Seconde édition Novembre 2020 Copyright © 2020 ASUSTeK COMPUTER INC. Tous droits réservés. Aucune partie de cette publication, y compris les produits et logiciels y étant décrits, ne peut être reproduite, transmise, transcrite, stockée dans un système d’interrogation ou traduite dans une langue quelconque sous quelque forme et par quelque moyen que ce soit, exception faite de la documentation conservée par l’acheteur à des fins de sauvegarde, sans l’autorisation écrite expresse de ASUSTeK COMPUTER INC.
Table des matières Avertissements............................................................................................ iv Informations de sécurité.............................................................................. v Soin & Nettoyage......................................................................................... vi Takeback Services...................................................................................... vii Chapitre 1 : Présentation du produit 1.1 Bienvenue !...
Avertissements Déclaration de la Commission Fédérale des Télécommunications (FCC) Cet appareil est conforme à la section 15 du règlement de la FCC. Son fonctionnement est sujet aux deux conditions suivantes : • Cet appareil ne doit pas causer d’interférences nuisibles, et • Cet appareil doit être capable d’accepter toutes les interférences, y compris les interférences pouvant provoquer un fonctionnement indésirable.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouiller du Canada. Informations de sécurité • Avant d’installer le moniteur, lisez attentivement toute la documentation qui accompagne la boîte. • Pour éviter tout incendie ou électrocution, n'exposez jamais le moniteur à la pluie ni à l'humidité. • N’essayez jamais d’ouvrir le boîtier du moniteur.
• Si vous rencontrez des problèmes techniques avec le moniteur, contactez un technicien de réparation qualifié ou votre revendeur. • L’ajustement du contrôle de volume ainsi que l’égaliseur à d’autres réglages que la position centrale peut augmenter la tension de sortie du casque ou des écouteurs et donc le niveau de pression acoustique. • L’adaptateur est utilisé seulement pour ce moniteur, ne l’utilisez pas à d’autres fins.
Conventions utilisées dans ce guide ATTENTION : Informations pour éviter de vous blesser en essayant de terminer un travail. AVERTISSEMENT : Informations pour éviter d’endommager les composants en essayant de terminer un travail. IMPORTANT : Informations que vous DEVEZ suivre pour terminer une tâche. REMARQUE : Astuces et informations supplémentaires pour aider à terminer un tâche.
viii
1.1 Bienvenue ! Merci d’avoir acheté le moniteur LCD d’ASUS® ! Le dernier moniteur à écran LCD large d’ASUS offre un affichage plus large, plus lumineux et d’une clarté cristalline, en plus de toute une gamme de fonctions qui améliorent votre séance de visionnage. Avec ces fonctions du moniteur, vous pouvez profiter du confort et vous régaler d’une expérience visuelle ! 1.
1.3 Présentation du moniteur 1.3.1 Vue de devant/latérale 6 1 2 3 4 5 1. Bouton ( 5 directions) • Active le menu OSD. Active l’élément du menu OSD sélectionné. • Augmente/diminue les valeurs ou déplace votre sélection en haut/ bas, à gauche/droite. • Active le menu OSD quand le moniteur entre en mode veille ou affiche le message « PAS DE SIGNAL ». 2. Bouton • Quitte l’élément du menu OSD. • Bascule la fonction Serrure entre activée et désactivée avec un appui long pendant 5 secondes.
4. Bouton • Valeur par défaut : GameVisual. • Pour modifier la fonction du raccourci, allez dans le menu Raccourci > Raccourci 2. • Active le menu OSD quand le moniteur entre en mode veille ou affiche le message « PAS DE SIGNAL ». 5. Bouton d’alimentation/voyant d’alimentation • Pour allumer ou éteindre le moniteur. • Les couleurs du témoin d’alimentation sont indiquées dans le tableau ci-dessous. 6.
5. Port en émission USB 3.0. Ce port est utilisé pour connecter un câble en amont USB. La connexion active les ports USB du moniteur. 6. Ports en réception USB 3.0. Ces ports permettent de connecter des appareils USB, comme un clavier/une souris USB, un lecteur de mémoire flash USB, et. 7. Port en réception USB 3.0 (port rouge) avec NVIDIA Reflex Latency Analyzer. Ce port est destiné à la connexion de périphériques USB, tels que clavier/souris USB, clé USB, etc.
Menu principal GamePlus GamePlus — Viseur GamePlus — Minuterie GamePlus GamePlus GamePlus GamePlus — Compteur de FPS GamePlus FPS Viseur (Mode d'entraînement) Minuterie Chronomètre FPS Compteur de FPS Alignement écran NEXT 1.3.4 BACK/EXIT NEXT BACK/EXIT NEXT BACK/EXIT NEXT BACK/EXIT Fonction GameVisual La fonction GameVisual vous aide à sélectionner facilement les différents modes d’affichage. Pour activer GameVisual : 1. Appuyez le bouton de raccourci GameVisual. 2.
1.3.5 • En Mode course, la fonction suivante n’est pas configurable par l’utilisateur : Saturation sur six axes. • En Mode sRGB, les fonctions suivantes ne sont pas configurables par l’utilisateur : Température Couleur, Luminosité, Contraste, Gamma, Saturation sur six axes. • En Mode Paysage/Cinéma, les fonctions suivantes ne sont pas configurables par l’utilisateur : Gamma, Optimisation des noirs. G-SYNC HDR Le moniteur prend en charge le format HDR.
Moniteur LCD Série PG259QN/PG259QNR 360Hz d’ASUS 1-7
1-8 Chapitre 1 : Présentation du produit
2.1 Assemblage de la base/du bras du moniteur 1. Insérez la base dans le bras. 2. Assurez la base au bras en serrant la vis. Nous vous conseillons de couvrir la surface de la table avec un chiffon doux pour éviter d’endommager le moniteur. Taille de vis de la base : M6 x 15 mm.
2.2 Utiliser le C-Pince (pour PG259QNR) Le C-Pince permet de fixer le moniteur sur des surfaces pouvant atteindre 8 cm d’épaisseur. Avant de commencer, assurez-vous que vous disposez de suffisamment d’espace pour l’ensemble de la pince et que la surface est solide et plane. Suivez les illustrations ci-dessous pour monter le moniteur. 3 2 1 4cm 6cm 2 3 8cm 1 *Desserrez la vis avant de retirer le support intérieur de la pince.
2.3 Gestion des câbles Vous pouvez organiser les câbles à l’aide du couvercle du port entrée/sortie. • Organiser les câbles • Utiliser couvercle du port entrée/sortie : le couvercle peut être installé ou retiré. 2.4 Réglage du moniteur • Pour une vision optimale, il est recommandé d'avoir une vision de face sur le moniteur, ensuite réglez l'angle du moniteur pour qu'il soit confortable. • Tenez le pied pour empêcher le moniteur de tomber quand vous le changez d’angle.
Il est normal que le moniteur tremble légèrement quand vous ajustez l’angle de visualisation. Pivoter le moniteur 1. Soulevez le moniteur dans sa position la plus haute. 2. Inclinez le moniteur à l’angle maximum permis. 3. Tournez le moniteur vers la droite jusqu’à l’angle désirée. 0° -5° ~ +20° 90° 0° 90° Il est normal que le moniteur tremble légèrement quand vous ajustez l’angle de visualisation.
2.5 Démontage du bras (montage mural VESA) Le bras détachable de ce moniteur, est spécialement conçu pour une installation murale VESA. Pour démonter le bras : 1. Couchez le moniteur sur une table face vers le bas. 2. Utilisez un tournevis pour retirer les couvercles là où le moniteur et le bras se rejoignent. 3. Desserrez les quatre vis à l’arrière du moniteur et enlevez le bras/la base.
2.6 Branchement des câbles Branchez les câbles selon les instructions suivantes : Pour le service uniquement PG259QNR PG259QN • • Pour brancher le cordon d’alimentation : a. Connectez l’adaptateur d’alimentation sur l’entrée DC IN du moniteur. b. Connectez une extrémité du cordon d’alimentation à l’adaptateur d’alimentation et l’autre extrémité à une prise électrique. Pour brancher le câble DisplayPort/HDMI : a.
Moniteur LCD Série PG259QN/PG259QNR 360Hz d’ASUS 2-7
2-8 Chapitre 2 : Installation
3.1 Menu OSD (Affichage à l’écran) 3.1.1 Reconfiguration Mode normal DisplayPort 1920x1080@360 Hz HDR désactivé Mode G-SYNC Esports Mouse Detected ROG Swift 360Hz PG259QNR ® G-SYNC Processor NVIDIA Reflex Latency Analyzer Jeux NVIDIA ULMB Image ULMB Pulse Width Couleur Sélection Entrée Raccourci Effet d'éclairage Configuration Système BACK MOVE/ENTER ( EXIT 1. Appuyez le bouton 2. Déplacez le bouton ( ) en haut/bas pour naviguer dans les fonctions.
3.1.2 1.
* Monitoring Rectangle Location : Ajuste manuellement l’emplacement du rectangle de surveillance à l’aide du bouton ( 5 directions). * Monitoring Rectangle Size : Ajuste manuellement la taille du rectangle de surveillance à l’aide du bouton ( 5 directions). Vous pouvez également télécharger et installer la GeForce Experience pour profiter pleinement de l’analyse de la latence du système. Les étapes de configuration de la GeForce Experience sont les suivantes : a. Installez la GeForce Experience. b.
Cette fonction n’est pas disponible lorsque NVIDIA ULMB est activé. • GamePlus : Voir 1.3.3 Fonction GamePlus pour des détails. • GameVisual : Voir 1.3.4 Fonction GameVisual pour des détails. • Optimisation des noirs : L’Optimisation des couleurs sombres ajuste la courbe de gamma du moniteur pour enrichir les tons sombres dans une image rendant les scènes et objets sombres beaucoup plus facile à voir. 3.
Veuillez consulter ce qui suit pour alléger la fatigue oculaire : 4. • Vous devez vous éloigner pendant un certain temps de l'affichage si vous travaillez pendant de longues heures. Il est conseillé de faire des pauses courtes (au moins 5 minutes) après environ 1 heure de travail continu à l'ordinateur. Faire des pauses courtes et fréquentes est plus efficace qu'une seule pause plus longue.
5. Sélection Entrée Dans cette fonction, vous pouvez sélectionner la source d’entrée désirée et basculer la fonction de commutation auto d’entrée entre activée et désactivée. Mode normal DisplayPort 1920x1080@360 Hz HDR désactivé Mode G-SYNC Esports Mouse Detected ROG Swift 360Hz PG259QNR ® G-SYNC Processor DisplayPort Jeux HDMI Image Autocommutateur entrée Couleur Sélection Entrée Raccourci Effet d'éclairage Configuration Système BACK MOVE/ENTER 6.
• Aura Sync : Permet d’activer ou de désactiver la fonction Aura Sync qui synchronise l’effet de lumière Aura RGB parmi tous les périphériques pris en charge. • Aura RGB : Dans cette fonction, vous pouvez sélectionner un effet de lumière Aura RGB pour le moniteur et modifier les paramètres de l’effet de lumière. Sélectionnez « Arrêt » si vous souhaitez désactiver l’effet de lumière Aura RGB. 8. • Si la fonction Aura Sync est réglée sur Marche, la fonction Aura RGB deviendra indisponible. • Voir « 3.
Si le moniteur ne peut pas se réveiller après être entré en veille prolongée, procédez d’une des manières suivantes : - Appuyez sur un bouton (à l’exception du bouton d’alimentation) sur le moniteur pour le réveiller. - Désactivez la fonction Veille prolongée. 3-8 • Serrure : Pour désactiver toutes les touches de fonction. Appuyez sur plus de 5 secondes pour annuler la fonction serrure. • Position-OSD : Pour ajuster la position horizontale (Position-H)/la position verticale (Position-V) du menu OSD.
3.2 Aura Armoury Crate est un logiciel qui contrôle les DÉL colorées sur les périphériques pris en charge, comme les moniteurs, les cartes mères, les cartes graphiques, les PC de bureau, etc. Aura vous permet d’ajuster la couleur des DÉL RVB sur ces périphériques et de sélectionner différents effets de lumière. Vous pouvez également corriger ou ajuster la couleur des DÉL en les étalonnant. Pour activer Aura : 1. Réglez la fonction Aura Sync sur Marche dans le menu OSD. 2. Connectez le port USB 3.
3.3 Résumé des spécifications Type d’affichage TFT LCD Taille de l’écran Écran large 24,5" (16:9, 62,18 cm) Résolution max. 1920 x 1080 Taille des pixels 0,2829 mm x 0,2802 mm Luminosité (Typ.) 400 cd/m2 Rapport de contraste (Typ.) 1000:1 Angle de vision (H/V) CR > 10 178˚/178˚ Couleurs d’affichage 16,7 M Temps de réponse 1 ms (Gris à Gris) Sélection de la température des couleurs 8 températures de couleur Entrée analogique Non Entrée numérique DisplayPort v1.4 x 1, HDMI v2.
Poids (approx.
3.4 Dimensions du contour ASUS PG259 Outline Dimension *Unit: mm(inch) Pivot: +90 Degree 9 0° 20° 5° 161.78 [6.37] 203.02 [7.99] 7.06 [0.28] 151.31 [5.96] 557.29 [21.94] 543.17 (21.38)-Active-Area 271.59 [10.69] 536.53 [21.12] 19.95 [0.79] 6.77 [0.27] 246.74 [9.71] 302.62 (11.91)-Active-Area 330.34 [13.01] 168.86 [6.65] 499.20 [19.65] 25° Swivel: +/-25 Degree 87.95 [3.46] 15.75 [0.62] 27.51 [1.08] 120.00 [4.72] 221.12 [8.71] 411.52 [16.20] 168.86 [6.65] 25° 89.60 [3.53] 116.95 [4.
3.5 Guide de dépannage (FAQ) Problème Solution possible Le voyant DEL d'alimentation n’est pas ALLUMÉ • Appuyez sur le bouton d’alimentation pour vérifier si le moniteur est en mode ALLUMÉ. • Vérifiez si le cordon d'alimentation est correctement branché sur le moniteur et sur la prise de courant. Le voyant DEL d’alimentation est de couleur blanche et il n’y a aucune image sur l’écran • Vérifiez si le moniteur et l’ordinateur sont en mode ALLUMÉ.
Lors de l’exécution de NVIDIA Reflex • Redémarrez PC+Display Latency via l’OSD. Latency Analyzer, « ---- » s’affiche dans le • Redémarrez le moniteur. coin supérieur gauche à chaque clic de la souris et que le rectangle est au-dessus de l’éclat du canon. 3.