XG32UQ 超快游戏显示器
目录 声明 ......................................................................................................................... iii 安全信息....................................................................................................................... iv 保养和清洁................................................................................................................... ix 1.1 欢迎使用...................................................................................................... 1-1 1.2 物品清单.
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求。其操作符合以下两项条件: • 此设备不会产生有害干扰。 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作的干 扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规定。 这些限制旨在为居民区安装提供防止有害干扰的合理保护。本设备会产生、 使用并且辐射无线电波,如果不按照说明进行安装和使用,可能会对无线电 通讯产生有害干扰。但是,不能保证在特定安装条件下不会出现干扰。如果 本设备对无线电或电视接收造成了有害干扰(可通过关闭和打开设备电源来 确定),建议用户采取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电/电视技术人员咨询以获得帮助。 为确保符合 FCC 规定,需使用屏蔽线连接显示器和图形卡。若未 经符合性责任方的明确准许而变更或改动此设备,可能会使用户失 去操作此设备的资格。 符合性声明 此设备符合在电磁兼容 (2014/30/EU)、低电压指令
加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例中规定的数字设备无线电噪 声发射 B 级限制。 此 B 级数字设备符合加拿大 ICES-003 的要求。 此 B 级数字设备符合“加拿大干扰源设备规定”的所有要求。 Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouiller du Canada.
• 切勿将任何异物塞入或使任何液体溅入显示器机壳上的开口内。 • 为确保正常运行,本显示器只应与 UL 列出的计算机一起使用,这些计 算机的插座经过正确配置并且标记有 100 ~ 240V AC。 • 插座应安装在设备附近,并应方便使用。 • 如果在使用此显示器时遇到技术问题,请与专业服务人员联系。 • 将电源插头连接至电源之前,需提供接地连接。断开接地连接时,请务 必先将电源插头从电源处拔下,然后再断开连接。 • 请使用Delta适配器的ADP-150CH B。 • 请确认在建筑物中安装时配电系统应提供额定值为120/240V、20A(最 大)的断路器。 • 如果电源线提供3插片的插头,请将电源线插入接地的3孔插座。请勿禁 用电源线的接地插片,例如,连接2插片适配器。接地插片是重要的安 全措施。 警告 由于声压过高,使用其他听筒或耳机可能导致听力受损。 稳定性危害。 此产品一旦掉落,可能导致严重的人身伤害甚至死亡。为避免伤害,此产品 必须依照安装说明牢固地安装到地板 / 墙壁上。 产品一旦掉落,可能导致严重的人身伤害甚至死亡。为了避免许多伤害(特 别是对孩童的伤害),可以采取
切勿将此产品放在不稳定的地方。 切勿将此产品放置在高大的家具上(例如,橱柜或书柜),除非家具和产品 都固定在合适的支架上。 切勿在此产品和支撑家具之间放置布或其他物品, 切勿将玩具和遥控器等可能吸引儿童攀爬的物品放在此产品顶部或支撑此产 品的家具上。 如要现有产品需要保留而重新放置,上述注意事项同样适用。 限制有害物质声明(印度) 此产品符合“印度电子废弃物(管理)条例,2016”的要求,在匀质材料 中铅、汞、六价铬、多溴联苯 (PBBs) 和多溴二苯醚 (PBDEs) 的含量不应该 超过 0.1%,镉的含量不应该超过 0.01%,该条例附表 2 所列的豁免除外。 回收服务 ASUS 循环利用和回收计划源自我们对以最高标准实现环境保护的承诺。我 们主张为客户提供能够可靠地循环利用产品、电池和其他组件及包装材料的 解决方案。 请访问 https://csr.asus.com/english/Takeback.
欧盟家庭用户废旧设备的处置 产品或其包装物上的此符号表示本产品不得与其他家庭垃圾 一起进行废弃处理。您有责任将您的废弃设备送到专门的回收 点进行废弃电气和电子设备的回收处理。在废弃时将您的废弃 设备进行单独回收有助于节约自然资源,并确保以保护人身健 康和环保的方式进行回收处理。有关废弃设备回收处理机构的 详细信息,请联系当地市政机构、家庭垃圾处置机构、或本产 品的销售店。 与欧盟能源标签相关的产品信息 vii
防止倾倒 使用显示器时,为防止显示器掉落,应使用可以支撑显示器重量的绳索或链 条将LCD固定在墙上。 1 M4或M6螺丝 绳索 2 绳索或链条 viii • 显示器设计可能与图示有所不同。 • 安装必须由专业技术人员完成,请联系您的供应商以获取更多信 息。 • 对于净重>=7kg的型号。请选择合适方法以防止倾倒。 • 对于带有VESA安装架的型号,请使用方法 ,将带环的螺丝安装 到VESA安装架孔中,然后将绳索或链条固定在墙上。否则,请 使用方法 将绳索或链条固定在支架上,然后将其固定在墙上。
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线。采用正确的 提起方式放置显示器。提起或搬运显示器时,抓住显示器的边缘。不要 通过底座或线缆提起显示屏。 • 清洁。关闭显示器电源并拔掉电源线。使用不含麻且非研磨性的布清洁 显示器表面。将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 不要使用包含酒精或丙酮的清洁剂。使用液晶专用清洁剂。切勿直接将 清洁剂喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 打叉的带轮垃圾桶符号表示产品(电子、电气设备和含汞钮扣电池) 不得当作普通生活垃圾处理。请了解当地有关电子产品废弃处理的 有关规定。 AEEE yönetmeliğine uygundur 以下现象对于显示器来说是正常现象: • 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁。关闭电源开关, 然后重新打开,确认闪烁已消失。 • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的桌面图案有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像。 屏幕会慢慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 x 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息,网址是 https://www.asus.com 2. 可选文档 您的经销商可能在您的产品包装中添加了可选文档。这些文档不是标 准产品包装的组成部分。 3. 关于闪烁: https://www.asus.
1.1 欢迎使用 感谢您购买 ASUS® 液晶显示器! 这是 ASUS 最新推出的宽屏液晶显示器,它不但提供更艳丽、更宽、更亮 的显示屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,此显示器可为您提供方便愉快的视觉体验! 1.2 物品清单 检查包装中是否包括下列物品: 液晶显示器 显示器底座 快速入门指南 保修卡 1 条电源线 1 条 HDMI 2.1 线 1 条 DP 线 1 个电源适配器 1 条 USB 3.
1.3 组装显示器 组装显示器: • 在安装显示器支撑臂/底座时,我们建议您将显示器放在其 EPS(发泡聚苯乙烯)包装内进行。 1-2 1. 轻轻地将颈部连接到VESA安装区域。使用螺丝刀拧紧组装螺丝,并将 颈部牢固地固定在显示器上。 2. 对准VESA安装区域的VESA盖以牢固锁定。 3. 将支撑臂上的螺丝孔对准底座上附带的螺丝。然后,将底座插入支撑 臂。 4. 拧紧附带的螺丝,将底座固定到支撑臂上。 5.
1.4 连接线缆 1.4.1 液晶显示器后部 9 DCIN 1 2 1. 直流输入端口 2. USB3.2上行端口 3. USB3.2下行端口 4. USB3.2下行端口 5. HDMI2.1端口 6. HDMI2.1端口 7. DisplayPort 8. 耳机插孔 9.
1.5 显示器简介 1.5.1 使用控制按钮 使用显示器背面的控制按钮调整显示器设置。 6 6 5 5 4 4 3 3 2 2 1 1. 电源指示灯: • 2. 状态 说明 白色 开启 黄色 待机模式 关闭 关闭 电源键: • 按此按钮打开/关闭显示器的电源。显示器关闭时,按此按钮开启 显示器。 • 利用此热键,可以切换采用GameVisual™视频智能技术的八种 视频预设模式(风景模式、比赛模式、影院模式、RTS/RPG模 式、FPS模式、sRGB模式、MOBA模式和用户模式)。 • GamePlus:GamePlus功能提供一个工具包,可使用户在玩不同 类型的游戏时建立更好的游戏环境。特别是,十字瞄准线功能专为 喜欢第一人称射击(FPS)类游戏的新游戏玩家或初玩者而设计。 激活GamePlus: 3. GameVisual: 4. 1-4 下表介绍电源指示灯的颜色定义。 GamePlus: • 按GamePlus按钮进入GamePlus主菜单。 • 激活十字瞄准线、定时器、FPS计数器、狙击手、秒表或显示 对齐等功能.
• 向上/向下移动 功能。按 按钮进行选择,然后按 确认所需的 离开和退出。 • 十字瞄准线/定时器/FPS计数器/秒表可以通过按 移动。 • 为了激活狙击手,您需要在设备上禁用HDR。 GamePlus- 主菜单 5向键进行 GamePlus-FPS 计数器 GamePlus- 十字瞄准线 GamePlus GamePlus GamePlus 动态十字瞄准线 FPS FPS 计数器 禁用 禁用 十字瞄准线 (Practice Mode) FPS 狙击手 (Practice Mode) 定时器 秒表 NEXT BACK/EXIT GamePlus- 定时器 NEXT BACK/EXIT NEXT BACK/EXIT GamePlus- 狙击手 GamePlus 禁用 1.2x 1.2x 1.5x 1.5x 2.0x 2.0x NEXT 5. BACK/EXIT 关闭按钮: • 退出OSD菜单。 • 开启OSD菜单。激活所选的 OSD 菜单项目。 • 增加/减小值或向上/下/左/右移动选择。 6.
2.
2.2 外形尺寸 单位:mm [ 英寸 ] 314.09 [12.4] 87.12 [3.4] 728.18 [28.7] 170.1 [6.7] 100 [3.9] 609.36 [24.0] 84.03 [3.3] 9.85 [.4] 20.84 [.8] 131.4 [5.2] 111.35 [4.4] 428.52 [16.9] 9.16 [.4] 9.85 [.4] 100 [3.9] 158.42 [6.2] 314.09 [12.4] 3.4 [.1] 279.93 [11.
2.3 卸下支撑臂/底座(VESA壁挂安装时) • 避免损坏显示器表面。在卸下显示器底座时,务必将显示器放 在其EPS包装中。 此显示器的可拆卸底座是专为 VESA 壁挂安装而设计的。 卸下支撑臂/底座 1. 拔掉电源线和信号线。小心地将显示器正面朝下放在其EPS包装上。 2. 取下显示器和支撑臂结合部位的护盖。 3. 取下用于将支撑臂固定在显示器后部的四(4)个螺丝。 4. 从显示器上卸下底座(支撑臂和底座)。 2 2 1 1 M4*0.7 • 2-3 仅使用取得UL认证的壁挂装配架,最小重量/承重28.
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 DisplayPort 3840x2160@144Hz 比赛模式 ROG Strix XG32UQ HDR OFF 游戏 超频 图像 动态OD 色彩 Adaptive-Sync 输入选择 ELMB/ELMB SYNC PIP/PBP设置 GamePlus MyFavorite GameVisual 系统 Shadow Boost MOVE/ENTER BACK EXIT 1. 按5向按钮的中间位置以显示OSD菜单。 2. 按向上和向下键切换菜单中的选项。在从一个图标移到另一个图标 时,选项名称高亮显示。 3. 如要选择菜单中高亮显示的项目,请按向右键或中间按钮。 4. 按向上和向下键选择所需的参数。 5. 按向右键或中间按钮进入滑块,然后使用向上或向下键(视菜单中的 指示器而定)进行更改。 6.
3.1.2 1.
2.
• 当滤蓝光激活时,将自动导入比赛模式的默认设置。 • 用户可以在 1级与 3级之间配置亮度功能。 • 4级为最佳设置。它兼容 TUV 低蓝光认证。用户不能配置亮度 功能。 请参考下述说明以缓解眼睛疲劳: 3-4 • 用户长时间工作后,应停止注视显示屏一段时间。建议在使用 电脑连续工作1小时后,休息片刻(至少5分钟)。经常稍事休 息比单次长时间休息更有效。 • 为了尽量减轻眼睛疲劳和干涩,用户应定期休息眼睛,注视一 会儿远方的景物。 • 眼保健操有助于舒解眼睛疲劳。经常做眼保健操。如果眼睛持 续疲劳,请就医。眼保健操:(1) 反复地向上和向下看 (2) 缓慢 地转动眼球 (3) 斜着移动眼球。 • 高能蓝光容易导致眼睛疲劳和AMD(老年性黄斑变性)。滤蓝 光能减少70%(最多)有害蓝光,从而避免CVS(电脑视力综 合症)。 第 3 章:一般说明
3. 色彩 利用此功能选择您喜欢的图像颜色。 DisplayPort 3840x2160@144Hz 比赛模式 ROG Strix XG32UQ HDR OFF 游戏 显示颜色空间 图像 色温 色彩 饱和度 输入选择 灰度系数 PIP/PBP设置 MyFavorite 系统 BACK MOVE/ENTER EXIT • 显示颜色空间:包含三种预设颜色模式:sRGB、DCI-P3和宽色域 模式。 • 色温:包含三种预设颜色模式(6500K、7500K、9300K)和用户 模式。 • 饱和度:调整范围是 0 到 100。 • 灰度系数:包含3个灰度系数模式,包括1.8、2.0、2.2、2.4、2.6。 • 4.
5.PIP/PBP设置 利用 PIP/PBP 设置可以打开所连接的视频源的子窗口。 DisplayPort 3840x2160@144Hz 比赛模式 ROG Strix XG32UQ HDR OFF 游戏 PIP/PBP模式 图像 PIP/PBP源 色彩 色彩设置 输入选择 画中画尺寸 PIP/PBP设置 MyFavorite 系统 MOVE/ENTER BACK EXIT • PIP/PBP模式:选择PIP、PBP模式或者将其关闭。 • PIP/PBP源:选择视频输入源:“DisplayPort”、“HDMI-1” 或“HDMI-2”。 • 色彩设置:为每个PIP/PBP窗口设置GameVisual模式。 • 画中画尺寸:将画中画尺寸调整为:“小”、“中”或“大”。 • 6.
• 快捷方式:用户可以选择“GamePlus、GameVisual、动态OD、 亮度、静音、Shadow Boost、对比度、输入选择、HDR设置、滤 蓝光、音量(耳机输出)、自定义设置-1 (加载)、自定义设置-2 ( 加载)”,并设置为快捷键。 • 自定义设置:您可以根据自己的喜好进行设置。 7.
• USB设置:在待机模式期间开启/关闭USB Hub功能。 • 电源指示灯:开启/关闭电源LED指示灯。 • 电源键锁:禁用/启用电源键 • 按键锁:禁用所有按键功能。按住向下按钮五秒以上可以禁用按键 锁功能。 • 电源设置:可以选择标准模式或省电模式。 • 菜单设置:调整OSD画面的菜单位置、菜单时间、透明度和DDC/ CI。 • DisplayPort串流:如果图形卡不兼容DisplayPort 1.4,请选择 DisplayPort 1.1或DisplayPort 1.
3.2 规格 型号 面板尺寸 最大分辨率 亮度(典型) 固有对比度(典型) 视角(CR>10) XG32UQ 32” W (81.3 cm) 3840x2160@160Hz 450尼特(典型),600尼特(HDR) 1000:1 178°(垂直)/178°(水平) 显示颜色数 1073.7M 响应时间 1 ms GtG 来自 HDMI 的声音 HDMI 输入 DisplayPort 输入 PBP USB3.2端口 耳机 开机功耗 是 HDMI2.1 x 2 是 是 上行 x1、下行 x2 (上行未连接时,USB端口无充电功能) 是 < 35 W* (测量200尼特屏幕亮度,不连接音频/ USB/读卡器) 机壳颜色 黑色 省电模式 < 0.5W 关机模式 倾斜 物理含底座尺寸 (WxHxD) 物理不含底座尺寸 (WxHxD) 包装尺寸 (WxHxD) < 0.3W -5° ~ +20° 728.18 x (539.87~459.87) x 279.93 mm 728.18 x 428.52 x 87.12 mm 900 x 526 x 226 mm 净重(约) 8.
3.
3.
视频时序 1920 1080P 视频时序 1920 1080P O O O 59.94/60 O O O 视频时序 1920 1080P 视频时序 1920 1080 O O O 119.