Motherboard PRIME/PRO/ ProArt/TUF GAMING B550/A520 系列 BIOS 使用手冊
T16863 第一版 2020 年 7 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
Offer to Provide Source Code of Certain Software This product contains copyrighted software that is licensed under the General Public License (“GPL”), under the Lesser General Public License Version (“LGPL”) and/or other Free Open Source Software Licenses. Such software in this product is distributed without any warranty to the extent permitted by the applicable law. Copies of these licenses are included in this product.
目錄 1.1 認識 BIOS 程式................................................................................................................ 5 1.2 BIOS 設定程式.................................................................................................................. 6 EZ Mode.......................................................................................................... 7 1.2.2 Advanced Mode............................................................................................. 8 1.2.
BIOS 程式設定 1.
1.
1.2.
1.2.
功能表列 BIOS 設定程式最上方各選單功能說明如下: My Favorites 本項目將記錄時常使用的系統設定及設定值。 Main 本項目提供系統基本設定。 Ai Tweaker 本項目提供超頻設定。 Advanced 本項目提供系統進階功能設定。 Monitor 本項目提供溫度、電源及風扇功能設定。 Boot 本項目提供開機磁碟設定。 Tool 本項目提供特殊功能設定。 Exit 本項目提供離開 BIOS 設定程式與出廠預設值還原功能。 選單項目 於功能表列選定選項時,被選擇的功能將會反白,即可選擇 Main 選單所出現的項目。 點選選單中的其他項目(例如:My Favorite、Ai Tweaker、Advanced、Monitor、Boot、Tool 與 Exit)也會出現該項目各自不同的選項。 子選單 在選單畫面中,若功能選項前面有一個小三角形標記(>),代表此為子選單,您可利 用方向鍵來選擇,並按下 鍵來進入子選單。 語言 這個按鈕位在功能表列的上方,用來選擇 BIOS 程式介面顯示的語言。點選這個按鈕 來選擇您想要的 BIOS 畫面顯示語言。
AURA 開關(F4) 這個按鈕用來開啟或關閉 RGB LED 指示燈或功能性 LED 指示燈。 [All On]: 所有指示燈(Aura 及功能性指示燈)將開啟。 [Aura Only]: Aura 指示燈將開啟,而功能性指示燈將關閉。 [Aura Off]: Aura 指示燈將關閉,而功能性指示燈仍然開啟。 [Stealth Mode]: 所有指示燈(Aura 及功能性指示燈)將關閉。 快速鍵 這個按鈕包含有 BIOS 程式設定的導引方向鍵,使用導引方向鍵來選擇選單中的項目 並變更設定。 捲軸 在選單畫面的右方若出現捲軸,即代表此頁選項超過可顯示的畫面,您可利用上/下方 向鍵或是 / 按鍵來顯示畫面中的其他項目。 項目說明 在選單畫面的下方為目前所選擇的作用選項的功能說明,此說明會依選項的不同而自動 變更。使用 按鍵來抓取 BIOS 螢幕畫面,並儲存至攜帶式儲存裝置。 設定視窗 此區域顯示選單項目的設定值。若項目是使用者可以設定的,您可以變更該項目的數 值;若是無法設定,則無法選取該項目。 設定值被選擇後會以反白顯示。要改變設定值請選擇此
1.2.
手動設定風扇 從設定檔清單中選擇 Manual 來手動設定風扇運作的速度。 速度點 點選以手動設定風扇 請依照以下步驟設定風扇: 12 1. 選擇想要設定的風扇並查看該風扇現在的狀況。 2. 點選並拖曳速度點來調整風扇的運作速度。 3.
1.
新增項目至我的最愛 請依照以下步驟新增項目至我的最愛: 1. 在鍵盤按下 鍵或在 BIOS 程式畫面中點選 圖畫面。 2. 在設定樹狀圖畫面中選擇想要儲存至我的最愛的 BIOS 項目。 來啟動設定樹狀 主選單面板 已選擇的捷徑 項目 子選單面板 刪除所有 最愛項目 點選以回復 變更 3. 從主選單面板選擇項目,然後點選子選單中想要儲存至我的最愛的選項,再點選 或輕觸 或是按下 按鍵。 以下項目無法加入至我的最愛: • 有子選單的項目。 • 使用者自訂項目,例如:語言、開機裝置順序。 • 設定項目,例如:記憶體 SPD 資訊、系統時間與日期。 14 4. 點選 Exit (ESC) 或按下 鍵來關閉樹狀圖視窗。 5.
1.
系統管理員密碼(Administrator Password) 當您設定系統管理員密碼後,建議您先登入系統管理員帳戶,以免 BIOS 設定程式中 的某些資訊無法檢視或變更設定。 設定系統管理員密碼 請依照以下步驟設定系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成按下 。 3. 請再一次輸入密碼以確認密碼正確。 變更系統管理員密碼 請依照以下步驟變更系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 視窗輸入密碼並按下 。 3. 由 Create New Password 視窗輸入新密碼,輸入完成按下 。 4.
1.5 Ai Tweaker 選單(Ai Tweaker) 本選單可讓您設定超頻功能的相關選項。 請注意在您變更 Ai Tweaker 選單的設定時,不正確的數值將導致系統功 能異常。 以下項目的預設值會隨著您的主機板型號以及所安裝的處理器與記憶體 型號而不同。 將捲軸往下捲動來顯示以下項目。 Ai Overclock Tuner 本項目可以讓您設定 CPU 的超頻選項來達到您所想要的 CPU 內頻。設定值有: [Auto] 載入系統最佳化設定值。 [Manual] 讓您個別設定超頻比值。 以下項目只有在 Ai Overclock Tuner 設定為 [Manual] 時才會出現。 BCLK Frequency 本項目用來設定 BCLK 頻率以增強系統效能。您可以使用 <+> 與 <-> 鍵調整數 值。數值變更的範圍為 96.0MHz 至 118.
Memory Frequency 本項目可讓您設定記憶體的運作頻率。設定選項會隨著 BCLK(基礎時鐘)頻率的設 定值變動。選擇自動模式以套用最佳化設定。設定值有:[Auto] [DDR4-1333MHz] – [DDR4-6000MHz] 設定過高的記憶體頻率將會導致系統的不穩定與硬體毀損, 當系統出現不 穩定的狀況時,建議您使用預設值。 FCLK Frequency 本項目用來指定 FCLK 頻率。 設定值有:[Auto] [666MHz] [800MHz] – [3000MHz] CPU Core Ratio 本項目用來設定處理器核心倍頻。您可以使用 <+> 與 <-> 鍵調整數值。設定值取決於 安裝的處理器。 CPU Core Ratio (Per CCX) Core VID 本項目用來設定自定義處理器核心 VID。您可以使用 <+> 與 <-> 鍵調整數值。數 值變更的範圍為 0.700 至 1.550。 CCX0/1 Ratio 本項目用來為此 CCX 設定自定義的核心倍頻。您可以使用 <+> 與 <-> 鍵調整數 值。數值變更的範圍為 28.00 至 63.
Max CPU Boost Clock Override 本項目可讓您透過 Precision Boost 2 算法自動增加最大處理器頻率值。設定值 有:[Auto] [0MHz] [25MHz] [75MHz] [100MHz] [125MHz] [150MHz] [175MHz] [200MHz] Platform Thermal Throttle Limit 本項目可用來降低允許的最高處理器溫度(攝氏度)。設定值有:[Auto] [Manual] DRAM Timing Control 本選單中的項目可讓您設定記憶體時序控制功能。您可以使用 <+> 與 <-> 鍵調整數值。 當您要回復預設值時,請使用鍵盤輸入 [auto] 並按下 鍵。 自行變更數值將會導致系統的不穩定與硬體損毀!當系統出現不穩定的狀 況時,建議您使用預設值。 DRAM CAS# Latency 設定值有:[Auto] [5] – [33] Trcdrd 設定值有:[Auto] [8] – [27] Trcdwr 設定值有:[Auto] [8] – [27] DRAM RAS# PRE Time 設定值有:[Auto]
Trcpage 設定值有:[Auto] [0] -[1023] TrdrdScl 設定值有:[Auto] [1] – [15] TwrwrScl 設定值有:[Auto] [1] – [63] Trfc 設定值有:[Auto] [60] – [1023] Trfc2 設定值有:[Auto] [60] – [1023] Trfc4 設定值有:[Auto] [60] – [990] Tcwl 設定值有:[Auto] [9] – [22] Trtp 設定值有:[Auto] [5] – [14] Trdwr 設定值有:[Auto] [1] – [31] Twrrd 設定值有:[Auto] [1] – [15] TwrwrSc 設定值有:[Auto] [1] – [15] TwrwrSd 設定值有:[Auto] [1] – [15] TwrwrDd 設定值有:[Auto] [1] – [15] TrdrdSc 設定值有:[Auto] [1] – [15] TrdrdSd 設定值有:[Auto] [1] – [15] TrdrdDd 設定值有:[Auto] [1] – [15] Tcke 設定值有:[Auto] [1] –
Cmd2T 設定值有:[Auto] [1T] [2T] Gear Down Mode 設定值有:[Auto] [Enabled] [Disabled] Power Down Enable 設定值有:[Auto] [Enabled] [Disabled] RttNom 設定值有:[Auto] [Rtt_Nom Disable] [RZQ/4] [RZQ/2] [RZQ/6] [RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] RttWr 設定值有:[Auto] [Dynamic ODT Off] [RZQ/2] [RZQ/1] [Hi-Z] [RZQ/3] RttPark 設定值有:[Auto] [Rtt_PARK Disable] [RZQ/4] [RZQ/2] [RZQ/6] [RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] MemAddrCmdSetup 設定值有:[Auto] [0]-[63] MemCsOdtSetup 設定值有:[Auto] [0]-[63] MemCkeSetup 設定值有:[Auto] [0]-[63] MemCadBusClkDrvStren 設定值有
DIGI+ VRM 數位電源控制 自行變更數值將會導致系統的不穩定與硬體損毀!當系統出現不穩定的狀 況時,建議您使用預設值。 VDDCR CPU Load Line Calibration Load-line 是依據 Intel 所訂立之 VRM 規格,其設定值將影響 CPU 電壓。CPU 運作電壓將依 CPU 的負載呈比例性遞減。當您將此項目的設定值設定越高時, 將可提高電壓值與超頻能力,但會增加 CPU 及 VRM 的溫度。從 1 ~ 5 中選擇一 個級別來調整負載線斜率。 設定值有:[Auto] [Default] [Level 1] - [Level 5] 實際提升的效能視 CPU 型號而異。 請勿移除散熱模組。散熱環境需受到監控。 VDDCR CPU Current Capability 本項目可讓您設定外部電壓調整器的切斷電流限制。較高的設定將允許電壓調節 器提供更多的電流,而較低的設定將使電壓調節器在所提供的電流高於設定值時 關閉系統。設定值有:[100%] [110%] [120%] [130%] 當超頻或 CPU 負載較高時設定較高的值,以獲得更多的功率支援。 VDDCR CPU Switc
請勿移除散熱模組。散熱環境需受到監控。 VDDCR SOC Load Line Calibration 設定值有:[Auto] [Level 1] – [Level 5] VDDCR SOC Current Capability 設定值有:[100%] [110%] [120%] [130%] VDDCR SOC Switching Frequency 您可以使用 <+> 與 <-> 鍵調整數值。數值以 50 為間隔,更改的範圍由 200 至 350。 VDDCR SOC Power Phase Control 設定值有:[Optimized] [Extreme] [Manual] 以下項目只有在 VDDCR SOC Power Phase Control 設定為 [Manual] 時 才會出現。 Manual Adjustment 本項目可讓您設定響應時間,選擇 [Regular] 將導致較長的反應時間。 設定值有:[Regular] [Medium] [Fast] [Ultra Fast] VDDCR CPU Voltage 設定值有:[Auto] [Manual] [Offset mode] 以下項目
VDDCR SOC Offset Mode Sign [+] 設定正數值偏移電壓。 [–] 設定負數值偏移電壓。 VDDCR SOC Offset Voltage 設定值有:[Auto] [-0.00625] - [+0.50000] DRAM Voltage 設定值有:[Auto] [1.20] – [1.80] VDDG CCD Voltage Control 設定值有:[Auto] [0.700] – [1.80] VDDG IOD Voltage Control 設定值有:[Auto] [0.700] – [1.80] CLDO VDDP voltage 設定值有:[Auto] [0.700] – [1.80] 1.05V SB Voltage 設定值有:[Auto] [1.05] – [1.1] 2.5V SB Voltage 設定值有:[Auto] [1.05000] – [1.10000] CPU 1.80V Voltage 設定值有:[Auto] [1.80] – [2.
1.
1.6.
1.6.
1.6.3 SATA 設定(SATA Configuration) 當您進入 BIOS 設定程式時,BIOS 設定程式將自動偵測已安裝的 SATA 裝置。當未偵 側到 SATA 裝置時將顯示 Not Present。 SATA Port Enable 本項目用來開啟或關閉 SATA 裝置。 設定值有:[Disabled] [Enabled] SATA Mode 本項目可設定 SATA 硬體裝置的相關設定。 [AHCI] 若要 Serial ATA 硬體裝置使用 Advanced Host Controller Interface (AHCI) 模式,請將本項目設定為 [AHCI]。AHCI 模式可讓內建的儲 存裝置啟動進階的 Serial ATA 功能,透過原生指令排序技術來提升 工作效能。 [RAID] 若要在 Serial ATA 硬碟設定 RAID 磁碟陣列,請將本項目設定為 [RAID]。 NVMe RAID Mode 本項目用來開啟或關閉 NVMe RAID 模式。 設定值有:[Disabled] [Enabled] SMART Self Test S.M.A.R.T.
SATA6G_1(Gray) - SATA6G_6(Gray) SATA6G_1 - SATA6G_6 本項目用來開啟或關閉選定的 SATA 連接埠。 設定值有:[Disabled] [Enabled] SATA 連接埠數量隨主機板型號而異。 Hot Plug 這些項目僅當 SATA Mode 設定為 [AHCI] 時才會顯示,並且提供您啟用或關閉支 援 SATA Hot Plug(熱插拔)功能。設定值有:[Disabled] [Enabled] M.2_1(Gray) - M.2_2(Gray) M.2_1 - M.2_2 本項目可讓您重新命名 AMD M.2 插槽。 M.2 插槽數量隨主機板型號而異。 1.6.
PCIEX16_1 Mode 本項目用來選擇 PCIEX16_1 插槽的連接速度。 設定值有:[Auto] [Gen 1] [Gen 2] [Gen 3] [Gen 4] M.2_1 Link Mode 本項目用來選擇 M.
板端有無 2.
1.6.
1.6.6 PCI 子系統設定(PCI Subsystem Setting) 本選單中的項目可用來進行 PCI、PCI-X 與 PCI Express 設定。 SR-IOV Support 當系統有支援 SR-IOV 的 PCIe 裝置時,本項目可用來開啟或關閉單個 Root IO 的虛擬 化支援。設定值有:[Disabled] [Enabled] 1.6.
USB Single Port Control 本項目用來開啟或關閉個別 USB 連接埠。 USB 連接埠的位置請參考 主機板結構圖 的說明。 1.6.8 網路協定堆疊設定(Network Stack Configuration) 本選單中的項目用來啟動或關閉 UEFI 網路協定堆疊(network stack)功能。 Network stack 本項目用來開啟或關閉 UEFI 網路堆疊。 設定值有:[Disable] [Enable] 以下的項目只有在 Network Stack 設定為 [Enabled] 時才會出現。 Ipv4/Ipv6 PXE Support 本項目可讓您開啟或關閉 Ipv4/Ipv6 PXE 喚醒事件。 設定值有:[Disabled] [Enabled] 1.6.
1.6.10 NVMe 設定(NVMe Configuration) 本選單顯示所連接裝置的 NVMe 控制器與磁碟資訊。 1.6.
IOMMU 設定值有:[Auto] [Disabled] [Enabled] PCIe ARI Support 設定值有:[Auto] [Disabled] [Enabled] PCIe Ten Bit Tag Support 設定值有:[Auto] [Disabled] [Enabled] 1.6.
Legacy/Native/RTD3 本項目可讓您選擇 Thunderbolt legacy/native/RTD3 模式。 設定值有:[Legacy Mode] [Native Mode] [Native + RTD3Hot] [Native + RTD3Cold] Thunderbolt Wake Up Command 本項目可讓您選擇 Thunderbolt 喚醒命令。 設定值有:[Disabled] [GO2SX Command] [GO2SX_NO_WAKE Command] 以下項目是否出現取決於所安裝的處理器型號。 Data Link Feature Exchange 本項目讓您開啟或關閉 Data Link Feature Exchange 功能。若有任何 Legacy 終端裝置 無法啟動,則關閉此項目。設定值有:[Disabled] [Enabled] 1.6.
1.
Q-fan Configuration Q-fan Tuning 點選本項目會自動偵測最低速度並設定每個風扇的最小工作週期。 CPU Q-Fan Control 本項目可讓您設定 CPU Q-Fan 運作模式。 [Auto] 偵測安裝的處理器風扇類型並自動切換控制模式。 [PWM Mode] 此模式中開啟對 4-pin 處理器風扇的 PWM 模式 Q-Fan 控制。 [DC Mode] 此模式中開啟對 3-pin 處理器風扇的 DC 模式 Q-Fan 控制。 [Disabled] 關閉 Q-Fan 控制。 以下項目只有在 CPU Q-Fan Control 項目設定為 [Auto]、[PWM Mode] 及 [DC Mode] 時才會出現。 CPU Fan Step Up/Down 本項目用來設定 CPU 風扇的加速/減速。 設定值有:[0 sec] [2.1 sec] [2.8 sec] [3.6 sec] [4.2 sec] [5.0 sec] [6.3 sec] [8.
CPU Middle Temperature 使用 <+> / <-> 鍵調整處理器中間溫度。 CPU Fan Middle. Duty Cycle(%) 使用 <+> / <-> 鍵調整處理器風扇中間占空比。 CPU Lower Temperature 使用 <+> / <-> 鍵調整處理器溫度下限。當處理器溫度低於下限時,處 理器風扇會以最小占空比運作。 CPU Fan Min.
Chassis Fan 1-3 Profile 本項目用來為機殼風扇設定適當的效能等級。 [Standard] 設定為 [Standard] 讓機殼風扇依據機殼的溫度自動調整。 [Silent] 設定為 [Silent] 將機殼風扇速度調整到最低,並擁有最安靜的運 作環境。 [Turbo] 設定為 [Turbo] 來獲得機殼風扇的最大轉速。 [Manual] 設定為 [Manual] 可指定詳細的風扇速度控制參數。 以下項目只有在 Chassis Fan 1-3 Profile 設定為 [Manual] 時才會出現。 Chassis Fan 1-3 Upper Temperature 使用 <+> 或 <-> 鍵調整機殼風扇 1-3 溫度的上限。當溫度源高於上限 時,機殼風扇 1-3 將以最大占空比運作。 Chassis Fan 1-3 Max.
AIO PUMP Control [Disabled] 關閉 AIO PUMP 控制功能。 [Auto] 偵測安裝的 AIO PUMP 類型並自動切換控制模式。 [DC mode] 啟動對 3-pin AIO PUMP 風扇的 DC 模式控制。 [PWM mode] 啟動對 4-pin AIO PUMP 風扇的 PWM 模式控制。 以下項目只有在 AIO Pump Control 項目設定為 [Auto]、[DC mode] 或 [PWM mode] 時才會出現。 AIO Pump Upper Temperature 使用 <+> 或 <-> 鍵調整 AIO Pump 溫度的上限。 AIO Pump Max. Duty Cycle (%) 使用 <+> / <-> 鍵調整 AIO Pump 最大占空比。當處理器溫度達到上限 時,AIO Pump 將以最大占空比運作。 AIO Pump Middle Temperature 使用 <+> 或 <-> 鍵調整 AIO Pump 的中間溫度。 AIO Pump Middle.
1.
Boot up NumLock State 本項目用來設定開機時 NumLock 鍵的狀態。 設定值有:[On] [Off] Wait For ‘F1’ If Error 系統開機過程出現錯誤資訊時,本項目可讓系統等待您按下 鍵確認才會繼續進 行開機程式。 Option ROM Messages [Force BIOS] 在啟動過程中,第三方 ROM 資訊將會強制顯示。 [Keep Current] 只有當第三方廠商將裝置設定為顯示 ROM 資訊時,第三方 ROM 資訊 才會顯示。 Interrupt 19 Capture [Enabled] 立即執行陷阱(trap)。 [Disabled] 在傳統啟動過程中執行陷阱(trap)。 AMI Native NVMe Driver Support 本項目用來開啟或關閉所有 NVMe 裝置的原生 OpROM。 設定值有:[On] [Off] Setup Mode [Advanced Mode] 本項目讓您在 POST 後進入 BIOS 的 Advanced Mode。 [EZ Mode] 本項目讓您在 POST 後進入 BI
Boot from Storage Devices 本項目用來選擇想要運作的儲存裝置類型。 設定值有:[Ignore] [Legacy only] [UEFI driver first] Boot from PCI-E/PCI Expansion Devices 本項目用來選擇想要執行的 PCI-E/PCI 擴充裝置類型。 設定值有:[Ignore] [Legacy only] [UEFI only] Secure Boot 本項目用來設定 Windows 安全啟動的相關參數以及管理系統金鑰,以提升系統在開機 自我測試(POST)時的安全性,避免受到未授權的使用者與惡意軟體的危害。 OS Type [Windows UEFI Mode] 本項目用來選擇您所安裝的作業系統。運作 Microsoft® 安全 啟動檢查。只有在 Windows UEFI 模式或其他 Microsoft 安 全啟動相容作業系統中啟動時選擇此項目。 [Other OS] 在 Windows® 非 UEFI 模式作業系統中啟動時獲得最佳功 能。Microsoft 安全啟動僅支援 Windows UEFI 模式。 Key Mana
KEK Management KEK(金鑰交換金鑰)用來管理簽名資料庫(db)與撤銷簽名資料庫(dbx)。 Key-exchange Key(KEK)為 Microsoft® Secure Boot Key-Enrollment Key(KEK)。 Save to file 本項目可讓你將 KEK 儲存到 USB 儲存裝置。 Set New key 本項目用來由 USB 儲存裝置載入 KEK。 Append Key 本項目用來設定由儲存裝置下載其他 KEK 以管理 db 和 dbx。 Delete key 本項目用來刪除系統中的 KEK。 設定值有:[Yes] [No] KEK 檔案必須格式化為一個以時間認證變量為基礎的 UEFI 變量結構。 DB Management db(Authorized Signature database)包含授權認證和數位簽章等,可載入後運作。 Save to file 本項目可讓你將 db 儲存到 USB 儲存裝置。 Set New key 本項目用來由 USB 儲存裝置載入已下載的 db。 Append Key 本項目用來設定由儲存裝置下載其他 db 以管理 db 和 db
Set New key 本項目用來由 USB 儲存裝置載入已下載的 dbx。 Append Key 本項目用來由 USB 儲存裝置下載其他 dbx 以管理 db 和 dbx。 Delete key 本項目用來刪除系統中的 dbx 檔案。 設定值有:[Yes] [No] dbx 檔案必須格式化為一個以時間認證變量為基礎的 UEFI 變量結構。 Boot Option Priorities 本項目讓您自行選擇啟動磁碟並排列開機裝置順序。螢幕上顯示的裝置項目數量將視 系統中安裝的裝置數量而定。 • 欲進入 Windows® OS 安全模式時,請在開機自我測試(POST)時按 下 (Windows® 8 不支援這項功能)。 • 開機時您可以在 ASUS Logo 出現時按下 選擇開機裝置。 Boot Override 這些項目將顯示可使用的裝置。螢幕上顯示的裝置項目數量將視系統中安裝的裝置數 量而定。點選任一裝置可將該裝置設定為開機裝置。 PRIME/PRO/ProArt/TUF GAMING B550/A520 系列 BIOS 使用手冊 47
1.9 工具選單(Tool) 本工具選單可以讓您針對特別功能進行設定。請選擇選單中的選項並按下 鍵 來顯示子選單。 1.9.1 ASUS EZ Flash 3 Utility 本項目可以讓您啟動華碩 EZ Flash 3 程式, 按下 會出現再次確認的視窗,請 使用左右方向鍵選擇 [Yes] 或 [No],接著按下 確認。 請參考 1.11.2 華碩 EZ Flash 3 的說明。 1.9.
狀態說明: • Frozen:當選取的硬碟狀態為 Frozen 時,不能執行安全清除。若要移 除鎖定,應對 SSD 執行一次開機循環。透過將硬碟先拔除後再插入即 可完成此操作。 • Locked:為避免無法順利於 SSD 執行安全清除,在執行安全清除時, 請先解開已由華碩設定密碼的第三方軟體(Third-party software)。 1.9.
1.10 離開 BIOS 程式(Exit) 本選單可讓您讀取 BIOS 程式出廠預設值與離開 BIOS 程式,並可儲存與取消對 BIOS 項目的變更。你也可以由 Exit 選單進入 EZ Mode。 Load Optimized Defaults 本項目可讓您載入 BIOS 程式設定選單中每個參數的預設值。當您選擇本項目或按下 ,便會出現一個確認對話視窗,選擇 OK 以載入預設值。 Save Changes & Reset 當您完成對 BIOS 設定程式所做的變更後,請選擇本項目或按下 ,將會出現一個 確認對話視窗,請選擇 OK 以儲存設定並離開 BIOS 設定程式。 Discard Changes & Exit 本項目可讓您放棄所做的變更,並回復原先儲存的設定。在選擇本項目或按下 鍵後,將會出現一個確認對話視窗,請選擇 Yes 以放棄任何設定並載入原先儲存的設 定,同時離開 BIOS 設定程式。 Launch EFI Shell from filesystem device 本項目可以讓您由含有資料系統的裝置中啟動 EFI Shell(shellx64.
1.11 更新 BIOS 程式 華碩網站上提供有最新的 BIOS 程式,可以強化系統的穩定度、相容性或執行效能,但 是執行 BIOS 程式更新是具有潛在性風險的,若是使用現有版本的 BIOS 程式都沒有發 生問題時,請勿手動執行更新 BIOS 程式。不適當的 BIOS 程式更新可能會導致系統開 機失敗。若有需要,請使用以下各節的方法來更新您的 BIOS 程式。 請造訪華碩網站(https://www.asus.com.tw/support)來下載本主機板最新 的 BIOS 程式。 1. EZ Update:在 Windows 作業系統中更新 BIOS 程式。 2. ASUS EZ Flash 3:使用 USB 隨身碟來更新 BIOS。 3. ASUS CrashFree BIOS 3:當 BIOS 檔案遺失或損毀時,可以使用 USB 隨身碟或 主機板的驅動程式與公用程式光碟來更新 BIOS。 1.11.
1.11.2 ASUS EZ Flash 3 華碩 EZ Flash 3 程式讓您能輕鬆地更新 BIOS 程式,可以不必再到作業系統模式下執 行。 請讀取出廠預設值來保持系統的穩定。在 Exit 選單中選擇 Load Optimized Defaults 項目或按下 快捷鍵來回復 BIOS 預設設定。 請按照以下步驟透過 USB 更新 BIOS 程式: • 本功能僅支援採用 FAT 32/16 格式的單一磁區 USB 隨身碟。 • 當進行 BIOS 更新時,請勿關閉或重新啟動系統以免造成系統開機失 敗! 52 1. 將儲存有最新 BIOS 檔案的 USB 隨身碟插入 USB 連接埠。 2. 進入 BIOS 設定程式的 Advanced Mode,選擇 Tool > ASUS EZ Flash 3 Utility, 接著請按下 鍵。 3. 選擇 via Storage Device。 4. 按 鍵切換到 Drive 區域。 5. 按上/下方向鍵找到儲存有最新 BIOS 檔案的 USB 隨身碟,然後按下 <Enter> 鍵。 6.
1.11.3 ASUS CrashFree BIOS 3 華碩最新自行研發的 CrashFree BIOS 3 工具程式,讓您在當 BIOS 程式和資料被病毒入 侵或毀損時,可以輕鬆的從驅動程式及公用程式光碟,或是從含有最新或原始的BIOS 檔案的 USB 隨身碟中回復 BIOS 程式的資料。 在驅動程式及公用程式光碟中的 BIOS 程式版本可能會比官方網站上的BIOS 程式版本舊,若是想要使用更新的 BIOS 程式,請至 http://www.asus.com/ support 網站下載,並儲存在可攜式儲存裝置中。 回復 BIOS 程式 請依照下列步驟使用公用程式光碟回復 BIOS 程式: 1. 啟動系統。 2. 將主機板的公用程式光碟放入光碟機,或是將含有最新或原始的 BIOS 檔案的USB 隨身碟插入 USB 連接埠。 3. 接著工具程式便會自動檢查光碟片或儲存裝置中是否存有 BIOS 檔案。當搜尋到 BIOS 檔案後,工具程式會開始讀取 BIOS 檔案並自動進入 ASUS EZ Flash 3 程 式。 4.