PA27UCX 시리즈 LCD 모니터 사용 설명서
초판 2020 년 3 월 Copyright © 2020 ASUSTeK COMPUTER INC. All Rights Reserved. 이 설명서에 포함된 제품 및 소프트웨어를 비롯해 어떠한 부분도 ASUSTeK COMPUTER INC.(“ASUS”) 의 명시적인 서면 승인 없이 , 구매자가 백업할 목적으로 본 설명서를 보관하는 것 이외에 , 어떠한 형식이나 수단으로도 복사 또는 복제 , 전송 , 검색 시스템에 저장 또는 다른 언어로 번역할 수 없습니다 . 다음의 경우 제품 보증 또는 서비스가 연장되지 않습니다 : (1) 제품을 수리 , 변경하거나 개조한 경우 ( 그러한 수리 , 변경 , 개조를 ASUS 가 서면으로 승인하지 않을 때 ); 또는 (2) 제품의 일련 번호가 훼손되었거나 누락된 경우 . ASUS 는 이 설명서를 명시적 또는 묵시적으로 어떠한 종류의 보증도 없이 " 있는 그대로 " 제공합니다 . 이는 특정한 목적을 위한 상업성 또는 적합성에 대한 묵시적 보증이나 조건에도 적용됩니다 .
목차 목차 iii 고지 iv 안전 정보 ....................................................................................................... v 관리 및 청소 .................................................................................................. vi Takeback Services ..................................................................................... vii 1장: 제품 소개 1.1 환영합니다 ! .................................................................................. 1-1 1.2 포장 내용물 ....................................
고지 연방 통신 위원회 진술 이 장치는 FCC 규칙의 파트 15 를 준수합니다 . 작동은 다음 두 가지 조건을 따릅니다 : • 이 장치는 유해한 간섭을 일으키지 않습니다 . 또한 • 이 장치는 원치 않는 작동을 유발할 수 있는 간섭을 포함하여 모든 간섭을 수용해야 합니다 . 이 장치는 테스트를 거쳤으며 FCC 규칙의 파트 15 를 따르는 클래스 B 디 지털 장치에 대한 제한을 준수하는 것으로 확인되었습니다 . 이 제한은 주거 환경에 설치 시 유해한 간섭으로부터 합리적으로 보호할 목적으로 설계되 었습니다 . 이 장치는무선 주파수 에너지를 발생 , 사용 및 방출할 수 있습니 다 . 지침에 따라 설치 및 사용하지 않을 경우 , 무선 통신에 유해한 간섭을 일으킬 수 있습니다 . 그러나 , 특별 설치 시 간섭이 발생하지 않는다고 보장 하지는 않습니다 .
안전 정보 • 모니터를 설치하기 전에 패키지와 함께 제공된 모든 설명서를 주의깊게 읽어 보십시오 . • 화재 또는 감전 위험을 방지하려면 모니터를 비나 습기에 노출시키지 마십시오 . • 모니터 캐비닛을 절대로 열지 마십시오 . 모니터 내부의 위험한 고전압으로 인해 심각한 신체 상해를 입을 수 있습니다 . • 전원 공급 장치가 망가진 경우 직접 고치려고 시도하지 마십시오 . 자격이 있는 수리 기술자 또는 대리점에 연락하십시오 . • 제품을 사용하기 전에 모든 케이블이 제대로 연결되어 있는지 및 전원 케이블이 손상되지 않았는지 확인하십시오 . 손상된 부분이 발견되면 즉시 대리점에 연락하십시오 . • 뒷면의 슬롯과 구멍 또는 캐비닛의 위쪽은 통풍구입니다 . 이 슬롯을 막지 마십시오 . 적절한 통풍이 되지 않을 경우 라디에이터 또는 난방 장치 근처나 위에 이 제품을 놓지 마십시오 . • 이 모니터는 레이블에 표시된 유형의 전원에서만 작동해야 합니다 .
관리 및 청소 • 모니터를 들어올리거나 자리를 옮기기 전에 케이블과 전원 코드의 연결을 분리하는 것이 좋습니다 . 모니터의 위치를 바꿀 때 다음과 같이 하십시오 . 모니터를 들어올리거나 이동할 때는 모니터 가장자리를 잡으십시오 . 받침대나 코드를 잡고 디스플레이를 들어올리지 마십시오 . • 청소 . 모니터를 끄고 전원 코드를 뽑습니다 . 모니터 표면은 보풀이 없고 마찰을 일으키지 않는 천으로 닦으십시오 . 잘 지워지지 않는 얼룩은 천에 순한 클리너를 묻힌 후 닦아내십시오 . • 알코올이나 아세톤이 포함된 클리너는 사용하지 마십시오 . 모니터 전용 클리너를 사용하십시오 . 화면에 직접 클리너를 뿌리지 마십시오 . 모니터 안쪽으로 흘러들어가 전기 감전을 일으킬 수 있습니다 . 다음은 모니터에서 흔히 볼 수 있는 증상입니다: • 데스크탑 사용 패턴에 따라 화면의 밝기가 약간 고르지 못할 수 있습니다 .
추가적인 정보를 찾을 수 있는 곳 추가 정보 및 제품과 소프트웨어 업데이트에 대해서는 다음 소스를 참조하십시오 . 1. ASUS 웹사이트 ASUS 웹사이트에서는 ASUS 하드웨어와 소프트웨어 제품에 대한 업데이트 정보를 제공합니다 . http://www.asus.com 을 참조하십시오 . 2. 선택 사항 설명서 제품 패키지에는 대리점이 추가로 제공하는 선택 사항 설명서가 포함되어 있을 수 있습니다 . 이러한 설명서는 표준 패키지의 일부가 아닙니다 . Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment.
viii
1.1 환영합니다 ! ASUS® LCD 모니터를 구입해 주셔서 감사합니다 ! ASUS 의 최신 와이드스크린 LCD 모니터는 더 넓고 , 더 밝은 크리스탈 클리어 디스 플레이 뿐 아니라 보기 환경을 강화하는 많은 기능을 제공합니다 . 이러한 기능들을 통해 모니터가 선사하는 편리함과 생생한 비주얼을 즐길 수 있습 니다 ! 1.2 포장 내용물 패키지에서 다음 항목을 확인하십시오: LCD 모니터 모니터 받침 빠른 시작 설명서 보증 카드 전원 코드 HDMI 케이블 USB 타입 C 케이블 DisplayPort 케이블 USB 타입 C와 타입 A 연결 케이블 입력/출력 포트 커버 색 보정 테스트 보고서 색 보정기(PA27UCX-K에만 해당) 후드 위 항목 중에서 손상되거나 누락된 항목이 있으면 즉시 대리점에 문의하십시오.
1.3 모니터 소개 1.3.1 정면도 1 2 3 4 5 6 7 Menu Close Input Select QuickFit Brightness HDR 1. 메뉴 (5-방향) 단추: • 이 버튼을 눌러 OSD 메뉴를 시작합니다. • 선택한 OSD 메뉴 항목을 실행합니다. • 값을 증가/감소 또는 선택 항목을 위/아래/왼쪽/오른쪽으로 이동합니다. 2. 닫기 버튼: • OSD 메뉴를 종료합니다. • 5초 동안 길게 눌러 키 잠금 기능을 켜짐과 꺼짐 간에 전환합니다. • 사용 가능한 입력 소스를 선택합니다. 3. 입력 선택 버튼: HDMI/DisplayPort/USB 타입 C 케이블을 모니터에 연결 한 후 택 버튼)을 눌러 HDMI-1, HDMI-2, DisplayPort, USB 3.1 타입 C( 시합니다. 4. QuickFit 버튼: • 정렬을 위해 고안된 QuickFit 기능을 활성화하는 바로가기 키입니다.
• 6. 바로가기 키 기능을 변경하려면, 바로가기 키 > 바로가기 키 1 메뉴로 이 동합니다. 바로가기 키 2 • 기본: HDR 바로가기 키 • 바로가기 키 기능을 변경하려면, 바로가기 키 > 바로가기 키 2 메뉴로 이 동합니다. 7. 전원 단추/전원 표시기 • 모니터를 켜거나 끕니다. • 전원 표시기의 색상 정의가 아래 표에 나와 있습니다. 1.3.2 상태 설명 흰색 주황색 꺼짐 켜짐 대기 모드 꺼짐 후면 모습 1 11 2 3 4 5 6 7 8 9 10 1. 켄싱턴 잠금장치 슬롯 . 2. 전원 스위치 . 스위치를 눌러 전원을 켜거나 끕니다 . 3. AC 입력 포트 . 이 포트는 전원 코드를 연결합니다 . 4. HDMI 포트 . 이 포트는 HDMI 호환 장치와 연결하기 위한 포트입니다 . 5. DisplayPort 입력 . 이 포트는 DisplayPort 호환 장치와 연결하기 위한 포트입 니다 .
8. USB 타입 C2. 이 포트는 USB 3.1 타입 C의 전원 공급 기능을 활성화하기 위 해 전원 어댑터와 연결하기 위한 전용 포트입니다. 9. USB 3.1 타입 A(SuperSpeed USB 5 Gbps): 이 포트는 USB 키보드/마우스, USB 플래시 드라이브 등과 같은 USB 장치와 연결하기 위한 포트입니다. 10. 이어폰 잭. 11. 제어 버튼. 1.3.3 QuickFit 기능 QuickFit 기능에는 다음과 같은 7 가지 유형의 패턴이 있습니다 . (1) Alignment Grid (2) A4 (3) B5 (4) Letter (5) Photo (6) Customization (7) Ruler. 패턴을 활성화하려면 , QuickFit 버튼을 누릅니다 . 메뉴 (5- 방향 ) 버튼을 눌러 원하는 패턴을 선택합니 다 필요한 경우 위 / 아래 / 왼쪽 / 오른쪽 버튼을 이동하여 패턴의 위치를 변경할 수 있습니다 .
3. B5 QuickFit 은 사용자가 화면에서 문서를 실제 크기로 볼 수 있도록 표준 B5 용지 크기 를 제공합니다 . B5 B5 4. Letter QuickFit 은 사용자가 화면에서 문서를 실제 크기로 볼 수 있도록 표준 레터 용지 크 기를 제공합니다 . Letter Letter 5. 사진 크기 QuickFit 기능에서 실제 사진 크기를 다양하게 표시할 수 있어 사진 작가와 기타 사 용자들이 화면에서 사진을 정확하게 실제 크기로 보고 편집할 수 있습니다 .
6. Customization 메뉴 (5 방향 ) 버튼을 위 / 아래 / 왼쪽 / 오른쪽으로 움직여 프레임 크기를 결정할 수 있습니다 . 메뉴 (5 방향 ) 버튼을 3 초 이상 눌러 측정 단위를 밀리미터와 인치 로 전환할 수 있습니다 . Customization H16 V15 7. Ruler 이 패턴은 상단과 왼쪽에 실제 눈금자를 표시합니다 . 메뉴 (5 방향 ) 버튼을 3 초 이상 눌러 측정 단위를 미터법과 야드파운드법으로 전환할 수 있습니다 . Ruler 5 10 15 20 25 30 5 10 15 1.3.4 기타 기능 HDR 이 모니터는 HDR 형식을 지원합니다 . HDR 콘텐츠를 감지하면 , "HDR ON" (HDR 켜기 ) 메시지가 팝업되어 정보 페이지에 표시됩니다 . PIP/PBP 모드가 켜진 경우 HDR 콘텐츠가 지원되지 않습니다 .
2.1 암 / 받침대 부착 모니터 받침을 조립하려면: 1. 상자에서 모니터를 조심스럽게 꺼냅니다 . 실수로 손상되는 것을 방지하기 위해 들어 올릴 때는 모니터를 단단히 잡는 한편 패널 화면을 누르지 마십시오 . 2. 모니터 전면을 아래로 향하게 하여 테이블 위에 올려놓습니다 ( 그림 2). 3. 암의 탭이 모니터 뒷면의 홈에 꽉 맞게 끼워지도록 모니터의 뒷면에 스탠드를 부착합니다 . ( 그림 3). 2 1 (그림 1) (그림 2) (그림 3) 모니터가 손상되지 않도록 테이블 표면을 부드러운 천으로 덮을 것을 권장합니다 . 2.2 암 / 받침대 분리 (VESA 벽걸이 ) 이 모니터의 분리 가능한 암/받침대는 VESA 벽걸이용으로 특별히 설계되었습니다. 암/받침대 분리하기: 1. 모니터의 전면이 테이블을 향하도록 엎어 놓습니다 . 2. 분리 버튼을 누른 다음 , 암 / 베이스를 모니터에서 분리합니다 ( 그림 1).
2.3 • VESA 벽걸이 키트 (100 x 100 mm) 는 별도로 구입해야 합니다 . • 최소 중량 / 부하 22.7kg 인 UL 인증 벽걸이용 브래킷만 사용하십시오 ( 나사 크기 : M4 x 10 mm). 모니터 조정 • 최적의 보기를 위해서는 모니터의 전체 면을 바라보면서 자신에게 가장 편안하 게 느껴지는 각도로 모니터를 조정할 것을 권장합니다. • 각도를 변경할 때는 모니터가 떨어지지 않도록 받침대를 잡으십시오. • 모니터 각도를 +23˚ ~ -5˚의 범위에서 조정할 수 있고, 왼쪽에서 오른쪽으로 60˚ 회전할 수 있습니다. 또한 모니터 높이를 +/- 120 mm 내에서 조정할 수 있습 니다.
모니터 피보팅 1. 가장 높은 위치까지 모니터를 들어올립니다 . 2. 최대 각도로 모니터를 기울입니다 . 3. 모니터를 원하는 각도로 피벗합니다. +23° ~ -5° 90° 90° 보기 각도를 조정하는 동안 모니터가 약간 흔들리는 것은 정상입니다. 4. 모니터가 회전하면 , OSD 메뉴 항목도 자동으로 회전합니다 .
2.4 1. 케이블 연결 다음 지침에 따라 케이블을 연결합니다 : 정비 전용 • 전원 코드 연결하기: 전원 코드의 한쪽 끝을 모니터의 AC 입력 포트에 연결하고 반대쪽 끝을 전원 콘센트에 연결합니다. • HDMI/DisplayPort/USB 타입 C* 케이블을 연결하는 방법: a. HDMI/DisplayPort/USB 타입 C* 케이블의 한쪽 끝을 모니터의 HDMI/ DisplayPort/USB 타입 C 잭에 연결합니다. b. HDMI/DisplayPort/USB 타입 C* 케이블의 다른쪽 끝을 장치의 HDMI/ DisplayPort/USB 타입 C 잭에 연결합니다. USB 인증 타입 C 케이블을 사용할 것을 권장합니다. 신호 소스가 DP Alt 모드를 지원하면 모든 비디오, 오디오 및 데이터 신호를 전송할 수 있습니다. • 이어폰 사용하기: HDMI/DisplayPort/USB 타입 C 신호가 들어올 때 플러그형 끝 을 모니터의 이어폰 잭에 연결합니다.
2. 케이블 정리하기 : 아래 순서에 따라 스탠드의 케이블 관리 슬롯을 통해 케이블을 연결하는 것이 좋습니다 . 1 3. 3 3 2 5 5 4 4 4 4 6 필요한 경우 입력 / 출력 포트 덮개를 부착합니다 . 2.5 모니터 켜기 전원 단추 를 누릅니다. 전원 단추의 위치는 페이지 1-2를 참조하십시오. 전원 표시기 가 흰색으로 켜져서 모니터가 켜졌음을 나타냅니다.
2-6 2 장 : 설치
3.1 OSD ( 온스크린 디스플레이 ) 메뉴 3.1.1 재구성 방법 ProArt Preset ASUS PA27UCX 표준 모드 DisplayPort 3840 x 2160@ 60Hz 표준 모드 sRGB 모드 Adobe RGB 모드 Rec 2020 모드 DCI-P3 모드 DICOM 모드 Rec 709 모드 1. 메뉴 (5- 방향 ) 버튼을 눌러 OSD 메뉴를 활성화합니다. 2. 메뉴 (5- 방향 ) 버튼을 위 / 아래 / 왼쪽 / 오른쪽으로 이동하여 기능을 탐색 합니다 . 원하는 기능을 강조표시하고 메뉴 (5- 방향 ) 버튼을 눌러 활성화 합니다 . 선택한 기능에 하위 메뉴가 있으면 메뉴 (5- 방향 ) 버튼을 다시 위 / 아래로 이동하여 하위 메뉴 기능을 탐색합니다 . 원하는 하위 메뉴 기능을 강조표시하고 메뉴 (5- 방향 ) 버튼을 누르거나 메뉴 (5- 방향 ) 버튼을 이동하여 활성화합니다 . 3.
3.1.2 1. OSD 기능 개요 ProArt Preset 이 기능은 선호에 따라 선택할 수 있는 13개의 하위 기능을 포함합니다. 각 모 드에 있는 리셋 선택을 통해 설정을 유지하거나 사전 설정 모드로 되돌릴 수 있습니다. ProArt Preset ASUS PA27UCX 표준 모드 DisplayPort 3840 x 2160@ 60Hz 표준 모드 sRGB 모드 Adobe RGB 모드 Rec 2020 모드 DCI-P3 모드 DICOM 모드 Rec 709 모드 • 표준 모드: 문서 편집을 위해 선택할 수 있는 최상의 제품입니다. • sRGB 모드: sRGB 색 공간과 sRGB 모드는 문서 편집 시 선택할 수 있는 최상의 모드입니다. • Adobe RGB 모드: Adobe RGB 색 공간과 호환됩니다. • Rec. 2020 모드: Rec. 2020 색 공간과 호환됩니다. • DCI-P3 모드: DCI-P3 색 공간과 호환됩니다.
• HDR_HLG: * • HLG BT2100: BT2100을 따릅니다. HDR_DolbyVision: • * 밝음: DolbyVision 밝음 모드 설정을 따릅니다. * 어두움: DolbyVision 어두움 모드 설정을 따릅니다. 사용자 모드 1 / 사용자 모드 2: 고급 설정에서 색을 조정할 수 있게 합니다. 또한, ProArt 보정을 수행한 후 하나 또는 두 개의 ProArt 보정 프로파일을 사용자 모드 1/사용자 모드 2로 저장한 다음 여기에서 빠르게 액세스할 수 있습니다. ProArt 색 보정을 수행하는 동안 다음 설정을 적용하십시오. • 출력 동적을 전체 범위로 설정하십시오 . • 출력 색 형식을 RGB 로 설정하십시오 . • 출력 색 농도를 8 비트로 설정하십시오 . 아래 표에서는 각 ProArt 사전 설정 모드의 기본 구성을 보여줍니다 .
기능 DICOM 색 온도 고정 (6,500K) 밝기 50 대비 80 선명도 사용 (0) 중간 (50) 중간 (50) 사용 ( 기본 ) 사용 ( 기본 ) 사용 ( 자동 ) 사용 (2.2) 사용 ( 꺼짐 ) 사용 (0) 채도 색조 고급 설정 검정 레벨 입력 범위 감마 균일도 보정 VividPixel 2.
• 레벨 1~4: 레벨이 높을수록 블루 라이트가 흩어집니다. 블루 라이트 필터 가 활성화되면 표준 모드의 기본 설정을 자동으로 가져옵니다. 레벨 1에서 레벨 3 사이에서 밝기 기능을 사용자가 구성할 수 있습니다. 레벨 4는 최적 화된 설정입니다. 이는 TUV 로우 블루 라이트 인증을 준수합니다. 밝기 기 능은 사용자가 구성할 수 없습니다. 눈의 피로를 줄이기 위해 다음 사항을 참조하십시오. 3. • 오랜 시간 작업할 때는 사용자가 잠시 동안 디스플레이를 멀리하고 눈을 쉬 어야 합니다 . 1 시간 가량 컴퓨터 작업을 계속한 후에는 잠시 ( 약 5 분 ) 휴 식을 취하는 것이 좋습니다 . 짧게 자주 쉬는 것이 한 번에 오래 쉬는 것보다 더 효과적입니다 . • 눈의 피로를 덜고 건조함을 최소화하려면 , 정기적으로 먼 곳의 사물을 쳐다 보면서 눈을 쉬게 해야 합니다 . • 눈 운동은 눈의 피로를 완화하는 데 도움이 됩니다 . 눈 운동을 자주 하십시 오 .
• 색조: 이미지 색을 녹색과 자주색 간에 이동시킵니다. • 색조절: 9300K, 6500K, 5500K, 5000K 및 P3-영화관을 포함한 5개의 모드 가 포함되어 있습니다. P3- 영화관은 DCI-P3 모드를 선택한 경우에만 사용할 수 있습니다 . • 감마: 색 모드를 2.6, 2.4, 2.2, 2.0 또는 1.8로 설정할 수 있습니다. • 검정 레벨: 디스플레이의 가장 어두운 레벨. • • 4. * 신호: 가장 어두운 회색 레벨에서 초기화된 첫 번째 신호 레벨을 조 정합니다. * 백라이트: 백라이트의 어둡기를 조정합니다. * 6축 색조 조정. * 6축 채도 조정. * R, G, B에 대한 게인 레벨을 조정합니다. 색: * R, G, B에 대한 검은색 레벨 오프셋 값을 조정합니다. 색상 재설정: * 현재 모드 색상 재설정: 현재 색 모드의 색상 설정을 공장 기본값으로 재설정합니다.
• • 이 기능을 활성화하려면 다음을 수행해야 합니다 . 즉 , PBP 를 끄십시오 . • 입력 소스가 4:3 형식일 때만 4:3 을 사용할 수 있습니다 . HDMI 입력 소스에 서만 OverScan 을 사용할 수 있습니다 . 균일성 보상: 화면의 다른 영역을 조정하여 화면 균일성 오류를 줄임으로써 화면 전체에 걸쳐 일관성 있는 밝기와 색을 제공합니다. 이 기능을 활성화하려면 다음을 수행해야 합니다 . 즉 , 장치에서 동적 디밍을 끄고 HDR 을 비활성화하십시오 . • VividPixel: 표시된 영상의 윤곽을 개선하여 화면에 고화질 이미지를 생성 합니다. 이 기능을 활성화하려면 다음을 수행해야 합니다 . 장치에서 명도를 활성화하고 HDR 을 비활성화합니다 . • 입력 범위: 전체가 검은색인 신호 범위를 흰색으로 표시된 디스플레이 범위 에 매핑합니다. • 모션 싱크: 디스플레이를 높은 화면 주사율 성능으로 시뮬레이트하영 다른 백라이트 주파수를 생성합니다.
6. PIP/PBP 설정 PIP/PBP 설정에서는 원래의 비디오 소스의 주 창 외에 다른 비디오 소스로부 터 연결된 다른 하위 창을 열 수 있습니다. 이 기능을 활성화함으로써, 모니터 는 서로 다른 소스로부터 최대 2개의 이미지를 표시할 수 있습니다. 이 기능을 활성화하려면 다음을 수행해야 합니다 . 즉 , 장치에서 동적 디밍과 Adaptive-Sync 를 끄고 HDR 을 비활성화하십시오 . ASUS PA27UCX 표준 모드 DisplayPort 3840 x 2160@ 60Hz PIP/PBP 설정 PIP/PBP 모드 PIP/PBP 소스 색 설정 PIP 크기 • PIP/PBP 모드: PIP, PBP, PBP x 3 또는 PBP x 4 기능을 선택하거나 이를 끕니다. • PIP/PBP 소스: HDMI-1, HDMI-2, DisplayPort 및 USB 타입 C 중에서 비디 오 입력 소스를 선택합니다. 아래 표에서는 입력 소스의 조합을 보여줍니 다.
7. 입력 선택 이 기능에서는 원하는 입력 소스를 선택할 수 있습니다. 입력 선택 ASUS PA27UCX 표준 모드 DisplayPort 3840 x 2160@ 60Hz HDMI-1 HDMI-2 DisplayPort Type C 8. 시스템 설정 시스템을 조정할 수 있습니다. 시스템 설정 ASUS PA27UCX 표준 모드 DisplayPort 3840 x 2160@ 60Hz HDR 미리보기 Adaptive-Sync 동적 디밍 절전 OSD 설정 언어 보정 미리 알림 • HDR 미리보기: HDR10 및 HLG 매핑으로 비-HDR 콘텐츠 성능을 미리 볼 수 있습니다. HDR 미리보기 기능이 켜져 있는 동안 HDR_PQ DCI, HDR_ PQ Rec2020 및 HDR_HLG를 선택할 수 있습니다.
이 기능을 활성화하려면 다음을 수행해야 합니다 . 즉 , PIP/PBP 를 끄십시오 . • • • USB 설정: USB 타입 C 포트 설정을 구성합니다. USB 설정 매개변수는 소 스가 USB 타입 C 포트에 연결된 경우에만 출력 해상도에 영향을 미칩니 다. USB 2.0과 USB 3.0의 기술적 차이로 인해 최대 USB 데이터 처리량(대 역폭 및 기타 관련 특성)이 달라지며, 그 결과 달라진 처리량이 최대 출력 해상도에 영향을 미칩니다. * USB 3.0: USB 타입 C 포트의 3.0 사양에 따른 데이터 전송 속도는 4K2K 30Hz의 최대 해상도만 출력할 수 있습니다. * USB 2.0: USB 타입 C 포트의 2.0 사양에 따른 데이터 전송 속도는 4K2K 60Hz의 최대 해상도를 출력할 수 있습니다. • USB 타입 C 와 타입 A 연결 케이블을 사용할 경우 데이터 전송 속도가 USB 3.0 레벨로 유지됩니다 .
• DisplayPort 스트림: 그래픽 카드와의 호환성. 그래픽 카드 DP 버전에 맞 게 DisplayPort 1.1 또는 DisplayPort 1.2를 선택합니다. Adaptive-Sync 가 꺼진 경우에만 DisplayPort 1.1 을 사용할 수 있습니다 . • 키 잠금: 모든 기능 키를 비활성화합니다. 상단에서 두 번째 버튼을 5초 이 상 누르면 키 잠금 기능을 취소할 수 있습니다. • 전원 표시기: 전원 LED 표시기를 켜거나 끕니다. • 주변광 효과: 디스플레이 밝기를 주변광 변화와 동기화합니다. 이 기능을 활성화하려면 다음을 수행해야 합니다 . 장치에서 HDR 을 비활성화하고 모션 싱크를 끄고 블루 라이트 필터를 레벨 0 으로 설정하십시오 . • 정보: 모니터 정보를 표시합니다. • 모든 리셋: "예"를 선택하면 초기 설정값으로 복구됩니다. 9. 바로가기 키 바로가기 키 1 및 2 버튼의 기능을 정의합니다.
3.2 사양 요약 온도(작동) TFT LCD 26.93" (16:9, 68.4 cm) 와이드 스크린 3840 x 2160 0.1553 mm 300 cd/m2(기본), 1200 cd/m2(최대) 1,000,000:1 100,000,000:1(동적 디밍이 켜진 경우) 178˚/178˚ 10억 7천만 Adobe RGB 99.5%, DCI-P3 97%, Rec2020 83%, sRGB 100% 5 ms(회색 간) 13가지 색 사전 설정 모드 5가지 색 온도 HDMI v2.0, DisplayPort v1.2a, USB 타입 C 예 업스트립 x 1, 다운스트림 x 4 검정색 흰색(켜짐)/주황색(대기) +23˚~ -5˚ +60˚~ -60˚ +90˚; -90˚ 120 mm 예 AC: 100~240 V 전원 켜짐: < 46 W** (기본), 대기: < 0.5 W (기본.), 전원 꺼짐: 0 W (스위치 꺼짐) 0˚C~40˚C 온도(비작동) -20˚C~+60˚C 치수(폭 x 높이 x 깊이) 625.
다국어 액세서리 적합성 및 표준 21개 언어(영어, 프랑스어, 독일어, 이탈리아어, 스페인 어, 네덜란드어, 포르투갈어, 러시아어, 체코어, 크로아 티아어, 폴란드어, 루마니아어, 헝가리어, 터키어, 중국 어 간체, 중국어 번체, 일본어, 한국어, 태국어, 인도네 시아어, 페르시아어) 빠른 시작 안내서, 보증서, 전원 코드, HDMI 케이블, USB 타입 C 케이블, DisplayPort 케이블, USB 타입 C 와 타입 A 연결 케이블, 입력/출력 포트 커버, 색 보정 테스트 보고서, 색 보정기(PA27UCX-K용), 후드 UL/cUL, FCC, ICES-3, CB, CE, ErP, WEEE, ISO 9241-307, UkrSEPRO, CU, CCC, CEL, BSMI, RCM, MEPS, VCCI, PSE, PC Recycle, J-MOSS, KC, KCC, e-Standby, PSB, RoHS, CEC, Windows 7, 8.
23 5 298,08 [11.7] 55 [2.2] 157,93 [6.2] 14,52 [.6] 60 91,27 [3.6] 48,9 [1.9] 198,09 [7.8] 60 544,5 [21.4] 625,2 [24.6] AA-Center 90 424,5 [16.7] 7,86 [.3] 120 [4.72] 14,38 [.6] 601,6 [23.7] 596,16 [23.5] 324 [12.8] 16,08 [.6] Pivot: +/- 90 degree Tilt: -5~23 degree Swivel: +/- 60 degree Lift: 120mm 90 162,97 [6.4] 228,8 [9.0] 42 [1.7] 100 [3.9] 26 [1.0] 24 [.9] 100 [3.9] 21,55 [.8] 33,45 [1.3] 24,95 [1.0] 24 [1] 23 [1] 12 [.5] 19 [.7] 11,99 [.5] 12,01 [.
3.4 문제 해결 (FAQ) 문제 전원 LED가 켜지지 않습니다 가능한 해결책 • • • 전원 LED가 주황색으로 빛나고 화면에 이 • 미지가 없습니다 • • • 화면 이미지가 너무 밝거나 어둡습니다 • 화면 이미지가 흔들리거나 이미지에 물결 • 무늬가 표시됩니다 • 화면 이미지에 색 결함이 있습니다(흰색 이 하얗게 보이지 않음) • • • 소리가 나지 않거나 약합니다. • • • ASUS PA27UCX 시리즈 LCD 모니터 단추를 눌러 모니터가 켜짐 모드에 있는 지 확인합니다. 전원 코드가 모니터와 전원 콘센트에 제대로 연결되어 있는지 확인합니다. 전원 스위치가 켜졌는지 확인합니다. 모니터와 컴퓨터가 켜짐 모드에 있는지 확 인합니다. 신호 케이블이 모니터와 컴퓨터에 제대로 연 결되어 있는지 확인합니다. 신호 케이블을 검사하여 구부러진 핀이 없는 지 확인합니다. 사용 가능한 다른 모니터를 컴퓨터에 연결하 여 컴퓨터가 제대로 작동하는지 알아봅니다.
3.5 지원되는 작동 모드 해상도 주파수 수직 주파수(Hz) 수평 주파수(KHz) 픽셀(MHz) 640 x 480 640 x 480 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 800 x 600 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1280 x 720 1280 x 960 1280 x 1024 1280 x 1024 59.94(N) 72.82(N) 75.00(N) 70.08(P) 56.25(P) 60.32(P) 72.12(P) 75.00(P) 60.00(N) 70.069(N) 75.00(N) 75.00(P/N) 60 60.00(N) 60.02(P) 75.02(P) 31.47(N) 37.87(N) 37.5(N) 31.47(N) 35.16(P) 37.88(P) 48.08(P) 46.86(P) 48.36(N) 56.476(N) 60.02(N) 67.5(P/N) 44.77(N) 60.00(P) 63.98(P) 79.
해상도 1920 × 1080p 1920 × 1080i 1440 x 480P 1440 x 576P 1280 × 720p 수직 주파수(Hz) 수평 주파수(KHz) 50 56.25 59.94 67.43 60 67.5 50 28.13 59.94 33.72 60 33.75 59.94 31.47 60 31.5 50 31.25 50 37.5 59.94 44.95 60 45 * 표에 포함되지 않은 모드는 지원되지 않을 수 있습니다 . 최적의 해상도를 위해 위의 표에 포함된 모드를 선택할 것을 권장합니다 .
3-18 3 장 : OSD ( 온스크린 디스플레이 ) 메뉴