MANUE L D E L' U T I L I S AT E U R
Table des matières Avertissements............................................................................................ iii Informations de sécurité............................................................................. iv Soin & Nettoyage......................................................................................... vi 1.1 Bienvenu........................................................................................ 1-1 1.2 Contenu de la boîte.....................................
Avertissements Déclaration de la Commission Fédérale des Télécommunications (FCC) Cet appareil est conforme à la section 15 du règlement de la FCC. L'utilisation est permise sujette aux deux conditions suivantes : • Cet appareil ne peut pas causer d'interférences nocives. • Cet appareil doit pouvoir accepter toutes les interférences reçues, y compris les interférences risquant d’engendrer un fonctionnement indésirable.
Informations de sécurité iv • Avant d’installer le moniteur, lisez attentivement toute la documentation qui accompagne la boîte. • Pour réduire le risque d’incendie ou de choc électrique, n’exposez jamais le moniteur à la pluie ou à l’humidité. • N’essayez jamais d’ouvrir le boîtier du moniteur. Les hautes tensions dangereuses à l’intérieur du moniteur peuvent entraîner de graves blessures corporelles. • Si l'alimentation électrique est cassée, n'essayez pas de la réparer par vous-même.
• Fournissez une connexion de mise à la terre avant de brancher la prise principale sur le secteur. Lorsque vous débranchez une connexion de mise à la terre, veuillez la débrancher seulement après avoir débranché la prise principale du secteur. • Veuillez utiliser l'adaptateur ADP-150CH B de DELTA. • Veuillez vérifier que le système de distribution de l’installation du bâtiment inclut un disjoncteur de 120/240V, 20A (maximum).
Soin & Nettoyage • Avant de soulever ou de déplacer votre moniteur, il est préférable de débrancher les câbles et le cordon d’alimentation. Suivez les bonnes techniques de levage quand vous soulevez le moniteur. Quand vous soulevez ou transportez le moniteur, tenez les bords du moniteur. Ne soulevez pas le moniteur en tenant le support ou le cordon d’alimentation. • Nettoyage. Éteignez votre moniteur et débranchez le cordon d’alimentation.
Où trouver plus d’informations Référez-vous aux sources suivantes pour les informations supplémentaires et pour les mises à jour de produit et logiciel. 1. Sites Web de ASUS Les sites Web internationaux d’ASUS fournissent des informations mises à jour sur les produits matériels et logiciels d’ASUS. Référezvous à http://www.asus.com 2. Documentation en option Votre emballage produit peut inclure une documentation en option qui peut avoir été ajoutée par votre revendeur.
1.1 Bienvenu Merci d'avoir acheté un moniteur LCD d'ASUS® ! Le dernier moniteur à écran LCD large d’ASUS offre un affichage plus net, plus large et plus lumineux, en plus de toute une gamme de fonctions qui améliorent votre séance de visionnage. Avec ces fonctions du moniteur, vous pouvez profiter du confort et vous régaler d’une expérience visuelle ! 1.
1.3 Assemblage du moniteur Pour assembler le moniteur : • Lors de l'assemblage du bras/de la base du moniteur, nous vous conseillons de conserver le moniteur dans son emballage en polystyrène expansé (EPS). 1. Alignez le trou de vis sur le bras avec la vis fournie sur la base. Puis insérez la base dans le bras. 2. Fixez la base au bras en serrant la vis fournie. 3. Retirez le moniteur de son emballage EPS. Ajustez le moniteur pour que l'angle soit confortable.
1.4 Branchement des câbles 1.4.1 Arrière du moniteur LCD 9 DCIN 1 2 3 1. Port d’entrée CC 2. Port USB3.0 en amont 3. Port USB3.0 en aval 4. Port USB3.0 en aval 5. Port HDMI2.0 6. Port HDMI2.0 7. DisplayPort 8. Prise des écouteurs 9.
1.5 Présentation du moniteur 1.5.1 Utilisation des boutons de contrôle Utilisez les boutons de contrôle à l'arrière du moniteur pour régler les paramètres du moniteur. 6 6 5 5 4 4 3 3 2 2 1 1. Indicateur d’alimentation : • 2. État Description Blanc Marche Orange Mode Veille Arrêt Arrêt Bouton d'alimentation : • 3. Appuyez sur ce bouton pour allumer/éteindre le moniteur. Appuyez sur cette touche pour allumer le moniteur lorsque le moniteur est hors tension.
• Appuyez sur le bouton GamePlus pour accéder au menu principal GamePlus. • Activez la fonction Viseur, Minuterie, Compteur de FPS ou Alignement écran. • Déplacez le bouton et appuyez sur Appuyez sur • vers le haut/bas pour sélectionner pour confirmer la fonction souhaitée. pour sortir et quitter. Viseur/Minuterie/Compteur de FPS peut être déplacé en appuyant sur la touche 5 directions • . Vous devez désactiver HDR sur votre appareil si vous voulez activer le mode Tireur d'élite.
2.1 Réglage du moniteur • Pour une vision optimale, il est recommandé d’avoir une vision de face sur le moniteur, ensuite réglez l’angle du moniteur pour qu’il soit confortable. • Tenez le pied pour empêcher le moniteur de tomber quand vous le changez d’angle. • Vous pouvez ajuster l’angle du moniteur de -5˚ à 20˚ et le faire pivoter jusqu'à 25˚ vers la droite ou la gauche. Vous pouvez aussi ajuster la hauteur du moniteur à +/- 10 cm.
2.
2.3 Détacher le bras / support (pour support mural VESA) • Évitez d'endommager la surface du moniteur. En détachant le support du moniteur, conservez toujours le moniteur dans son emballage EPS. Le bras démontable de ce moniteur est conçu spécialement pour un montage mural VESA. Pour démonter le bras/le support 1. Débranchez les câbles d’alimentation et de signal. Mettez délicatement le moniteur face orientée vers le bas sur son emballage EPS. 2.
3.1 Menu OSD (Affichage à l’écran) 3.1.1 Comment faire pour reconfigurer DisplayPort 2560x1440@165Hz Mode Paysage Aura Off ROG Swift PG329Q HDR OFF Jeux Surcadençage Image OD Variable Couleur Adaptive-Sync Sélection Entrée ELMB/ELMB SYNC Config PIP/PBP GamePlus Effet d'éclairage GameVisual MyFavorite Shadow Boost Configuration Système MOVE/ENTER BACK EXIT 1. Appuyez sur le bouton central du bouton 5 directions pour afficher le menu OSD. 2.
3.1.2 1. Présentation des fonctions de l'OSD Jeux DisplayPort 2560x1440@165Hz Mode Paysage Aura Off ROG Swift PG329Q HDR OFF Jeux Surcadençage Image OD Variable Couleur Adaptive-Sync Sélection Entrée ELMB/ELMB SYNC Config PIP/PBP GamePlus Effet d'éclairage GameVisual MyFavorite Shadow Boost Configuration Système MOVE/ENTER BACK EXIT • Surcadençage : Cette fonction vous permet d’ajuster le taux de rafraîchissement en dp.
2. Image Vous pouvez modifier Luminosité, Contraste, HDR, VividPixel , Atténuation Dynamique, ASCR, Contrôle de l'aspect et Filtre de lumière bleue à partir de cette fonction principale.
• Lorsque Filtre de lumière bleue est activé, les paramètres par défaut de Mode course sont automatiquement importés. • Entre les niveau 1 et niveau 3, la fonction de luminosité est configurable par l'utilisateur. • Le niveau 4 est un paramètre optimisé. Il est conforme à la certification TUV pour la lumière bleue faible. La fonction de luminosité n'est pas configurable par l'utilisateur.
3. Couleur Choisissez la couleur d'image désirée avec cette fonction. DisplayPort 2560x1440@165Hz Mode Paysage Aura Off ROG Swift PG329Q HDR OFF Jeux Température Couleur Image Gamma Couleur Saturation Sélection Entrée Config PIP/PBP Effet d'éclairage MyFavorite Configuration Système • Température Couleur : Contient trois modes de couleurs prédéfinies (Froid, Normal, Chaud) et Mode Utilisateur. • Gamma : Contient trois modes de gamma dont 1.8, 2.2, 2.5.
5. Config PIP/PBP Les Paramètres PIP/PBP vous permettent d'ouvrir une/des sousfenêtre(s) connectée(s) depuis les sources vidéo.
6. Effet d'éclairage DisplayPort 2560x1440@165Hz Mode Paysage Aura Off ROG Swift PG329Q HDR OFF Jeux Aura Sync Image Aura RGB Couleur Sélection Entrée Config PIP/PBP Effet d'éclairage MyFavorite Configuration Système BACK MOVE/ENTER • Aura Sync : Permet d'activer ou de désactiver la fonction Aura Sync qui synchronise l'effet lumineux Aura RVB parmi tous les appareils pris en charge.
8. • Raccourci : L'utilisateur peut choisir entre "GamePlus, GameVisual, Mode Utilisateur, Luminosité, Contraste, Config PIP/ PBP, Sélection Entrée, HDR, Filtre de lumière bleue, Température Couleur, Volume, MyFavorite-1 (Load), MyFavorite-2 (Load)" et le définir comme touche de raccourci. • Régl. Personnalisé : Vous pouvez effectuer les réglages en fonction de vos préférences. Configuration Système Pour ajuster la configuration du système.
3-8 • USB Hub : Active/Désactive la fonction USB Hub pendant le mode veille. • Indicateur d’alimentation : Pour allumer/éteindre le voyant d’alimentation DEL. • Verr touche d'alim. : Pour activer/désactiver la touche d'alimentation • Serrure : Désactive le fonctionnement de toutes les touches. Appuyez sur le bouton bas pendant plus de cinq secondes pour désactiver la fonction de verrouillage des touches. • Configuration OSD : Pour ajuster le Délai OSD, DDC/CI, et la Transparence de l'écran OSD.
3.2 Spécifications Modèle PG329Q Taille du panneau 32"W (81,3 cm) Résolution max. 2560 x 1440@175Hz (surcadençage) Luminosité (Typ.) 400 nits (typ.), 600 nits (max.) Rapport de contraste intrinsèque (Typ.) 1000:1 Angle de vue (CR>10) 178°(V) /178°(H) Couleurs de l’écran 1,07B Temps de réponse 1 ms (G à G ) Son de HDMI Oui Entrée HDMI HDMI2.0 x 2 Entrée DisplayPort Oui PBP Port USB3.
3.3 Guide de dépannage (FAQ) Problème Le voyant DEL d’alimentation n’est pas MARCHE Le voyant DEL d’alimentation est de couleur orange et il n’y a aucune image sur l’écran L’image de l’écran est trop claire ou trop foncée L'image de l'écran n'est pas centrée ou pas de bonne taille Les couleurs de l’image de l’écran sont bizarres (le blanc n’apparaît pas blanc) Aucun son ou le son est très faible 3-10 Solution possible • Appuyez sur le bouton pour vérifier si le moniteur est en mode Marche.
3.
synchronization vidéo synchronization vidéo 2560 3840 1440 2160 175 59,94/60 O O O * Les modes qui ne sont pas listés dans ces tableaux peuvent ne pas être supportés. Pour une résolution optimale, nous vous conseillons de choisir un mode listé dans les tableaux ci-dessus.