User Manual
Table Of Contents
- 1. UEFIとは
- 2. BIOS Setup Utility
- 3. BIOSの管理と更新
- 4. メニュー画面
- 5. Main
- 6. Ai Tweaker
- 7. Advanced
- 7.1 Platform Misc Configuration
- 7.2 CPU Configuration
- 7.3 System Agent (SA) Configuration
- 7.4 PCH Configuration
- 7.5 PCH Storage Configuration
- 7.6 PCH-FW Configuration
- 7.7 AMT Configuration
- 7.8 Thunderbolt(TM) Configuration
- 7.9 Trusted Computing
- 7.10 Redfish Host Interface Settings
- 7.11 Serial Port Console Redirection
- 7.12 Intel TXT Information
- 7.13 PCI Subsystem Settings
- 7.14 USB Configuration
- 7.15 Network Stack Configuration
- 7.16 NVMe Configuration
- 7.17 HDD/SSD SMART Information
- 7.18 APM Configuration
- 7.19 Onboard Devices Configuration
- 7.20 Intel(R) Rapid Storage Technology
- 8. Monitor
- 9. Boot
- 10. Tool
- 11. IPMI
- 12 Exit
32
Pro WS W680-ACE Series BIOSガイド
GT CEP Enable
GT CEP (Current Excursion Protection) サポートの有効/無効を設定します。Pcode
Mailbox Command 0x37、Sub-command 0x1 を使用し、Databit3を1に設定します。
設定オプション: [Auto] [Disabled] [Enabled]
SA CEP Enable
SA CEP (Current Excursion Protection) サポートの有効/無効を設定することができま
す。Pcode Mailbox Command 0x37、Sub-command 0x1 を使用し、Databit3を1に設定
します。
設定オプション: [Auto] [Disabled] [Enabled]
IA SoC Iccmax Reactive Protector
設定オプション: [Auto] [Disabled] [Enabled]
Inverse Temperature Dependency Throttle
設定オプション: [Auto] [Disabled] [Enabled]
IA VR Voltage Limit
Voltage Limit (VMAX)。この値は任意の時点で許容される最大瞬時電圧を表します。
BIOS VR mailbox command 0x8 を使用します。
設定オプション: [Auto] [0] - [7999]
CPU DLVR Bypass Mode Enable
設定オプション: [Auto] [Disabled] [Enabled]
CPU SVID Support
CPUと外部電圧レギュレーターとの通信の有効/無効を設 定します。
設定オプション: [Auto] [Disabled] [Enabled]
Tweaker’s Paradise
Realtime Memory Timing
リアルタイムでメモリータイミングを変 更することができる機能の有効/無効を設定しま
す。[Enabled] に設定すると、システムは MRC_DONE 後にリアルタイムのメモリータイミ
ング 変 更を実 行 できます。
設定オプション: [Disabled] [Enabled]
SPD Write Disable
SPD書込み禁止機能の有効/無効を設定します。セキュリティの推奨事項として、SPD書込
み 禁 止を 設 定 する 必 要 が あります。
設定オプション: [TRUE] [FALSE]
PVD Ratio Threshold
コアドメインP L Lの 場 合、より低 いポストディバイダに切り替えるしきい 値 は 既 定値 で
15です。BCLKを高くする場合は 15 より低い値を設定することで、Digitally Controlled
Oscilator (DCO) が適切な周波数で動作するようにすることができます。
設定オプション: [Auto] [1] - [40]
SA PLL Frequency Override
SA PLL の周波数を設定します。
設定オプション: [Auto] [3200 MHz] [1600 MHz]
BCLK TSC HW Fixup
PMAからAPICへのTSCコピー中にBCLK TSC HW Fixup disableを有効/無効にします。
設定オプション: [Enabled] [Disabled]