User's Manual
Table Of Contents
- À propos de ce manuel
- Informations sur la sécurité
- Notes
- Résumé des spécifications de la Rampage III Black Edition
- Chapitre 1: Introduction
- au produit
- Chapitre 2 : Informationssur le matériel
- 2.1 Avant de commencer
- 2.2 Vue générale de la carte mère
- 2.3 Monter votre ordinateur
- 2.3.1 Outils et composants additionnels pour monter un ordinateur de bureau
- 2.3.2 Installation du CPU
- 2.3.3 Installation du ventilateur/dissipateur de CPU
- 2.3.4 Installation d’un module mémoire
- 2.3.5 Installation de la carte mère
- 2.3.6 Connexion des prises d'alimentation ATX
- 2.3.7 Connexion de périphériques SATA
- 2.3.8 Connecteur d'E/S frontal
- 2.3.9 Installation d'une carte d'extension
- 2.3.10 ThunderBolt
- 2.3.11 Connecteurs arrières
- 2.3.11 Connexions audio
- 2.4 Démarrer pour la première fois
- 2.5 Éteindre l’ordinateur
- Chapitre 3 : Le BIOS
- 3.1 Gérer et mettre à jour votre BIOS
- 3.2 Configuration du BIOS
- 3.3 Menu Extreme Tweaker
- 3.3.1 GPU.DIMM Post
- 3.3.1 CPU Level Up [Auto]
- 3.3.3 Ai Overclock Tuner [Auto]
- 3.3.4 CPU Ratio Setting [Auto]
- 3.3.5 CPU Turbo Power Limit [Disabled]
- 3.3.6 CPU Configuration
- 3.3.7 BCLK Frequency [XXX]
- 3.3.8 BCLK Enhance [Auto]
- 3.3.9 PCIE Frequency [XXX]
- 3.3.10 DRAM Frequency [Auto]
- 3.3.11 UCLK Frequency [Auto]
- 3.3.12 QPI Link Data Rate [Auto]
- 3.3.13 Memory Recheck [Disabled]
- 3.3.14 Memory Configuration Protect [Disabled]
- 3.3.15 DRAM Timing Control
- 3.3.16 CPU QPI Strength [Auto]
- 3.3.17 ALT QPI Strength [Auto]
- 3.3.18 First 2 Slots PCIE Strength [Auto]
- 3.3.19 Last 2 Slots PCIE Strength [Auto]
- 3.3.20 CPU Differential Amplitude [Auto]
- 3.3.21 CPU Clock Skew [Auto]
- 3.3.22 IOH Clock Skew [Auto]
- 3.3.23 Digi+ VRM Duty Control [T.Probe]
- 3.3.24 PWM Volt. Control [Auto]
- 3.3.25 Load-Line Calibration [Auto]
- 3.3.26 CPU Voltage OCP [Enabled]
- 3.3.27 CPU PWM Frequency [Auto]
- 3.3.28 Phase Control [Extreme]
- 3.3.29 Extreme OV [Disabled]
- 3.3.30 Extreme OC [Auto]
- 3.3.31 CPU Voltage [Auto]
- 3.3.32 CPU PLL Voltage [Auto]
- 3.3.33 QPI/DRAM Core Voltage [Auto]
- 3.3.34 DRAM Bus Voltage [Auto]
- 3.3.35 DRAM REF Voltages
- 3.3.36 IOH Voltage [Auto]
- 3.3.37 IOH PCIE Voltage [Auto]
- 3.3.38 ICH Voltage [Auto]
- 3.3.39 ICH PCIE Voltage [Auto]
- 3.4 Menu Main (Principal)
- 3.5 Menu Advanced (Avancé)
- 3.6 Menu Power (Alimentation)
- 3.7 Menu Boot (Démarrage)
- 3.8 Menu Tools (Outils)
- 3.9 Menu Exit (Sortie)
- Chapitre 4 : Supportlogiciel
- Chapter 5: Support des technologies multi-GPU
Tableau de debogage (suite)
* Tableau des codes ASL
Code Description
C0– CF
OEM BDS initialization codes
D0
CPU initialization error
D1
System Agent initialization error
D2
PCH initialization error
D3
Some of the Architectural Protocols are not available
D4
PCI resource allocation error. Out of Resources
D5
No Space for Legacy Option ROM
D6
No Console Output Devices are found
D7
No Console Input Devices are found
D8
Invalid password
D9
Error loading Boot Option (LoadImage returned error)
DA
Boot Option is failed (StartImage returned error)
DB
Flash update is failed
DC
Reset protocol is not available
Status Code Description
01
System is entering S1 sleep state
02
System is entering S2 sleep state
03
System is entering S3 sleep state
04
System is entering S4 sleep state
05
System is entering S5 sleep state
10
System is waking up from the S1 sleep state
20
System is waking up from the S2 sleep state
30
System is waking up from the S3 sleep state
40
System is waking up from the S4 sleep state
AC
System has transitioned into ACPI mode. Interrupt controller is in APIC mode
AA
System has transitioned into ACPI mode. Interrupt controller is in APIC mode
2-30 Chapitre 2 : informations sur le matériel