用户手册
目录 声明............................................................................................................... iii 安全信息 ....................................................................................................... iv 保养和清洁 .................................................................................................... vi 1.1 欢迎使用 ......................................................................................... 1-1 1.2 物品清单 ......................................................
声明 联邦通信委员会声明 本设备符合 FCC 规则第 15 部分的要求。其操作符合以下两项条件: • 此设备不会产生有害干扰。 • 此设备必须可以承受任何接收到的干扰,包括可能导致不正常操作的干 扰。 此设备经检测,符合 FCC 规则第 15 部分中关于 B 级数字设备的限制规定。 这些限制旨在为居民区安装提供防止有害干扰的合理保护。本设备会产生、 使用并且辐射无线电波,如果不按照说明进行安装和使用,可能会对无线电 通讯产生有害干扰。但是,不能保证在特定安装条件下不会出现干扰。如果 本设备对无线电或电视接收造成了有害干扰(可通过关闭和打开设备电源来 确定),建议用户采取以下一项或多项措施来消除干扰: • 调节接收天线的方向或位置。 • 增大设备与接收器之间的距离。 • 将此设备和接收设备连接到不同电路的电源插座上。 • 向代理商或有经验的无线电/电视技术人员咨询以获得帮助。 为确保符合 FCC 规定,需使用屏蔽线连接显示器和图形卡。若未 经符合性责任方的明确准许而变更或改动此设备,可能会使用户失 去操作此设备的资格。 加拿大通信部声明 此数字设备未超过加拿大通信部无线电干扰条例中规定的数字设备无线电噪 声发
安全信息 • 在设置本显示器之前,请仔细阅读产品包装中附带的所有文档。 • 为防止火灾或电击危险,切勿使本显示器遭受雨淋或受潮。 • 请勿打开显示器机壳。显示器内部有危险高压,可能导致严重人身 伤害。 • 电源发生故障时,不要尝试自行修复。请与专业技术服务人士或经销商 联系。 • 在使用本产品之前,确保所有线缆均连接正确并且电源线没有损坏。 如有任何损坏,请立即与经销商联系。 • 机壳后部和顶部的槽和开口用于通风目的。不要堵塞这些开口。除非 通风良好,否则不要将本产品放置在散热器或热源上部或附近。 • 本显示器只应使用标签上注明的电源类型。如果您不了解家中的电源 类型,请与经销商或当地电力公司联系。 • 使用符合您当地电力标准的合适电源插头。 • 请勿使电源板或延长线过载。过载可能导致火灾或电击。 • 避免灰尘、潮湿和极端温度。不要将显示器放置在可能受潮的任何区域 中。将显示器放置在平稳的表面上。 • 遇有雷雨天气或长时间不使用时,应拔掉设备的电源线。这样做可以 防止因电压突变而损坏显示器。 • 切勿将任何异物塞入或使任何液体溅入显示器机壳上的开口内。 • 为确保正常运行,本显示器只应与 UL 列出的计算机一
警告 由于声压过高,使用其他听筒或耳机可能导致听力受损。 限制有害物质声明(印度) 此产品符合“印度电子废弃物(管理)条例,2016”的要求,在匀质材料 中铅、汞、六价铬、多溴联苯 (PBB) 和多溴二苯醚 (PBDE) 的含量不应该超 过 0.1%,镉的含量不应该超过 0.
保养和清洁 • 在提起或重新放置显示器之前,最好先拔掉线缆和电源线。采用正确的 提起方式放置显示器。提起或搬运显示器时,抓住显示器的边缘。不要 通过底座或线缆提起显示屏。 • 清洁。关闭显示器电源并拔掉电源线。使用不含麻且非研磨性的布清洁 显示器表面。将布在中性清洁剂中蘸湿后擦去顽固污渍。 • 不要使用包含酒精或丙酮的清洁剂。使用液晶专用清洁剂。切勿直接将 清洁剂喷洒在屏幕上,否则清洁剂可能渗入显示器内并导致电击。 打叉的带轮垃圾桶符号表示产品(电子、电气设备和含汞钮扣电池) 不得当作普通生活垃圾处理。请了解当地有关电子产品废弃处理的 有关规定。 AEEE yönetmeliğine uygundur 以下现象对于显示器来说是正常现象: • 由于荧光灯本身的特点,屏幕在初次使用时可能闪烁。关闭电源开关, 然后重新打开,确认闪烁已消失。 • 您可能会发现屏幕上的亮度略微不均匀,这与您使用的桌面图案有关。 • 同一图像显示数小时后,切换图像时可能残留前一个屏幕显示的图像。 屏幕会慢慢恢复,或者您可以关闭电源开关数小时。 • 当屏幕变黑或闪烁时或者无法继续工作时,请与经销商或服务中心联系 进行修理。不要自行修理屏
更多信息 如需更多信息或者产品和软件更新,请使用下列资源。 1. ASUS 网站 ASUS 全球网站提供关于 ASUS 硬件和软件产品的更新信息,网址是 http://www.asus.com 2.
1.1 欢迎使用 感谢您购买 ASUS® 液晶显示器! 这是 ASUS 最新推出的宽屏液晶显示器,它不但提供更艳丽、更宽、更亮 的显示屏,而且通过一些有用的功能丰富您的观看体验。 通过这些功能,此显示器可为您提供方便愉快的视觉体验! 1.2 物品清单 检查包装中是否包括下列物品: 液晶显示器 显示器底座 快速入门指南 保修卡 1 条电源线 1 条 HDMI 电缆线 1 条 DP 线 1 个电源适配器 1 条 USB 3.
1.3 组装显示器 组装显示器: • 在安装显示器支撑臂/底座时,我们建议您将显示器放在其 EPS(发泡聚苯乙烯)包装内进行。 1. 将支撑臂上的螺丝孔对准底座上附带的螺丝。然后,将底座插入 支撑臂。 2. 拧紧附带的螺丝,将底座固定到支撑臂上。 3.
1.4 连接线缆 1.4.1 液晶显示器后部 9 DCIN 1 2 1. 直流输入端口 2. USB3.0上行端口 3. USB3.0下行端口 4. USB3.0下行端口 5. HDMI2.0端口 6. HDMI2.0端口 7. DisplayPort 8. 耳机插孔 9.
1.5 显示器简介 1.5.1 使用控制按钮 使用显示器背面的控制按钮调整显示器设置。 6 6 5 5 4 4 3 3 2 2 1 1. 电源指示灯: • 下表介绍电源指示灯的颜色定义。 2. 状态 说明 白色 开机 黄色 待机模式 关闭 关闭 电源键: • 按此按钮打开/关闭显示器的电源。显示器关闭时,按此按钮开启 显示器。 3. GameVisual: • 利用此热键,可以切换采用GameVisual™视频智能技术的八种 视频预设模式(风景模式、比赛模式、影院模式、RTS/RPG模 式、FPS模式、sRGB模式、MOBA模式和用户模式)。 4.
• 按GamePlus按钮进入GamePlus主菜单。 • 激活十字瞄准线、定时器、FPS计数器或显示对齐等功能。 • 向上/向下移动 的功能。按 按钮进行选择,然后按 确认所需 离开和退出。 • 十字瞄准线/定时器/FPS计数器可以通过按 移动。 5向键进行 • 为了激活狙击手,您需要在设备上禁用HDR。 GamePlus- 主菜单 GamePlus十字瞄准线 GamePlus- 定时器 十字瞄准线 (Practice Mode) 定时器 FPS 计数器 显示对齐 狙击手 GamePlus- 狙击手 5. 关闭按钮: • 退出OSD菜单。 6.
2.
2.
2.3 卸下支撑臂/底座(VESA壁挂安装时) • 避免损坏显示器表面。在卸下显示器底座时,务必将显示器 放在其EPS包装中。 此显示器的可拆卸底座是专为 VESA 壁挂安装而设计的。 卸下支撑臂/底座 1. 拔掉电源线和信号线。小心地将显示器正面朝下放在其EPS包装上。 2. 取下显示器和支撑臂结合部位的护盖。 3. 取下用于将支撑臂固定在显示器后部的四(4)个螺丝。 4. 从显示器上卸下底座(支撑臂和底座)。 2 2 1 1 • 仅使用取得UL认证的壁挂装配架,最小重量/承重28.
3.1 OSD(屏幕显示)菜单 3.1.1 如何重新配置 DisplayPort 2560x1440@165Hz 风景模式 Aura Off ROG Swift PG329Q HDR OFF 游戏 超频 图像 可变OD 色彩 Adaptive-Sync 输入选择 ELMB/ELMB SYNC PIP/PBP设置 GamePlus 灯光效果 GameVisual MyFavorite Shadow Boost 系统 MOVE/ENTER BACK EXIT 1. 按5向按钮的中间位置以显示OSD菜单。 2. 按向上和向下键切换菜单中的选项。在从一个图标移到另一个图标 时,选项名称高亮显示。 3. 如要选择菜单中高亮显示的项目,请按向右键或中间按钮。 4. 按向上和向下键选择所需的参数。 5. 按向右键或中间按钮进入滑块,然后使用向上或向下键(视菜单中的 指示器而定)进行更改。 6.
3.1.2 1.
2.
• 当滤蓝光激活时,将自动导入比赛模式的默认设置。 • 用户可以在 1级与 3级之间配置亮度功能。 • 4级为最佳设置。它兼容 TUV 低蓝光认证。用户不能配置亮度 功能。 请参考下述说明以缓解眼睛疲劳: • 用户长时间工作后,应停止注视显示屏一段时间。建议在使用 电脑连续工作1小时后,休息片刻(至少5分钟)。经常稍事休 息比单次长时间休息更有效。 • 为了尽量减轻眼睛疲劳和干涩,用户应定期休息眼睛,注视一 会儿远方的景物。 • 眼保健操有助于舒解眼睛疲劳。经常做眼保健操。如果眼睛持 续疲劳,请就医。眼保健操:(1) 反复地向上和向下看 (2) 缓慢 地转动眼球 (3) 斜着移动眼球。 • 高能蓝光容易导致眼睛疲劳和AMD(老年性黄斑变性)。滤蓝 光能减少70%(最多)有害蓝光,从而避免CVS(电脑视力综 合症)。 ASUS LCD 显示器 PG 系列 3-3
3. 色彩 利用此功能选择您喜欢的图像颜色。 DisplayPort 2560x1440@165Hz 风景模式 Aura Off ROG Swift PG329Q HDR OFF 游戏 色温 图像 灰度系数 色彩 饱和度 输入选择 PIP/PBP设置 灯光效果 MyFavorite 系统 BACK MOVE/ENTER EXIT • 色温:包含三种预设色彩模式(冷色温、常规色、暖色温) 和用户模式。 • 灰度系数:包含三种灰度系数模式:1.8、2.2、2.5。 • 饱和度:调整范围是 0 到 100。 • 在用户模式下,用户可以配置红(红色)、绿(绿色)和蓝( 蓝色),调整范围是 0 ~ 100。 4.
5.
6. 灯光效果 DisplayPort 2560x1440@165Hz 风景模式 Aura Off ROG Swift PG329Q HDR OFF 游戏 Aura Sync 图像 Aura RGB 色彩 输入选择 PIP/PBP设置 灯光效果 MyFavorite 系统 BACK MOVE/ENTER EXIT • Aura Sync:允许您开启或关闭Aura Sync功能,它能同步所支持 的全部设备的Aura RGB光效果。 • Aura RGB:利用此功能,您可以为显示器选择一种Aura RGB光 效果,并更改光效果设置。如要关闭Aura RGB光效果,请选择“ 禁用”。 • Aura Sync功能开启时,Aura RGB功能不可用。 7.
8.
3-8 • USB Hub:在待机模式期间开启/关闭USB Hub功能。 • 电源指示灯:使电源 LED 指示灯点亮/熄灭。 • 电源键锁:禁用/启用电源键 • 按键锁:禁用所有按键功能。按住向下按钮五秒以上可以禁用按键 锁功能。 • 菜单设置:调整OSD画面的菜单时间、DDC/CI和透明度。 • DisplayPort 版本:如果图形卡不兼容DP 1.4,请选择DP 1.
3.2 规格 型号 面板尺寸 最大分辨率 亮度(典型) 固有对比度(典型) 视角(CR>10) 显示颜色数 响应时间 来自 HDMI 的声音 HDMI 输入 DisplayPort 输入 PBP USB3.0端口 耳机 开机功耗 PG329Q 32” W (81.3 cm) 2560 x 1440 @175Hz(超频) 400尼特(典型),600尼特(峰值) 1000:1 178°(垂直)/178°(水平) 1.07B 1 ms(G到G) 是 HDMI2.0 x 2 是 是 上行 x1、下行 x2 (上行未连接时,USB端口无充电功能) 是 < 43 W* (测量200尼特屏幕亮度,不连接音频/ USB/读卡器) 机壳颜色 黑色 省电模式 < 0.5W 关机模式 倾斜 < 0.5W -5° ~ +20° 物理含底座尺寸 (WxHxD) 728.18 x 551.83 x 292.56 mm 物理不含底座尺寸 (WxHxD) 728.18 x 428.52 x 87.12 mm 包装尺寸 (WxHxD) 812 x 238 x 626 mm 净重(约) 9.
3.
3.
视频时序 视频时序 2560 3840 1440 2160 175 59.