主機板針腳說明 T11133 第二版 2016 年 7 月
目錄 主機板針腳說明 1-2 1 連接排針......................................................................................................................... 1-3 2 跳線選擇區..................................................................................................................... 1-4 3 內部連接埠..................................................................................................................... 1-6 4 內建 LED 指示燈......................................................................................
1 連接排針 1. CMOS 組態資料清除(2-pin CLRTC) CLRTC +3V_BAT GND 在主機板上的 CMOS 記憶體中記載著正確的時間與系統硬體組態 等資料,這些資料並不會因電腦電源的關閉而遺失資料與時間的正 確性,因為這個 CMOS 的電源是由主機板上的鋰電池所供應。 PIN 1 想要清除這些資料,可以依照下列步驟進行: 1. 關閉電腦電源,拔掉電源線; 2. 用一個金屬物體,如螺絲起子,將 CLRTC 跳線的兩個針腳短路。 3. 插上電源線,開啟電腦電源; 4. 當開機步驟正在進行時按著鍵盤上的 <Del> 鍵進入 BIOS 程式畫面重新 設定 BIOS 資料。 • 如果上述方法無效,請將內建電池移除,並再次將此兩針短路以清除 CMOS RTC RAM 資料。CMOS 清除完畢後,重新安裝電池。 • 如果您是因為超頻的緣故導致系統無法正常開機,您無須使用上述的 組態資料清除方式來排除問題。建議可以採用 C.P.R(CPU 參數自動回 復)功能,只要將系統重新啟動 BIOS 即可自動回復預設值。 2.
2 跳線選擇區 1. CMOS 組態資料清除(3-pin CLRTC) 在主機板上的 CMOS 記憶體中記載著正確的時間與系統 硬體組態等資料,這些資料並不會因電腦電源的關閉而遺失 資料與時間的正確性,因為這個 CMOS 的電源是由主機板 上的鋰電池所供應。 1 CLRTC 2 2 3 Normal (Default) Clear RTC 想要清除這些資料,可以依照下列步驟進行: 1. 關閉電腦電源,拔掉電源線; 2. 將 CLRTC 跳線帽由 [1-2](預設值)改為 [2-3] 約五∼十秒鐘(此時即清 除 CMOS 資料),接著再將跳線帽改回 [1-2]; 3. 插上電源線,開啟電腦電源; 4.
3. USB 裝置喚醒跳線(3-pin USBPWF) 若將此跳線設為 +5V,可透過連接的 USB 裝置將電腦從 S1 睡眠模式(CPU 停止工作,DRAM 更新,系統以低功耗模式運 作)喚醒。若將此跳線設為 +5VSB,可將電腦從 S3 與 S4 睡 眠模式(CPU 斷電,DRAM 緩慢更新,電源以低功耗模式運 作)喚醒。此跳線適用於內部 USB 連接埠。 USBPWF 1 2 3 2 +5VSB +5V (Default) • 該 USB 裝置喚醒跳線需要一個可提供 500mA 電流,5VSB 電壓的電源 支援,傳輸到每一個 USB 插槽。否則,系統將無法運作。 •不管是在正常情況下還是處於睡眠狀態中,電腦所消耗的總電流不能 超過電源供應能力(+5VSB)。 4.
3 內部連接埠 1. 序列埠連接插座(10-1 pin COM) COM PIN 1 DCD TXD GND RTS RI RXD DTR DSR CTS 這組插座是用來連接序列埠(COM)。將序列埠模組的排線連 接到這個插座,接著將該模組安裝到機殼後側面板空的插槽中。 2. 中央處理器 / 機殼風扇電源插槽(4-pin CPU_FAN、4-pin CHA_FAN) +5V CHA FAN IN CHA FAN PWR GND C 3. USB 3.0 連接插槽(20-1 pin) USB3+5V IntA_P1_SSRXIntA_P1_SSRX+ GND IntA_P1_SSTXIntA_P1_SSTX+ GND IntA_P1_DIntA_P1_D+ GND USB3 PIN 1 USB3+5V IntA_P2_SSRXIntA_P2_SSRX+ GND IntA_P2_SSTXIntA_P2_SSTX+ GND IntA_P2_DIntA_P2_D+ 這個插槽用來連接 USB 3.0 模組,可在前面板或後側連接 埠擴充 USB 3.0 模組。當您安裝 USB 3.
5. Single USB 2.0 連接插槽(5-1 pin) USBE5 +5V DC Data(negative) Data(positive) Groud 這些 USB 擴充套件排線插槽支援 USB 2.0 規格,將 USB 模組 排線連接至任何一個插槽,然後將模組安裝到機殼後面板中開放的 插槽。這些 USB 插槽與 USB 2.0 規格相容,並支援傳輸速率最高 達 480 Mbps。 PIN 1 EATX12V +12V DC +12V DC +12V DC +12V DC PIN 1 GND GND GND GND PIN 1 ATX12V +12V DC +12V DC 這些電源插槽用來連接一個 ATX 電源。電 源所提供的連接插頭已經過特別設計,只能以 一個特定方向插入主機板上的電源插槽。找到 正確的插入方向後,只需穩穩地將之套進插槽 中即可。 GND GND 6.
前面板音效連接排針 (10-1 pin AAFP) AGND NC NC HD-audio-compliant pin definition MIC2 MICPWR Line out_R NC Line out_L PIN 1 PORT1 L PORT1 R PORT2 R SENSE_SEND PORT2 L PIN 1 推薦您將支援高傳真(high definition)音效的 前面板音效模組連接到這組排針,如此才能獲 得高傳真音效的功能。 NC AAFP SENSE2_RETUR 這組音效外接排針供您連接到前面板的音效排線,除 了讓您可以輕鬆地透過主機前面板來控制音效輸入/輸 出等功能,並且支援 AC’97 或 HD Audio 音效標準。 將前面板音效輸出/輸入模組的連接排線之一端連接到 這個插槽上。 AGND NC SENSE1_RETUR 8. Legacy AC’97 compliant definition 9.
12. LVDS 連接排針(40-pin LVDS) 這些連接排針用來連接支援低電壓差分訊號連接埠 的 LCD 顯示螢幕。 PIN 21 ODD_Lane3_P ODD_Lane3_N ODD_Lane2_P ODD_Lane2_N ODD_Lane1_P ODD_Lane1_N ODD_Lane0_P ODD_Lane0_N EVEN_Lane3_P EVEN_Lane3_N EVEN_Lane2_P EVEN_Lane2_N EVEN_Lane1_P EVEN_Lane1_N EVEN_Lane0_P EVEN_Lane0_N EDID_GND LCD_VCC LCD_VCC LCD_VCC PIN 1 N/C EDID_3.
16.
系統控制面板連接排針 (20-5 pin PANEL) • 硬碟動作指示燈連接排針 (2-pin +HDD_LED-) PIN 1 +HDD_LED- +5V_SPKO Ground Ground Speaker SPEAKER RESET PLED- 這組排針可連接到電腦主機面板上的系統 電源指示燈。在您啟動電腦並且使用電腦的情 況下,該指示燈會持續亮著;而當指示燈閃爍 時,即表示電腦正處於睡眠模式中。 PWR_SW PLED+ PLEDPWR Ground • 系統電源指示燈連接排針 (2-pin/3-1 pin +PWR_ LED-) PANEL +PWR_LED- HDD_LED+ HDD_LEDGround RESET NC PLED+ 這一組連接排針包括了數個連接到電腦主機前面板 的功能接針。 +PWR_LED- * Requires an ATX power supply 您可以連接此組 HDD_LED 接針到電腦主機面 板上的硬碟動作指示燈,如此一旦硬碟有存取動作時,指示燈隨即亮起。 • 機殼喇叭連接排針 (4-pin SPEAKER) 這組 4-pin 排針
系統控制面板連接排針 (20-3 pin PANEL) • 硬碟動作指示燈連接排針 (2-pin +HDD_LED-) +5V GND GND Speaker Intruder# SPEAKER +HDD_LED- RESET GND CHASSIS PIN 1 PLED- 這組排針可連接到電腦主機面板上的系統 電源指示燈。在您啟動電腦並且使用電腦的情 況下,該指示燈會持續亮著;而當指示燈閃爍 時,即表示電腦正處於睡眠模式中。 PWR_SW PLED+ PLEDPWR GND • 系統電源指示燈連接排針 (2-p i n/3-1 p i n +PWR_LED-) PANEL +PWR_LED- HDD_LED+ HDD_LEDGND Reset NC PLED+ 這一組連接排針包括了數個連接到電腦主機前面 板的功能接針。 +PWR_LED- * Requires an ATX power supply 您可以連接此組 HDD_LED 接針到電腦主機面板上的硬碟動作指示燈,如 此一旦硬碟有存取動作時,指示燈隨即亮起。 • 機殼喇叭連接排針 (4-pin SPEAKER) 這組
17. TPM 插座 (20-1 pin TPM) PWRDWN GND +3VSB NC LAD0 +3V LAD3 PCIRST# FRAME PCICLK TPM GND PIN 1 NC CLKRUN SERIRQ NC GND LAD1 LAD2 NC 這個插座支援可信任安全平台模組(T P M)系統,用來安 全地儲存金鑰、數位認證、密碼和資料。可信任安全平台模組 (TPM)系統也用來協助加強網路安全,保護數位身份,以及 確保平台的安全性。 PIN 1 GND C_PCICLK_TPM +3V +3V 這個插座支援可信任安全平台模組(T P M)系統,用來安 全地儲存金鑰、數位認證、密碼和資料。可信任安全平台模組 (T P M)系統也用來協助加強網路安全,保護數位身份,以及確 保平台的安全性。 +3VSB S_PCIRST#_TBD TPM 插座 (14-1 pin TPM) PWRDWN F_SERIRQ F_FRAME# F_LAD3 F_LAD2 F_LAD1 F_LAD0 TPM 18. M.2 socket 3 這個插槽用來安裝 M.
20. 顯示螢幕亮度連接排針(8-pin LCD_BLKT_PANEL) LCD_BLKT_PANEL PIN 1 BKLT_EN BKLT_PWM BKLT_PWR BKLT_PWR BKLT_GND/Brightness_GND BKLT_GND/Brightness_GND Brightness_up Brightness_Down 這些連接排針用來控制 LCD 螢幕的背光與亮度,可啟用 LCD 螢幕背光、提供背光控制訊號并為前面板的亮度按鈕提 供亮度控制訊號。 21. LCD 顯示螢幕開關連接排針(2-pin PANEL_SW) 這組 2-pin 排針用來連接能夠關閉 LCD 顯示螢幕背光的顯示 螢幕開關。 PANEL_SW GND MON_SW# PIN 1 22.
25. DMIC 連接排針(4-pin DMIC) 這些 DMIC 連接排針用來連接用於一體機機殼的數位麥克風模 組。 +3.3V DMIC_DATA GND DMIC_CLK DMIC PIN 1 26. 自訂連接排針(14-pin CUSTOM) 這些自訂連接排針用來連接可設定附加功能的自訂模 組。 CUSTOM PIN 1 Prog_LED +3.
4 內建 LED 指示燈 1. 電力指示燈 當主機板上內建的電力指示燈(SB_PWR)亮著時,表 示目前系統是處於正常運作、省電模式或者軟關機的狀 態中,並非完全斷電。這個警示燈可用來提醒您在安裝 或卸除任何的硬體裝置之前,都必須先卸除電源,等待 警示燈熄滅才可進行。 SB_PWR ON Standby Power OFF Powered Off 2. 硬碟指示燈 (HD_LED) 這個指示燈設計用來顯示硬碟運作的狀態。當指示燈閃爍時表示正在讀取硬碟 的資料或資料正在寫入硬碟中,若是指示燈一直沒有亮起,則表示本主機板沒有 連接硬碟或是硬碟沒有作用。 3. Q 指示燈 (BOOT_DEVICE_LED、VGA_LED、DRAM_LED、CPU_LED) Q 指示燈從主機板啟動後依序查看 CPU、記憶體、顯示卡與啟動裝置狀態。當 發現錯誤時,在該項目旁的指示燈則會亮燈直到問題解決。透過直覺的方式提供 這項友善的設計,能在短短幾秒內找到問題點。 4. KeyBot 指示燈 (KEYBOT_LED) 這個指示燈會在 KeyBot 按鈕按下後亮燈顯示。 5.
5 主機板上的內建開關 當您想要針對未安裝在機殼的裸板或是開放機殼的系統作效能調校時,主機板上內 建的開關按鈕與重置按鈕可以方便您迅速地開關機或是重置系統。這個專為超頻者及 專業玩家的設計,可以方便且不間斷地進行調校,並讓效能有效地提升。 1. 啟動開關 (START) 本主機板擁有啟動開關,讓您可以喚醒系統或啟動,並以亮燈顯示 系統已接上電源為啟動狀態,並提醒您在主機板移除或插入任何元件 之前要先關機。 2. 重置開關(RESET) 按下重置開關以重新啟動系統。 RESET 3.
4. CMOS 組態資料清除按鈕(CLR_CMOS) 只有在系統因超頻而當機時按下本按鈕來清除 B I O S 設定資 訊。 5. KeyBot 按鈕(KeyBot) 按下按鈕可以啟用 KeyBot 功能。 KEBOT KeyBot 功能只支援 USB 鍵盤。 6. Sonic SoundStage 按鈕(SOUNDSTAGE) 按下按鈕可以啟用 Sonic SoundStage 功能。 SOUNDSTAGE 當按下 Sonic SoundStage 後,Q-Code 指示燈上會顯示 目前 Sonic SoundStage 檔案的設定檔。 7.