第一版 2019 年 7 月 版權所有 © 2019 ASUSTeK COMPUTER INC. 保留所有權利。 在未取得 ASUSTeK COMPUTER INC.
目錄 注意事項 ....................................................................................................... iv 安全資訊 ........................................................................................................ v 保養和清潔 .................................................................................................... vi Takeback Services..................................................................................... vii 第 1 章: 產品介紹 1.1 歡迎使用! ..........................................
注意事項 聯邦通訊委員會聲明 本裝置符合 FCC 規定之第 15 篇。 操作符合下列兩個條件: • 本裝置不會造成有害干擾,而且 • 本裝置會接受任何接收到的干擾,包括可能會影響裝置運作的干擾。 本設備通過測試並符合 FCC 規定之第 15 篇 B 級數位裝置的限制。 這些限制的用意 在於提供適當防護,避免設備安裝在居住環境下產生有害干擾。 本設備會產生、使 用和發射無線電頻能量,此外,若未依照指示安裝和使用,可能會對無線電通訊產 生不良干擾。 然而,並不保證在特定安裝情況下不會產生干擾。 若本設備對收音機 或電視機的收訊產生不良干擾(可開啟然後關閉設備電源判定),使用者可透過以 下方法消除干擾: • 重新調整接收天線的方向或位置。 • 增加設備和接收天線之間的距離。 • 將本設備連接到與接收器電源不同的電源插座上。 • 請向經銷商或有經驗的廣電技術人員尋求協助。 連接顯示器與顯示卡的遮蔽纜線,須符合 FCC 的規定。 若未經相容性規定之相 關當局明示許可,擅自修改或改裝本裝置,使用者可能喪失操作本設備之權限。 加拿大通訊部聲明 本數位裝置未超過加拿大通訊部無線電干擾法規所規定之數位裝
安全資訊 • 設定本顯示器之前,請詳讀產品包裝內的說明文件。 • 為預防起火或觸電,請勿將顯示器置於雨中或潮溼環境中。 • 請勿試圖打開顯示器的機殼。顯示器內部的高壓電可能造成人員嚴重受傷。 • 若電源供應器損壞,請勿嘗試自行修復。請洽詢合格的維修技術人員您的零售 商。 • 使用本產品前,請確定已正確連接所有纜線,而且電源線並未損壞。若發現任何 損壞,請立刻聯絡您的經銷商。 • 機殼背面或頂端的開口和通風口係用於散熱。請勿堵塞這些開口。除非通風良 好,否則請勿將本產品置於靠近散熱器或熱源的位置或其上方。 • 本顯示器只能在產品標籤所示的電源環境下操作。若您不確定您家中的電源規 格,請洽詢您的經銷商或當地的電力公司。 • 使用符合當地電源標準的電源插頭。 • 不可使排插和延長線的電源過載。 電源過載會導致起火或人員觸電。 • 避免在多灰塵、潮溼和極端溫度的環境中使用。請勿將顯示器置於可能會使其受 潮的區域。請將顯示器置於平穩的表面上。 • 雷雨期間或長時間不使用時,請拔下本機的電源插頭。如此可預防顯示器因電源 突波而損壞。 • 請勿讓任何物體或液體進入顯示器機殼的開
保養和清潔 • 抬高或重新移位顯示器之前,請先拔下纜線和電源線。顯示器移位前,請依照正 確的抬高方法。抬高或移動顯示器時,請握住顯示器的邊緣。請勿以拉抬底座或 纜線的方式抬高顯示器。 • 清潔。關閉顯示器的電源,然後拔下電源線。使用無毛球且不會刮傷螢幕的布清 潔顯示器表面。可用沾有中性清潔劑的布清除頑垢。 • 避免使用含有酒精或丙酮的清潔劑。使用顯示器專用的清潔劑。請勿直接將清潔 劑噴灑於螢幕上,否則可能滲入顯示器內並造成人員觸電。 若顯示器發生以下情況,屬於正常現象: • 由於螢光燈的特性,初次使用螢幕時,畫面可能會閃爍。請關閉電源開關,然後 再重新開啟,確定閃爍現象消失。 • 不同的桌面模式可能導致螢幕有輕微亮度不均的情況。 • 顯示同一幅影像數小時後,切換影像時可能會出現前張影像的殘影。殘影會慢慢 消失,或者您可以開關電源數小時消除此情況。 • 螢幕變黑、閃爍或完全無法運作時,請洽詢您的經銷商或服務中心進行修復。 請勿自行修理螢幕! 本手冊使用的慣語 警告:執行作業時,避免人員受傷的資訊。 注意:執行作業時,避免零組件損壞的資訊。 重要:執行作業時「必須」遵守的資訊。 附註:
其它詳細資訊來源 如需其它資訊和產品與軟體的更新程式,請參閱下列來源。 1. ASUS 網站 ASUS 全球網站提供有關 ASUS 硬體和軟體產品的最新資訊。請連至 http://www.asus.com 取得相關資訊。 2. 選用的說明文件 您的產品包裝內可能有經銷商所提供的選用說明文件。產品的標準包裝中不含 此類文件。 Takeback Services ASUS recycling and takeback programs come from our commitment to the highest standards for protecting our environment. We believe in providing solutions for our customers to be able to responsibly recycle our products, batteries and other components as well as the packaging materials. Please go to http://csr.asus.
viii
1.1 歡迎使用! 感謝您購買 ROG 遊戲顯示器! ASUS 最新的寬螢幕液晶顯示器提供更寬廣、更明亮和更清晰的顯示,以及許多可 增強觀看感受的功能。 您可藉由這些功能享受到本顯示器帶給您的便利與快樂的視覺體驗! 1.
1.3 顯示器介紹 1.3.1 正面圖 1 2 3 4 5 6 1. 5向( ) 按鈕 • 開啟 OSD 功能表。 啟動所選的 OSD 功能表項目。 • 增加/減少值或向上/向下/向左/向右移動選擇。 • 顯示器進入待機模式時,開啟 OSD 功能表。 2. 快速鍵 1 • 輸入選擇快速鍵。 • 顯示器進入待機模式時,開啟 OSD 功能表。 3. 快速鍵 2 • 亮度快速鍵。 • 顯示器進入待機模式時,開啟 OSD 功能表。 4. 關閉按鈕 • 離開 OSD 功能表項目。 • 長按 5 秒即可開啟和關閉按鍵鎖功能。 5.
6. 電源指示燈 • 電源指示燈的顏色定義如下表所示。 1.3.2 狀態 說明 白色 開 琥珀色閃爍 正在進入待機模式 琥珀色 待機模式/無信號輸入 關 關 紅色 綠色 G-SYNC HDR 背面圖 11 1 2 3 4 5 6 7 8 9 10 1. S/PDIF 輸出連接埠。此連接埠用於輸出音訊 S/PDIF 訊號。 2. HDMI 連接埠。這些連接埠用於連接 HDMI 相容裝置。 3. DisplayPort。此連接埠用於連接 DisplayPort 相容裝置。 4. USB 3.0 資料上傳連接埠。此連接埠用於連接 USB 上傳資料線。此連接線可 啟用顯示器上的 USB 連接埠。 5. USB 3.0 資料下載連接埠。這些連接埠用於連接 USB 鍵盤 / 滑鼠、USB 隨身 碟等 USB 裝置。 6. 僅限 Aura Sync ROG 標誌投射燈使用。 7. 僅限維修人員使用。 8. AC IN 連接埠。此連接埠用於連接電源線。 9. 電源開關。按下開關以開啟/關閉電源。 10.
1.3.3 遙控器 1 3 2 ENTER 4 5 8 1. 6 7 電源按鈕 • 開啟/關閉顯示器電源。 2. 輸入選擇按鈕: • 選擇可用的輸入來源。 將 DisplayPort/HDMI 訊號線連接到顯示器之後,按下 按鈕(輸入選擇按 鈕)可顯示 DisplayPort、HDMI-1、HDMI-2、HDMI-3、HDMI-4 訊號。 3. 方向箭頭按鈕 • 開啟 OSD 主功能表。 • 增加/減少值或向上/向下/向左/向右移動選擇。 4.
5. 關閉按鈕 • 離開 OSD 功能表項目。 • 長按 5 秒即可開啟和關閉按鍵鎖功能。 6. 捷徑按鈕 1 • 預設值: 亮度。 • 顯示器進入待機模式時,開啟 OSD 功能表。 • 若要變更捷徑功能,請進入系統設定 > 遙控器的捷徑功能表。 7. 捷徑按鈕 2 • 預設值: 亮度。 • 顯示器進入待機模式時,開啟 OSD 功能表。 • 若要變更捷徑功能,請進入系統設定 > 遙控器的捷徑功能表。 8. 音量按鈕 • 降低或提高音量。 1.3.
1-6 第 1 章: 產品介紹
2.1 拆開底座(適用於 VESA 壁掛式安裝) 本螢幕的可拆式底座專為 VESA 壁掛架所設計。 拆卸底座: 1. 將顯示器正面朝下置於桌上。 2. 使用內六角扳手鬆開顯示器後端的 4 顆螺絲,然後取下底座。 建議您使用軟布覆蓋桌子表面,避免顯示器受損。 2.
2.3 安裝 Aura Sync ROG 標誌投射燈 將 Aura Sync ROG 標誌投射燈鎖上顯示器後端,並且將另一端連接到顯示器的 mini-USB 連接埠。 3 2.4 2 1 接線 依下列指示連接訊號線: 僅供維修之用 2-2 • 連接電源線:將電源線的一端牢牢連接到顯示器的 AC 輸入埠,將另一端連接到 電源插座。 • 連接 DisplayPort/HDMI 訊號線: a. 將 DisplayPort/HDMI 訊號線的一端連接到顯示器的 DisplayPort/HDMI 連 接埠。 b.
• 使用 USB 3.0 連接埠:取得 USB 3.0 訊號線,將 USB 上傳資料線較小的一端 (B 型)插入顯示器的 USB 資料上傳連接埠,並將較大的一端(A 型)插入 電腦的 USB 3.0 連接埠。請確保電腦已安裝最新版 Windows 7/Windows 8.1/ Windows 10 作業系統。連接完成後即可讓顯示器的 USB 連接埠開始運作。 2.
2-4 第 2 章: 設定
3.1 OSD(螢幕功能顯示)功能表 3.1.1 如何重新設定 風景模式 GameVisual 刷新率 60 Hz HDMI-1 輸入選擇 Aura RGB 關 Over Clocking Over Clocking 最大刷新率 聲音 色彩 影像 輸入選擇 系統設定 ENTER BACK EXIT 1. 按下顯示器的 5 向 ( 功能表。 ) 按鈕或遙控器的方向箭頭按鈕/ENTER 按鈕啟動 OSD 2. 向上/向下/向左/向右移動 5 向 ( ) 按鈕或按下 / / / 按鈕瀏覽功能。 將所需的功能反白,並按下 5 向 ( ) 按鈕或 ENTER 按鈕啟動該功能。如果 選擇的功能有子功能表,請再次向上/向下/向左/向右移動 5 向 ( ) 按鈕,或 按下 / / / 按鈕瀏覽子功能表功能。 將所需的子功能表功能反白,並 按下 5 向 ( ) 按鈕或 ENTER 按鈕啟動該功能。 3. 向上/向下/向左/向右移動 5 向 ( 能的設定。 4.
3.1.2 1. OSD 功能介紹 Over Clocking 此功能可讓您調整刷新率。 刷新率 60 Hz HDMI-1 輸入選擇 風景模式 GameVisual Aura RGB 關 Over Clocking Over Clocking 最大刷新率 聲音 色彩 影像 輸入選擇 系統設定 ENTER • 2.
• 音訊輸出:可供您設定音訊輸出路徑為內建喇叭或 SPDIF。 選擇 SPDIF 時,無法使用音量和 AudioWizard。 • 3. AudioWizard:包含 3 個音訊模式,包括遊戲模式、電影模式和關閉模 式。 色彩 您可以在此選單中設定色彩相關設定。 風景模式 GameVisual 刷新率 60 Hz HDMI-1 輸入選擇 Aura RGB 關 色彩 Over Clocking 聲音 色彩 亮度 90 基準白光 (尼特) 對比 50 色溫 Gamma 影像 輸入選擇 系統設定 ENTER BACK EXIT • 亮度:調整範圍介於 0 到 100。 HDR 啟用時,亮度將變更為白色峰值 (nits) 1000,而且無法變更。 • 基準白光(尼特):僅顯示範圍。 • 對比:調整範圍介於 0 到 100。 • 色溫:包含冷色溫、正常、暖色溫和使用者模式等 4 種模式。 • Gamma:可讓您將色彩模式設為 1.8、2.0、2.2、2.4 或 2.
4.
使用者可透過以下來減輕眼睛疲勞: • 長時間使用電腦者建議連續工作 1 小時後進行短暫休息 (至少 5 分鐘)。 短暫頻繁的休息比單次長時間休息更有效。 • 使用者可透過經常性的專注遠方物體,來減少眼睛疲勞和眼睛乾燥。 • 經常性反覆的眼球運動也可以幫助減輕使用者的眼睛疲勞。如果持續眼睛疲 勞,請就醫。眼球運動:(1) 眼球重複上下移動 (2) 慢慢轉動眼球 (3) 對角 線式移動眼球。如果眼睛疲勞仍然持續,請諮詢醫生。 • 高能量的藍光可能會造成眼睛疲勞與老年性黃斑部病變。濾藍光功能可以減 少最高 70% 來自螢幕的藍光能量,避免電腦視覺症候群的症狀發生。 • 暗場增益:深色強化可調整螢幕的 Gamma 曲線來強調影像的深色,使深 色場景和物體更顯眼。 • 動態背光:啟用或停用動態背光的操作。選項有快(適合遊戲)、中和緩 (適合商業或文書處理)。 功能啟用時,可能會發現暗色背景出現輕微的光暈效果。 這是正常現象,並非 故障。 5.
6. 系統設定 可讓您調整系統。 風景模式 GameVisual 刷新率 60 Hz HDMI-1 輸入選擇 Aura RGB 關 系統設定 Over Clocking 語言 聲音 Aura Sync Aura RGB 色彩 GamePlus 影像 透明度 選單時間 輸入選擇 按鍵鎖 系統設定 ENTER BACK EXIT • 語言:有 9 種語言可以選擇,包括英文、法文、土耳其文、簡體中文、繁 體中文、日文、韓文、波斯文、阿拉伯文。 • Aura Sync:可讓您開啟或關閉 Aura Sync 功能,該功能可在所有支援的 裝置上同步 Aura RGB 燈光效果。 • Aura RGB:在此功能中,您可以選取顯示器的 Aura RGB 燈光效果,並 變更燈光效果的設定。如果要關閉 Aura RGB 燈光效果,請選取「關」。 • • 如果 Aura Sync 功能開啟,將無法使用 Aura RGB 功能。 • 如需如何從電腦自訂 Aura 燈光效果的資訊,請參閱 3.
GamePlus — 定時器 GamePlus — FPS 計數器 GamePlus 定時器 GamePlus FPS 計數器 30:00 刷新率 40:00 FPS 計數器 50:00 60:00 90:00 • 透明度:將 OSD 背景從不透明調整至透明。 • 選單時間:調整選單時間,範圍介於 10 至 120 秒。 • 按鍵鎖:停用所有功能鍵。 按下 • 顯示資訊:顯示顯示器的資訊。 • DisplayPort 深度休眠:使 DisplayPort 連接埠進入深度休眠。 • HDMI 深度休眠:使 HDMI 連接埠進入深度休眠。 5 秒以上,即可取消按鍵鎖功能。 顯示器在進入深度休眠後若無法喚醒,請執行下列其中一個動作: - 按下顯示器上的任何按鈕(電源按鈕除外)來喚醒。 - 停用深度休眠功能。 (建議) • ECO Mode:降低耗電量。 ECO Mode 以降低影像畫質的方式大幅減少耗電量。關閉此模式可達到最佳影像 畫質(建議)。 • 自動 SDR 亮度:使亮度與環境光源變化同步。 由於 HDR10 是絕對標準,其中的內容定義絕對尼特等級,因此不建
3.2 ASUS Aura AURA 是一款對於支援的裝置本身的彩色 LED 進行控制的軟體程式,例如顯示器、 主機板、顯示卡、桌上型電腦等等。Aura 可讓您調整這些裝置的 RGB LED 色彩, 並選取不同的燈光效果。您也可以透過校正來修正或調整 LED 的色彩。 若要啟動 Aura: 1. 開啟 OSD 功能表中的 Aura Sync 功能。 2. 將顯示器的 USB 3.0 上傳連接埠連接到電腦的 USB 連接埠。 3. 安裝 AURA 並重新啟動電腦。 4. 按兩下桌面的 AURA 程式圖示 。 如需 AURA 程式功能的資訊,請參閱下圖。 調整 AURA 燈光選項 選取系統啟動時所需的 AURA 燈光效果 按一下可啟用預設 設定 按一下可套用 變更 按一下可復原變更 3-8 • 如果顯示器與電腦之間的 USB 上傳連線中斷,若要恢復 Aura 功能,您需要 將顯示器的 USB 3.0 上傳連接埠重新連接到電腦,然後重新啟動電腦。 • 如需詳細資訊,請造訪 https://www.asus.
3.3 規格總覽 面板類型 TFT LCD 面板大小 65 吋(16:9、64.53 吋)寬螢幕 最大解析度 3840 x 2160 畫素間距 0.372 x 0.372 mm 亮度(一般) 1000 cd/m2(峰值 /HDR 開啟) 對比比例(一般) 4000:1 視角(水平 / 垂直)CR > 10 178˚/178˚ 顯示色彩 16.7 M 回應時間 4 毫秒(灰階對灰階) 色溫選項 4 種色溫 類比輸入 無 數位輸入 DisplayPort v1.4 x 1、HDMI v2.0 x 4 SPDIF 輸出 有 音訊輸入 無 喇叭(內建) 有 USB 3.0 連接埠 資料上傳連接埠 x 1、資料下載連接埠 x 2 顏色 黑 電源 LED 白色(開機)/ 琥珀色(待機)/ 紅色 (G-Sync)/ 綠 色 (HDR) 傾角 無 旋轉 無 高度調整 無 VESA 壁掛式安裝 400 x 400 mm Kensington 鎖 有 電壓 AC: 8.
配件 快速使用指南、保固卡、遙控器、電源線、DP 訊 號線、HDMI 訊號線、USB 訊號線、Aura Sync ROG 標誌投射燈、纜線管理掛勾、內六角扳手、 校準報告 規範和標準 UL/cUL、CB、CE、ErP、FCC、CCC、BSMI、 CU、C-Tick、VCCI、PSE、CEL Level 3、 J-MOSS、RoHS、WEEE、Windows 7 和 8.
ASUS PG65UQ Outline Dimension *Unit:mm(inch) 3.00 [0.12] 714.24 [28.12] 10.90 [0.43] 87.20 [3.43] 389.82 [15.35] 400.00 [15.75] M6*4-Depth 15 Wall mount Keep out area 400.00 [15.75] 3-11 ROG Swift PG65U 系列電競顯示器 3.00 [0.12] 148.10 [5.83] 316.73 [12.47] 3.00 [0.12] AA-CENTER 11.90 [0.47] 1448.08 [57.01] 1428.48 [56.24] -Active Area 74.71 [2.94] 1100.84 [43.34] 803.52 [31.63] -Active Area 826.72 [32.55] 863.83 [34.01] 946.90 [37.28] 120.18 [4.73] 386.94 [15.23] 外型尺寸 3.4 401.76 [15.
3.
3.
DisplayPort 輸入 -- 超頻 解析度頻率 刷新率 3840 x 2160 144Hz 附註: 不支援交錯。 由於 HDR 內容是針對 4K (3840 x 2160) 解析度,因此其它解析度可能會導致影像異常。 請等候 Over Clocking 功能啟動。過程可能需要不到 40 秒。 Over Clocking 支援的 GPU:GTX1070、GTX1080 和 GTX1080 Ti 以上的 NVIDIA Pascal GPU 顯示卡。 關於其它 GPU,請洽詢製造商以了解是否相容。 此顯示器支援 NVIDIA G-SYNC 技術及針對 NVIDIA 圖形解決方案。 請注意,Over Clocking 功能/效能取決於 GPU、顯示的內容、檢視距離/角度、 刷新率和使用者眼睛敏感度。ASUS 僅提供此功能。不保證啟動後產生的效能或 任何副作用。對比度不足或條紋等現象並非產品瑕疵,而是無法避免的現象。 3-14 第 3 章: 一般指示
ROG Swift PG65U 系列電競顯示器 3-15
3-16 第 3 章: 一般指示