAMING B550/A520 系列 BIOS 用戶手冊 47
1.9 工具菜單(Tool) 本工具菜單可以讓您針對特別功能進行設置。請選擇菜單中的選項並按下 鍵 來顯示子菜單。 1.9.1 ASUS EZ Flash 3 Utility 本項目可以讓您啟動華碩 EZ Flash 3 程序, 按下 會出現再次確認的窗口, 請使用左右方向鍵選擇 [Yes] 或 [No],接著按下 確認。 請參考"1.11.2 華碩 EZ Flash 3"的說明。 1.9.
狀態說明: • Frozen:當選取的硬盤狀態為 Frozen 時,不能執行安全清除。若要移 除鎖定,應對 SSD 執行一次開機循環。通過將硬盤先拔除後再插入即 可完成此操作。 • Locked:為避免無法順利於 SSD 執行安全清除,在執行安全清除時, 請先解開已由華碩設置密碼的第三方軟件(Third-party software)。 1.9.
1.10 退出 BIOS 程序(Exit) 本菜單可讓您讀取 BIOS 程序出廠默認值與退出 BIOS 程序。你也可以由 Exit 菜單進 入 EZ Mode。 Load Optimized Defaults 本項目可讓您載入 BIOS 程序設置菜單中每個參數的默認值。當您選擇本項目或按下 ,便會出現一個確認對話窗口。選擇【OK】以載入默認值。 Save Changes & Reset 當您完成對 BIOS 設置程序所做的變更後,本項目用來保存您所做的設置。當您選擇 本項目或按下 ,便會出現一個確認對話窗口。請選擇【OK】以保存設置並退 出 BIOS 設置程序。 Discard Changes & Exit 本項目可讓您放棄所做的變更,並恢復原先保存的設置。在選擇本項目或按下 鍵後,將會出現一個確認對話窗口。請選擇【Yes】以放棄任何設置並載入原先保存 的設置,同時退出 BIOS 設置程序。 Launch EFI Shell from USB drives 本項目可以讓您由含有數據系統的設備中啟動 EFI Shell 應用程序(shellx64.
1.11 更新 BIOS 程序 華碩網站上提供有最新的 BIOS 程序,可以強化系統的穩定度、兼容性或執行性能, 但 是執行 BIOS 程序更新是具有潛在性風險的,若是使用現有版本的 BIOS 程序都沒有發 生問題時,請勿手動執行更新 BIOS 程序。不適當的 BIOS 程序更新可能會導致系統開 機失敗。若有需要,請使用以下各節的方法來更新您的 BIOS 程序。 請訪問華碩網站(https://www.asus.com.cn/support)來下載本主板最 新的 BIOS 程序。 下列應用程序可讓您管理或更新主板的 BIOS 設置程序:。 1. EZ Update:在 Windows 操作系統中更新 BIOS 程序。 2. ASUS EZ Flash 3:使用 USB 閃存盤來更新 BIOS。 3. ASUS CrashFree BIOS 3:當 BIOS 文件丟失或損壞時,可以使用 USB 閃存盤 或主板的驅動程序與應用程序光盤來更新 BIOS。 1.11.
1.11.2 ASUS EZ Flash 3 華碩 EZ Flash 3 程序讓您能輕鬆地更新 BIOS 程序,可以不必再到操作系統模式下 執行。 請讀取出廠默認值來保持系統的穩定。在【Exit】菜單中選擇 【Load Optimized Defaults】項目或按下 快捷鍵來恢復 BIOS 默認設置。 請按照以下步驟通過 USB 更新 BIOS 程序: • 本功能僅支持採用 FAT 32/16 格式的單一磁區 USB 閃存盤。 • 當進行 BIOS 更新時,請勿關閉或重新啟動系統以免造成系統開機失 敗! 52 1. 將保存有最新 BIOS 文件的 USB 閃存盤插入 USB 接口。 2. 進入 BIOS 設置程序的 Advanced Mode, 選擇【Tool】>【ASUS EZ Flash 3 Utility】,接著請按下 鍵。 3. 選擇【via Storage Device】。 4. 按 鍵切換到【Drive】區域。 5. 按上/下方向鍵找到保存有最新 BIOS 文件的 USB 閃存盤,然後按下 <Enter> 鍵。 6.
1.11.3 ASUS CrashFree BIOS 3 華碩最新自行研發的 CrashFree BIOS 3 工具程序,讓您在當 BIOS 程序和數據被病 毒入侵或丟失時,可以輕鬆的從含有最新或原始的 BIOS 文件的 U 盤中恢復 BIOS 程 序的數據。 若是想要使用更新的 BIOS 程序,請至 https://www.asus.com.cn/support/ 網站下載,並保存在便攜式存儲設備中。 恢復 BIOS 程序: 請依照下列步驟恢復 BIOS 程序: 1. 啟動系統。 2. 將保存有 BIOS 文件的 USB 閃存盤插入 USB 接口。 3. 接著工具程序便會自動檢查設備中是否存有 BIOS 文件。當搜索到 BIOS 文件後, 工具程序會開始讀取 BIOS 文件並自動進入 EZ Flash 3 應用程序。 4.