PA279CRV Series LCD Monitor User Guide
First Edition December 2022 Copyright © 2022 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Contents Contents....................................................................................................... iii Notices.......................................................................................................... iv TCO certified................................................................................................ vi Safety information...................................................................................... vii Care & Cleaning.................................
Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
NOTE: Energy Star is NOT supported on FreeDOS and Linux-based operating system. Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. This class B digital apparatus complies with Canadian ICES-003. This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment Regulations.
TCO certified A third-party certification according to ISO 14024 Toward sustainable IT products Say hello to a more sustainable product IT products are associated with a wide range of sustainability risks throughout their life cycle. Human rights violations are common in the factories. Harmful substances are used both in products and their manufacture. Products can often have a short lifespan because of poor ergonomics, low quality and when they are not able to be repaired or upgraded.
Safety information • Before setting up the monitor, carefully read all the documentation that came with the package. • To prevent fire or shock hazard, never expose the monitor to rain or moisture. • Never try to open the monitor cabinet. The dangerous high voltages inside the monitor may result in serious physical injury. • If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
AEEE yönetmeliğine uygundur Care & Cleaning • Before you lift or reposition your monitor, it is better to disconnect the cables and power cord. Follow the correct lifting techniques when positioning the monitor. When lifting or carrying the monitor, grasp the edges of the monitor. Do not lift the display by the stand or the cord. • Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor surface with a lint-free, non-abrasive cloth.
Where to find more information Refer to the following sources for additional information and for product and software updates. 1. ASUS websites The ASUS websites worldwide provide updated information on ASUS hardware and software products. Refer to http://www.asus.com 2. Optional documentation Your product package may include optional documentation that may have been added by your dealer. These documents are not part of the standard package.
x
1.1 Welcome! Chapter 1: Product introduction Thank you for purchasing the ASUS® LCD monitor! The latest widescreen LCD monitor from ASUS provides a broader, brighter and crystal-clear display, plus a host of features that enhance your viewing experience. With these features, you can enjoy the convenience and delightful visual experience that the monitor brings to you! 1.
1.3 Monitor introduction 1.3.1 Front view 1 1. 3 4 5 6 7 Power button/power indicator • Turns the monitor on/off. Press and hold this button for 0.6 seconds will shut down the monitor. • The color definition of the power indicator is as the below table. 2. Status Description White Amber Off On Standby mode Off QuickFit Plus button: • • Press this button to display the OSD menu when the OSD is off. Selects the QuickFit Plus function. Signal button: 3.
4. Shortcut 2 • Press this button to display the OSD menu when the OSD is off. • Default: Brightness hotkey • To change the hotkey function, go to the Shortcut > Shortcut 2 menu. Shortcut 1 5. • Press this button to display the OSD menu when the OSD is off. • Default: Energy Saving hotkey • To change the hotkey function, go to the Shortcut > Shortcut 1 menu. Exit button: 6. • Press this button to display the OSD menu when the OSD is off. • Exits the OSD menu. Menu (5-way) button: 7.
1.3.2 Back view 96W 96W 1 2 3 4 5 6 7 8 9 10 15W 15W 10 11 1. Kensington lock slot. 2. Power switch: Press the switch to turn on/off power. 3. AC-IN port: This port connects the power cord. 4. HDMI-1 port: This port is for connection with an HDMI compatible device. 5. HDMI-2 port: This port is for connection with an HDMI compatible device. 6. DisplayPort in: This port is for connection with a DisplayPort compatible device. 7.
1.3.3 Other Function(s) 1. Daisy chaining (for selected models) The monitor supports daisy chain on DisplayPort and USB Type-C. Daisy Chaining allows up to 4 monitors to be connected in series with the video signal being passed from the source to a monitor (when the input source is 3840 x 2160@60Hz and no USB-C device is connected). In order to enable daisy chaining, please make sure the source transported. This function is only available when Power Saving is Normal Level.
Chapter 2: Setup 2.1 Assembling the monitor arm/base To assemble the monitor base: 1. Make sure the triangle marks of VESA cover aligned. 2. Attach the arm into the VESA cover. 3. Shut the lock to make the arm and VESA cover assembled. 4. Have the front of the monitor face down on a table, slide the tabs on the arm into the slots on the VESA cover. 5. Press down the arm assembly to snap it into place. 6.
2.2 Detaching the arm/base (for VESA wall mount) The detachable arm/base of this monitor is specially designed for VESA wall mount. To detach the arm/base: 1. Have the front of the monitor face down on a table. 2. Press the release button, and then detach the arm/base from the monitor (Figure 1). 2 1 We recommend that you cover the table surface with soft cloth to prevent damage to the monitor. 2-2 • The VESA wall mount kit (100 x 100 mm) is purchased separately.
2.3 Adjusting the monitor • For optimal viewing, we recommend that you look at the full face of the monitor, then adjust the monitor to the angle that is most comfortable for you. • Hold the stand to prevent the monitor from falling when you change its angle. • You can adjust the monitor’s angle from +23˚ to -5˚, +/- 30˚ swivel adjustment from either left or right, and it allows +/- 90˚ pivot adjustment. You can also adjust the monitor’s height within +/- 130 mm.
2.4 Connecting the cables Connect the cables as the following instructions: 96W 96W 15W 15W • To connect the power cord: Connect one end of the power cord securely to the monitor’s AC input port, the other end to a power outlet. • To connect the HDMI/DisplayPort/USB Type-C* cable: a. Plug one end of the HDMI/DisplayPort/USB Type-C* cable to the monitor’s HDMI/DisplayPort/USB Type-C jack. b.
2.5 Turning on the monitor Press the power button . See page 1-2 for the location of the power button. The power indicator lights up in white to show that the monitor is ON.
3.1 OSD (On-Screen Display) menu 3.1.1 How to reconfigure PA279CRV 3840 x 2160_60Hz Preset Native Mode Signal DisplayPort Brightness 50 Native Mode Preset sRGB Mode Adobe RGB Mode Palette Rec.2020 Mode DCI-P3 Mode Image DICOM Mode Rec.709 Mode PIP/PBP HDR QuickFit Plus Back Enter Exit 1. Press any button to display the OSD menu. 2. Press the 3. Menu (5-way) button up/down/left/right to navigate through the Move the functions.
Chapter 3: General 3.1.2 OSD function introduction instructions 1. Preset This function contains 10 sub-functions you can select for your preference. Each mode has the Reset selection, allowing you to maintain your setting or return to the preset mode. PA279CRV 3840 x 2160_60Hz Preset Palette Image PIP/PBP Preset Native Mode Signal DisplayPort Brightness 50 Native Mode sRGB Mode Adobe RGB Mode Rec.2020 Mode DCI-P3 Mode DICOM Mode Rec.
Below table shows the default configurations for each ProArt Preset mode: Function Color Temp. Native Mode 6500K Brightness 50 Contrast 80 sRGB Mode Adobe RGB Mode Rec.
2. Palette Set a desired color setting from this menu. Preset Native Mode PA279CRV 3840 x 2160_60Hz Preset Palette Image PIP/PBP Brightness 50 Contrast 80 Saturation 50 Hue 50 Signal DisplayPort Brightness 50 Color Temp. Gamma RGB Tuning Black Level QuickFit Plus Back Exit • Brightness: The adjusting range is from 0 to 100. • Contrast: The adjusting range is from 0 to 100. • Saturation: The adjusting range is from 0 to 100. • Hue: Shifts the image color between green and purple.
3. Image Set the image related setting from this menu. Preset Native Mode PA279CRV 1080 60Hz Preset Palette Image Sharpness 0 Trace Free 60 Signal DisplayPort Brightness 50 Aspect Control Input Range Blue Light Filter 0 PIP/PBP QuickFit Plus Back Enter • Sharpness: The adjusting range is from 0 to 100. • Trace Free: Adjusts the response time of the monitor. Exit To activate this function, you need to do the following: turn off PIP/PBP and disable HDR on your device.
4. PIP/PBP The PIP/PBP menu allows you to open up another sub-window connected from another video source (when input source is below 60Hz) besides the main-window from your original video source. To activate this function, you need to do the following: turn off MediaSync/ VRR/Dynamic Dimming and disable HDR on your device.
5. QuickFit Plus In this function, you can use different kinds of alignment patterns. To activate this function, you need to do the following: turn off PIP/PBP, disable HDR on your device and restore your screen back to normal position (do not rotate).
6. Signal In this function, you can select your desired input source. PA279CRV 3840 x 2160_60Hz Preset Native Mode Signal DisplayPort Brightness 50 HDMI 1 Signal HDMI 2 DisplayPort Settings USB Type-C Auto Detection Shortcut Back • Enter Exit Auto Detection: automatically detects other active signals when current input signal is inactive. To activate this function, you need to do the following: remove the connection of Daisy-Chain DisplayPort output (to disable MST output).
7. Settings Allows you to adjust the system. PA279CRV 3840 x 2160_60Hz Preset Native Mode Signal DisplayPort Brightness 50 Media sync Signal Dynamic Dimming Power Saving Settings OSD Setup Sound Shortcut DisplayPort Stream Key Lock Power Indicator Back • Enter Exit MediaSync: Turn on VESA MediaSync support. * MediaSync can only be activated within 48Hz ~ 60Hz. * For supported GPUs, minimum PC system and driver requirements, please contact the GPU manufactures.
• OSD Setup: * Adjusts the OSD Timeout from 10 to 120 seconds. * Enables or disables the DDC/CI function. * Adjusts the OSD background from Opaque to Transparent. * Enables or disables the OSD Auto Rotation function. To activate OSD Auto Rotation, you need to do the following: turn off PIP/PBP. • Sound: * Adjusts Volume from 0 to 100. * Mute or un-Mute the audio output. * Select audio input from PIP/PBP Sources. To activate Sound function, you need to do the following: turn on PIP/PBP.
8. Shortcut Defines the functions for Shortcut 1 and 2 buttons. PA279CRV 3840 x 2160_60Hz Preset Native Mode Signal DisplayPort Brightness 50 Shortcut 1 Signal Shortcut 2 Settings Shortcut Back • Enter Exit Shortcut 1/Shortcut 2: Selects a function for Shortcut 1 and 2 buttons. When a certain function is selected or activated, your shortcut key may not support. Available function choices for shortcut: Blue Light Filter, Brightness, HDR, Contrast, PIP/PBP, Color Temp.
3.2 Specifications summary Panel Type Panel size TFT LCD 27” (16:9, 68.47 cm) wide screen Max. Resolution Pixel pitch Brightness (Typ.) Contrast Ratio (Typ.) Viewing angle (H/V) CR>10 Display colors Response time ProArt Preset selection Auto adjustment Color temperature selection Analog input Digital input 3840 x 2160 0.1554 mm x 0.1554 mm 350 cd/m2 (SDR), 400 cd/m2 (HDR) 1000:1 178˚/178˚ Digital Output Earphone jack Audio input Speaker (Built-in) USB 3.
Multi-languages Accessories Compliance and Standards 22 languages (English, French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech, Croatian, Polish, Romanian, Hungarian, Turkish, Simplified Chinese, Traditional Chinese, Japanese, Korean, Thai, Indonesian, Persian, Ukrainian) Quick start guide, warranty card, power cord, HDMI cable (optional), DisplayPort cable (optional), USB C to C cable (optional), color calibration testing report, ProArt welcome card cTUVus, FCC, ICES-3, EPEAT Gold, CB,
3.3 Outline dimensions ASUS PA279CRV Outline Dimension *Unit: mm(inch) 5° Tilt: -5~23 Degree 23° 538.11 [21.19] 362.89 [14.29] 175.22 [6.90] 612.22 [24.10] 596.74 [23.49] 228 [8.98] 190 [7.48] 335.66 [13.21] 30 ° Swivel: +/-30 Degree 39 [1.54] 7.9 [0.31] 12.5[0.49] 130 [5.12] 361.9 [14.25] 382.35 [15.05] 408.11 [16.07] 175.22[6.90] 30° 50.00 [1.97] 100[3.94] 100[3.
3.4 Troubleshooting (FAQ) Problem Possible Solution Power LED is not ON • Press the button to check if the monitor is in the ON mode. • Check if the power cord is properly connected to the monitor and the power outlet. • Check if the power switch is ON. The power LED lights amber and there is • Check if the monitor and the computer are no screen image in the ON mode. • Make sure the signal cable is properly connected the monitor and the computer.
3.5 Supported operating modes Resolution Frequency Horizontal Vertical Frequency (KHz) Frequency (Hz) Pixel (MHz) 640 x 480 37.47(P) 59.94(N) 25.18 800 x 600 35.16(P) 56.25(P) 36 800 x 600 37.88(P) 60.32(P) 40 848 x 480 31.0(P) 60(P) 33.75 1024 x 768 48.36(N) 60.00(N) 65 1280 x 720 44.77(N) 60 74.5 1280 x 768 47.8(N) 60(N) 79.5 1280 x 800 49.7(N) 60(P) 84.5 1280 x 960 60.00(P) 60.00(N) 108 1280 x 1024 63.98(P) 60.02(P) 108 1366 x 768 47.712(P) 59.79(P) 85.
When the monitor is operating in the video mode (ie, not displaying data), the following high definition modes shall be supported in addition to standard definition video. Resolution 1920 x 1080p 1920 x 1080i 1440 x 480p 1440 x 576p 1280 x 720p 720 x 576p 720 x 480p 640 x 480p(VGA) 720(1440) x 576i 720(1440) x 480i Vertical Frequency (Hz) 24Hz 25Hz 30Hz 50Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 59.94Hz 60Hz 50Hz 50Hz 59.94Hz 60Hz 50Hz 59.94Hz 60Hz 59.94Hz 60Hz 50Hz 59.
