初版 2020年2月 Copyright © 2020 ASUSTeK COMPUTER INC. 無断複写、転載を禁じます。 購入者によるバックアップの場合を除き、ASUSTeK COMPUTER INC.
目次 通知 ........................................................................ iv 安全上の注意 ............................................................. v 留意点とお手入れについて ..........................................vii 回収サービス ...........................................................viii 1.1 ようこそ!....................................................... 1-1 1.2 パッケージに含まれるもの ..................................1-1 1.3 ディスプレイアーム/ベースの組み立て................ 1-2 1.4 ケーブルの接続..............................................
通知 FCC(米国連邦通信委員会)規定の適合宣言 本装置は米国連邦通信委員会 (FCC) 規定第 15 部に準拠しています。 本装 置の操作は以下の 2 つの条件を前提としています: • • 本装置は有害な電波障害を引き起こすとは限らないこと。 本装置は、誤動作を引き起こしうる電波障害を含め、いかなる電波障害 も容認しなければならないこと。 本装置は、FCC 規定第 15 部によるクラス B デジタル装置の規制に準拠する ことが試験により確認されています。 これらの規制は、住居に設置した場合の 有害な電波障害に対する適正な保護を提供することを目的としたものです。 本装置は無線周波エネルギーを生成、使用し、放射しうるため、取り扱い 説明書の記載どおりに設置、使用しない場合には、無線通信に有害な電波 障害を引き起こす可能性があります。 ただし、特定の設置方法において電波 障害が発生しないという保証はありません。 本装置の電源のオン/オフを 切り替えることにより、本装置が無線またはテレビの受信に有害な電波障害 を引き起こしていることが確認された場合は、電波障害を修正するために 次の対処方法の
カナダ通信省規制の適合宣言 本デジタル装置は、カナダ通信省の電波障害規制で規定されている、 デジタル装置からの電波ノイズ放射に関するクラス B 制限を超えません。 本クラスBデジタル装置は、カナダの ICES-003 に準拠しています。 AEEE Yönetmeliğine Uygundur インド地域の注意事項: 本製品は、 「インドの電子廃棄物(管理)規則 (2016)」 に準拠しており、規則の スケジュールⅡに記載されている免除を除き、均質材料中において 0.1 重量 % を超える濃度での鉛、水銀、六価クロム、ポリ臭化ビフェニル (PBB) およびポリ臭素化ジフェニルエーテル (PBDE) の使用、カドミウムの場合は 均質材料中に 0.
• ディスプレイの稼動には、ラベルに表示されたタイプの電源のみを ご使用ください。 ご家庭の電源タイプが不明な場合は、お買い上げ店 または地域の電力会社までお問い合わせください。 • お住まいの地域の電力標準に従って、適切な電源プラグをご使用 ください。 • OA タップや延長コードに過度の電流負荷をかけないでください。 過重 電流は感電を引き起こす恐れがあります。 • 埃、湿気、高温や低温を避けてください。 ディスプレイを水がかかる恐れ のある場所に置かないでください。 また、ディスプレイは安定した平面に 置いてください。 • 雷雨時、または長期にわたって使用しない場合は、装置の電源コードを 抜いておいてください。 これは、電力サージによる損傷からディスプレイ を守るためです。 • ディスプレイのキャビネット開口部に、異物を押し込んだり液体を こぼしたりしないでください。 • 万全の動作を保証するため、本ディスプレイは 100-240V AC と記され 正しく構成されたレセプタクルを持つ、UL リスト記載のコンピュータで のみご使用ください。 •
留意点とお手入れについて • ディスプレイを持ち上げたり移動したりする際は、あらかじめケーブルや 電源コードを抜いておくことをお勧めします。 ディスプレイを設置する 際は、正しいやり方で持ち上げてください。 ディスプレイを持ち上げたり 持ち運んだりする際は、本体の縁をつかむようにしてください。 スタンド やコードでディスプレイを持ち上げないでください。 • お手入れ方法。 ディスプレイをオフにし、電源コードを抜きます。 ディスプレイ表面を、汚れのない柔らかい布で拭きます。 頑固な汚れ には中性クリーナーで湿らせた柔らかい布をお使いください。 • アルコールやアセトン入りのクリーナーは使用しないでください。 液晶 ディスプレイ専用クリーナーをご使用ください。 クリーナーを画面に直接 吹き付けることは絶対にしないでください。クリーナー液がたれて ディスプレイ内部に入り込むと、感電を引き起こす恐れがあります。 以下の症状は、ディスプレイの正常な状態です: • 初期のご使用中に、画面にちらつきが起こることがありますが、これは 蛍光灯の性質によるものです。 電源を切り再度入れ直
本マニュアルのルール 警告: 作業をおこなう上で、怪我の発生を防ぐための注意事項です。 注意: 作業をおこなう上で、部品の損傷を防ぐための注意事項です。 重要: 作業をおこなう際に従うべき注意事項です。 注: 作業にあたってのヒントや補足情報です。 本書に記載された以外の情報を閲覧するには 追加情報や、製品およびソフトウェアのアップデートについては、以下の 情報元を参照してください。 1. ASUS 社ホームページ ASUS 社ホームページでは、世界中に向けて ASUS 社のハードウェアお よびソフトウェア製品の最新情報を提供しています。 http://www.asus.com を参照してください。 2.
1.1 ようこそ! ASUS® 液晶ディスプレイをお買い上げいただき、誠にありがとうございます。 ASUS 社の最新型ワイド画面液晶ディスプレイは、より鮮明で幅広な高発色 ディスプレイに加え、便利な機能を搭載しています。 これらの機能により、ディスプレイがお届けする便利で快適なビジュアル体験 をお楽しみいただけます。 1.
1.3 ディスプレイアーム/ ベースの組み立て • モニターアーム/ベースを組み立てる際には、モニターを EPS (Expanded Polystyrene) 梱包内に保持することをお勧めします。 1. アームのネジ穴とベースのネジを合わせます。次に、ベースをアームに 挿入します。 2. 付属のネジを締めてベースをアームに固定します。 3. モニターベースと LED 投影カバーの三角マークを合わせます。次に、 LED 投影カバーをモニターベースに取り付けます。 4.
1.4 ケーブルの接続 1.4.1 液晶ディスプレイ背面 1 4 2 5 1. コントロールボタン 2. ケーブル管理 3. Kensington ロック 4. イヤホンジャック 5. DisplayPort HDMI-1 HDMI-2 6 7 8 3 9 10 6. HDMI-1 ポート 7. HDMI-2 ポート 8. USB 3.0 タイプ B ポート 9. USB 3.0 タイプ A ポート x2 10.
1.5 ディスプレイ各部の説明 1.5.1 コントロールボタンの使用 ディスプレイ側面にあるコントロールボタンを使用して、画像設定を調整 します。 キー 1 〜 5 を押して、キー一覧ページを開きます。 1 2 3 4 5 6 1. ( • OSD メニューをオンに切り替えます。 選択した OSD メニュー項目 を実行します。 • 値を増やす/減らすか、選択を上/下/左/右に動かします。 2. • • 閉じるボタン: OSD メニューを終了します。 モニターがスタンバイモードに入っているとき、または、 「表示信号 なし」メッセージが表示されているとき、OSD メニューをオンに します。 GamePlus ボタン: 3.
GameVisual ボタン: 4. このホットキーは、GameVisual™ ビデオインテリジェンス技術に よる 8 つのビデオプリセットモード (シーンモード、レースモード、 映画モード、RTS/RPG モード、FPS モード、sRGB モード、MOBA モード、ユーザーモード) の切り替えに使用します。 • モニターがスタンバイモードに入っているとき、または、 「表示信号 なし」メッセージが表示されているとき、OSD メニューをオンに します。 • 電源ボタン: 5. ディスプレイ電源のオン/オフを切り替えるにはこのボタンを 押します。 • 6. 電源インジケータ: 電源インジケータの色は、下の表のように定義されています。 • 白 黄色 オフ 状態 オン 説明 スタンバイモード オフ 1.5.
3. ( ) ボタンを押す、または、 ( ) ボタンを右に動かして、選択した 機能を確認し、 ( ) ボタンを上/下に動かして、設定をナビゲートし ます。 ( ) ボタンを左に動かして、オフまたは終了します。 4.
1.5.
2.1 アーム/スタンドの取り外し (VESA ウォールマウント用) • モニター表面を傷つけないでください。 モニタースタンドを取り外すときは、 モニターを常に EPS 梱包内に入れてください。 当ディスプレイの取り外し可能スタンドは、VESA ウォールマウント専用に 設計されたものです。 1. 電源コードと信号ケーブルを抜きます。 モニターを上向きにして EPS 梱包に慎重に置きます。 2. モニターとアームが接触する場所のカバーを取り外します。 3. アームをモニターの背面に固定している 4 本のネジを外します。 4. モニターからスタンド (アームおよびベース) を取り外します。 • • 2-1 VESA ウォールマウントキット (100 x 100 mm) は別売りです。 ULリストに記載された、重量/荷重が 22.
2.
3.1 OSD(オンスクリーン 表示)メニュー 3.1.1 再設定の方法 DisplayPort 2560x1440@ 165Hz レースモード Aura OFF ROG Strix XG27W HDR OFF Gaming OD 画像 FreeSync Premium Pro 色 ELMB 入力選択 GamePlus Lighting Effect GameVisual MyFavorite Shadow Boost システム MOVE/ENTER 1. 2. 3.
3.1.2 OSD 機能の紹介 1.
• Shadow Boost: モニターのガンマ曲線を調整し、画像のダーク トーンを豊かにし、画面を暗くし、物体をより見つけやすくします。 利用可能なオプション: なし、 レベル 1、 レベル 2、 レベル 3、 ダイナミック調整。 2.
• ブルーライト低減: LED バックライトから放射される青色光の エネルギーレベルを低減します。 ブルーライト低減をオフにする には、レベル 0 を選択します。 • • • ブルーライト低減がアクティブになると、レーシングモードのデフォルト設定が 自動的にインポートされます。 レベル 1 〜 3 の間では、明るさ機能をユーザーが設定できます。 レベル 4 が最適な設定です。 TUV 低ブルーライト認定に準拠します。 ユーザーは明るさ機能を設定できません。 以下を参照し、眼の緊張を緩和してください。 • • • • 長時間作業している場合、 しばらくの間、ディスプレイから離れてください。 1 時間コンピュータで連続して作業したら、短い休み (5 分以上) を取ることが 推奨されます。 短い休み時間を頻繁に取ることは、長い休み時間を 1 回取る ことより効果があります。 眼の緊張と乾きを最小限に抑えるために、 ときどき遠くの物体を見つめて眼を 休めてください。 眼の運動は眼の緊張緩和に役立ちます。 次の運動を頻繁に行ってください。 眼の疲れが取れない場合、医師にご
• カラー: 目的の色温度を選択します。 利用可能なオプション: 冷たい、通常、暖かい、ユーザーモード。 ユーザーモードでは、赤、緑、青の色みのユーザー設定が可能です。0 〜 100 の 範囲で調整します。 • • ガンマ: カラーモードを 1.8、2.2 または 2.5 に設定することが できます。 • 彩度: 彩度レベルを調整します。 0〜100 の範囲で調節可能です。 4. 入力選択 入力ソースを選択します。 DisplayPort 2560x1440@ 165Hz レースモード Aura OFF ROG Strix XG27W HDR OFF Gaming HDMI-1 画像 HDMI-2 色 DisplayPort 入力選択 Lighting Effect MyFavorite システム BACK MOVE/ENTER EXIT 5.
• Aura Sync: サポートされているすべてのデバイス間で Aura RGB 光効果を同期させる Aura Sync 機能をオンまたはオフにすること ができます。 • Aura RGB: ディスプレイ背面の Aura RGB ライトパターンを設定 します。 利用可能なオプション: レインボー、カラーサイクル、スタテ ィック、ブリージング、ストロビングおよびオフ。 スタティック、ブリージング、ストロビングなどの Aura RGB パターンでは、 好みの色を設定できます。 カラーオプションには、赤 (R)、緑 (G)、青 (B)、 シアン (C)、マゼンタ (M)、黄 (Y) が含まれます。 • • 照明モーション: ベース上の赤色光強度レベルを [レベル 1] から [レベル 3] に設定します。 赤色光をオフにするには、[レベル 0] に 設定します。 6.
7.
• 電源インジケータ: 電源LEDインジケータのオン/オフを切り替え ます。 • 電源キーロック: 電源キーを無効/有効にします。 • キーのロック: 下 ( ) ボタンを 5 秒間以上押すことにより、 キーロック機能を無効または有効にします。 • メニュー設定: メニュー タイムアウト、DDC/CIおよびメニュー画面 の透明を調整します。 • 情報: ディスプレイ情報を表示します。 • すべてのリセット: すべての設定を工場出荷時のデフォルトモード に戻すには、はいを選択します。 ASUS液晶ディスプレイXG27WQシリーズ 3-8
3.2 Aura Aura とは、モニター、マザーボード、グラフィックカード、デスクトップ PC など サポートされるデバイス上のカラフルな LED を制御するソフトウェアプログ ラムです。Aura により、これらのデバイス上の RGB LED 色を調整し、さまざま な光効果を選択することができます。 LED を校正することにより、LED の色を 補正または調整することもできます。 Aura を有効化するには: 1. OSD メニューで、Aura Sync 機能をオンに切り替えます。 2. モニターの USB 3.0 アップストリームポートをコンピュータの USB ポートに接続します。 3. Aura をインストールして、コンピュータを再起動します。 4.
3.3 仕様 モデル パネルサイズ XG27WQ 27インチ対角 (有効表示領域: 596.736 (H) x 335.664 (V) mm) 最大解像度 2560 (H) x 1440 (V) 明るさ(標準) 400cd/m2 コントラスト比(標準) 3000:1 視角(CR≤10) 178° (H) /178° (V) ディスプレイカラー 1670万色 4 ミリ秒 (GTG)、1 ミリ秒 (MPRT) 応答速度 端子 入力: HDMI x 2、DP x 1、USB 3.0 (ダウンストリーム) x 2、 USB 3.0 (アップストリーム) x 1 オーディオ入力: N/A オーディオ出力: 電源オン時消費電力 はい < 24W (オーディオ/USB/カードリーダーが接続されて おらず、画面輝度200ニットの状態で測定しました) 待機時消費電力 < 0.5W (AC110V〜AC220V) 電源オフ消費電力 < 0.5W (AC110V〜AC220V) 外形寸法(ベースを含む) (高さx幅x奥行) 梱包サイズ (幅×高さ×奥行) 523.
モデル XG27WQ 付属品 アダプタ、電源コード、クイックスタートガイド、 保証書、HDMI ケーブル (オプション)、DP ケーブル (オプション)、USB ケーブル (オプション)、LED 投影 カバーおよび可変フィルム (オプション)、入力/ 出力ポートカバー コンプライアンスおよび規格 CCC、China Energy Label、UL/C-UL、CB、BSMI、 CU(EAC)、MSIP(KCC)、VCCI、FCC、CE RCM、 E-Standby、GEMS、KC(EK)、TUV Low Blue Light/ Flicker-Free、RoHS、WEEE、EuP (Energy Saving のみ)、Ukr SEPRO、J-MOSS、Windows 7/8.
3.
3.5 対応タイミング一覧 PCでサポートされるプライマリタイミング 3-13 タイミング一覧 HDMI2.0 Display Port 1.
ビデオタイミング タイミング一覧 HDMI2.0 Display Port 1.2 720x480P@59.94Hz V V 720x480P@60Hz V V 720x576P@50Hz V V 1280x720p@50Hz V V 1280x720P@59.94Hz V V 1280x720P@60Hz V V 1920x1080P@59.