目錄 注意事項 ....................................................................................................... iii 安全資訊 ....................................................................................................... iv 維護與清潔 .................................................................................................... vi 1.1 歡迎使用 ......................................................................................... 1-1 1.2 包裝內容 ...........................................................
注意事項 聯邦通訊委員會 (FCC) 聲明 本裝置符合 FCC 條款第 15 部份的規定。操作程序受限於下列兩項條件: • 本裝置不會造成有害干擾。 • 本裝置須能承受任何可接收的干擾,包括可能導致意外操作的干擾。 本設備經測試符合 FCC 條款第 15 部份關於 B 類數位裝置的規定。這些限 制之主要目的乃針對在住宅區內安裝裝置時,提供有害干擾的合理保護。本 設備會產生、使用並放射無線射頻能量,如未根據製造商的指示方法安裝和 使用本設備,可能會對無線電通訊造成有害干擾。然而,我們無法保證在特 定環境下安裝此設備不會造成任何干擾。若本設備確實對無線電或電視接收 造成不良干擾(請開關設備加以確認),您可採取以下方式改善干擾情形: • 重新調整收訊天線的方向或位置。 • 將設備與接收器之間的距離加大。 • 將設備與接收器插至使用不同電路的電源插座。 • 向有經驗的無線電 電視技術人員尋求協助。 連接螢幕與顯示卡需使用屏蔽纜線以確保遵循 FCC 規範。未經負 責遵循方明確核准變更或修改本機可能造成使用者操作本設備的權 限失效。 加拿大通訊部聲明 根據加拿大通訊部於無線電干擾法規中針對數位裝置
安全資訊 • 安裝本顯示器之前,請詳閱產品包裝內的說明文件。 • 為避免起火或觸電,請勿將顯示器暴露於下雨或潮濕的環境中。 • 切勿嘗試打開顯示器機殼。顯示器內的高壓電可能會造成嚴重的人身傷 害。 • 若電源中斷,切勿嘗試自行修復。請洽詢合格維修技術人員或經銷商。 • 使用本產品前,請務必正確連接所有纜線,並確認電源線並未損壞。若 發現任何損壞情形,請立即洽詢經銷商。 • 機殼背面或頂端的狹槽和開口為通風孔;請勿堵塞這些狹槽。除非通風 良好,否則切勿將本產品放至於散熱器或熱源附近或上方。 • 本顯示器只能使用標籤上註明的電源類型運作。若您不確定府上的電源 類型,請洽詢經銷商或當地的電力公司。 • 請使用符合當地電源標準的電源插頭。 • 請勿讓排插和延長線過載。電源過載可能會引發火災或造成觸電。 • 請避開多塵、潮濕和溫度過高 過低的環境。請勿將顯示器放置於任何 可能潮濕之處。請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本裝置的插頭,避免顯示器因電源 突波而造成損壞。 • 切勿將任何異物塞入顯示器機殼開口內,也不可讓液體潑灑流入。 • 為確
有害物質限制聲明(印度) 本產品遵守「2016 印度電子廢棄物 ( 管理 ) 規定」並除本規定表 2 列出之 免除項目外,禁止在均勻材質重量中使用濃度超過 0.1% 的鉛、汞、六價鉻、 多溴聯苯 (PBBs) 和多溴二苯醚 (PBDEs),以及在均勻材質重量中使用濃度 超過 0.01% 的鎘。 中國製 限用物質及其化學符號 單元 鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 (Cr+6) 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) 塑料外框 ○ ○ ○ ○ ○ ○ 後殼 ○ ○ ○ ○ ○ ○ 液晶面板 - ○ ○ ○ ○ ○ 電路板組件 - ○ ○ ○ ○ ○ 底座 ○ ○ ○ ○ ○ ○ 電源線 - ○ ○ ○ ○ ○ 其他線材 - ○ ○ ○ ○ ○ 喇叭(選配) - ○ ○ ○ ○ ○ 風扇(選配) - ○ ○ ○ ○ ○ 備考 1.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。 備考 2.
維護與清潔 • 抬起顯示器或變更顯示器位置前,請先拔下纜線和電源線。放置顯示器 時,請依照正確的方式抬起顯示器。抬起或移動顯示器時,請抓住顯示 器的邊緣;切勿只抓住底座或電源線。 • 清潔:請關閉顯示器電源並拔下電源線。使用不會造成刮傷的軟布清潔 顯示器表面,並以軟布沾少許中性清潔劑清除頑垢。 • 避免使用含酒精或丙酮的清潔劑。請使用液晶顯示器專用的清潔劑。切 勿將清潔劑直接噴灑在螢幕上,以免滲入顯示器內並引起觸電。 此垃圾桶畫叉符號代表該產品 ( 電氣、電子設備及內含水銀鈕釦電 池 ) 不得投入一般廢棄物中。請查閱當地電子產品棄置法規。 AEEE yönetmeliğine uygundur 以下徵狀為顯示器正常現象: • 第一次使用本顯示器時,螢幕可能會因螢光燈的自然特性而出現閃爍的 情形。請關閉電源並重新開啟,即可讓閃爍情況消失。 • 不同的桌面圖案可能會造成螢幕出現輕微亮度不均的情況。 • 顯示同樣的影像數小時後,當您切換影像時,可能會出現原有影像的殘 影。螢幕畫面會慢慢恢復正常,關閉電源開關數小時也可以改善此情 況。 • 螢幕變黑、閃爍或無法運作時,請交由經銷商或維修中心處
更多詳細資訊 如需其他資訊以及產品 軟體更新,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供關於 ASUS 硬體和軟體產品的最新資訊。請參閱 http://www.asus.com 2.
1.1 歡迎使用 感謝您購買 ASUS® 液晶顯示器! ASUS 最新的寬螢幕液晶顯示器提供更清晰、更寬廣、更鮮明的畫面顯示, 以及許多增強觀賞體驗的功能。 透過這些功能,您可以盡情享受本顯示器所帶來的便利性及愉快的視覺體 驗! 1.2 包裝內容 請檢查包裝內是否包含下列物品: 液晶顯示器 顯示器底座 快速使用指南 保固卡 1 x 電源線 1 x HDMI 纜線 1 x DP 纜線 1 x 整流器 1 x USB 3.
1.3 調整顯示器 組裝顯示器的方法如下: • 在組裝顯示器支架/底座時,建議您保留顯示器內部的 EPS (膨脹性聚苯 乙烯) 包裝。 1. 對準顯示器支架上的螺絲孔和底座上的隨附螺絲。然後將底座插入顯 示器支架中。 2. 鎖緊隨附螺絲以固定顯示器支架上的底座。 3. 將顯示器底座上的三角記號對準 LED 投影蓋。然後將 LED 投影蓋蓋 上顯示器底座。 4. 從顯示器的 EPS 包裝中取出顯示器。將顯示器調整至最適合的觀看角 度。 2 1 3 5.
1.
1.5 連接纜線 1.5.1 液晶顯示器背面 7 1 1-4 1. DisplayPort 2. HDMI1.4 連接埠 3. 耳機插孔 4. USB 上行連接埠 5. USB 下行連接埠 6. DC-IN 連接埠 7.
1.6 顯示器簡介 1.6.1 使用控制鈕 使用顯示器背面的控制鈕來調整顯示器設定。 6 6 5 5 4 4 3 3 2 1 1. 電源指示燈: • 2. 電源指示燈的顏色定義如下表所示。 狀態 說明 白色 開 閃爍琥珀色 進入待機模式 琥珀色 待機模式/無訊號 關 關 紅色 G-SYNC 電源按鈕: • 按下此按鈕可開啟 • 按下此快速鍵切換六種採用 GameVisual™ 智慧型影像技術的預 設影像顯示模式 (風景模式、比賽模式、電影模式、RTS/RPG模 式、FPS模式及 sRGB模式)。 • GamePlus:GamePlus 功能含有工具套件,可在玩不同類型的遊 戲時,為使用者建立更出色的遊戲環境。尤其,十字瞄準線功能是 特別為了對第一人稱射擊(FPS)遊戲感興趣的新玩家或新手而設 計的。 3. 關閉顯示器電源。 GameVisual: 4.
• 選擇 GamePlus 按鈕,以進入 GamePlus 主選單。 • 啟動Crosshair (十字瞄準線) 、Timer (定時器)或 FPS Counter (FPS 計數器)功能 • 向上 向下移動 ( ) 按鈕以選擇並按下 功能。按壓 即可關閉,然後離開。 • 按下 5 向鍵可移動啟動Crosshair (十字瞄準線) /Timer (定時 器)/FPS Counter (FPS 計數器)。 GamePlus 主選單 ( ) 確認所需 GamePlus Crosshair ( 十字瞄準線 ) GamePlus NEXT GamePlus Timer ( 定時器 ) GamePlus BACK/EXIT NEXT BACK/EXIT GamePlus FPS Counter (FPS 計數器 ) GamePlus FPS NEXT 5. 關閉按鈕 • 6.
2.
2.
2.3 拆卸支架 底座(適用於 VESA 壁掛式安裝) • 避免破壞顯示器表面。拆卸顯示器底座時,請務必保留顯示器內部的 EPS 包裝。 本顯示器的可拆式底座是特別針對 VESA 壁掛式安裝所設計。 拆卸支架 底座 1. 拔下電源線和訊號線。小心讓顯示器正面朝下並放入 EPS 包裝。 2. 拆下顯示器與支架專用的外蓋。 3. 拆下固定支架至顯示器背面的四 (4) 支螺絲。 4. 自顯示器拆下底座(支架及底座)。 • VESA 壁掛工具組 (100 x 100 mm) 為選購配件。 • 僅限使用 UL 所列重量/負載 28.
3.1 OSD(螢幕功能顯示)選單 3.1.1 如何重新設定 標準模式 DisplayPort 3440x1440@ 60Hz 比賽模式 Aura 靜態 ROG Swift PG349Q Over Clocking 開 濾藍光 色彩 影像 輸入選擇 系統設定 移動/確定 返回 離開 1. 按下中央 5 向按鈕以顯示 OSD 選單。 2. 按下向上與向下鍵可切換選單中的選項。 在圖示間移動時,選項名稱 會反白顯示。 3. 若要選擇選單中的反白項目,請按下右鍵或中央按鈕。 4. 按下向上及向下鍵可選擇所需的參數。 5. 按下向右鍵或中央按鈕可進入滑動桿,然後使用向上或向下鍵(視選 單中的指標而定)進行變更。 6.
3.1.2 1.
2.
3. 色彩 請利用此功能選取您喜歡的影像色彩。 標準模式 DisplayPort 3440x1440@ 60Hz 比賽模式 Aura 靜態 ROG Swift PG349Q Over Clocking 亮度 80 濾藍光 對比 50 色彩 彩度 50 影像 色溫 輸入選擇 Gamma 系統設定 移動/確定 離開 • 亮度:調整範圍從 0 到 100。 • 對比:調整範圍從 0 到 100。 • 彩度:調整範圍從 0 到 100。 • 色溫:包含三種預設色彩模式(冷色溫、正常、暖色溫), 以及使用者模式。 • Gamma:包含三種含 1.8、2.2、2.
4.
5.
6.
• 3-8 Aura RGB:您可在此功能中選擇顯示器的 Aura RGB 照明效果和 變更照明效果設定。若您要關閉 Aura RGB 照明效果,請選擇「 關」。 • 若 Aura Sync 功能開啟,Aura RGB 功能將無法使用。 • 如需自訂您電腦 Aura 照明效果方式的資訊,請參閱第 3-9 頁。 • 聲音:選擇「音量」以調整輸出音量。選擇「靜音」以靜音輸出音 量。 • 恢復出廠模式:選擇「是」會將所有設定值回復至出廠預設模式。 • DisplayPort深度休眠:選擇DisplayPort深度休眠。 • HDMI深度休眠:選擇HDMI深度休眠。 第 3 章:一般指示
3.2 Aura AURA 是一種控制支援裝置上各色 LED 的軟體程式,如顯示器、主機板、 顯示卡、桌上型電腦等。您可利用 Aura 調整這些裝置 RGB LED 色彩及選 擇不同的照明效果。您也可透過校正來修正或調整 LED 色彩。 若要啟動 Aura: 1. 開啟 OSD 選單中的 Aura Sync 功能。 2. 連接顯示器 USB 3.0 上行連接埠至電腦的 USB 連接埠。 3. 安裝 AURA 然後重新啟動電腦。 4.
4 按一下以復原變更。 5 按一下以套用變更。 若顯示器與電腦間的 USB 上行連線中斷連接,如要恢復 Aura 功 能,您需重新連接顯示器 USB 3.
3.3 規格 機型 螢幕尺寸 最大解析度 亮度(一般) 固有對比度(一般) 視角 (CR>10) PG349Q 34.14 in. (86.72 cm) (長寬比 21:9) 3440x1440 300cd/m2 1000:1 178°(垂直) 178°(水平) 顯示色彩 16.7M 反應時間 4ms (G 至 G ) HDMI 音效 是 HDMI 輸入 HDMI1.4x1 DisplayPort 輸入 是 USB3.0 連接埠 上行 x1,下行 x2 (上行無連結時,代表 USB 連接埠無充電器) 耳機 開機耗電量 是 <85 W*(在無音訊 / USB / 讀卡機連線時測量 200 nits 畫面亮度) 機殼顏色 黑色 省電模式 < 0.5W 電源關閉模式 < 0.5W 傾斜角度 -5° ~ +20° 實體尺寸含底座(寬x高x深) 815.85 x 560.22x 307.35 mm 實體尺寸不含底座(寬x高x深) 815.85 x 560.22x128.
3.
3.
視訊時序 時序清單 HDMI DisplayPort 640x480P @ 59.94Hz V X 640x480P @ 60Hz V X 720x480P @ 59.94Hz V X 720x480P @ 60Hz V X 720x576P @ 50Hz V X 1280x720P @ 50Hz V X 1280x720P @ 59.94Hz V X 1280x720P @ 60Hz V X 1920x1080P @ 50Hz V X 1920x1080P @ 59.