使用手冊
目錄 注意事項 ....................................................................................................... iii 安全資訊 ....................................................................................................... iv 維護與清潔 .................................................................................................... vi 1.1 歡迎使用 ......................................................................................... 1-1 1.2 包裝內容 ...........................................................
注意事項 聯邦通訊委員會 (FCC) 聲明 本裝置符合 FCC 條款第 15 部份的規定。操作程序受限於下列兩項條件: • 本裝置不會造成有害干擾。 • 本裝置須能承受任何可接收的干擾,包括可能導致意外操作的干擾。 本設備經測試符合 FCC 條款第 15 部份關於 B 類數位裝置的規定。這些限 制之主要目的乃針對在住宅區內安裝裝置時,提供有害干擾的合理保護。本 設備會產生、使用並放射無線射頻能量,如未根據本指示方法安裝和使用本 設備,可能會對無線電通訊造成有害干擾。然而,我們無法保證在特定環境 下安裝此設備不會造成任何干擾。若本設備確實對無線電或電視接收造成不 良干擾(請開關設備加以確認),您可採取以下方式改善干擾情形: • 重新調整收訊天線的方向或位置。 • 將設備與接收器之間的距離加大。 • 將設備與接收器插至使用不同電路的電源插座。 • 向有經驗的無線電 電視技術人員尋求協助。 連接螢幕與顯示卡需使用屏蔽纜線以確保遵循 FCC 規範。未經負 責遵循方明確核准變更或修改本機可能造成使用者操作本設備的權 限失效。 加拿大通訊部聲明 根據加拿大通訊部於無線電干擾法規中針對數位裝置產生無
安全資訊 iv • 安裝本顯示器之前,請詳閱產品包裝內的說明文件。 • 為避免起火或觸電,請勿將顯示器暴露於下雨或潮濕的環境中。 • 切勿嘗試打開顯示器機殼。顯示器內的高壓電可能會造成嚴重的人身傷 害。 • 若電源中斷,切勿嘗試自行修復。請洽詢合格維修技術人員或經銷商。 • 使用本產品前,請務必正確連接所有纜線,並確認電源線並未損壞。若 發現任何損壞情形,請立即洽詢經銷商。 • 機殼背面或頂端的狹槽和開口為通風孔;請勿堵塞這些狹槽。除非通風 良好,否則切勿將本產品放至於散熱器或熱源附近或上方。 • 本顯示器只能使用標籤上註明的電源類型運作。若您不確定府上的電源 類型,請洽詢經銷商或當地的電力公司。 • 請使用符合當地電源標準的電源插頭。 • 請勿讓排插和延長線過載。電源過載可能會引發火災或造成觸電。 • 請避開多塵、潮濕和溫度過高 過低的環境。請勿將顯示器放置於任何 可能潮濕之處。請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本裝置的插頭,避免顯示器因電源 突波而造成損壞。 • 切勿將任何異物塞入顯示器機殼開口內,也不可讓液體潑灑流入。
警告 使用非指定耳機可能會因音壓過大導致聽力受損。 有害物質限制聲明(印度) 本產品遵守「2016 印度電子廢棄物(管理)規定」並除本規定表 2 列出之 免除項目外,禁止在均勻材質重量中使用濃度超過 0.1% 的鉛、汞、六價鉻、 多溴聯苯 (PBBs) 和多溴二苯醚 (PBDEs),以及在均勻材質重量中使用濃度 超過 0.
維護與清潔 • 抬起顯示器或變更顯示器位置前,請先拔下纜線和電源線。放置顯示器 時,請依照正確的方式抬起顯示器。抬起或移動顯示器時,請抓住顯示 器的邊緣;切勿只抓住底座或電源線。 • 清潔:請關閉顯示器電源並拔下電源線。使用不會造成刮傷的軟布清潔 顯示器表面,並以軟布沾少許中性清潔劑清除頑垢。 • 避免使用含酒精或丙酮的清潔劑。請使用液晶顯示器專用的清潔劑。 切勿將清潔劑直接噴灑在螢幕上,以免滲入顯示器內並引起觸電。 此垃圾桶畫叉符號代表該產品(電氣、電子設備及內含水銀鈕釦 電池)不得投入一般廢棄物中。請查閱當地電子產品棄置法規。 AEEE yönetmeli ine uygundur 以下徵狀為顯示器正常現象: • 第一次使用本顯示器時,螢幕可能會因螢光燈的自然特性而出現閃爍 的情形。請關閉電源並重新開啟,即可讓閃爍情況消失。 • 不同的桌面圖案可能會造成螢幕出現輕微亮度不均的情況。 • 顯示同樣的影像數小時後,當您切換影像時,可能會出現原有影像的 殘影。螢幕畫面會慢慢恢復正常,關閉電源開關數小時也可以改善此 情況。 • 螢幕變黑、閃爍或無法運作時,請交由經銷商或維修中心處理。切勿
更多詳細資訊 如需其他資訊以及產品 軟體更新,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供關於 ASUS 硬體和軟體產品的最新資訊。 請參閱 http://www.asus.com 2.
1.1 歡迎使用 感謝您購買 ASUS® 液晶顯示器! ASUS 最新的寬螢幕液晶顯示器提供更清晰、更寬廣、更鮮明的畫面顯示, 以及許多增強觀賞體驗的功能。 透過這些功能,您可以盡情享受本顯示器所帶來的便利性及愉快的視覺體 驗! 1.2 包裝內容 請檢查包裝內是否包含下列物品: 液晶顯示器 顯示器底座 快速使用指南 保固卡 1 x 電源線 1 x HDMI 纜線 1 x DP 纜線 1 x 整流器 1 x USB 3.
1.3 調整顯示器 組裝顯示器的方法如下: • 在組裝顯示器支架/底座時,建議您保留顯示器內部的 EPS (膨脹性聚苯乙烯)包裝。 1. 對準顯示器支架上的螺絲孔和底座上的隨附螺絲。然後將底座插入顯 示器支架中。 2. 鎖緊隨附螺絲以固定顯示器支架上的底座。 3.
1.4 連接纜線 1.4.1 液晶顯示器背面 9 DCIN 1 2 3 1. DC-IN 連接埠 2. USB3.0 上行連接埠 3. USB3.0 下行連接埠 4. USB3.0 下行連接埠 5. HDMI2.0 連接埠 6. HDMI2.0 連接埠 7. DisplayPort 8. 耳機插孔 9.
1.5 顯示器簡介 1.5.1 使用控制鈕 使用顯示器背面的控制鈕來調整顯示器設定。 6 6 5 5 4 4 3 3 2 2 1 1. 電源指示燈: • 2. 狀態 說明 白 開 琥珀 待機模式 關 關 電源按鈕: • 按下此按鈕可開啟 關閉顯示器電源。顯示器電源關閉時,按下此 按鈕即可開啟顯示器。 • 按下此快速鍵切換八種採用 GameVisual™ 影像智慧型技術的預 設影像顯示模式 (風景模式、比賽模式、電影模式、RTS/RPG 模 式、FPS 模式、sRGB 模式、MOBA 模式及使用者模式)。 • GamePlus:GamePlus 功能含有工具套件,可在玩不同類型的遊 戲時,為使用者建立更出色的遊戲環境。尤其,十字瞄準線功能是 特別為了對第一人稱射擊(FPS)遊戲感興趣的新玩家或新手而設 計的。 若要啟動 GamePlus: 3. GameVisual: 4.
• 選擇 GamePlus 按鈕,以進入 GamePlus 主選單。 • 啟動十字瞄準線、定時器或 FPS 計數器或顯示對齊功能。 • 向上 向下移動 能。按壓 按鈕以選擇並按下 確認所需功 即可關閉,然後離開。 • 按下 5 向鍵可移動十字瞄準線/定時器/FPS 計數器。 • 若要啟動狙擊手,您必須停用裝置的 HDR 功能。 GamePlus 主選單 GamePlus 十字瞄準線 GamePlus - 定時器 十字瞄準線 (Practice Mode) 定時器 FPS 計數器 顯示對齊 狙擊手 GamePlus - 狙擊手 5. 關閉按鈕: • 6.
2.
2.
2.3 拆卸支架 底座(適用於 VESA 壁掛式安裝) • 避免破壞顯示器表面。拆卸顯示器底座時,請務必保留顯示器 內部的 EPS 包裝。 本顯示器的可拆式底座是特別針對 VESA 壁掛式安裝所設計。 拆卸支架 底座 1. 拔下電源線和訊號線。小心讓顯示器正面朝下並放入 EPS 包裝。 2. 拆下顯示器與支架專用的外蓋。 3. 拆下固定支架至顯示器背面的四 (4) 支螺絲。 4. 自顯示器拆下底座(支架及底座)。 2 2 1 1 M4*0.7 • 僅限使用 UL 所列重量/負載 28.
3.1 OSD(螢幕功能顯示)選單 3.1.1 如何重新設定 DisplayPort 2560x1440@165Hz 風景模式 Aura Off ROG Swift PG329Q HDR OFF 遊戲 超頻 影像 可變外徑 色彩 Adaptive-Sync 輸入選擇 ELMB/ELMB SYNC PIP/PBP 設定 GamePlus 燈光效果 GameVisual MyFavorite Shadow Boost 系統設定 MOVE/ENTER BACK EXIT 1. 按下中央 5 向按鈕以顯示 OSD 選單。 2. 按下向上與向下鍵可切換選單中的選項。在圖示間移動時,選項名稱 會反白顯示。 3. 若要選擇選單中的反白項目,請按下右鍵或中央按鈕。 4. 按下向上及向下鍵可選擇所需的參數。 5. 按下向右鍵或中央按鈕可進入滑動桿,然後使用向上或向下鍵(視選 單中的指標而定)進行變更。 6.
3.1.2 1.
2.
• 啟動濾藍光時,將自動匯入比賽模式的預設設定。 • 濾藍光功能為 1級至 3級之間時,使用者可自行設定亮度。 • 4級為最佳化設定。此設定符合 TUV 低藍光認證。使用者無法 自行設定亮度。 請參閱下列說明以舒緩眼睛疲勞: • 使用者若長時間工作,應遠離顯示器一段時間。建議在電腦前 連續工作 1 小時後休息片刻(至少 5 分鐘)。短暫且頻繁的休 息遠比單次長時間休息有效率。 • 為減少您的眼睛疲勞及乾澀狀態,使用者應定時注視遠方物體 以讓眼睛休息。 • 眼部活動可有助減少眼睛疲勞。請經常重複這些活動。若持續 感到眼睛疲勞,請就醫。眼部活動:(1) 朝上下方反覆觀看 (2) 緩慢轉動眼球 (3) 以對角方向移動眼球。 • 大量藍光可能會造成眼睛疲勞及 AMD (老年性黃斑部病變) 。濾藍光可減少 70% (最多)的有害藍光,避免產生 CVS (電腦視覺症候群)。 ASUS LCD 顯示器 PG 系列 3-3
3. 色彩 請利用此功能選取您喜歡的色彩。 DisplayPort 2560x1440@165Hz 風景模式 Aura Off ROG Swift PG329Q HDR OFF 遊戲 色溫 影像 Gamma 色彩 彩度 輸入選擇 PIP/PBP 設定 燈光效果 MyFavorite 系統設定 BACK MOVE/ENTER • 色溫:包含三種預設色彩模式(冷色溫、正常、暖色溫), 以及使用者模式。 • Gamma:包含三種含 1.8、2.2、2.5 的 Gamma 模式。 • 彩度:調整範圍從 0 到 100。 • 4.
5.
6. 燈光效果 DisplayPort 2560x1440@165Hz 風景模式 Aura Off ROG Swift PG329Q HDR OFF 遊戲 Aura Sync 影像 Aura RGB 色彩 輸入選擇 PIP/PBP 設定 燈光效果 MyFavorite 系統設定 BACK MOVE/ENTER • Aura Sync:允許您開啟或關閉同步化所有支援裝置間的 Aura RGB 照明效果的 Aura Sync 功能。 • Aura RGB:您可在此功能中選擇顯示器的 Aura RGB 照明效果和 變更照明效果設定。若您要關閉 Aura RGB 照明效果,請選擇「 關」。 • 7.
8.
3-8 • USB Hub:在待機模式期間開啟/關閉 USB Hub 功能。 • 電源指示燈:開啟 • 電源鍵鎖:若要停用 • 按鍵鎖:停用所有的按鍵功能。按下向下按鈕超過五秒可停用按鍵 鎖定功能。 • 選單設定:調整 OSD 畫面的選單時間、DDC/CI 及透明度。 • DisplayPort版本:若您的應用程式顯示卡不相容於 DP 1.4,請選 擇 DP 1.
3.2 規格 機型 面板尺寸 最大解析度 亮度(一般) 固有對比度(一般) 可視角度 (CR>10) PG329Q 32" W (81.3 cm) 2560 x 1440@175Hz(超頻) 400 nits(標準值),600 nits(峰值) 1000:1 178°(垂直) 178°(水平) 顯示色彩 1.07B 反應時間 1 ms (G 至 G ) HDMI 音效 是 HDMI 輸入 HDMI2.0 x 2 DisplayPort 輸入 PBP USB3.0 連接埠 耳機 開機耗電量 是 是 上行 x1,下行 x2 (上行無連結時,代表 USB 連接埠無充 電器) 是 < 43 W* (在無音訊/ USB/ 讀卡機連線時測量 200 nits 畫面亮度) 機殼顏色 黑色 省電模式 < 0.5W 關機模式 < 0.5W 傾斜角度 -5° ~ +20° 實體尺寸含底座(寬x高x深) 728.18 x 551.83 x 292.56 mm 實體尺寸不含底座(寬x高x 深) 728.18 x 428.52 x 87.
3.
3.
視訊時序 視訊時序 2560 3840 1440 2160 175 59.