PT201 Series LCD Monitor Setup Manual
E9529 June 2014 First Edition Information on the Disposal of this Equipment Do not throw your this product in municipal waste. This product has been designed to enable proper reuse of parts and recycling. The symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment and mercury-containing button cell battery) should not be placed in municipal waste. Check local regulations for disposal of electronic products.
Contents IMPORTANT INFORMATION.....................................................................................................................................3 DEAR ASUS CUSTOMER.........................................................................................................................................3 SAFETY PRECAUTIONS...........................................................................................................................................4 SAFETY INSTRUCTIONS............
SAFETY PRECAUTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product.
SAFETY INSTRUCTIONS - Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam. Do not use in an environment where there are corrosive gases (sulfur dioxide, hydrogen sulfide, nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this could lead to fire. - Ensure that the monitor does not come into contact with water or other fluids.
Connecting Devices Caution TIPS • Be sure to turn off the power and disconnect the plug from the power outlet before connecting/disconnecting cables. Also, read the manual of the equipment to be connected. • Do not forcibly bend or apply force to cables. Doing so may result in wire breakage or other damage. • When connecting cables, spread a soft cloth on a stable level surface such as a desk, and gently place the monitor on it with the screen facing down.
Binding Cables Caution • When connecting cables, spread a soft cloth on a stable level surface such as a desk, and gently place the monitor on it with the screen facing down. Video cable and USB cable Secure the video cable (HDMI or DisplayPort) and USB cable using the cable clamp. 1. Remove the cable clamp. 2. Route the cables through the cable 3. Push the cable clamp down into restraint slot. place.
Connecting the Monitor to a Power Source Caution • Use only the AC adapter and power cord supplied with the monitor. 1. Connect the monitor to the power outlet using the supplied AC adapter and power cord. Back of monitor For power outlet AC adapter connection terminal Core restrainer AC adapter core 2. Push the AC adapter core into the core restrainer.
Installation Installing on a stand (Standing position) Placement on the variable stand 3. Place the monitor in the standing position, and adjust the angle of the stand. Hold the top of the display with one hand so that it does not fall over, hold the rear leg of the stand with your other hand, and adjust the angle of the stand. Place the unit on the supplied variable stand. Caution • The variable stand is designed for placement of the unit in the landscape orientation.
Installation Installing on a table (Pen writing position/Horizontal position) Remove the monitor from the stand and place face-down on a table or other level surface. Horizontal position Place the monitor on a table or other level surface. Caution • When using the monitor horizontally, use the horizontal tab in the upright position. 1. Lift up the two tabs on the back of the monitor. Caution • Do not exert a large amount of force on the monitor from above. Doing so may damage the flap.
Turning Power On/Off Turning on the power Turning off the power 1. Press the POWER button. 1. Turn off the PC. 2. Depress the POWER button for around 2 seconds. POWER button POWER button Press Power LED The power LED turns on. The power LED turns off. Caution 2. Turn on the PC. The screen appears.
Specifications nProduct Specifications Model PT201 LCD component 19.5” (49.3 cm diagonal)TFT LCD Max. resolution (pixels) 1920 x 1080 Max. colors Approx. 16.77 million colors Pixel pitch 0.225mm (H) x 0.225 mm (V) Viewing angle 178° right/left/up/down (contrast ratio ≥ 10) Screen display size (mm) 432 x 243 Input terminals HDMI x1 DisplayPort x1 Other terminals USB USB Type A Ver.2.