User's Manual
Table Of Contents
- À propos de ce manuel
- Informations sur la sécurité
- Notes
- Résumé des spécifications de la Rampage III Black Edition
- Chapitre 1: Introduction
- au produit
- Chapitre 2 : Informationssur le matériel
- 2.1 Avant de commencer
- 2.2 Vue générale de la carte mère
- 2.3 Monter votre ordinateur
- 2.3.1 Outils et composants additionnels pour monter un ordinateur de bureau
- 2.3.2 Installation du CPU
- 2.3.3 Installation du ventilateur/dissipateur de CPU
- 2.3.4 Installation d’un module mémoire
- 2.3.5 Installation de la carte mère
- 2.3.6 Connexion des prises d'alimentation ATX
- 2.3.7 Connexion de périphériques SATA
- 2.3.8 Connecteur d'E/S frontal
- 2.3.9 Installation d'une carte d'extension
- 2.3.10 ThunderBolt
- 2.3.11 Connecteurs arrières
- 2.3.11 Connexions audio
- 2.4 Démarrer pour la première fois
- 2.5 Éteindre l’ordinateur
- Chapitre 3 : Le BIOS
- 3.1 Gérer et mettre à jour votre BIOS
- 3.2 Configuration du BIOS
- 3.3 Menu Extreme Tweaker
- 3.3.1 GPU.DIMM Post
- 3.3.1 CPU Level Up [Auto]
- 3.3.3 Ai Overclock Tuner [Auto]
- 3.3.4 CPU Ratio Setting [Auto]
- 3.3.5 CPU Turbo Power Limit [Disabled]
- 3.3.6 CPU Configuration
- 3.3.7 BCLK Frequency [XXX]
- 3.3.8 BCLK Enhance [Auto]
- 3.3.9 PCIE Frequency [XXX]
- 3.3.10 DRAM Frequency [Auto]
- 3.3.11 UCLK Frequency [Auto]
- 3.3.12 QPI Link Data Rate [Auto]
- 3.3.13 Memory Recheck [Disabled]
- 3.3.14 Memory Configuration Protect [Disabled]
- 3.3.15 DRAM Timing Control
- 3.3.16 CPU QPI Strength [Auto]
- 3.3.17 ALT QPI Strength [Auto]
- 3.3.18 First 2 Slots PCIE Strength [Auto]
- 3.3.19 Last 2 Slots PCIE Strength [Auto]
- 3.3.20 CPU Differential Amplitude [Auto]
- 3.3.21 CPU Clock Skew [Auto]
- 3.3.22 IOH Clock Skew [Auto]
- 3.3.23 Digi+ VRM Duty Control [T.Probe]
- 3.3.24 PWM Volt. Control [Auto]
- 3.3.25 Load-Line Calibration [Auto]
- 3.3.26 CPU Voltage OCP [Enabled]
- 3.3.27 CPU PWM Frequency [Auto]
- 3.3.28 Phase Control [Extreme]
- 3.3.29 Extreme OV [Disabled]
- 3.3.30 Extreme OC [Auto]
- 3.3.31 CPU Voltage [Auto]
- 3.3.32 CPU PLL Voltage [Auto]
- 3.3.33 QPI/DRAM Core Voltage [Auto]
- 3.3.34 DRAM Bus Voltage [Auto]
- 3.3.35 DRAM REF Voltages
- 3.3.36 IOH Voltage [Auto]
- 3.3.37 IOH PCIE Voltage [Auto]
- 3.3.38 ICH Voltage [Auto]
- 3.3.39 ICH PCIE Voltage [Auto]
- 3.4 Menu Main (Principal)
- 3.5 Menu Advanced (Avancé)
- 3.6 Menu Power (Alimentation)
- 3.7 Menu Boot (Démarrage)
- 3.8 Menu Tools (Outils)
- 3.9 Menu Exit (Sortie)
- Chapitre 4 : Supportlogiciel
- Chapter 5: Support des technologies multi-GPU
10. LED de debogage
Ces voyants offrent un système d'afchage à code symbolisé par deux
valeurs numériques pour vous informer de l'état du système. Consultez le
tableau de debogage pour plus d'informations.
Tableau de debogage
Code Description
00
Not used
01
Power on. Reset type detection (soft/hard).
02
AP initialization before microcode loading
03
System Agent initialization before microcode loading
04
PCH initialization before microcode loading
05
OEM initialization before microcode loading
06
Microcode loading
07
AP initialization after microcode loading
08
System Agent initialization after microcode loading
09
PCH initialization after microcode loading
0A
OEM initialization after microcode loading
0B
Cache initialization
0C – 0D
Reserved for future AMI SEC error codes
0E
Microcode not found
0F
Microcode not loaded
10
PEI Core is started
11 – 14
Pre-memory CPU initialization is started
15 – 18
Pre-memory System Agent initialization is started
19 – 1C
Pre-memory PCH initialization is started
LED de debogage de la Rampage III Black Edition
2-26 Chapitre 2 : informations sur le matériel