BIOS 用戶手冊 Motherboard PRIME / ProArt / TUF GAMING Intel 700 系列
C21967 第三版 2023 年 4 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
目錄 1. 2. 認識 BIOS 程序.............................................................................................................4 BIOS 程序設置..............................................................................................................5 2.1 EZ Mode ....................................................................................................6 2.2 高級菜單(Advanced menu)...........................................................7 2.3 Qfan Control.........................................
BIOS 程序設置 1.
2.
2.
2.
功能表列 BIOS 設置程序最上方各菜單功能說明如下: My Favorites 本項目將記錄時常使用的系統設置及設置值。 Main 本項目提供系統基本設置。 Ai Tweaker 本項目提供超頻設置。 Advanced 本項目提供系統高級功能設置。 Monitor 本項目提供溫度、電源及風扇功能設置。 Boot 本項目提供啟動磁盤設置。 Tool 本項目提供特殊功能設置。 Exit 本項目提供退出 BIOS 設置程序與出廠默認值還原功能。 菜單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功能,則會顯示 Main 菜單的項目。 點擊菜單中的其他項目(例如:My Favories、Ai Tweaker、Advanced、Monitor、Boot、Tool 與 Exit)也會出現該項目不同的選 項。 子菜單 在菜單畫面中,若功能選項前面有一個小三角形標記(>),代表此為子菜單,您可 利用方向鍵來選擇,並按下 鍵來進入子菜單。 語言 這個按鈕位在功能表列的上方,用來選擇 BIOS 程序接口顯示的語言。點擊這個按鈕 來選擇您想要的 BIO
AI OC Guide 這個按鈕位在功能表列的上方,用來查看超頻的敘述並且可以啟動該功能。您也可 以按下 鍵以使用此項目。 • 請參考 AI OC Guide 一節以獲得更多信息。 • 這項功能只有在安裝沒有鎖頻的處理器時才能使用。 • 這項功能僅適用於特定型號。 搜索 (F9) 這個按鈕用來通過輸入名稱搜索 BIOS 項目,輸入名稱可以找到相關的項目列表。您 可以按下 鍵開啟此菜單。 AURA 這個按鈕用來啟動或關閉 Aura 特效或功能性 LED 指示燈。您可以按下 鍵開 啟此菜單。 [All On] 啟動所有的 LED 指示燈(Aura 特效或是功能性指示燈)。 [Stealth Mode] 關閉所有的 LED 指示燈(Aura 特效與功能性指示燈)。 [Aura Only] 啟動 Aura 特效,而功能性指示燈將會關閉。 [Aura Off] 關閉 Aura 特效,而功能性指示燈依舊為開啟狀態。 ReSize BAR 這個按鈕用來啟動或關閉 ReSize BAR 功能。 [On] 啟動 ReSize BAR 支持以充分利用 GPU 內存。CS
項目說明 在菜單畫面的右上方為當前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動更改。使用 按鍵來抓取 BIOS 屏幕畫面,並保存至攜帶式存儲設備。 設置窗口 此區域顯示菜單項目的設置值。這些項目中,有的功能選項僅為告知用戶當前運行 狀態,並無法更改,此類項目就會以淡灰色顯示。而可更改的項目,當您使用方向 鍵移動項目時, 設置值被選擇後以反白顯示。要改變設置值請選擇此項目,並按下 鍵以顯 示設置值列表。 上次修改的設置按鈕 按下此按鈕可查看您在 BIOS 設置中上一次所做的修改項目。 10 PRIME / ProArt / TUF GAMING Intel 700 系列 BIOS 用戶手冊
2.
手動設置風扇 從設置文件清單中選擇 Manual 來手動設置風扇運行的速度。 速度點 點擊或輕觸以手動設置風扇 請依照以下步驟設置風扇: 12 1. 選擇想要設置的風扇並查看該風扇現在的狀況。 2. 點擊並拖曳速度點來調整風扇的運行速度。 3.
2.
3.
添加項目至我的最愛 請依照以下步驟添加項目至我的最愛: 1. 在鍵盤按下 鍵或在 BIOS 程序中點擊 MyFavorite 來啟動設置樹狀圖畫 面。 2. 在設置樹狀圖畫面中選擇想要保存至我的最愛的 BIOS 項目。 主菜單面板 選擇快捷方式項目 子菜單面板 刪除所有我 的最愛項目 恢復默認值 3. 從主菜單面板選擇項目,然後點擊子菜單中想要保存至我的最愛的選項,再點 擊或輕觸 或是按下 按鍵。 以下項目無法加入至我的最愛: • 有子菜單的項目。 • 用戶自訂項目,例如:語言、啟動設備順序。 • 設置項目,例如:內存 SPD 信息、系統時間與日期。 4. 點擊 Exit (ESC) 或按下 鍵來關閉樹狀圖窗口。 5.
4.
• 若您忘記設置的 BIOS 密碼,可以採用清除 CMOS 實時鐘(RTC)內存。請 參考主板用戶手冊中的相關說明以了解 Clear CMOS 按鈕並清除 CMOS 實時 時鐘(RTC)內存數據。 • Administrator 或 User Password 項目默認值為 [Not Installed]。當您設置密 碼之後將顯示為 [Installed]。 Administrator Password(設置系統管理員密碼) 當您設置系統管理員密碼後,推薦您先登入您的帳戶,以免 BIOS 設置程序中的某些 信息無法查看或更改設置。 請依照以下步驟設置系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 窗口輸入欲設置的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼並選擇 OK。 請依照以下步驟更改系統管理員密碼(Administrator Password): 1.
5.
以下項目只有在 Ai Overclock Tuner 設為 [Manual]、 [AEMP]、 [XMP I] 或 [XMP II] 時才會出現。 BCLK Frequency 本項目用來設置 BCLK 頻率以增強系統性能。請使用 <+> 與 <-> 鍵調整數值。 建議您依照處理器規格設置數值,設置過高的數值可能造成處理器永久性的損害。 以下項目只有在 Ai Overclock Tuner 設置為 [AEMP] 時才會出現。 AEMP 本項目用來選擇 ASUS Enhanced Memory Profile(AEMP)。每個設置文件都有專 屬動態隨機存取內存(DRAM)頻率、時間與電壓。 以下項目只有在 Ai Overclock Tuner 設置為 [XMP I] 或 [XMP II] 時才會出現。 XMP 本項目用來選擇 Extreme Memory Profile。每個設置文件都有專屬動態隨機存取內 存(DRAM)頻率、時間與電壓。 Intel(R) Adaptive Boost Technology 本項目用來開啟或關閉 IABT 以通過允許更高的多核心頻率來提高性能。當存在電 流、功率與熱餘
BCLK FrequencyDRAM Frequency Ratio [Auto] 自動最佳化 BCLK 頻率與 DRAM 頻率。 [100:133] 本項目將 BCLK 頻率與 DRAM 頻率的比值設為 100:133。 [100:133] 本項目將 BCLK 頻率與 DRAM 頻率的比值設為 100:100。 Memory Controller : DRAM Frequency Ratio BCLK Frequency: DRAM Frequency Ratio 選擇 100:133 時有較好的超頻性能, 同時 1:2 Memory Controller: DRAM Frequency Ratio 僅在 DRAM 比值為偶數時運 作。 設置值有:[Auto] [1:1] [1:2] [1:4] DRAM Frequency 本項目可讓您設置內存的運作頻率。設置選項會隨著 BCLK Frequency 設置值變 動。選擇自動模式以套用最佳化設置。 以下項目中的設置值,可能會隨安裝在主板上的 CPU 與內存條而異。 呈灰色的設置值不建議使用,請使用呈白色的設置值。 OC Tuner OC T
以下項目只有當 Performance Core Ratio 設為 [By Core Usage] 時才會出現。 1-Core Ratio Limit / 2-Core Ratio Limit / 3-Core Ratio Limit / 4-Core Ratio Limit / 5-Core Ratio Limit / 6-Core Ratio Limit N-core 比率限制需高於或等於(N+1)-core 比率限制。(N 代表 CPU 核心數量) 當核心數量低於 N 時,核心比率限制無法設置為 [Auto] 。最大核心比率限制需低 於或等於第二大核心比率限制。請使用 <+> 與 <-> 鍵調整數值。 設置值有:[Auto] [36] - [85] 以下項目只有當 Performance Core Ratio 設為 [AI Optimized] 時才會出現。 Optimized AVX Frequency 標準用例選擇 [Normal Use],或是極端負載如 Prime 95 AVX 時選擇[Heavy AVX] 。 設置值有:[Normal Use] [Heavy AVX] 以下項目只有當 Pe
以下項目只有在 Performance Core0-5 specific Voltage 設為 [Adaptive Mode] 時 才會出現。 Offset Mode Sign [+] 設置正數值偏移電壓。 [-] 設置負數值偏移電壓。 Additional Turbo Mode CPU Core0-5 Voltage 設置在 Turbo 模式下運作時饋送到 CPU 核心的電壓量。設置高 CPU 核心頻 率時增加電壓。該電壓會受到偏移值的影響。請使用 <+> 與 <-> 鍵調整數值。 數值以 0.001V 為間隔,變更的範圍由 0.001V 至 1.920V。 設置值有:[Auto] [0.00100] - [1.92000] Performance Core0-5 Offset 設置 CPU 核心電壓偏移值。請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為間隔,變更的範圍由 0.001V 至 0.999V。設置值有:[Auto] [0.00100] [0.
以下項目只有當 Efficient Core Ratio 設為 [Auto]、[Sync All Cores] 或 [By Core Usage] 時才會出現。 Specific Efficient Core Performance Group0-1 Specific Ratio Limit 為部分性能核心設置比率限制。請使用 <+> 與 <-> 鍵調整數值。 設置值有:[Auto] [8] - [120] Performance Group0-1 specific Voltage 本項目用來設置 CPU 核心的電壓供應。設為 [Auto] 將依據使用的 CPU 核心 比調節電壓。不要將此設置與 VCCIN(CPU 輸入電壓)混淆。 設置值有:[Auto] [Manual Mode] [Adaptive Mode] 以下項目只有在 Efficient Core Group0-1 specific Voltage 設為 [Manual Mode] 時才會出現。 CPU Core-0 Voltage Override / CPU Core-1 Voltage Override 設置 CPU 核心電壓偏移值。請
AVX Related Controls AVX2 啟用或關閉 AVX 2 控制器。 設置值有:[Auto] [Disabled] [Enabled] AVX2 Ratio Offset to per-core Ratio Limit 設置值有:[Auto] [User Specify] 以下項目只有在 AVX2 Ratio Offset to per-core Ratio Limit 設為 [User Specify] 時才會出現。 AVX2 Ratio Offset 指定降低 AVX 比與每個核心比的 bin 數量。AVX 是一個壓力更大的工作負 載,降低 AVX 比率有助於確保 SSE 工作負載的最大可能比。使用 Mailbox MSR 0x150、cmd 0x1B。範圍 0-31。0=無偏移。請使用 <+> 與 <-> 鍵調整 數值。 設置值有:[0] - [31] AVX2 Voltage Guardband Scale Factor 設置值有:[Auto] [User Specify] 以下項目只有在 AVX2 Voltage Guardband Scale Factor 設為 [User Sp
DRAM RAS# ACT Time 設置值有:[Auto] [1] - [511] DRAM Command Rate 設置值有:[Auto] [1N] [2N] [3N] [N:1] 以下項目只有當 DRAM Command Rate 設為 [N:1] 時才會出現。 N to 1 ratio 每個有效命令周期之間的數值。 設定值有:[1] - [7] Secondary Timings DRAM RAS# to RAS# Delay L 設置值有:[Auto] [1] - [63] DRAM RAS# to RAS# Delay S 設置值有:[Auto] [1] - [127] DRAM REF Cycle Time 設置值有:[Auto] [1] - [65535] DRAM REF Cycle Time 2 設置值有:[Auto] [1] - [65535] DRAM REF Cycle Time Same Bank 設置值有:[Auto] [0] - [2047] DRAM Refresh Interval 設置值有:[Auto] [1] - [262143] DRAM WRITE Recove
Ctl0 dqvrefdn 設置值有:[Auto] [0] - [255] Ctl0 dqodtvrefup 設置值有:[Auto] [0] - [255] Ctl0 dqodtvrefdn 設置值有:[Auto] [0] - [255] Ctl1 cmdvrefup 設置值有:[Auto] [0] - [255] Ctl1 ctlvrefup 設置值有:[Auto] [0] - [255] Ctl1 clkvrefup 設置值有:[Auto] [0] - [255] Ctl1 ckecsvrefup 設置值有:[Auto] [0] - [255] Ctl2 cmdvrefdn 設置值有:[Auto] [0] - [255] Ctl2 ctlvrefdn 設置值有:[Auto] [0] - [255] Ctl2 clkvrefdn 設置值有:[Auto] [0] - [255] Tc Odt Control ODT_READ_DURATION 設置值有:[Auto] [0] - [15] ODT_READ_DELAY 設置值有:[Auto] [0] - [7] ODT_WRITE_DURATION 設置值有:
DQ RTT PARK 設置值有:[Auto] [0 DRAM Clock] [34 DRAM Clock] [40 DRAM Clock] [48 DRAM Clock] [60 DRAM Clock] [80 DRAM Clock] [120 DRAM Clock] [240 DRAM Clock] DQ RTT PARK DQS 設置值有:[Auto] [0 DRAM Clock] [34 DRAM Clock] [40 DRAM Clock] [48 DRAM Clock] [60 DRAM Clock] [80 DRAM Clock] [120 DRAM Clock] [240 DRAM Clock] GroupA CA ODT 設置值有:[Auto] [0 DRAM Clock] [40 DRAM Clock] [60 DRAM Clock] [80 DRAM Clock] [120 DRAM Clock] [240 xDRAM Clock] [480 DRAM Clock] GroupA CS ODT 設置值有:[Auto] [0 DRAM Clock] [40 DRAM Clock] [60
Memory Training Algorithms 本菜單的項目用來讓您開啟或關閉不同的內存訓練演算法。 Early Command Training 設置值有:[Auto] [Enabled] [Disabled] SenseAmp Offset Training 設置值有:[Auto] [Enabled] [Disabled] Early ReadMPR Timing Centering 2D 設置值有:[Auto] [Enabled] [Disabled] Read MPR Training 設置值有:[Auto] [Enabled] [Disabled] Receive Enable Training 設置值有:[Auto] [Enabled] [Disabled] Jedec Write Leveling 設置值有:[Auto] [Enabled] [Disabled] Early Write Timing Centering 2D 設置值有:[Auto] [Disabled] [Enabled] Early Read Timing Centering 2D 設置值有:[Auto] [Disabl
Command Voltage Centering 設置值有:[Auto] [Disabled] [Enabled] Early Command Voltage Centering 設置值有:[Auto] [Disabled] [Enabled] Write Voltage Centering 2D 設置值有:[Auto] [Disabled] [Enabled] Read Voltage Centering 2D 設置值有:[Auto] [Disabled] [Enabled] Late Command Training 設置值有:[Disabled] [Enabled] [Auto] Round Trip Latency 設置值有:[Auto] [Disabled] [Enabled] Turn Around Timing Training 設置值有:[Auto] [Disabled] [Enabled] CMD CTL CLK Slew Rate 設置值有:[Auto] [Disabled] [Enabled] CMD/CTL DS & E 2D 設置值有:[Auto] [Disabled] [Enab
EARLY DIMM DFE Training 設置值有:[Auto] [Disabled] [Enabled] Tx Dqs Dcc Training 設置值有:[Auto] [Disabled] [Enabled] DRAM DCA Training 設置值有:[Auto] [Disabled] [Enabled] Write Driver Strength Training 設置值有:[Auto] [Disabled] [Enabled] Rank Margin Tool 設置值有:[Auto] [Disabled] [Enabled] Memory Test 設置值有:[Auto] [Disabled] [Enabled] DIMM SPD Alias Test 設置值有:[Auto] [Disabled] [Enabled] Receive Enable Centering 1D 設置值有:[Auto] [Disabled] [Enabled] Retrain Margin Check 設置值有:[Auto] [Disabled] [Enabled] Write Drive Strength Up/
tWRWR_sg 設置值有:[Auto] [0] - [127] tWRWR_dg 設置值有:[Auto] [0] - [127] tWRRD_sg 設置值有:[Auto] [0] - [511] tWRRD_dg 設置值有:[Auto] [0] - [511] tRDRD_dr 設置值有:[Auto] [0] - [255] tRDRD_dd 設置值有:[Auto] [0] - [255] tRDWR_dr 設置值有:[Auto] [0] - [255] tRDWR_dd 設置值有:[Auto] [0] - [255] tWRWR_dr 設置值有:[Auto] [0] - [127] tWRWR_dd 設置值有:[Auto] [0] - [255] tWRRD_dr 設置值有:[Auto] [0] - [127] tWRRD_dd 設置值有:[Auto] [0] - [127] tRPRE 設置值有:[Auto] [0] - [4] tWPRE 設置值有:[Auto] [0] - [4] tWRPRE 設置值有:[Auto] [0] - [1023] tPRPDEN 設置值有:[Auto] [0] - [3
tREFIX9 設置值有:[Auto] [0] - [255] Ref Interval 設置值有:[Auto] [0] - [8191] tXPDLL 設置值有:[Auto] [0] - [127] tXP 設置值有:[Auto] [0] - [127] tPPD 設置值有:[Auto] [0] - [15] tCCD_L_tDLLK 設置值有:[Auto] [0] - [15] Misc.
Controller 0, Channel 1 Control 本項目用來開啟或關閉 Controller 0 與 Channel 1。 設置值有:[Enabled] [Disabled] Controller 1, Channel 0 Control 本項目用來開啟或關閉 Controller 1 與 Channel 0。 設置值有:[Enabled] [Disabled] Controller 1, Channel 1 Control 本項目用來開啟或關閉 Controller 1 與 Channel 1。 設置值有:[Enabled] [Disabled] MC_Vref0-2 設置值有:[Auto] [0] - [65533] Fine Granularity Refresh mode 設置值有:[Auto] [Disabled] [Enabled] DRAM SPD Configuration SDRAM Density Per Die 設置值有:[Auto] [4 Gb] [8 Gb] [12 Gb] [16 Gb] [24 Gb] [32 Gb] [48 Gb] [64 Gb] SDRAM Ba
以下項目只有在 SA GV 設為 [Enabled]、[Fixed to 1st Point]、[Fixed to 2nd Point]、[Fixed to 3rd Point] 或 [Fixed to 4th Point] 時才會出現。 First Point Frequency 本項目可以指定頻率。0-MRC 自動,或是指定為整數的特定頻 率:2000Mhz。 設置值有:[0] - [65535] First Point Gear 本項目可以設置 SAGV 點的齒輪比。0-Auto、1-G1、2-G2 與 4-G4。設置值有:[0] - [4] Second Point Frequency 本項目可以指定頻率。0-MRC 自動,或是指定為整數的特定頻 率:2000Mhz。設置值有:[0] - [65535] Second Point Gear 本項目可以設置 SAGV 點的齒輪比。0-Auto、1-G1、2-G2 與 4-G4。設置值有:[0] - [4] Third Point Frequency 本項目可以指定頻率。0-MRC 自動,或是指定為整數的特定頻 率:2000Mhz。設置值有:[0] -
CPU Current Capability 本項目用來設置較高的數值提供更大的總電力範圍,同時擴展超頻頻率的範 圍。當系統超頻,或是 CPU 在較高負載需要獲得額外的電力支持時,請選擇 較高的數值。 設置值有:[Auto] [100%] - [140%] 當 CPU 超頻或是需負載額外的電力時,請設置較高的數值。 CPU VRM Switching Frequency 本項目用來設置 VRM 開關頻率。VRM 開關頻率影響瞬態回應與 VRM 元件 溫度。選擇 [Manual] 設置較高的頻率可以獲得較快的暫態響應速度。當處理 器運作於高電壓與高負載線校準值時,建議使用 VRM 散熱器主動冷卻。 設置值有:[Auto] [Manual] 請勿將散熱系統移除,散熱環境需受到監控。 以下項目只有在 CPU VRM Switching Frequency 設置為 [Manual] 時才會出現。 Fixed CPU VRM Switching Frequency(KHz) 本項目可讓您設置固定的 VRM 頻率。數值以 50kHz 為間隔,更改的範圍由 250kHz 至 500kHz。 CPU Power Dut
CPU VRM Thermal Control 關閉本項目可提高 CPU VRM 的溫度限制。 設置值有:[Auto] [Enabled] [Disabled] 請勿將散熱系統移除。 以下項目只有使用內置顯卡時才會出現。 CPU Graphics Load-line Calibration Load-line 是根據 Intel 所訂立之 VRM 規格,其設置值將影響繪圖處理器電 壓。CPU 顯卡運作電壓將依 CPU 顯卡的負載呈比例性遞減。繪圖處理器運行 電壓將依繪圖處理器的負載呈比例性遞減。從 Level 1 至 Level 8 中選擇,以 將處理器圖形電源電壓從 100% 調整至 0%。 設置值有:[Auto] [Level 1] [Level 2] [Level 3] [Level 4:Recommended for OC] [Level 5] [Level 6] [Level 7] 實際提升的性能將視 CPU 顯卡規格而異。請勿將散熱系統卸除。 CPU Graphics Current Capability 本項目用來設置繪圖處理器的電力相式控制功能。較高的值可提供更寬的總功 率範圍,並同時擴
Internal CPU Power Management 本項目用來管理與設置 CPU 電力。 Maximum CPU Core Temperature 設置 CPU 核心的最高允許溫度。當達到此溫度時,CPU 將會節流或關閉以防 止核心損壞。 設置值有:[Auto] [62] - [115] 請勿將數值設置太高,否則高溫可能會造成 CPU 永久損壞。 Turbo Mode Parameters IVR Transmitter VDDQ ICCMAX 設置值有:[Auto] [0] - [15] Unlimited ICCMAX 本項目用來開啟或關閉無限制 ICCMAX。支持 VR 電流限制(ICCMAX)值設 置至 511.75A 以上。[Auto] [Disabled] [Enabled]] CPU Core/Cache Current Limit Max. 本項目可讓您設置更高的電流限制以防止超頻時的頻率或功率節流。可以設置 為最大值(511.75)以防止超頻時節流。 設置值有:[Auto] [0.00] - [511.
Dual Tau Boost 本項目可讓您開啟 Dual Tau Boost 功能。僅適用於桌機 35W/65W/12W sku。啟用 DPTF 後,此功能將被忽略。 設置值有:[Disabled] [Enabled] IA AC Load Line 本項目用來設置 AC 負載線,以毫歐姆為單位。請使用 <+> 與 <-> 鍵調整數 值。 設置值有:[Auto] [0.01] - [62.49] IA DC Load Line 本項目用來設置 DC 負載線,以毫歐姆為單位。請使用 <+> 與 <-> 鍵調整數 值。 設置值有:[Auto] [0.01] - [62.
Enhanced TVB 本項目僅支持特定規格。 設置值有:[Auto] [Disabled] [Enabled] Overclocking TVB 開啟本項目可繪製溫度/頻率依賴性。 設置值有:[Auto] [Disabled] [Enabled] [+1Boost Profile] [+2Boost Profile] +1Boost Profile(K CPU): 此設置將在自動最佳化溫度控制的幫助下,增加一個 bin 的功率。 +2Boost Profile(K CPU): 此設置將在自動最佳化溫度控制的幫助下,增加兩個 bin 的功率。 以下的項目只有在 Overclocking TVB 設為 [Enabled] 時才會出現。 1-Core Active / 2-Core Active / 3-Core Active / 4-Core Active / 5-Core Active / 6-Core Active 設置值有:[Auto] [Enabled] 以下的項目只有在 1-Core Active、 2-Core Active、 3-Core Active、 4-Core Active、 5-C
以下項目只有在 Negative Ratio Offset B 設為 [User Specify] 時才會出現。 Ratio Offset 請使用 <+> 與 <-> 鍵調整數值。 設置值有:[0] - [31] V/F Point Offset Offset Mode Sign 1-11 設置值有:[+] [-] V/F Point 1-11 Offset 設置值有:[Auto] [0.001] - [0.
UnderVolt Protection 啟用本項目時,在操作系統運行期用戶將無法指定低電壓。建議維持啟用的默 認值。 [Disabled] 無低電壓保護。 [Enabled] 允許 BIOS 設置低電壓,但運行期啟用低電壓保護。 Core PLL Voltage 本項目可以用來設置 Core PLL VCC Trim。數值以 0.015V 為間隔,變更的範 圍由 0.900V 至 1.845V。 設置值有:[Auto] [0.90000] - [1.84500] GT PLL Voltage 本項目可以用來設置 GT PLL VCC Trim。數值以 0.015V 為間隔,變更的範 圍由 0.900V 至 1.845V。 設置值有:[Auto] [0.90000] - [1.84500] Ring PLL Voltage 本項目可以用來設置 Ring PLL VCC Trim。數值以 0.015V 為間隔,變更的範 圍由 0.900V 至 1.845V。 設置值有:[Auto] [0.90000] - [1.
PCH Core Voltage 本項目可以用來設置 PCH Core 電壓。數值以 0.010V 為間隔,變更的範圍由 0.700V 至 1.000V。 設置值有:[Auto] [0.70000] - [1.00000] Ring Down Bin 本項目用來開啟或關閉 Ring DownBin 功能。默認值為 [Enabled]。使用 OC mailbox 指令 0x19。 [Auto] 設為默認值。 [Disabled] 處理器不會降低環比率且會遵守需求的環比限制。 [Enabled] 處理器將降低環比率且可能無觀察到最大環比需求。 請留意關閉此功能可能會導致處理器過壓。 Min. CPU Cache Ratio 本項目用來設置處理器的非核心比值至可能的最小值。請使用 <+> 與 <-> 鍵調整數 值。 設置值有:[Auto] [8] - [85] Max. CPU Cache Ratio 本項目用來設置處理器的非核心比值至可能的最大值。請使用 <+> 與 <-> 鍵調整數 值。 設置值有:[Auto] [8] - [85] Max.
以下項目只有在 Actual VRM Core Voltage 設為 [Manual Mode] 時才會出現。 CPU Core Voltage Override 本項目用來讓您通過外部電壓調節器為處理器輸入電壓。請使用 <+> 與 <-> 鍵調整 數值。數值以 0.005V 為間隔,變更的範圍由 0.600V 至 1.700V。 設置值有:[Auto] [0.60000] - [1.70000] 以下項目只有在 Actual VRM Core Voltage 設為 [Offset Mode] 時才會出現。 Offset Mode Sign [+] 設置正數值偏移電壓。 [-] 設置負數值偏移電壓。 CPU Core Voltage Offset 本項目用來通過外部電壓調節器為處理器輸入電壓。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.005V 為間隔,變更的範圍由 0.005V 至 0.635V。 設置值有:[Auto] [0.00500] - [0.
Offset Voltage 本項目用來設置處理器核心電壓偏移值。請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為間隔,變更的範圍由 0.001V 至 0.999V。 設置值有:[Auto] [0.00100] - [0.99900] 請保存並重啟系統使更改生效。 Cache SVID Voltage 本項目可以設置環域要求的快取電壓。結果可能會受 Actual VRM Core Voltage 影 響。 設置值有:[Auto] [Manual Mode] [Adaptive Mode] 以下項目只有在 Cache SVID Voltage 設為 [Manual Mode] 時才會出現。 CPU Core Voltage Override 本項目可以用來設置快取電壓。請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為 間隔,變更的範圍由 0.600V 至 1.700V。 設置值有:[Auto] [0.60000] - [1.
以下項目只有在 CPU Graphics Voltage Mode 設置為 [Manual Mode] 時才會出 現。 CPU Graphics Voltage Override 本項目用來設置 CPU 顯卡電壓。請使用 <+> 與 <-> 鍵調整數值。數值以 0.005V 為間隔,變更的範圍由 0.600V 至 1.700V。 設置值有:[Auto] [0.60000] - [1.70000] 以下項目只有在 CPU Graphics Voltage 設為 [Offset Mode] 時才會出現。 Offset Mode Sign [+] 設置正數值偏移電壓。 [-] 設置負數值偏移電壓。 CPU Graphics Voltage Offset 本項目用來設置處理器顯卡電壓偏移值。請使用 <+> 與 <-> 鍵調整數值。數值以 0.005V 為間隔,變更的範圍由 0.005V 至 0.635V。 設置值有:[Auto] [0.00500] - [0.
Offset Voltage 本項目用來設置 CPU L2 電壓偏移值。請使用 <+> 與 <-> 鍵調整數值。數值以 0.001V 為間隔,變更的範圍由 0.001V 至 0.999V。 設置值有:[Auto] [0.00100] - [0.99900] 請保存並重啟系統使更改生效。 CPU System Agent Voltage 本項目可以用來設置 CPU System Agent 電壓。 設置值有:[Auto] [Manual Mode] [Offset Mode] 以下項目只有在 CPU System Agent Voltage 設為 [Manual Mode] 時才會出現。 CPU System Agent Voltage Override 本項目用來通過外部電壓調節器為處理器輸入電壓。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.001V 為間隔,變更的範圍由 0.700V 至 1.800V。 設置值有:[Auto] [0.70000] - [1.
DRAM VDDQ Voltage 本項目用來設置 DRAM IC 的 VDD 數據部分電源。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.005V 為間隔,變更的範圍由 0.800V 至 1.435V。 設置值有:[Auto] [0.80000] - [1.43500] Advanced Memory Voltages IVR Transmitter VDDQ Voltage 本項目可以為內存控制器設置內部發射器的電壓。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.005V 為間隔,變更的範圍由 0.700V 至 2.200V。 設置值有:[Auto] [0.70000] - [2.20000] Memory Controller Voltage 本項目可以用來設置內存控制器電壓。請使用 <+> 與 <-> 鍵調整數值。數值以 0.010V 為間隔,變更的範圍由 1.006V 至 2.006V。 設置值有:[Auto] [1.00600] - [2.
DRAM VPP Voltage 本項目可以設置 DRAM 啟動電源供應器的電源。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.005V 為間隔,變更的範圍由 1.500V 至 2.135V。 設置值有:[Auto] [1.50000] - [2.13500] DRAM VDD Switching Frequency 本項目可以 Mhz 為單位設置 DRAM VDD 調節器的切換頻率。請使用 <+> 與 <-> 鍵調整數值。數值以 0.250MHz 為間隔,更改的範圍由 0.750MHz 至 1.500MHz。 設置值有:[Auto] [0.75000] - [1.50000] DRAM VDDQ Switching Frequency 本項目可以 Mhz 為單位設置 DRAM VDDQ 調節器的切換頻率。請使用 <+> 與 <-> 鍵調整數值。數值以 0.250MHz 為間隔,更改的範圍由 0.750MHz 至 1.500MHz。 設置值有:[Auto] [0.75000] - [1.
PMIC0-3 DRAM VPP Voltage 本項目可以設置 DRAM 啟動電源供應器的電源。請使用 <+> 與 <-> 鍵調整數 值。數值以 0.005V 為間隔,變更的範圍由 1.500V 至 2.135V。 設置值有:[Auto] [1.50000] - [2.13500] PMIC0-3 DRAM VDD Switching Frequency 本項目可以 Mhz 為單位設置 DRAM VDD 調節器的切換頻率。請使用 <+> 與 <-> 鍵調整數值。數值以 0.250MHz 為間隔,更改的範圍由 0.750MHz 至 1.500MHz。 設置值有:[Auto] [0.75000] - [1.50000] PMIC0-3 DRAM VDDQ Switching Frequency 本項目可以 Mhz 為單位設置 DRAM VDDQ 調節器的切換頻率。請使用 <+> 與 <-> 鍵調整數值。數值以 0.250MHz 為間隔,更改的範圍由 0.750MHz 至 1.500MHz。 設置值有:[Auto] [0.75000] - [1.
6.
6.
SA - PCI Express DMI ASPM 本項目用來設置 DMI ASPM 支持。 設置值有:[Disabled] [Auto] [ASPM L0s] [ASPM L1] [ASPM L0sL1] DMI Gen3 ASPM 本項目用來設置 DMI Gen3 ASPM 支持。 設置值有:[Disabled] [Auto] [ASPM L0s] [ASPM L1] [ASPM L0sL1] PEG - ASPM 本項目用來控制 PEG 0 的 ASPM 支持。若 PEG 不是目前使用的設備則無效。 設置值有:[Disabled] [L0s] [L1] [L0sL1] PCI Express Clock Gating 本項目用來開啟或關閉每個連接端口的 PCI Express Clock Gating。 設置值有:[Disabled] [Enabled] 6.
Hardware Prefetcher 啟用或關閉 MLC 控制器。 設置值有:[Disabled] [Enabled] Adjacent Cache Line Prefetch 本項目可以讓處理器在 L2 Cache 進行預取反饋和數據,從而降低內存負荷時間, 改善系統性能。 設置值有:[Disabled] [Enabled] Intel (VMX) Virtualization Technology 當本項目設為 [Enabled] 時,啟動 Intel 虛擬技術(Virtualization Technology),讓 硬件平台可以同時運行多個操作系統。 設置值有:[Disabled] [Enabled] Per P-Core Control 設置值有:[Disabled] [Enabled] 以下項目只有在 Per P-Core Control 設為 [Enabled] 時才會出現。 P-Core 0-5 請勿同時關閉所有 P-core 選項,否則 P-core 選項會在重新啟動後重置。 設置值有:[Enabled] [Disabled] Per E-Core Control 設置值有:[D
Per Core Hyper-Threading 本菜單的項目用來開啟或關閉每個核心的超線程。。 Hyper-Threading of Core 0-5 設置值有:[Disabled] [Enabled] Total Memory Encryption 本項目用來設置全內存加密(TME)以保護動態隨機存取內存數據免受物理攻擊。 設置值有:[Disabled] [Enabled] Legacy Game Compatibility Mode 本項目設為 [Enabled] 時,按下捲軸鎖定鍵可切換為效率核心, 同時捲軸鎖定指示燈 會亮起。 設置值有:[Disabled] [Enabled] CPU - Power Management Control 本項目用來管理與設置處理器電力。 Boot performance mode 在操作系統切換前允許您選擇 BIOS 的性能狀態。 設置值有:[Max Battery] [Max Non-Turbo Performance] [Turbo Performance] [Auto] Intel(R) SpeedStep(tm) 本項目可以支持兩個以上的頻率。 設置
以下項目只有在 Acoustic Noise Mitigation 設為 [Enabled] 時才會出現。 Pre Wake Time 本項目讓您以 micro ticks 為單位設置最大 Pre Wake 隨機分派時 間。這是為了減輕噪音動態週期性改變(DPA)調整。請使用 <+> 與 <-> 鍵調整數值。 設置值有:[0] - [255] Ramp Up Time 本項目讓您以 micro ticks 為單位設置最大 Ramp Up 隨機分派時 間。這是為了減輕噪音動態週期性改變(DPA)調整。請使用 <+> 與 <-> 鍵調整數值。 設置值有:[0] - [255] Ramp Down Time 本項目讓您以 micro ticks 為單位設置最大 Ramp Up 隨機分派時 間。這是為了減輕噪音動態週期性改變(DPA)調整。請使用 <+> 與 <-> 鍵調整數值。 設置值有:[0] - [255] IA VR Domain Disable Fast PKG C State Ramp for IA Domain 需要配置此選項以在更深的 C-state 期間減少噪音。 [FALSE] 請勿在更深的 C
Package C State Limit 本項目可讓您設置處理器封包的 C-state 限制。設置為 [CPU Default] 會將其 保留為出廠默認值。設置為 [Auto] 將初始化最深的可用封包 C-State 限制。 設置值有:[C0/C1] [C2] [C3] [C6] [C7] [C7s] [C8] [C9] [C10] [CPU Default] [Auto] Thermal Monitor 本項目可讓您啟用或停用 Thermal Monitor。 設置值有:[Disabled] [Enabled] Dual Tau Boost 本項目可讓您開啟 Dual Tau Boost 功能。僅適用於桌機 35W/65W/125W sku。啟用 DPTF 後,此功能將被忽略。 設置值有:[Disabled] [Enabled] 6.
Memory Configuration 本項目用來設置內存配置參數。 Memory Remap 本項目用來開啟或關閉 4GB 以上的內存 remap。 設置值有:[Enabled] [Disabled] Graphics Configuration 本項目用來選擇以處理器、PEG 顯示設備或 PCIe 顯示設備作為優先使用的顯示設 備。 Primary Display 本項目用來選擇以處理器、PEG 顯示設備或 PCIe 顯示設備作為優先使用的顯 示設備。 設置值有:[Auto] [CPU Graphics] [PEG Slot] [PCIE] iGPU Multi-Monitor 將此項目設置為 [Enabled] 以啟用整合與獨立顯卡的多顯示器輸出。iGPU 共享 系統內存大小將固定為 64M。 設置值有:[Disabled] [Enabled] DVMT Pre-Allocated 本項目可以讓您選擇內部顯示設備使用的 DVMT 5.
Map SATA Controller under VMD 本項目用來 map 或 unmap 本啟動連接端口至 VMD。 設置值有:[Disabled] [Enabled] 如果將 Map SATA Controller under VMD 設為 [Enabled] 時,請確認將 Map PCIE Storage under VMD 設為 [Disabled]。 PCI Express Configuration 本子菜單中的項目可以讓您為不同的內置插槽配定 PCIe 速度。 子菜單的項目會因主板而異。關於實際設置與選項,請參考主板的 BIOS。 6.
6.5 PCH 儲存設備設置(PCH Storage Configuration) 當您進入 BIOS 設置程序時,BIOS 設置程序將自動檢測已安裝的 SATA 設備。當未 檢側到 SATA 設備時將顯示 Empty 。將滾動條往下滾動來顯示其他 BIOS 項目。 本菜單中的項目可能因您的主板而異。關於實際設置與選項,請參考主板的 BIOS。 SATA Controller(s) 啟用或關閉 SATA 控制器。 設置值有:[Disabled] [Enabled] 以下項目只有在 SATA Controller(s) 設為 [Enabled] 時才會出現。 Aggressive LPM support 當本項目設置為 [Enabled] 時,可以讓 PCH 主動進入連接電源狀態。 設置值有:[Disabled] [Enabled] SMART Self Test S.M.A.R.T.
SATA6G 本項目可啟用或關閉選擇的 SATA 連接端口。 設置值有:[Disabled] [Enabled] SATA6G Hot Plug 指定此連接端口支持熱插拔功能。 設置值有:[Disabled] [Enabled] 6.
6.
DTBT Controller 0 Configuration DTBT Contorller 0 設置值有:[Disabled] [Enabled] TBT Host Router 可以依據可用連接端口啟用主機路由器。 設置值有:[One Port] [Two Port] Extra Bus Reserved 本項目用來選擇 TBT Root Port Type。 [56] One port Host。 [106] Two port Host.
6.
Endorsement Hierarchy 本項目用來啟動或關閉 Endorsement Hierarchy。 設置值有:[Disabled] [Enabled] Physical Presence Spec Version 本項目用來選擇告訴操作系統支持 PPI 版本 1.2 或 1.3。 設置值有:[1.2] [1.3] 部分 HCK 測試可能未支持 PPI Spec 版本 1.3。 TPM 2.0 UEFI Spec Version 本項目可以選擇 TCG2 規格版本支持。 [TCG_1_2] 兼容於 Windows 8 / Windows 10 模式。 [TCG_2] 支持新 TCG2 協定與事件格式,適用於 Windows 10 或更高版本。 6.
SR-IOV Support 若系統支持 SR-IOV 的 PCIe 設備,本項目用來開啟或關閉 Single Root IO Virtualization Support 功能。 設置值有:[Disabled] [Enabled] 6.
USB Single Port Control 本項目用來啟動或關閉個別 USB 連接端口。 USB 接口的位置請參考主板用戶手冊裡 主板構造圖 與 後側面板接口 的說明。 6.11 網絡協定堆棧設置(Network Stack Configuration) 本菜單可讓您更改網絡協定堆棧的各項相關設置。 Network stack 本項目用來啟動或關閉 UEFI 網絡協定堆棧(Network Stack)功能。 設置值有:[Disabled] [Enabled] 以下的項目只有在 Network Stack 設為 [Enabled] 時才會出現。 Ipv4/Ipv6 PXE Support 本項目用來啟動或關閉 Ipv4/Ipv6 PXE 啟動選項。 設置值有:[Disabled] [Enabled] 6.
6.13 HDD/SSD SMART 信息(HDD/SSD SMART Information) 本菜單顯示已連結設備的 SMART 信息。 本菜單的顯示選項會依連接至主板的設備而異。關於實際設置與選項,請參考主 板的 BIOS。 NVM Express 設備不支持 SMART 信息。 6.
ErP Ready 在 S4+S5 或 S5 休眠模式下關閉某些電源,減少待機模式下電力的流失,以符合歐 盟能源使用產品(Energy Related Product)的規範。當設置為 [Enabled] 時,其他 PME 選項將被關閉。RGB LED 指示燈與 RGB/可尋址燈條接針也會被關閉。 設置值有:[Disabled] [Enabled (S4+S5)] [Enabled (S5)] Power On By PCI-E 本項目用來啟動或關閉內置網絡控制器或其他安裝的 PCI-E 網卡的喚醒功能。 設置值有:[Disabled] [Enabled] Power On By RTC 本項目用來關閉或開啟實時時鐘(RTC)喚醒功能,啟用時,您可自行設置天、小 時、分、秒以安排時間讓系統自動啟動。 設置值有:[Disabled] [Enabled] 6.
HD Audio 本項目用來讓您使用高保真音頻控制器。 [Disabled] 高保真音頻無條件關閉。 [Enabled] 高保真音頻無條件開啟。 Intel LAN 本項目用來開啟或關閉 Intel LAN。 設置值有:[Disabled] [Enabled] USB power delivery in Soft Off state (S5) 本項目用來當您的電腦處於 S5 狀態時開啟或關閉 USB 電源。 設置值有:[Disabled] [Enabled] Connectivity mode (Wi-Fi & Bluetooth) 本項目用來開啟或關閉 Wi-Fi 與藍牙連接模堆。 設置值有:[Disabled] [Enabled] LED lighting 系統在工作狀態時 當系統在工作狀態時,本項目用來關閉或開啟 RGB LED 指示燈。 [All On] 所有 RGB 指示燈與功能指示燈將開啟。 [Stealth Mode] 所有 RGB 指示燈與功能指示燈將關閉。 [Aura Only] RGB 指示燈將開啟,功能指示燈將關閉。 [Aura Off] 功能指示燈開啟,RGB
Serial Port 本項目可以啟動或關閉串口。 設置值有:[Enabled] [Disabled] 以下的項目只有在 Serial Port 設為 [Enabled] 時才會出現。 Change settings 本項目用來為 Super I/O 設備選擇最佳設置。 設置值有:[Disabled] [Enabled] Intel Arc Graphics 本項目可以最佳化 Intel Arc Graphics 性能。 設置值有:[Enabled] [Disabled] 6.
7.
Voltage and Current Monitor CPU Core Voltage, 12V Voltage, 5V Voltage, 3.3V Voltage, Memory Controller Voltage [x.
CPU Fan Speed Low Limit 本項目用來設置風扇/水泵的最低速度警告值。當達到這個最低速度時,會出 現警告信息。若設定為 [Ignore],將不會再出現警告信息。 設置值有:[Ignore] [200 RPM] [300 RPM] [400 RPM] [500 RPM] [600 RPM] 以下項目只有在 CPU Fan Profile 設為 [Manual] 時才會出現。 CPU Fan Point4 Temperature 當溫度源小於 P4 溫度,佔空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調整溫度。 CPU Fan Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調整風扇/水泵的占 空比。 CPU Fan Point3 Temperature 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P3-P4 占空
CPU Fan Point1 Duty Cycle (%) 當溫度源小於 P1 溫度,風扇會運作於 P1 占空比。當溫度源大於 P1 溫度, 占空比會依據 P1-P2 與溫度源決定。使用 <+> 或 <-> 鍵調整風扇/水泵的占 空比。 Chassis Fan(s) Configuration Chassis Fan Q-Fan Control 本項目用來設置 Chassis Fan 運作模式。 [Auto Detect] 檢測安裝的風扇/水泵類型並自動切換控制模式。 [DC Mode] 在 DC 模式啟動 Q-Fan Control 來使用 3-pin 風扇/水 泵。 [PWM Mode] 在 PWM 模式啟動 Q-Fan Control 來使用 4-pin 風 扇/水泵。 Chassis Fan Profile 本項目用來設置風扇/水泵適當的性能。選擇 [Manual] 時,當處理 器溫度超過 75°C 時,建議將風扇/水泵的占空比設為 100%。請 留意當風扇/水泵占空比不足導致過熱,會造成處理器性能限制。 設置值有:[Standard] [Silent] [Turbo] [Full Speed]
以下項目只有在 Chassis Fan 1-5 Profile 設為 [Manual] 時才會出現。 Chassis Fan Point4 Temperature 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫 度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵 調整溫度。 Chassis Fan Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫 度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵 調整風扇/水泵的占空比。 Chassis Fan Point3 Temperature 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫 度源大於 P3 溫度,風扇會運作於 P3-P4 占空比。使用 <+> 或 <-> 鍵調整溫度。 Chassis Fan Point3 Duty Cycle (%) 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫 度源大於 P3 溫度,風扇會運作於 P3-P4 占空比。使用 <+> 或 <-
AIO Pump Q-Fan Control 本項目用來設置 AIO Pump 運作模式。 [Auto Detect] 檢測安裝的風扇/水泵類型並自動切換控制模式。 [DC Mode] 在 DC 模式啟動 Q-Fan Control 來使用 3-pin 風扇/水泵。 [PWM Mode] 在 PWM 模式啟動 Q-Fan Control 來使用 4-pin 風扇/水泵。 AIO Pump Profile 本項目用來設置風扇/水泵適當的性能。選擇 [Manual] 時,當處理器溫度超過 75°C 時,建議將風扇/水泵的占空比設為 100%。請留意當風扇/水泵占空比 不足導致過熱,會造成處理器性能限制。 設置值有:[Standard] [Silent] [Turbo] [Full Speed] [Manual] 以下項目只有在 AIO Pump Profile 設為 [Standard]、[Silent]、[Turbo] 或 [Manual] 時才會出現。 AIO Pump Q-Fan Source 指派的風扇/水泵會依選擇的溫度來源運作。 設置值有:[CPU] [MotherBoard] [VRM] [C
以下項目只有在 AIO Pump Profile 設為 [Manual] 時才會出現。 AIO Pump Point4 Temperature 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調整溫度。 AIO Pump Point4 Duty Cycle (%) 當溫度源小於 P4 溫度,占空比會依據 P3-P4 與溫度源決定。當溫度源大於 P4 溫度,風扇會運作於 P4 占空比。使用 <+> 或 <-> 鍵調整風扇/水泵的占 空比。 AIO Pump Point3 Temperature 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫度源大於 P3 溫度,風扇會運作於 P3-P4 占空比。使用 <+> 或 <-> 鍵調整溫度。 AIO Pump Point3 Duty Cycle (%) 當溫度源小於 P3 溫度,占空比會依據 P2-P3 與溫度源決定。當溫度源大於 P3 溫度,風扇會運作於 P3-P4 占空比。使用 <+> 或 <-> 鍵調整風扇/水泵的 占空比。 AIO Pum
Chassis Intrusion Detection Support 當本項目設為 [Enabled] 時可啟用機箱檢測功能。 設置值有:[Enabled] [Disabled] CPU Temperature LED Switch 當本項目設置為 [Enabled] 時可啟用 CPU_LED 指示燈在處理器高溫時亮起。 設置值有:[Enabled] [Disabled] 78 PRIME / ProArt / TUF GAMING Intel 700 系列 BIOS 用戶手冊
8.
Boot from Storage Devices 本項用來選擇想要運行的存儲設備類型。 設置值有:[Ignore] [Legacy only] [UEFI only] Boot from PCI-E/PCI Expansion Devices 本項目用來選擇想要運行的 PCIe/PCI 擴展設備類型。 設置值有:[Ignore] [Legacy only] [UEFI only] Secure Boot 本項目用來設置 Windows® 安全啟動的相關參數以及管理系統金鑰,以提升系統在 啟動自檢(POST)時的安全性,避免受到未授權的用戶與惡意軟件的危害。 OS Type [Windows UEFI Mode] 本項目用來選擇安裝的操作系統。運行 Microsoft® 安全啟動檢查。只有在 Windows® UEFI 模式或其他 Microsoft® 安全啟動兼容操作 系統中啟動時選擇此項目。 [Other OS] 在 Windows® 非 UEFI 模式中啟動時獲得最 佳功能。Microsoft® 安全啟動功能僅支持 Windows® UEFI 模式。 Microsoft® 安全啟動功能只可在 W
Set New key 本項目用來由 USB 存儲設備載入已下載平台金鑰(PK)。 Delete key 本項目用來刪除系統中的 PK。當平台金鑰刪除後即無法使用安全 啟動金鑰。 設置值有:[Yes] [No] PK 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 KEK Management KEK(金鑰交換金鑰 [Key-exchange Key] 或金鑰註冊金鑰 [Key-Enrollment Key])用來管理簽名數據庫(db)與撤銷簽名數據庫(dbx)。 Key-exchange Key(KEK)指的是 Microsoft® Secure Boot Key-Enrollment Key(KEK)。 Save to file 本項目用來將平台金鑰(KEK)保存至 USB 存儲設備。 Set New key 本項目用來由 USB 存儲設備載入已下載平台金鑰(KEK)。 Append Key 本項目用來由存儲設備載入附加的 KEK,以管理附加的簽名數據庫 (db)與撤銷簽名數據庫(dbx)。 Delete key 本項目用來刪除系統中的 KEK。 設置值有:[Yes] [No] KEK
DBX Management dbx(撤銷簽名數據庫)列出 db 項目中不再被信任且無法被載入之被禁止的 圖片影像。 Save to file 本項目用來保存 dbx 至 USB 存儲設備。 Set New key 本項目用來由 USB 存儲設備載入已下載 dbx。 Append Key 本項目用來由存儲設備載入附加的 dbx,以管理附加的簽名數據庫 (db)與撤銷簽名數據庫(dbx)。 Delete key 本項目用來刪除系統中的 dbx。 設置值有:[Yes] [No] dbx 文件必須格式化為一個基於時間認證變量的 UEFI 變量結構。 Boot Configuration Fast Boot 本項目可以啟用或關閉啟動時僅運行最少所需設備。不會對 BBS 啟動選項造 成影響。 設置值有:[Disabled] [Enabled] 以下項目只有在 Fast Boot 設為 [Enabled] 時才會出現。 Next Boot after AC Power Loss [Normal Boot] 電源中斷後,在下一次啟動時恢復至正常啟動速度。 [Normal Boot] 電源中斷後,在下一次啟動時加快啟動速
以下項目只有在 Boot Logo Display 設為 [Disabled] 時才會出現。 Post Report 本項目可以選擇 POST 的等候時間或直到按下 ESC。 設置值有:[1 sec] - [10 sec] [Until Press ESC] Boot up NumLock State 本項目可以選擇鍵盤 NumLock 狀態。 設置值有:[On] [Off] Wait For ‘F1’ If Error 系統啟動過程出現錯誤信息時,本項目可讓系統等待您按下 鍵確認才會 繼續進行啟動程序。 設置值有:[Disabled] [Enabled] Option ROM Messages [Force BIOS] [Keep Current] 選購設備固件信息會在啟動自檢時顯示。 在啟動自檢時只顯示華碩啟動圖標。 Interrupt 19 Capture 本項目用來開啟或關閉選購設備固件信息以進行 Interrupt 19 Capture。 設置值有:[Enabled] [Disabled] AMI Native NVMe Driver Support 本項目用來開啟或關閉 AMI N
Boot Option Priorities 本項目讓您自行選擇啟動磁盤並排列啟動設備順序。依照 1st、2nd、3rd 順序分別 代表其啟動設備順序,而設備的名稱將因使用的硬件設備不同而有所差異。 • 欲進入 Windows® 安全模式時,請在啟動自檢(POST)時按下 (Windows® 8 不支持這項功能)。 • 啟動時您可以在 ASUS Logo 出現時按下 選擇啟動設備。 Boot Override 這些項目會顯示可用的設備。依照 1st、2nd、3rd 順序分別代表其啟動設備順序, 而設備的名稱將因使用的硬件設備不同而有所差異。點擊任一設備可將該將置設置 為啟動設備。 84 PRIME / ProArt / TUF GAMING Intel 700 系列 BIOS 用戶手冊
9.
9.1 華碩 EZ Flash 3 公用程序(ASUS EZ Flash 3 Utility) 本項目可以讓您運行華碩 EZ Flash 3 公用程序。按下 會出現再次確認的窗 口,請使用左右鍵選擇 [Yes] 或 [No],接著按下 確認。 請參考 華碩 EZ Flash 3 的說明。 9.
9.
9.4 華碩 SPD 信息(ASUS SPD Information) 本菜單顯示內存插槽的相關信息。 9.
9.6 華碩 Armoury Crate 本項目用來讓您在 Windows® 操作系統中開啟或關閉 Armoury Crate 應用程序的下 載與安裝。Armoury Crate 應用程序可以幫助您管理與下載主板最新的驅動程序與 公用程序。 Download & Install ARMOURY CRATE app 設置值有:[Disabled] [Enabled] 9.
10. 退出 BIOS 程序(Exit menu) 本菜單可讓您讀取 BIOS 程序出廠默認值與退出 BIOS 程序,並可保存與取消對 BIOS 項目的更改。你也可以由 Exit 菜單進入 EZ Mode。 Load Optimized Defaults 本項目可讓您載入 BIOS 程序設置菜單中每個參數的默認值。當您選擇本項目或按下 ,便會出現一個確認對話窗口,選擇 OK 以載入默認值。 Save Changes & Reset 當您完成對 BIOS 設置程序所做的更改後,請選擇本項目或按下 ,將會出現 一個確認對話窗口,請選擇 OK 以保存設置並退出 BIOS 設置程序。 Discard Changes & Exit 本項目可讓您放棄所做的更改,並恢復原先保存的設置。在選擇本項目或按下 鍵後,將會出現一個確認對話窗口,請選擇 Yes 以放棄任何設置並載入原先保存的 設置,同時退出 BIOS 設置程序。 Launch EFI Shell from USB drives 本項目可以讓您由含有數據系統的設備中啟動 EFI Shell(shellx64.
11. 升級 BIOS 程序 華碩網站上提供有最新的 BIOS 程序,可以強化系統的穩定度、兼容性或運行性能, 但是運行 BIOS 程序升級是具有潛在性風險的,若是使用現有版本的 BIOS 程序未發 生問題時,請勿手動運行升級 BIOS 程序。不適當的 BIOS 程序升級可能會導致系統 啟動失敗。若有需要,請使用以下各節的方法來升級您的 BIOS 程序。 請訪問華碩網站(http://www.asus.com/support)來下載本主板最新的 BIOS 文 件。 以下工具程序項目提供您管理與升級主板 BIOS 設置程序。 1. ASUS EZ Flash 3:使用 U 盤來升級 BIOS。 3. ASUS CrashFree BIOS 3: 當 BIOS 文件遺失或損毀時,可以使用 U 盤來升級 BIOS。 11.1 華碩 EZ Flash 3(ASUS EZ Flash 3) 華碩 EZ Flash 3 程式讓您使用 U 盤輕鬆的升級 BIOS 程序。 請依照以下步驟通過華碩 EZ Flash 3 升級 BIOS 程序: 1.
11.2. ASUS CrashFree BIOS 3 華碩最新自行研發的 CrashFree BIOS 3 工具程序,讓您在當 BIOS 程序和數據被病 毒入侵或毀損時,可以輕鬆的從含有最新或原始 BIOS 文件的 U 盤中恢復 BIOS 程 序的數據。 請至 http://www.asus.com/support 網站下載最新 BIOS 文件,並保存在 U 盤 中。 恢復 BIOS 程序 請依照下列步驟恢復 BIOS 程序: 1. 啟動系統。 2. 將含有最新或原始 BIOS 文件的 U 盤插入 USB 連接端口。 3. 接著工具程序便會自動檢查存儲設備中是否存有 BIOS 文件。當搜索到 BIOS 文件後,工具程序會開始讀取 BIOS 文件並自動進入 ASUS EZ Flash 3 程序。 4.