PA27A 系列 LCD 顯示器 使用手冊
第一版 2017 年 9 月 版權所有 © 2017 ASUSTeK COMPUTER INC. 保留所有權利。 在未取得 ASUSTeK COMPUTER INC.
目次 目次 ......................................................................................................... iii 注意事項 ....................................................................................................... iv 安全資訊 ....................................................................................................... vi 保養和清潔 ................................................................................................... vii Takeback Services...........................................
注意事項 聯邦通訊委員會聲明 本裝置符合 FCC 規定之第 15 篇。操作符合下列兩個條件: • 本裝置不會造成有害干擾,而且 • 本裝置會接受任何接收到的干擾,包括可能會影響裝置運作的干擾。 本設備通過測試並符合 FCC 規定之第 15 篇 B 級數位裝置的限制。這些限制的用 意在於提供適當防護,避免設備安裝在居住環境下產生有害干擾。本設備會產生、使 用和發射無線電頻能量,此外,若未依照製造商的指示安裝和使用,可能會對無線電 通訊產生不良干擾。然而,並不保證在特定安裝情況下不會產生干擾。若本設備對收 音機或電視機的收訊產生不良干擾(可開啟然後關閉設備電源判定),使用者可透過 以下方法消除干擾: • 重新調整接收天線的方向或位置。 • 增加設備和接收天線之間的距離。 • 將本設備連接到與接收器電源不同的電源插座上。 • 請向經銷商或有經驗的廣電技術人員尋求協助。 連接顯示器與顯示卡的遮蔽纜線,須符合 FCC 的規定。若未經相容性規定之相 關當局明示許可,擅自修改或改裝本裝置,使用者可能喪失操作本設備之權限。 符合 ENERGY STAR 標準的產品 ENERGY STAR 是美國環保署
加拿大通訊部聲明 本數位裝置未超過加拿大通訊部無線電干擾法規所規定之數位裝置無線電干擾發射 的 B 級限制。 本設備為符合加拿大 ICES-003 規範的 B 級數位裝置。 This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouiller du Canada.
安全資訊 • 設定本顯示器之前,請詳讀產品包裝內的說明文件。 • 為預防起火或觸電,請勿將顯示器置於雨中或潮溼環境中。 • 請勿試圖打開顯示器的機殼。顯示器內部的高壓電可能造成人員嚴重受傷。 • 若電源供應器損壞,請勿嘗試自行修復。請洽詢合格的維修技術人員您的零 售商。 • 使用本產品前,請確定已正確連接所有纜線,而且電源線並未損壞。若發現任何 損壞,請立刻聯絡您的經銷商。 • 機殼背面或頂端的開口和通風口係用於散熱。請勿堵塞這些開口。除非通風良好, 否則請勿將本產品置於靠近散熱器或熱源的位置或其上方。 • 本顯示器只能在產品標籤所示的電源環境下操作。若您不確定您家中的電源規 格,請洽詢您的經銷商或當地的電力公司。 • 使用符合當地電源標準的電源插頭。 • 不可使排插和延長線的電源過載。電源過載會導致起火或人員觸電。 • 避免在多灰塵、潮溼和極端溫度的環境中使用。請勿將顯示器置於可能會使其受 潮的區域。請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本機的電源插頭。如此可預防顯示器因電源 突波而損壞。 • 請勿讓任何物體或液體進入顯示器機殼的開口
保養和清潔 • 抬高或重新移位顯示器之前,請先拔下纜線和電源線。顯示器移位前,請依照正 確的抬高方法。抬高或移動顯示器時,請握住顯示器的邊緣。請勿以拉抬底座或 纜線的方式抬高顯示器。 • 清潔。關閉顯示器的電源,然後拔下電源線。使用無毛球且不會刮傷螢幕的布清 潔顯示器表面。可用沾有中性清潔劑的布清除頑垢。 • 避免使用含有酒精或丙酮的清潔劑。使用顯示器專用的清潔劑。請勿直接將清潔 劑噴灑於螢幕上,否則可能滲入顯示器內並造成人員觸電。 若顯示器發生以下情況,屬於正常現象: • 不同的桌面模式可能導致螢幕有輕微亮度不均的情況。 • 顯示同一幅影像數小時後,切換影像時可能會出現前張影像的殘影。殘影會慢慢 消失,或者您可以開關電源數小時消除此情況。 • 螢幕變黑、閃爍或完全無法運作時,請洽詢您的經銷商或服務中心進行修復。請 勿自行修理螢幕! 本手冊使用的慣語 警告:執行作業作時,避免人員受傷的資訊。 注意:執行作業時,避免零組件損壞的資訊。 重要:執行作業時「必須」遵守的資訊。 註:協助執行作業的提示和其他資訊。 vii
其他詳細資訊來源 如需其他資訊和產品與軟體的更新程式,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供有關 ASUS 硬體和軟體產品的最新資訊。請連至 http://www.asus.com 取得相關資訊。 2. 選用的說明文件 您的產品包裝內可能有經銷商所提供的選用說明文件。產品的標準包裝中不含 此類文件。 Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials. Please go to http://csr.asus.
TCO 認證 A third-party certification according to ISO 14024 Toward sustainable IT products Say hello to a more sustainable product IT products are associated with a wide range of sustainability risks throughout their life cycle. Human rights violations are common in the factories. Harmful substances are used both in products and their manufacture. Products can often have a short lifespan because of poor ergonomics, low quality and when they are not able to be repaired or upgraded.
x
1.1 歡迎使用! 感謝您購買 ASUS® LCD 顯示器! ASUS 最新的寬螢幕液晶顯示器提供更寬廣、更明亮和更清晰的顯示,以及許多可 增強觀看感受的功能。 您可藉由這些功能享受到本顯示器帶給您的便利與快樂的視覺體驗! 1.
1.3 顯示器介紹 1.3.1 正面圖 1 2 3 4 5 6 7 Menu Close Input Select QuickFit Brightness Blue Light Filter 1. 功能表(5 向)按鈕: • 按下此按鈕可進入 OSD 功能表。 • 啟用所選的 OSD 選單項目。 • 增加/減少值或向上/向下/向左/向右移動選擇。 2. 關閉按鈕: • 離開 OSD 功能表。 • 長按 5 秒即可開啟和關閉按鍵鎖功能。 • 選擇可用的輸入來源。 3. 輸入選擇按鈕: 將 HDMI/DisplayPort/Thunderbolt 訊號線連接到顯示器後,按下 按鈕 (輸入選擇按鈕)可顯示 HDMI-1、HDMI-2、HDMI-3 (HDR)、Thunderbolt 、 DisplayPort 訊號。Thunderbolt 是預設設定。如果要連接 DisplayPort 裝置, 請選擇 DisplayPort。 4.
5. 捷徑 • 預設值:亮度快速鍵 • 若要變更快速鍵功能,請至捷徑 > 捷徑 1 功能表。 6. 捷徑 • • 7. 預設值:濾藍光快速鍵 若要變更快速鍵功能,請至捷徑 > 捷徑 2 功能表。 電源按鈕/電源指示燈 • 開啟/關閉顯示器電源。 • 電源指示燈的顏色定義如下表所示。 1.3.2 狀態 說明 白色 琥珀色 關機 開機 待機模式 關機 背面圖 1 2 3 4 5 6 1. Kensington 鎖插槽。 2. 電源開關。按下開關以開啟 / 關閉電源。 3. AC-IN 連接埠。此連接埠用於連接電源線。 4. HDMI 連接埠。這些連接埠用於連接 HDMI 相容裝置。 7 8 9 10 11 HDMI-1 和 HDMI-2 連接埠支援 HDMI 1.4。HDMI-3 (HDR) 特別支援 HDR 解析 度的 HDMI 2.0a。 5. DisplayPort 輸入。此連接埠用於連接 DisplayPort 相容裝置。 在 OSD 功能表中的 DisplayPort 串流預設設定是 DisplayPort 1.
7. Thunderbolt。這些連接埠用於連接 Thunderbolt 相容裝置。這些連接埠可 加強資料傳輸、視訊輸出,以及充電到單一精簡接頭(連接埠 45W 的供電,而另一連接埠 提供最高 則是提供 15W。)。其中會將插入的第一個 連接埠辨識為輸入來源。另一個將做為 DisplayPort 訊號輸出,啟用後將支援 Thunderbolt 菊輪鍊。 8. USB 3.0 Type-C。此連接埠用於連接 USB 下載資料線。該連接支援 USB 電 源和資料傳輸。 本顯示器相容於 Super-Speed USB 3.0 (5Gbps)。具 合 BC1.2 標準。 9. 圖示的連接埠符 USB 3.0 Type A:這些連接埠用於連接 USB 鍵盤/滑鼠、USB 隨身碟等 USB 裝置。 10. USB 3.
2. A4 QuickFit 提供標準 A4 紙張大小,以供使用者在螢幕上檢視實際大小的文件。 A4 A4 3. B5 QuickFit 提供標準 B5 紙張大小,以供使用者在螢幕上檢視實際大小的文件。 B5 B5 4.
5. 尺規 此模式會在頂端和左側顯示實體尺規。您可以按下 上,切換公制與英制的測量單位。 功能表(5 向)按鈕 3 秒以 尺規 5 10 15 20 25 30 5 10 15 1.3.4 其它功能 1. HDR 顯示器支援 HDR 格式。偵測 HDR 內容時會彈出「HDR ON」(HDR(開啟))訊 息,並且在「顯示資訊」頁面中顯示。 • 顯示 HDR 內容時,無法使用以下功能: Splendid、色彩、影像(Trace Free、畫面控制、均勻度補償、Vividpixel、ASCR)、低藍光。 • 開啟 PIP/PBP 模式時,不支援 HDR 內容。 2.
2.1 安裝支架 / 底座 組裝顯示器底座: 1. 將顯示器正面朝下置於桌上。 2. 取下輸入 / 輸出連接埠蓋(圖 1)。 3. 將底座安裝於支架,確定支架的調整片卡入底座的溝槽(圖 2)。 2 1 (圖 2) (圖 1) 建議您使用軟布覆蓋桌子表面,避免顯示器受損。 2.2 拆開支架 / 底座(適用於 VESA 壁掛式安裝) 此顯示器的可拆式支架/底座是專為 VESA 壁掛式安裝所設計。 拆開支架/底座: 1. 將顯示器正面朝下置於桌上。 2. 取下輸入 / 輸出連接埠蓋(圖 1)。 3. 按下釋放鈕,然後將支架 / 底座自顯示器拉出(圖 2)。 2 1 (圖 1) (圖 2) 建議您使用軟布覆蓋桌子表面,避免顯示器受損。 • VESA 壁掛架套件(100 x 100 公釐)個別採購。 • 僅可使用最小重量 / 負荷 22.
2.
以顯示器為中心旋轉 1. 將顯示器抬升至最高位置。 2. 將顯示器傾斜至最大角度。 3. 以顯示器為中心旋轉至所需的角度。 +23° ~ -5° 調整觀看角度時,顯示器輕微震動是正常的情況。 4.
2.4 1. 接線 依下列指示連接訊號線: 僅供維修之用 • 連接電源線:將電源線的一端牢牢連接到顯示器的 AC 輸入埠,將另一端連接到 電源插座。 • 連接 HDMI/DisplayPort 訊號線: a. 將 HDMI/DisplayPort 訊號線的一端連接到顯示器的 HDMI/DisplayPort 插孔。 b. 將 HDMI/DisplayPort 訊號線的另一端連接到裝置的 HDMI/DisplayPort 插孔。 • 若要使用耳機:HDMI/DisplayPort/Thunderbolt 訊號輸入時,將插頭端連接到顯 示器的耳機插孔。 • 使用 USB 3.0 連接埠: » 上傳連接埠:取得隨附的 USB 3.0 訊號線,將 USB 上傳資料線較小的一 端(B 型)插入顯示器的 USB 資料上傳連接埠,並將較大的一端(A 型) 插入電腦的 USB 3.0 連接埠。請確保電腦已安裝最新版 Windows 7/ Windows 8.
2. 視需要安裝輸入 / 輸出連接埠蓋和 / 或束線夾。 2.
2-6 第 2 章: 設定
3.1 OSD(螢幕功能顯示)選單 3.1.1 如何重新設定 Splendid ASUS PA27A 標準模式 Thunderbolt 2560 x 1440@ 60Hz 標準模式 sRGB 模式 Rec. 709 模式 風景模式 閱讀模式 暗房模式 使用者模式 1 使用者模式 2 1. 按下 2. 上下左右移動 功能表(5 向)按鈕可瀏覽功能。反白顯示所需的功能,然 後按下 功能表(5 向)可啟動此功能。若所選的功能有子功能表,請上下 移動 功能表(5 向)按鈕可瀏覽子功能表功能。反白顯示所需的子功能表 功能,然後按下 功能表(5 向)按鈕,或移動 功能表(5 向)按鈕可 啟動此功能。 功能表(5 向)按鈕可啟動 OSD 功能表。 3. 上下移動 4.
3.1.2 1. OSD 功能介紹 Splendid 此功能包含 8 個子功能,您可依喜好自行選擇。各模式皆有重設選項,您可保 留現有的設定值或復原成預設模式。 若要啟動此功能,您需要進行以下動作:停用您裝置上的 HDR。 Splendid ASUS PA27A 標準模式 Thunderbolt 2560 x 1440@ 60Hz 標準模式 sR G B 模式 R ec. 709 模式 風景模式 閱讀模式 暗房模式 使用者模式 1 使用者模式 2 • 標準模式:搭配 Splendid 影像增強技術下,最適合用於文件編輯 情況。 標準模式符合 TCO 需求。 • sRGB 模式:sRGB 模式相容於 sRGB 色彩空間,最適合用於文件編輯。 sRGB 模式符合 Energy Star® 需求。 • Rec. 709 模式:相容於 Rec.
標準模式 sRGB 模式 功能 色溫 6500K 亮度 50 對比 80 固定 關機 啟用 固定 50 固定 50 停用 ASCR 影像銳利 彩度 色調 進階設定 黑階 啟用 Gamma 2. 固定 6500K 固定 50 固定 80 固定 關機 啟用 固定 50 固定 50 停用 停用 固定 2.2 2.2 均勻度補償 Rec. 709 使用者模式 1/ 風景模式 閱讀模式 暗房模式 模式 使用者模式 2 關機 關機 固定 6500K 6500K 50 100 80 固定 關機 啟用 80 關機 啟用 中 (50) 中 (50) 中 (50) 中 (50) 啟用 啟用 啟用 啟用 固定 2.2 固定 關機 2.2 關機 固定 6500K 固定 6500K 4 4 50 80 80 關機 關機 固定 80 固定 關機 啟用 固定 50 固定 50 停用 停用 啟用 啟用 中 (50) 中 (50) 中 (50) 中 (50) 啟用 停用 啟用 停用 固定 2.2 固定 關機 2.2 2.
3.
4. 影像 在此選單中設定影像相關設定。 若要啟動此功能,您需要進行以下動作:停用您裝置上的 HDR。 影像 ASUS PA27A 標準模式 Thunderbolt 2560 x 1440@ 60Hz 影像 銳 利 Trace Fre e 畫面 控 制 均勻 度 補 償 VividPixe l ASCR • 影像銳利:調整範圍為 0 到 100。 • Trace Free:調整顯示器的反應時間。 • 畫面控制:將長寬比調整成全螢幕、4:3、1:1 或 OverScan。 4:3 只能在輸入訊號源為 4:3 格式時使用。OverScan 僅可用於 HDMI 輸入訊 號源。 • 均勻度補償:調整畫面的不同區域,減低任何畫面均勻度錯誤,提供整個 畫面一致的亮度和色彩。 • VividPixel:強化所顯示圖片的輪廓,並在螢幕上產生高品質的影像。 • ASCR:可開啟/關閉 ASCR(ASUS 智慧對比比例)功能。 5.
6.
7. 輸入選擇 此功能可供您選擇所需的輸入來源。 輸入選擇 ASUS PA27A 標準模式 Thunderbolt 2560 x 1440@ 60Hz H D M I -1 H D M I -2 H D M I -3 ( H D R ) D is playP o r t T hunder b o l t 8.
• • 節能模式: * 「初級階層」能夠讓 USB 資料下載連接埠/Thunderbolt 連接埠在 顯示器進入節能模式時將外接裝置充電。 * 「深度階層」禁止所有連接埠將外接裝置充電,並避免顯示器進入 節能模式時自動偵測 DisplayPort 、 Thunderbolt 和USB訊號,藉 以達到最大的節能效益。 選單設定: * 調整 OSD 的逾時時間,範圍介於 10 至 120 秒。 * 啟用或停用 DDC/CI 功能。 * 將 OSD 背景從不透明調整至透明。 * 調整 OSD 旋轉。 • 語言:提供 21 種語言任您選擇,包括英文、法文、德文、義大利文、 西班牙文、荷蘭文、葡萄牙文、俄文、捷克文、克羅埃西亞文、波蘭文、 羅馬尼亞文、匈牙利文、土耳其文、簡體中文、繁體中文、日文、韓文、 泰文、印尼文、波斯文。 • DisplayPort 串流:相容於顯示卡。依顯示卡 DP 版本選擇 DisplayPort 1.1 或 DisplayPort 1.2。 DisplayPort 1.
9.
3.2 規格總覽 溫度(運作時) TFT LCD 27.0 吋(16:9、68.47 公分)寬螢幕 2560 x 1440 0.2331 公釐 350 cd/m2;最大 400 cd/m2 1000:1 100,000,000:1(ASCR 開啟時) 178˚/178˚ 1670 萬(8 位元) sRGB 100% 5 毫秒(灰階對灰階) 有 8 種影像預設模式 4 種色溫 HDMI v1.4、HDMI v2.0a、DisplayPort v1.2、 ThunderboltTM 3 有 2W x 2 立體聲,RMS 資料上傳連接埠 x 1、資料下載連接埠 x 3 灰色及黑色 白燈(開)/琥珀燈(待機) +23˚~ -5˚ +60˚~ -60˚ +90˚; -90˚ 120 公釐 有 AC:100 ~ 240 V 開機時:< 25 W**(一般)、待機:< 0.
配件 符合性與標準 HDMI 訊號線、DisplayPort 訊號線、Thunderbolt 訊號線、 電源線、USB 訊號線、快速使用指南、保固卡、支援光碟、 束線夾、色彩校正、測試報告、輸入/輸出連接埠蓋、色彩校 正器 (僅是用於 PA27AC-K) Energy Star®、UL/cUL、CB、CE、EuP、FCC、CCC、 BSMI、CU、VCCI、TCO、J-MOSS、RoHS、 WEEE、PSE、KCC、ICES-3、ErP、CEL、ISO 9241-307 、UkrSEPRO、RCM、MEPS、PC Recycle、KC、 e-Standby、TUV Flicker Free、TUV Low Blue Light、 Windows 7、8.1 和 10 WHQL、Mac Compliance*** *產品規格如有變更,恕不另行通知。 **螢幕亮度的測量值為 200 尼特,不含音訊/USB/讀卡機連線。 ***需安裝 Mac OS 10.10.x、10.11.x、10.12.
3.
3.4 支援的操作模式 解析度頻率 640x480 640x480 640x480 640x480 720x400 800x600 800x600 800x600 800x600 832x624 1024x768 1024x768 1024x768 1152x864 1280x960 1280x1024 1280x1024 1366x768 1440x900 1600x1200 1680x1050 1920x1080 1920x1200 (減少空白畫面 機率) 1920x1200 2560x1080 2560x1440 2560x1440* 水平頻率 (KHz) 31.47(N) 35.00(N) 37.87(N) 37.5(N) 31.47(N) 35.16(P) 37.88(P) 48.08(P) 46.86(P) 49.72(P/N) 48.36(N) 56.476(N) 60.02(N) 67.5(P/N) 60.00(P) 63.98(P) 79.98(P) 47.712(P) 55.94(N) 75.00(P) 65.29(N) 67.5(P) 垂直頻率 (Hz) 59.
AMD R9 270X、AMD R7 260X、AMD R7 250、AMD HD 7990、AMD HD 7970、AMD HD 7850、 AMD HD 7790、AMD HD 7770、AMD HD 6990、NVIDIA GTX 980、NVIDIA GTX 960、NVIDIA GTX TITAN Z、NVIDIA GTX 780、NVIDIA GTX 770、NVIDIA GTX 750 Ti、NVIDIA GTX 750、NVIDIA GTX 690、NVIDIA GTX 680、NVIDIA GTX 770、Intel HD Graphics 4400、Intel HD Graphics 4600。 時序名稱 480p 720p60 576p 720p50 1080p60 1080p50 3-14 像素格式 720 x 480 1280 x 720 720 x 576 1280 x 720 1920 x 1080 1920 x 1080 水平頻率 (kHz) 31.469 45 31.25 37.5 67.5 56.