User’s Manual
Table Of Contents
- About this guide
- Chapter 1: Getting Started
- Chapter 2: Main Menu Overview
- Chapter 3: Deploy Management
- 3.1 Agent Management overview
- 3.2 Deploying agents
- 3.2.1 Automatically scanning and deploying to devices
- 3.2.2 Scanning an IP range
- 3.2.3 Adding and deploying to devices
- 3.2.4 Editing device information
- 3.2.5 Installing Agents manually
- 3.2.6 Installing Agents in silent mode
- 3.2.7 Upgrading older versions of agents or repairing agents
- 3.2.8 Setting up a Windows 7 deployment environment
- 3.3 Removing agents
- 3.4 Client Agent Updater
- Chapter 4: Device Information
- Chapter 5: Management Functions
- 5.1 Metadata Management
- 5.2 Software Management
- 5.3 Task Scheduler
- 5.4 OOB Control
- 5.5 Management Control Overview
- 5.6 Management Control Information Overview
- 5.7 DASH Management Control Information
- 5.8 RTL8117 Management Control Information
- 5.9 vPro Management Control Information
- 5.10 BMC Management Control Information
- 5.10.1 Hardware Sensor
- 5.10.2 Inventory
- 5.10.3 Control
- 5.10.4 Remote Desktop
- 5.10.5 Smart BIOS
- 5.10.6 Firmware Update
- 5.10.7 Event Log
- 5.10.8 IPMI
- 5.10.9 IPMI Serial-over-LAN (SOL)
- 5.10.10 Settings
- 5.10.11 Configuration
- 5.10.12 FRU Information
- 5.10.13 Image Redirection
- 5.10.14 Platform Event Filters
- 5.10.14 BSOD Capture
- 5.11 Screen Broadcast
- Chapter 6: Settings Migrator
- Chapter 7: Report Generator
- Chapter 8: Account & General Settings
5-36 Chapter 5: Management Functions
Action
Category
Action type Action options Description
DASH*
Power
Control
Restart Computer to
IDE-R CDROM
Enter IDE-R ODD after restarting
device
Power On to IDE-R
CDROM
Enter IDE-R ODD after powering on
device
Sleep - Light (G1/S2) Enter sleep mode (G1/S2)
Power Cycle -
Hard Off (G3)
Restart device after forcing device to
power off.
Diagnostic Interrupt
(NMI)
Print error report and restarting device
Power Off - Soft
Graceful (G2/S5)
Normal shut down via the OS
Power Off - Hard
Graceful (G3)
Normal shut down via the hardware
Master Bus Reset
Graceful
Normal shut down and resetting the
hardware
Power Cycle (Graceful
Soft Off) (G2/S5)
Normal shut down via the OS then
restarting the device
Power Cycle (Graceful
Hard Off) (G3)
Normal shut down via the hardware
then restarting the device
vPro*
Power
Control
Power On (G0/S0) Power on device
Power Cycle -
Soft off (G2/S5)
Restart device after shutting down the
OS
Master Bus Reset Reset the hardware
Sleep - Deep (G1/S3) Enter sleep mode (G1/S3)
Hibernate (G1/S4) Enter hibernate mode (G1/S4)
Power Off -
Soft (G2/S5)
Power off device
Power Off - Soft
Graceful (G2/S5)
Normal shut down via the OS
Master Bus Reset
Graceful
Normal shut down and resetting the
hardware
Restart Computer to
BIOS
Enter BIOS after restarting device
Power On to BIOS Enter BIOS after powering on device
Restart Computer to
IDE-R Floppy
Enter IDE-R floppy drive after
restarting device
Power On to IDE-R
Floppy
Enter IDE-R floppy drive after powering
on device
Restart Computer to
IDE-R CDROM
Enter IDE-R ODD after restarting
device
Power On to IDE-R
CDROM
Enter IDE-R ODD after powering on
device
* These Action Categories are only supported on motherboards which support remote management controllers.