Motherboard RAID 設定 使用手冊 (INTEL)
T22370 第五版 2023 年 8 月 版權說明 © ASUSTeK Computer Inc. All rights reserved.
目錄 關於這本使用手冊 ................................................................................................................iv Intel® RAID 設定 1. RAID 定義 ....................................................................................................................... 1-5 2. 安裝儲存裝置 ................................................................................................................. 1-5 3. 於 UEFI BIOS 中建立 SATA RAID 設定 ..........................................................................
關於這本使用手冊 產品使用手冊包含了所有當您在建立 Intel® RAID 設定時所需用到的資訊。您可以依據不同的主 機板晶片或軟體以建立不同的 RAID 設定。 本使用手冊中的圖片僅供參考。圖片可能會依照您所購買的型號而有不同,但是設定步驟 相似。 哪裡可以找到更多的產品資訊 您可以到(www.asus.
Intel® RAID 設定 Intel® RAID 設定 若您的主機板支援 Intel® Rapid Storage Technology,您可以建立 RAID 0、RAID 1、RAID 5 與 RAID 10。 如果要將 Windows® 作業系統安裝到已組建 RAID 陣列的硬碟,必須在作業系統安裝期間建 立 RAID 驅動程式光碟片並載入 RAID 驅動程式。詳情請參考「8. 於 Windows® 10 作業系統與 Windows® 11 作業系統安裝時安裝 RAID 控制器驅動程式」。 1.
3. 於 UEFI BIOS 中建立 SATA RAID 設定 您可以使用 SATA 模式 M.2 模組與 SATA SSD/HDD 以建立 RAID 設定。 1. 在啟動自我檢測程序(Power-On Self Test,POST)時,進入 BIOS 設定程式。 關於如何在 BIOS 中針對選單進行瀏覽與輸入,請參考主機板 BIOS 手冊中的相關說明。 2. 選擇 Advanced(進階)選單 > System Agent(SA)設定 > VMD 設定選單。 3. 進入 VMD 設定選單後,將 Enable VMD controller 與 Map SATA Controller under VMD 項目設定為 [Enabled];將 Map PCIE Storage under VMD 項目設定為 [Disabled]。 SATA RAID 支援因主機板型號不同而異。請務必確認產品規格以獲得更多資訊。 1-6 4. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。 5.
3.1 建立 RAID 設定 請依照下列步驟建立 RAID 設定: 1. 從 Intel® Rapid Storage Technology 選單中選擇 Create RAID Volume 然後按下 按 鍵,會出現如下圖所示的視窗畫面。 2. 在 Name 的提示框中為您的 RAID 磁區輸入一個名稱,然後按下 按鍵。 3. 在 RAID Level 的提示框中按下 按鍵來選擇您想要的 RAID 層級,然後按下 按鍵。 4.
5. 在 Strip Size 的提示對話框中按下 按鍵來選擇 RAID 磁碟陣列(RAID 0、RAID 10 、RAID 5)要分割的容量,然後按下 按鍵。分割的數值可由 4 KB 遞增至 128 KB, 資料分割的數值應該以硬碟使用的目的來決定。下列為建議選項: - RAID 0: 128 KB - RAID 10: 64 KB - RAID 5: 64 KB 若此系統欲作為伺服器使用,建議您選擇較低的磁區大小;若此系統欲作為多媒體電腦用來 執行影音的編輯製作,建議您選擇較高的磁區大小來獲得更佳的效能。 1-8 6. 在 Capacity(MB) 的提示對話框中輸入您所要的陣列容量,接著按下 按鍵。本項 目預設值是採用最高可容許的磁碟容量。 7. 在 Create Volume 的提示對話框中再按下 按鍵來建立磁碟陣列,然後回到 Intel® Rapid Storage Technology 選單。 8. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。 9.
同時也會出現在 EZ Mode 選單中。 Intel® RAID 設定使用手冊 1-9
3.2 刪除 RAID 陣列 當您要刪除 RAID 設定時請小心,儲存在硬碟中的資料會被全部刪除。 請依照以下步驟刪除 RAID 陣列: 1-10 1. 從 Intel® Rapid Storage Technology 選單中選擇您想要刪除的 RAID 設定,然後按下 按鍵,會出現如下圖所示的視窗畫面。 2. 在 Delete 的提示對話框中按下 按鍵。 3.
4. 於 BIOS 中建立 SATA RAID 設定 有些 BIOS 選項可能不同,但步驟維持不變。 1. 將 VROC 金鑰安裝至主機板。 關於 VROC 金鑰插槽的位置,請參考主機板使用手冊。 2. 開啟主機板電源,並在啟動自我檢測程序(Power-On Self Test,POST)時,進入 BIOS 設定程式。 關於如何在 BIOS 中針對選單進行瀏覽與輸入,請參考主機板 BIOS 手冊中的相關說明。 3. 選擇 Platform Config > PCH 設定 > PCH 儲存設定 > Controller SATA and RST Configuration(控制器 SATA 與 RST 設定) 4. 將 SATA Mode Selection 項目設定為 [RAID]。 5. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。 6.
4.1 建立 RAID 設定 請依照下列步驟建立 RAID 設定: 1-12 1. 從 Intel® VROC SATA Controller 選單中選擇 Create RAID Volume 然後按下 按鍵, 會出現如下圖所示的視窗畫面。 2. 在 Name 的提示框中為您的 RAID 磁區輸入一個名稱,然後按下 按鍵。 3. 在 RAID Level 的提示框中按下 按鍵來選擇您想要的 RAID 層級,然後按下 按鍵。 4.
5. 在 Strip Size 的提示對話框中按下 按鍵來選擇 RAID 磁碟陣列(RAID 0、RAID 10 、RAID 5)要分割的容量,然後按下 按鍵。分割的數值可由 4 KB 遞增至 128 KB, 資料分割的數值應該以硬碟使用的目的來決定。下列為建議選項: - RAID 0: 128 KB - RAID 10: 64 KB - RAID 5: 64 KB 若此系統欲作為伺服器使用,建議您選擇較低的磁區大小;若此系統欲作為多媒體電腦用來 執行影音的編輯製作,建議您選擇較高的磁區大小來獲得更佳的效能。 6. 在 Capacity(GB) 的提示對話框中輸入您所要的陣列容量,接著按下 按鍵。本項 目預設值是採用最高可容許的磁碟容量。 7. 選擇 Create Volume 項目,接著在確認畫面中按下 Yes 以建立 RAID 設定。 建立磁碟陣列將會刪除所選硬碟中的所有資料。請確認在建立磁碟陣列前已備份硬碟中的 資料。 8.
4.2 刪除 RAID 陣列 當您要刪除 RAID 設定時請小心,儲存在硬碟中的資料會被全部刪除。 請依照以下步驟刪除 RAID 陣列: 1-14 1. 從 Intel® VROC SATA Controller 選單中選擇您想要刪除的 RAID 設定。 2. 選擇 Delete 項目。 3.
5. 於 UEFI BIOS 中使用內建 M.2 模組以建立 NVMe RAID 設定 • • 1. 您可以使用以下方式建立 RAID 設定: - 來自 CPU 的 NVMe SSDs。 - 來自 PCH 的 NVMe SSDs。 - 來自 CPU 與 PCH 的 NVMe SSDs。 - 第三方儲存裝置。 PCIe RAID 支援因主機板型號不同而異。請務必確認產品規格以獲得更多資訊。 在啟動自我檢測程序(Power-On Self Test,POST)時,進入 BIOS 設定程式。 關於如何在 BIOS 中針對選單進行瀏覽與輸入,請參考主機板 BIOS 手冊中的相關說明。 2. 選擇 Advanced(進階)選單 > System Agent(SA)設定 > VMD 設定選單。 3.
4. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。 5. 選擇 Advanced(進階)選單 > Intel(R)Rapid Storage Technology 選項以顯示 Intel® Rapid Storage Technology 選單。 5.1 建立 RAID 設定 請依照下列步驟建立 RAID 設定: 1. 從 Intel® Rapid Storage Technology 選單中選擇 Create RAID Volume。 2. 在 Name 的提示框中為您的 RAID 磁區輸入一個名稱,然後按下 按鍵。 3. 在 RAID Level 的提示框中按下 按鍵來選擇您想要的 RAID 層級,然後按下 按鍵。 4.
5. 在 Strip Size 的提示對話框中按下 按鍵來選擇 RAID 磁碟陣列(RAID 0、RAID 10、RAID 5)要分割的容量,然後按下 按鍵。分割的數值可由 4KB 遞增至 128KB,資料分割的數值應該以硬碟使用的目的來決定。下列為建議選項: - RAID 0: 128 KB - RAID 10: 64 KB - RAID 5: 64 KB 若此系統欲作為伺服器使用,建議您選擇較低的磁區大小;若此系統欲作為多媒體電腦用來 執行影音的編輯製作,建議您選擇較高的磁區大小來獲得更佳的效能。 6. 在 Capacity(MB) 的提示對話框中輸入您所要的陣列容量,接著按下 按鍵。本項 目預設值是採用最高可容許的磁碟容量。 7. 在 Create Volume 的提示對話框中建立磁碟陣列,然後回到 Intel® Rapid Storage Technology 選單。 8. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。 9.
同時也會出現在 EZ Mode 選單中。 5.2 刪除 RAID 陣列 當您要刪除 RAID 設定時請小心,儲存在硬碟中的資料會被全部刪除。 請依照以下步驟刪除 RAID 陣列: 1.
2. 在 Delete 的提示對話框中按下 按鍵。 3.
6. 於 BIOS 中使用內建 M.2/PCIe 儲存模組以建立 NVMe RAID 設定 • • 1. 您可以使用以下方式建立 RAID 設定: - 來自 CPU 的 NVMe SSDs。 - 來自 PCH 的 NVMe SSDs。 - 來自 CPU 與 PCH 的 NVMe SSDs。 - 第三方儲存裝置。 PCIe RAID 支援因主機板型號不同而異。請務必確認產品規格以獲得更多資訊。 將 VROC 金鑰安裝至主機板。 關於 VROC 金鑰插槽的位置,請參考主機板使用手冊。 2. 開啟主機板電源,並在啟動自我檢測程序(Power-On Self Test,POST)時,進入 BIOS 設定程式。 關於如何在 BIOS 中針對選單進行瀏覽與輸入,請參考主機板 BIOS 手冊中的相關說明。 3. 選擇 Advanced(進階)選單 > Sytem Storage Configuration for VROC 4. 根據安裝的儲存裝置,將 M.
5. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。 6. 選擇 Advanced(進階)選單 > Intel(R)Virtual RAID on CPU 選項以顯示 Intel® Virtual RAID on CPU 選單。 6.1 建立 RAID 設定 請依照下列步驟建立 RAID 設定: 1. 從 Intel® Virtual RAID on CPU 選單中,選擇 All Intel VMD Controllers。 2.
3. 在 Name 的提示框中為您的 RAID 磁區輸入一個名稱,然後按下 按鍵。 4. 在 RAID Level 的提示框中按下 按鍵來選擇您想要的 RAID 層級,然後按下 按鍵。 5. 在 Enable RAID Spanned over VMD Controllers 的提示框中按下 按鍵,並選擇 X 以啟用跨越 VMD 控制器的 RAID。這僅用於 Data RAID,不支援開機。 6.
7. 在 Strip Size 的提示對話框中按下 按鍵來選擇 RAID 磁碟陣列(RAID 0、RAID 10 、RAID 5)要分割的容量,然後按下 按鍵。分割的數值可由 4KB 遞增至 128KB, 資料分割的數值應該以硬碟使用的目的來決定。下列為建議選項: - RAID 0: 128 KB - RAID 10: 64 KB - RAID 5: 64 KB 若此系統欲作為伺服器使用,建議您選擇較低的磁區大小;若此系統欲作為多媒體電腦用來 執行影音的編輯製作,建議您選擇較高的磁區大小來獲得更佳的效能。 8. 在 Capacity(GB) 的提示對話框中輸入您所要的陣列容量。本項目預設值是採用最高可容 許的磁碟容量。 9. 選擇 Create Volume 項目,接著在確認畫面中按下 Yes 以建立 RAID 設定。 建立磁碟陣列將會刪除所選硬碟中的所有資料。請確認在建立磁碟陣列前已備份硬碟中的 資料。 10.
6.2 刪除 RAID 陣列 當您要刪除 RAID 設定時請小心,儲存在硬碟中的資料會被全部刪除。 請依照以下步驟刪除 RAID 陣列: 1-24 1. 從 Intel® Virtual RAID on CPU 選單中選擇您想要刪除的 RAID 設定。 2. 選擇 Delete 項目。 3.
7. 在 UEFI BIOS 中使用擴充 M.2 卡以建立 NVMe RAID 設定 部分 BIOS 選項可能會有所不同,但步驟相同。 1. 在啟動自我檢測程序(Power-On Self Test,POST)時,進入 BIOS 設定程式。 關於如何在 BIOS 中針對選單進行瀏覽與輸入,請參考主機板 BIOS 手冊中的相關說明。 2. 選擇 Advanced(進階)選單 > System Agent(SA)設定 > VMD 設定選單。 3.
4. 1-26 選擇 Advanced(進階)選單 > Onboard Devices Configuration(內建裝置設定),將 PCIEX16 設定為 [Dual M.2]。 • 關於 Hyper M.2 卡設定的更多訊息,請參考支援網站或主機板使用手冊。 • PCIEX16 設定選項可能會因型號而有所不同,請參考您主機板的實際 BIOS 以獲取正確 的項目。 5. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。您可以檢查在 EZ 模式 下,是否有正確識別 Hyper M.2 卡與安裝的 M.2 模組。 6.
7.1 建立 RAID 設定 請依照下列步驟建立 RAID 設定: 1. 從 Intel® Rapid Storage Technology 選單中選擇 Create RAID Volume 然後按下 按 鍵,會出現如下圖所示的視窗畫面。 2. 在 Name 的提示框中為您的 RAID 磁區輸入一個名稱,然後按下 按鍵。 3. 在 RAID Level 的提示框中按下 按鍵來選擇您想要的 RAID 層級,然後按下 按鍵。 4.
5. 在 Strip Size 的提示對話框中按下 按鍵來選擇 RAID 磁碟陣列(RAID 0、RAID 10、RAID 5)要分割的容量,然後按下 按鍵。分割的數值可由 4KB 遞增至 128KB,資料分割的數值應該以硬碟使用的目的來決定。下列為建議選項: - RAID 0: 128 KB - RAID 10: 64 KB - RAID 5: 64 KB 若此系統欲作為伺服器使用,建議您選擇較低的磁區大小;若此系統欲作為多媒體電腦用來 執行影音的編輯製作,建議您選擇較高的磁區大小來獲得更佳的效能。 1-28 6. 在 Capacity(MB) 的提示對話框中輸入您所要的陣列容量,接著按下 按鍵。本項 目預設值是採用最高可容許的磁碟容量。 7. 在 Create Volume 的提示對話框中再按下 按鍵來建立磁碟陣列,然後回到 Intel® Rapid Storage Technology 選單。 8. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。 9.
同時也會出現在 EZ Mode 選單中。 7.2 刪除 RAID 陣列 當您要刪除 RAID 設定時請小心,儲存在硬碟中的資料會被全部刪除。 請依照以下步驟刪除 RAID 陣列: 1.
1-30 2. 在 Delete 的提示對話框中按下 按鍵。 3.
8. 在 BIOS 中使用擴充 M.2 卡以建立 NVMe RAID 設定 有些 BIOS 選項可能不同,但步驟維持不變。 1. 將 VROC 金鑰安裝至主機板。 關於 VROC 金鑰插槽的位置,請參考主機板使用手冊。 2. 開啟主機板電源,並在啟動自我檢測程序(Power-On Self Test,POST)時,進入 BIOS 設定程式。 關於如何在 BIOS 中針對選單進行瀏覽與輸入,請參考主機板 BIOS 手冊中的相關說明。 3. 選擇 Advanced(進階)選單 > System Storage Configuration for VROC(VROC 系統儲 存設定)。 4. 將具有擴充 M.
5. 選擇 Advanced(進階)選單 > Onboard Devices Configuration(內建裝置設定)。 6. 將您安裝 M.2 擴充卡插槽的 PCIe 插槽設定為 [PCIe Bifurcation Mode]。 • 1-32 PCIe 插槽設定選項可能會因型號而有所不同,請參考您主機板的實際 BIOS 以獲取正確 的項目。 7. 儲存您的設定值並退出 BIOS 程式,然後再次進入 BIOS 程式。 8.
8.1 建立 RAID 設定 請依照下列步驟建立 RAID 設定: 1. 從 Intel® Virtual RAID on CPU 選單中選擇 All Intel VMD Controllers。 2.
3. 在 Name 的提示框中為您的 RAID 磁區輸入一個名稱,然後按下 按鍵。 4. 在 RAID Level 的提示框中按下 按鍵來選擇您想要的 RAID 層級,然後按下 按鍵。 5. 在 Enable RAID Spanned over VMD Controllers 的提示框中按下 按鍵,並選擇 X 以啟用跨越 VMD 控制器的 RAID。這僅用於 Data RAID,不支援開機。 6.
7. 在 Strip Size 的提示對話框中按下 按鍵來選擇 RAID 磁碟陣列(RAID 0、RAID 10、RAID 5)要分割的容量,然後按下 按鍵。分割的數值可由 4KB 遞增至 128KB,資料分割的數值應該以硬碟使用的目的來決定。下列為建議選項: - RAID 0: 128 KB - RAID 10: 64 KB - RAID 5: 64 KB 若此系統欲作為伺服器使用,建議您選擇較低的磁區大小;若此系統欲作為多媒體電腦用來 執行影音的編輯製作,建議您選擇較高的磁區大小來獲得更佳的效能。 8. 在 Capacity(GB) 的提示對話框中輸入您所要的陣列容量。本項目預設值是採用最高可容 許的磁碟容量。 9. 選擇 Create Volume 項目,接著在確認畫面中按下 Yes 以建立 RAID 設定。 建立磁碟陣列將會刪除所選硬碟中的所有資料。請確認在建立磁碟陣列前已備份硬碟中的 資料。 10.
8.2 刪除 RAID 陣列 當您要刪除 RAID 設定時請小心,儲存在硬碟中的資料會被全部刪除。 請依照以下步驟刪除 RAID 陣列: 1-36 1. 從 Intel® Virtual RAID on CPU 選單中選擇您想要刪除的 RAID 設定。 2. 選擇 Delete 項目。 3.
9. 於 Windows® 10 作業系統與 Windows® 11 作業系統安裝時安 裝 RAID 控制器驅動程式 在建立 RAID 後,您可以開始安裝作業系統至個別的磁碟或可啟用陣列(bootable array)。以 下部分提供如何在作業系統安裝時安裝 RAID 控制器驅動程式的說明。 以下的步驟與螢幕截圖僅供參考,可能會隨時因 Windows 更新而改變。 若您建立了 SATA RAID,則在加載 RAID 驅動程式前,將無法使用連接至 SATA 連接埠的光 碟機。 請依照下列步驟於 Windows® 10 作業系統或 Windows® 11 作業系統安裝時安裝 RAID 控制器驅 動程式: 1. 使用 Windows® 10 作業系統或 Windows® 11 作業系統安裝光碟以啟動電腦。您可以依照視 窗操作畫面開始安裝 Windows®。 2. 當出現安裝類型選項時,點選 Custom:Install Windows only (advanced)。 3.
1-38 4. 此訊息對話框為提醒您插入含有 RAID 控制器驅動程式的安裝媒體。點選 Browse 以進行 下一步。 5. 找到位在主機板驅動程式與應用程式光碟的對應資料夾中的驅動程式,然後點選 OK 以 進行下一步。 6. 從列表中選擇 RAID 控制器驅動程式,然後點選 Next。 7. 當系統下載完 RAID 驅動程式後,選擇欲安裝 Windows 的磁碟,然後點選 Next。 8.