User's Manual
Table Of Contents
- À propos de ce manuel
- Informations sur la sécurité
- Notes
- Résumé des spécifications de la Rampage III Black Edition
- Chapitre 1: Introduction
- au produit
- Chapitre 2 : Informationssur le matériel
- 2.1 Avant de commencer
- 2.2 Vue générale de la carte mère
- 2.3 Monter votre ordinateur
- 2.3.1 Outils et composants additionnels pour monter un ordinateur de bureau
- 2.3.2 Installation du CPU
- 2.3.3 Installation du ventilateur/dissipateur de CPU
- 2.3.4 Installation d’un module mémoire
- 2.3.5 Installation de la carte mère
- 2.3.6 Connexion des prises d'alimentation ATX
- 2.3.7 Connexion de périphériques SATA
- 2.3.8 Connecteur d'E/S frontal
- 2.3.9 Installation d'une carte d'extension
- 2.3.10 ThunderBolt
- 2.3.11 Connecteurs arrières
- 2.3.11 Connexions audio
- 2.4 Démarrer pour la première fois
- 2.5 Éteindre l’ordinateur
- Chapitre 3 : Le BIOS
- 3.1 Gérer et mettre à jour votre BIOS
- 3.2 Configuration du BIOS
- 3.3 Menu Extreme Tweaker
- 3.3.1 GPU.DIMM Post
- 3.3.1 CPU Level Up [Auto]
- 3.3.3 Ai Overclock Tuner [Auto]
- 3.3.4 CPU Ratio Setting [Auto]
- 3.3.5 CPU Turbo Power Limit [Disabled]
- 3.3.6 CPU Configuration
- 3.3.7 BCLK Frequency [XXX]
- 3.3.8 BCLK Enhance [Auto]
- 3.3.9 PCIE Frequency [XXX]
- 3.3.10 DRAM Frequency [Auto]
- 3.3.11 UCLK Frequency [Auto]
- 3.3.12 QPI Link Data Rate [Auto]
- 3.3.13 Memory Recheck [Disabled]
- 3.3.14 Memory Configuration Protect [Disabled]
- 3.3.15 DRAM Timing Control
- 3.3.16 CPU QPI Strength [Auto]
- 3.3.17 ALT QPI Strength [Auto]
- 3.3.18 First 2 Slots PCIE Strength [Auto]
- 3.3.19 Last 2 Slots PCIE Strength [Auto]
- 3.3.20 CPU Differential Amplitude [Auto]
- 3.3.21 CPU Clock Skew [Auto]
- 3.3.22 IOH Clock Skew [Auto]
- 3.3.23 Digi+ VRM Duty Control [T.Probe]
- 3.3.24 PWM Volt. Control [Auto]
- 3.3.25 Load-Line Calibration [Auto]
- 3.3.26 CPU Voltage OCP [Enabled]
- 3.3.27 CPU PWM Frequency [Auto]
- 3.3.28 Phase Control [Extreme]
- 3.3.29 Extreme OV [Disabled]
- 3.3.30 Extreme OC [Auto]
- 3.3.31 CPU Voltage [Auto]
- 3.3.32 CPU PLL Voltage [Auto]
- 3.3.33 QPI/DRAM Core Voltage [Auto]
- 3.3.34 DRAM Bus Voltage [Auto]
- 3.3.35 DRAM REF Voltages
- 3.3.36 IOH Voltage [Auto]
- 3.3.37 IOH PCIE Voltage [Auto]
- 3.3.38 ICH Voltage [Auto]
- 3.3.39 ICH PCIE Voltage [Auto]
- 3.4 Menu Main (Principal)
- 3.5 Menu Advanced (Avancé)
- 3.6 Menu Power (Alimentation)
- 3.7 Menu Boot (Démarrage)
- 3.8 Menu Tools (Outils)
- 3.9 Menu Exit (Sortie)
- Chapitre 4 : Supportlogiciel
- Chapter 5: Support des technologies multi-GPU
Tableau de debogage (suite)
Code Description
F2
Recovery process started
F3
Recovery rmware image is found
F4
Recovery rmware image is loaded
F5-F7
Reserved for future AMI progress codes
F8
Recovery PPI is not available
F9
Recovery capsule is not found
FA
Invalid recovery capsule
FB-FF
Reserved for future AMI error codes
60
DXE Core is started
61
NVRAM initialization
62
Installation of the PCH Runtime Services
63 – 67
CPU DXE initialization is started
68
PCI host bridge initialization
69
System Agent DXE initialization is started
6A
System Agent DXE SMM initialization is started
6B – 6F
System Agent DXE initialization (System Agent module specic)
70
PCH DXE initialization is started
71
PCH DXE SMM initialization is started
72
PCH devices initialization
73 – 77
PCH DXE Initialization (PCH module specic)
78
ACPI module initialization
79
CSM initialization
7A – 7F
Reserved for future AMI DXE codes
80 – 8F
OEM DXE initialization codes
90
Boot Device Selection (BDS) phase is started
91
Driver connecting is started
92
PCI Bus initialization is started
93
PCI Bus Hot Plug Controller Initialization
94
PCI Bus Enumeration
95
PCI Bus Request Resources
96
PCI Bus Assign Resources
2-28 Chapitre 2 : informations sur le matériel