RS500A-E11 系列 RS500A-E11-RS4U RS500A-E11-RS12U 服務器 用戶手冊
C18559 1.00 版 2021 年 8 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
目錄 使用注意事項................................................................................................................................ vi 用電安全........................................................................................................................................ vii 電磁安全............................................................................................................................. vii 靜電元件........................................................................................
目錄 2.6 2.7 2.8 2.9 2.5.4 安裝 M.2 擴展卡............................................................................................2-22 2.5.5 安裝 OCP 3.0 卡...........................................................................................2-24 2.5.6 設置擴展卡.......................................................................................................2-25 連接排線...........................................................................................................................
目錄 5.3 主菜單(Main).............................................................................................................. 5-9 5.3.1 System Language [English]......................................................................... 5-9 5.3.2 System Date [Day xx/xx/xxxx].............................................................. 5-9 5.3.3 System Time [xx:xx:xx]............................................................................... 5-9 5.4 性能調整菜單(Performance Tuning menu)........................
使用注意事項 操作服務器之前請務必詳閱以下注意事項,避免因人為的疏失造成系統損傷甚至人 體本身的安全。 請勿使用非本產品配備的電源線,由於電路設計之不同,將有可能造成 內部零件的損壞。 ‧ 使用前,請檢查每一條連接線是否都已經依照用戶手冊指示連接妥當,以及電源 線是否有任何破損,或是連接不正確的情形發生。如有任何破損情形,請儘速與 您的授權經銷商聯絡,更換良好的線路。 ‧ 服務器安放的位置請遠離灰塵過多,溫度過高,太陽直射的地方。 ‧ 保持機器在乾燥的環境下使用,雨水、溼氣、液體等含有礦物質將會腐蝕電子線 路。 ‧ 使用服務器時,務必保持周遭散熱空間,以利散熱。 ‧ 使用前,請檢查各項外圍設備是否都已經連接妥當再啟動。 ‧ 避免邊吃東西邊使用服務器,以免污染機件造成故障。 ‧ 請避免讓紙張碎片、螺絲及線頭等小東西靠近服務器之連接器、插槽、孔位等 處,避免短路及接觸不良等情況發生。 ‧ 請勿將任何物品塞入服務器機件內,以避免引起機件短路,或是電路損毀。 ‧ 服務器啟動一段時間之後,散熱片及部份IC表面可能會發熱、發燙,請勿用手觸 摸,並請檢查系統是否散熱不良。 ‧ 在安裝或是卸除周邊產品時請先關閉電源。 ‧ 在
用電安全 電磁安全 ‧ 拆裝任何元件或是搬移服務器之前,請先確定與其連接的所有電源都已經拔掉。 ‧ 拆裝任何元件上連接的數據線之前,請先拔掉連接的電源線,或是先安裝數據線 之後再安裝電源線。 ‧ 使用一隻手拆裝數據線,以避免接觸到兩個不同電位表面造成不當的電流突波衝 擊生成。 ‧ 服務器電源線請勿與其他事物機器共用同一個插座,儘量不要使用延長線,最好 能夠連接一台不斷電系統 UPS。 靜電元件 處理器、內存、主板、擴展卡、磁盤、硬盤等設備,是由許多精密的集成電路與其 它元件所構成,這些集成電路很容易因為遭受靜電的影響而損壞。因此,在拆裝任何 元件之前,請先做好以下的準備: ‧ 如果您有靜電環等防靜電設備,請先戴上。 ‧ 假如您所處的環境並沒有防靜電地板,開始拆裝服務器之前,請您先將身體可能 帶的靜電消除。 ‧ 在尚未準備安裝前,請勿將元件由防靜電袋中取出。 ‧ 將元件由防靜電袋中取出時,請先將它與服務器金屬平面部份碰觸,釋放靜電。 ‧ 拿持元件時儘可能不觸碰電路板,及有金屬接線的部份。 ‧ 請勿用手指接觸服務器之連接器、IC 腳位、附加卡之金手指等地方。 ‧ 欲暫時置放元件時請放置在防靜電墊或是防靜電袋上,
關於本用戶手冊 本用戶手冊主要是針對有經驗且具有個人電腦硬件組裝知識的用戶所撰寫的。本手 冊可以幫助您創建起最新、功能強大的華碩服務器。手冊內容介紹本產品各部份元件 的拆裝、設置,因此,部份元件可能是選購配備,並未包含在您的產品當中,假如您 有需要選購該配備,請向本公司授權經銷商洽詢。 章節說明 本用戶手冊的內容結構如下: 第一章:系統導覽 本章以清楚的圖標帶您認識華碩 RS500A-E11 系列服務器的功能及特色,包括系 統的前、後面板以及內部功能的介紹。 第二章:硬件安裝 本章以逐步說明的方式,教您如何將系統所需的零組件正確地安裝至本服務器裡 頭。 第三章:高級安裝 本章提供您本服務器的機架安裝及使用方法。 第四章:主板信息 本章提供您有關本服務器內置主板的相關信息,包括主板的結構圖、Jumper 設置 以及連接端口位置等。 第五章:BIOS 程序設置 本章提供您本服務器之 BIOS 的升級與管理及 BIOS 設置的相關信息。 第六章:安裝驅動程序 本章節將提供您相關驅動程序的安裝與說明。 viii
提示符號 以下為本手冊所使用到的各式符號說明: 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到主板元件。不當的動 作可能會對產品造成損害。 注意:重點提示,重要的注意事項。您必須遵照用戶手冊所描述之方式 完成一項或多項軟硬件的安裝或設置。 說明:小祕訣,名詞解釋,或是進一步的信息說明。提供有助於完成某 項工作的訣竅和其他額外的信息。 哪裡可以找到更多的產品信息 您可以通過下面所提供的兩個渠道來獲得您所使用的華碩產品信息以及軟硬件的升 級信息等。 1. 華碩網站 您可以到 http://w3.asus.com.cn 華碩電腦互聯網,來取得所有關於華碩軟硬件產 品的各項信息。 2. ASUS Control Center(ACC)用戶手冊 本用戶手冊介紹如何設置並使用華碩伺服器管理工具,請至 asuscontrolcenter. asus.
電子電器產品有害物質限制使用標示要求:圖中之數字為產品之環保 使用期限。僅指電子電器產品中含有的有害物質不致發生外洩或突變 從而對環境造成污染或對人身、財產造成嚴重損害的期限。 30 產品中有害物質的名稱及含量: 部件名稱 鉛 (Pb) 汞 (Hg) x o 印刷電路板及其 電子組件 外部信號連接頭 及線材 外殼 軟驅 電池 光驅 散熱設備 電源適配器 硬盤 中央處理器與內 存 有害物質 六價鉻 鎘 (Cd) (Cr(VI)) o 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) o o o x o o o o o o x x x x x x o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o x o o o o o 本表格依據 SJ/T 11364 的規定編制。 ○: 表示該有害物質在該部件所有均質材料中的含量均在 GB/T 26572 規定的限量 要求以下。 ×: 表示該有害物質至少在該部件的某一均質材料中的含量超出 GB/T 26572 規定 的限量要求。
第一章: 系統導覽 本章將介紹本服務器的各項組成元件,其中包括系統的 前、後面板以及內部功能的總體介紹。 1
1.1 產品包裝內容 以下列本服務器包裝內的組件。 標準元件 機種型號 RS500A-E11-RS4U、RS500A-E11-RS12U 機箱 華碩 R12F 1U 機架式機箱 主板 華碩 KMPA-U16 服務器主板 硬件組件 2 x 800W 備援式電源(PSU)或 2 x 850W 備援式電源(PSU) 4 x 可熱插拔 3.5 英寸或 2.5 英寸硬盤抽取架(RS500A-E11RS4U) 12 x 可熱插拔 2.
1.
1.
機種型號 RS500A-E11-RS4U RS500A-E11-RS12U 輔助存儲設備插槽(軟碟/光驅) 2 x USB 3.2 Gen 1 連接端 口 前端輸出 / 輸入連接端口 1 x VGA 連接端口 2 x USB 3.
1.4 前端面板 本服務器的前端面板提供了簡單的存取功能,包括電源按鈕、重置按鈕、 相關的 LED 指示燈及 USB 連接端口,可方便您隨時瞭解系統的狀況。 關於前面板 LED 指示燈的介紹,請參考 1.7.1 前面板指示燈 的說明。 RS500A-E11-RS4U 機架螺絲 硬盤插槽 1 硬盤插槽 2 硬盤插槽 4 硬盤插槽 3 4 3 2 機架螺絲 1 顯示器連接端口 USB 3.2 Gen 1 連接端口 網絡端口 1-4 指示燈 信息指示燈 重置(Reset)按鈕 硬盤存取指示燈 Location 開關含指示燈 電源按鈕含指示燈 Asset tag(財產標籤) ‧ 插槽 1 至 4 支持 NVMe / SATA / SAS 設備,SAS 硬盤則需搭配 選配的 HBA/RAID 卡使用。(支持 tri-mode 卡) ‧ 所有插槽皆支持 3.5 / 2.
1.5 後端面板 後端面板包含了所有連接設備的接口、後置風扇等。下圖即為服務器後端面板圖 標。 擴展卡插槽 擴展卡插槽 擴展卡插槽 OCP 3.0 夾層卡插槽 網絡端口 1 電源與電源線連接孔 Q-Code 指示燈 VGA 連 網絡端口 2 電源按鈕含指示燈 USB 3.
1.6 內部組件 下圖即為本服務器的標準內部組件: RS500A-E11-RS4U 1. 備援式電源 2. 蝴蝶型轉接卡(G e n4 x16 link 與 x8 link) 3. 轉接卡(Gen4 x16 link) 4. OCP 3.0 卡插槽 5. 華碩 KMPA-U16 服務器主 板 6. 系統風扇 7. S A T A/S A S/N V M e 背板 (隱藏) 8. 前側 I/O 面板 9. 4 x 3.5 英寸硬盤擴展插槽 10.
RS500A-E11-RS12U 1. 備援式電源 2. 蝴蝶型轉接卡(G e n4 x16 link 與 x8 link) 3. 轉接卡(Gen4 x16 link) 4. OCP 3.0 卡插槽 5. 華碩 KMPA-U16 服務器主 板 6. 系統風扇 7. 4 x 2.5 英寸內置硬盤擴展 插槽 8. S A T A/S A S/N V M e 背板 (隱藏) 9. 12 x 2.5 英寸硬盤擴展插槽 10.
1.7 LED 顯示燈號說明 1.7.
RS500A-E11-RS12U 電源按鈕 電源指示燈 網絡端口 1 與 3 指示燈 網絡端口 2 與 4 指示燈 重置(Reset)按鈕 信息指示燈 Location 開關 Location 指示燈 指示燈 顯示 說明 電源指示燈 亮燈 系統電源開啟 熄滅 亮燈 熄滅 亮燈 熄滅 閃爍 亮燈 系統正常 提醒某個硬件監控事件 一切正常 按下 Location 按鈕(再按一次則關閉) 無連接網絡 正在存取數據 已連接網絡 信息指示燈 Location 指示燈 網絡指示燈 1.7.
1.7.3 硬盤狀態指示燈 RS500A-E11-RS4U RS500A-E11-RS12U 紅燈 綠燈 紅燈 綠燈 存儲設備指示燈說明 綠燈 亮起 電源已開啟(檢測到有存儲設備存在) 紅燈 亮起 RAID 存儲設備失效並且應立即更換(雖有插入存儲設備 但檢測錯誤) 綠燈 / 紅燈 閃爍 RAID 重建正在進行 綠燈 / 紅燈 閃爍 RAID Locating 綠燈 / 紅燈 熄滅 未安裝存儲設備 綠燈 讀取 / 寫入數據至存儲設備中 閃爍 1.7.
1.7.
Action PHASE PSP Boot PSP Boot Loader phase (Error Post Codes) POST CODE 0x39 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F 0x40 0x41 0x42 0x43 0x44 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5E 0x5F 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 TYPE Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error Error E
Action PHASE PSP Boot PSP Boot Loader phase (Status Post Codes) POST CODE 0xA0 0xA1 0xA2 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA 0xAB 0xAC 0xAD 0xAE 0xAF 0xB0 0xB1 0xB2 0xB3 0xB4 0xB5 0xB6 0xB7 0xB8 0xB9 0xBA 0xBB 0xBC 0xBD 0xBE 0xBF 0xC0 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 0xC9 0xCA 0xCB 0xCC 0xCD 0xCE 0xCF 0xD0 0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 0xD8 0xD9 TYPE Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Pro
Action PHASE PEI(Pre-EFI Initialization) phase Quick VGA DXE(Driver Execution Environment) phase Normal boot BDS(Boot Device Selection) phase Operating system phase 1-16 第一章:系統導覽 POST CODE 0x10 0x11 0x15 0x19 0x32 0x33 0x34 0x35 0x36 0x37 0x3B 0x4F 0x60 0x61 0x62 0x63 0x68 0x69 0x6A 0x70 0x71 0x72 0x78 0x79 0xD0 0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B 0x9C 0x9D 0xb2 0xb3 0xb4 0xb6 0xb7 0xA0 0xA1 0xA2 0xA3 0x00~0xFF 0xA8 0xA9 0xAB 0xAD 0xAE 0xAA 0xAC TYPE Progress Progress Progres
AMD EPYC™ 7003 系列處理器 Action PHASE SEC Start up Security Phase PSP Boot PSP Boot Loader phase (Error Post Codes) POST CODE 0x01 0x02 0x03 0x04 0x05 0x06 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2A 0x2B 0x2C 0x2D 0x2E 0x2F 0x30 0x31 0x32 0x33 0x34 0x35 0x36 0x37 0x38 0x39 TYPE Progress Progress Progress Progress Progress Progress error
Action PSP Boot PHASE PSP Boot Loader phase (Error Post Codes) POST CODE 0x3A 0x3B 0x3C 0x3D 0x3E 0x3F 0x40 0x41 0x42 0x43 TYPE error error error error error error error error error error 0x44 error 0x45 0x46 0x47 0x48 0x49 0x4A 0x4B 0x4C 0x4D 0x4E 0x4F 0x50 0x51 0x52 0x53 0x54 0x55 0x56 0x57 0x58 0x59 0x5A 0x5B 0x5C 0x5E 0x5F 0x60 0x61 0x62 0x63 0x64 0x65 0x66 0x67 error error error error error error error error error error error error error error error error error error error error error error er
Action PSP Boot PHASE PSP Boot Loader phase (Status Post Codes) PEI(Pre-EFI Initialization) phase Quick VGA DXE(Driver Execution Environment) phase POST CODE 0x7B 0x7C TYPE error error 0x7D error 0x7E 0x7F 0x80 error error error 0x81 error 0x82 error 0x83 0x84 error error 0x85 error 0x86 0x87 0x88 0x89 0x8A 0x8B 0x8C 0x8D 0x8E error error error error error error error error error 0x8F error 0x90 0x91 error error 0x92 error 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B 0x9C 0x9D 0x
Action Normal boot PHASE BDS(Boot Device Selection) phase Operating system phase 1-20 第一章:系統導覽 POST CODE 0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97 0x98 0x99 0x9A 0x9B 0x9C 0x9D 0xb2 0xb3 0xb4 0xb6 0xb7 0xA0 0xA1 0xA2 0xA3 0x00~0xFF 0xA8 0xA9 0xAB 0xAD 0xAE 0xAA 0xAC TYPE Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress Progress P
第二章: 硬件安裝 本章節要告訴您如何安裝及卸除本服務器各個部分的組 件,以及在安裝過程中必需注意的事項。 2
2.1 機箱上蓋 2.1.1 打啟動箱後半部上蓋 1. 使用螺絲起子鬆開機箱兩側的 2 顆螺絲。 2. 鬆開後側面板上的指旋螺絲。 3. 握住機箱上蓋向後推,使之鬆開脫離機箱。 4.
2.2 中央處理器(CPU) 本主板具備 Socket SP3 處理器插槽,本插槽是專為 AMD EPYC™ 7002 & 7003 系列處理器所設計。 • 在您購買本主板之後,請確認在處理器插座上附有一個 P n P 保護 蓋,並且插座接點沒有彎曲變形。若是保護蓋已經毀壞或是沒有保護 蓋,或者是插座接點已經彎曲,請立即與您的經銷商聯絡。 • 在 安 裝 完 主 板 之 後 , 請 將 即 插 即 用 的 保 護 蓋 保 留 下 來 。 只 有 在 S o c k e t S P3 插槽上附有即插即用保護蓋的主板符合 R e t u r n Merchandise Authorization(RMA)的要求,華碩電腦才能為您處理 產品的維修與保修。 • 本保修不包括處理器插座因遺失、錯誤的安裝或不正確的移除即插即 用保護蓋所造成的毀損。 2.2.1 安裝中央處理器 請依照以下步驟安裝處理器: 1. 依照 2.1 機箱上蓋 的說明移除後端上蓋板。 2.
3. 鬆開固定安裝盒上蓋的螺絲。 4. 輕輕向上掀起邊框。 安裝盒上蓋 邊框 外蓋 5.
6. 將裝有 C P U 的托架安裝至邊框 內,並移除保護蓋。 裝有 CPU 的托架只能以 單一方向正確地安裝到邊 框。切記請勿用力地將裝 有 CPU 的托架以錯誤的 方向進行安裝。 裝有 CPU 的托架 外蓋 保護蓋 7. 對齊 CPU 插槽蓋上邊框。 裝有 CPU 的托架 8. 將安裝盒上蓋的三個螺絲使用螺絲起子 分別鎖上。 安裝盒上蓋螺絲規格為 T20, 扭矩值建議為 16.1±1.2 kgfcm (14.0±1.
9. 將散熱器上的四個螺絲,使用十字螺絲 起子分別鎖上,使散熱器固定於主板 上。將四個螺絲使用螺絲起子依對角的 鎖定方式分別鎖上,使散熱器穩固於主 板上。 散熱器螺絲規格為 T20,扭矩 值建議為 16.1±1.2 k g f-c m (14.0±1.
2.3 系統內存 2.3.1 概述 本主板配置有 16 個 DDR4 DIMM(Double Data Rate 4,雙倍數據傳輸率)內存 條插槽。 下圖為 DDR4 DIMM 內存條插槽在主板上之位置。 2.3.
2.3.3 安裝內存條 安裝移除內存條前,請確認已安裝中央處理器、散熱器與導風罩。 請依照下面步驟安裝內存條: 內存條缺口 1. 先將內存條插槽的固定卡扣扳開。 2. 將內存條的金手指對齊內存條插槽的 溝槽,並且在方向上要注意金手指的 缺口要對準插槽的凸起點。 插槽凸起點 往外扳開內存條插 槽的卡扣 內存插槽上的凹槽為設計只一個方向供內存條插入,請在裝入前,確定 內存條與內存插槽上的安裝方向是契合的。 3. 最後緩緩將內存條插入插槽中,若無 錯誤,插槽的卡扣會因內存條安裝而 自動扣到內存條的凹孔中。 卡扣會在內存條正確 安裝後自動扣上 請將內存條缺口對準插槽的凸起點並垂直插入,以免造成內存條缺口損 壞。 2.3.4 取出內存條 請依照以下步驟取出內存條: 1. 依照 2.1 機箱上蓋 的說明移除後端上 蓋板。 2. 壓下內存條插槽的固定卡扣以鬆開內存 條。 3.
2.4 安裝硬盤 RS500A-E11-RS4U 本系統支持 4 個 3.5 英寸熱插拔 SATA/SAS 硬盤設備或 4 個 2.5 英寸熱插拔 NVMe 硬盤設備。硬盤的安裝方式,是經由裝入連接在主板 SATA/SAS/NVMe 背板 上的模塊式硬盤擴展槽來使用。 硬盤插槽 1 硬盤插槽 2 硬盤插槽 3 硬盤插槽 4 4 3 2 1 ‧ 插槽 1 至 4 支持 NVMe / SATA / SAS 設備,SAS 硬盤則需搭配 選配的 HBA/RAID 卡使用。(支持 tri-mode 卡) ‧ 所有插槽皆支持 3.5 / 2.5 英寸存儲設備。 RS500A-E11-RS12U 本系統支持 12 個 2.
2.5.1 安裝 3.5 英寸存儲設備(RS500A-E11-RS4U) 1. 請按下固定扣。 2. 將握把朝左扳開時,硬盤槽便會向外 滑出,請順勢將硬盤擴展槽往主機的 前方抽離。 3. 將準備安裝的存儲設備安裝至硬盤槽。 4. 當存儲設備安裝完畢後,請以手緊握 住硬盤槽握把安裝系統的插槽中,將 其輕推至機箱底部。將板手輕輕地推 回原位並輕扣固定,使硬盤槽能夠緊 密地固定在機箱中。 ‧ 當安裝後,硬盤槽上的 SATA/SAS/NVMe 接口會完全與背板上的插 座契合。 ‧ 如果硬盤槽有正確地安裝,您將會看到硬盤槽外緣與機箱呈現切齊的 狀態。 5. 若要安裝其他 3.
2.5.2 安裝 2.5 英寸存儲設備(RS500A-E11-RS4U) 1. 參考 2.5.1 安裝 3.5 英寸存儲設備(RS500A-E11-RS4U) 的步驟 1-2 取出硬 盤擴展槽。 2. 將準備安裝的 2.5 英寸存儲設備安裝至硬 盤槽,並對齊螺絲孔位。 3. 鎖上隨附的螺絲將 2.5 英寸存儲設備固定 於硬盤槽 4. 參考 2.5.1 安裝 3.5 英寸存儲設備(RS500A-E11-RS4U) 的步驟 4 裝回硬盤 擴展槽。 ‧ 當安裝後,硬盤槽上的 SATA/SAS/NVMe 接口會完全與背板上的插 座契合。 ‧ 如果硬盤槽有正確地安裝,您將會看到硬盤槽外緣與機箱呈現切齊的 狀態。 5. 若要安裝其他 2.
2.4.3 安裝 2.5 英寸存儲設備至前端插槽(RS500A-E11-RS12U) 1. 請按下固定扣。 2. 將握把朝左扳開時,硬盤槽便會向外 滑出,請順勢將硬盤擴展槽往主機的 前方抽離。 3. 將準備安裝的存儲設備安裝至硬盤槽。 4. 當存儲設備安裝完畢後,請以手緊握 住硬盤槽握把置入系統的插槽中,將 其輕推至機箱底部。將板手輕輕地推 回原位並輕扣固定,使硬盤槽能夠緊 密地固定在機箱中。 ‧ 當置入後,硬盤槽上的 SATA/SAS/NVMe 接頭會完全與背板上的插 座契合。 ‧ 如果硬盤槽有正確地安裝,您將會看到硬盤槽外緣與機箱呈現切齊的 狀態。 5. 若要安裝其他 2.
2.4.4 安裝 2.5 英寸存儲設備至內置插槽(RS500A-E11-RS12U) 1. 依照 2.1 機箱上蓋 的說明移除後端上蓋板。 2. 移除內置插槽架前端的緩衝。 3. 將內置插槽架的固定扣向外拉(A),以將插槽架向上抬起(B),並鬆開內置插 槽架的固定扣(C)。內置插槽架固定扣需鎖定才能便於使用內置插槽(D)。 內置插槽架固定扣 4.
5. 將準備安裝的存儲設備安裝至硬盤槽。 6. 當存儲設備安裝完畢後,請以手緊握住硬盤槽握把置入內置插槽架中。將板手輕 輕地推回原位並輕扣固定,使硬盤槽能夠緊密地固定在內置插槽架中。 7. 若要安裝其他 2.
8.
2.5 擴展插槽 2.5.1 安裝擴展卡至轉接卡支撐架 在 PCIE 插槽上已預先安裝一組轉接卡支撐架,請移除轉接卡支撐架以安裝 x8 或 x16 擴展卡。 請依照以下步驟,安裝 x8 或 x16 擴展卡: 1. 使用雙手握住轉接卡的兩端,再將其從主板的 PCI Express 插槽中取出。 2. 將此轉接卡放置在平坦的桌面上。 3.
2. 卸除固定金屬擋板與轉接卡支撐架的螺絲,然後取下金屬擋板。 4. 將擴展卡插入 PCIe 插槽,確認金手指完全插入插槽中。 5. 將金屬托架鎖裝回並逆時針轉動,將擴展卡固定於轉接卡支撐架上。 6.
2.5.2 安裝擴展卡至蝴蝶型轉接卡支撐架 在 PCIE 插槽上已預先安裝一組蝴蝶型轉接卡支撐架,請移除蝴蝶型轉接卡支撐架 以安裝 x8 或 x16 擴展卡。 請依照以下步驟,安裝 x8 或 x16 擴展卡: 1. 使用雙手握住蝴蝶型轉接卡的兩端,再將其從主板的 PCI Express 插槽中取出。 2. 將蝴蝶型轉接卡放置在平坦的桌面上。 3.
4. 將擴展卡插入 PCIe 插槽,確認金手指完全插入插槽中。 5. 將金屬托架鎖裝回並逆時針轉動,將擴展卡固定於蝴蝶型轉接卡支撐架上。 6. 請參考 2.5.3 安裝華碩 PIKE II 卡 的說明以安裝擴展卡至蝴蝶型轉接卡支撐架上 的其他 PCIe 插槽。 7.
2.5.3 安裝華碩 PIKE II 卡 您可以將華碩 PIKE II 卡安裝至任一轉接卡支撐架的 PCIe 插槽上,在此以安裝至 蝴蝶型轉接卡支撐架為例。 請依照以下步驟安裝華碩 PIKE II 卡: 1. 使用雙手握住蝴蝶型轉接卡的兩端,再將其從主板的 PCI Express 插槽中取出。 2. 將蝴蝶型轉接卡放置在平坦的桌面上。 3.
4. 將華碩 PIKE II 卡插入 PCIe 插槽,確認金手指完全插入插槽中。 5. 將金屬托架鎖裝回並逆時針轉動,將華碩 PIKE II 卡固定於蝴蝶型轉接卡支撐架 上。 6. 將 mini-SAS HD 排線連接至華碩 PIKE II 卡的插槽。 7.
2.5.4 安裝 M.2 擴展卡 您可以在主板上提供的 M.2 插槽上面安裝一張 M.2 擴展卡。 請依照以下的步驟安裝 M.2 擴展卡: 1. 使用雙手握住轉接卡的兩端,再將其從主板的 PCI Express 插槽中取出。 2. 找到主板上的 M.
3. 在主板上選擇欲安裝的 M.2 卡的螺絲孔位置,並鎖上螺絲座。 4. 將 M.2 擴展卡對準主板上的 M.2(NGFF)插槽裝入 ,並鎖上螺絲固定。 5.
2.5.5 安裝 OCP 3.0 卡 1. 移除固定 OCP 3.0 插槽金屬托架的螺絲(A),並將金屬托架取下(B)。 2. 將 OCP 3.0 卡安裝至 OCP 3.0 插槽(A),接著鎖上指旋螺絲固定 OCP 3.
2.5.6 設置擴展卡 安裝好擴展卡後,接著須通過軟件設置來調整擴展卡的相關設置。 1. 啟動電腦,然後更改必要的 BIOS 程序設置。若需要的話,您也可以參閱第五章 BIOS 程序設置以獲得更多信息。 2. 為加入的擴展卡指派一組尚未被系統使用到的 IRQ。請參閱下頁表中所列出的中 斷要求使用一覽表。 3.
2.6 連接排線 ‧ 系統內的排線在出廠前都已經預先連接妥當。您不需再另外安裝,除 非您需要更換或安裝增加的硬件,才需要重新連接/卸除。 ‧ 請參考第四章以了解更多關於排線與插座連接的相關信息。 預先連接的系統排線 1. 24-pin EATXPWR1 電源接口(連接至電源面板) 2. 8-pin EATX12V1 電源接口(連接至電源面板) 3. 4-pin EATX12V2 電源接口(連接至電源面板) 4. 面板連接插座(連接至前置 I/O 面板) 5. 系統風扇 FRNT_FAN1-7 連接插座(主板至系統風扇) 6. 系統風扇 FRNT_FAN8 連接插座(選配,主板至系統風扇) 7.
2.
RS500A-E10-RS12U 連接至主板上的 SLMSATA_PCIE8 以支持內置插槽 1 與 2 使用 NVMe 連接至主板上的 SLMSATA_PCIE7 以支持內置插槽 3 與 4 使用 NVMe 連接至主板上的 SLMSATA_PCIE7 以支持內置插 槽 1 至 4 使用 SATA HDD12 HDD34 MSAS_HD1 SLIMSATA_PCIE1 SLIMSATA_PCIE2 PWR0501 連接至 NVMe/SAS/SATA 存儲設備 SLED1 NVME3 NVME4 連接至主板上的 SLMPCIE6 以支持插槽 11 與 12 使用 NVMe 連接至主板上的 SLMPCIE4 以支持插 槽 7 與 8 使用 NVMe SLED3 ALED3 SLED4 ALED4 NVME1 ALED1 SLED2 NVME2 ALED2 連接至主板上的 SLMPCIE2 以支持插 槽 3 與 4 使用 NVMe 連接至 HBA / RAID 卡以支 持插槽 9 至 12 使用 SAS, 或連接至主板上的 SLMSATA_PCIE7 插槽以支持插槽 9 至 12 使用 S
2.8 存儲設備設置與連接排線 本章節說明服務器建議的存儲設備設置方式,當您開始安裝或移除存儲設備排線前 ,請先確認各硬盤插槽是否安裝正確的硬盤規格。 請參考 2.4 安裝硬盤 的詳細說明。 RS500A-E11-RS4U 硬盤插槽 1 硬盤插槽 2 硬盤插槽 3 硬盤插槽 4 4 3 2 1 ‧ 插槽 1 至 4 支持 NVMe / SATA / SAS 設備,SAS 硬盤則需搭配 選配的 HBA/RAID 卡使用。(支持 tri-mode 卡) ‧ 所有插槽皆支持 3.5 / 2.5 英寸存儲設備。 RS500A-E11-RS12U 前端插槽 硬盤插槽 1 硬盤插槽 3 硬盤插槽 5 硬盤插槽 7 硬盤插槽 9 硬盤插槽 11 硬盤插槽 2 硬盤插槽 4 硬盤插槽 8 硬盤插槽 10 硬盤插槽 12 硬盤插槽 6 ‧ 插槽 1 至 12 支持 NVMe / SATA / SAS 設備,SAS 硬盤則需搭配 選配的 HBA/RAID 卡使用。 ‧ 所有插槽皆支持 2.
2.8.1 4 x NVMe 與 4 x SATA 存儲設備設置與連接排線(RS500AE11-RS4U) 本章節圖示可能因機型而異,僅供參考。 背板連接端口 排線 連接至 SLIMPCIE1 Slimline SAS 至 Slimline SAS 主板上的 SLMPCIE1 SLIMPCIE2 Slimline SAS 至 Slimline SAS 主板上的 SLMPCIE2 MSAS_HD1 Slimline SAS 至 2 x Mini-SAS HD 主板上的 SLMSATA_PCIE7 1. 請將硬盤安裝至支持的硬盤插槽。 請參考 2.
2.
2.8.
1. 請將硬盤安裝至支持的硬盤插槽。 請參考 2.4 安裝硬盤 的詳細說明。 前端插槽 NVMe/SATA NVMe/SATA NVMe/SATA NVMe/SATANVMe/SATA NVMe/SATA NVMe/SATA NVMe/SATA NVMe/SATA NVMe/SATANVMe/SATA NVMe/SATA 內置插槽(選配) 上層:SATA 下層:SATA 上層:SATA 下層:SATA 2.
2. 連接 Slimline SAS 排線與 Slimline SAS 至 2 x Mini SAS HD 排線至主板與前端背 板。 3.
2.8.
1. 請將硬盤安裝至支持的硬盤插槽。 請參考 2.4 安裝硬盤 的詳細說明。 前端插槽 NVMe NVMe NVMe NVMe NVMe NVMe NVMe NVMe NVMe NVMe NVMe NVMe 內置插槽(選配) 上層:NVMe 下層:NVMe 上層:NVMe 下層:NVMe 2.
2. 連接 Slimline SAS 排線至主板與前端背板。 3.
2.9 卸除系統組件 當您在安裝或卸除系統設備或是替換損壞的零組件時,或許需要卸除先前所安裝的 系統組件。而本章節的內容就是要告訴大家如何卸除與重新安裝下列各項系統組件。 安裝/卸除系統組件之前,請先關閉系統電源。 您可能需要在安裝組件前,先移除先前安裝的組件或出廠組件。 2.9.1 備援式電源(PSU)模塊 您可依照以下的步驟,更換損壞的備援式電源(PSU)模塊: 1. 握住電源(PSU)上的握把(A),然後使用拇指將右側的固定閂朝左推讓電源 (PSU)鬆脫(B)。接著可以將此電源(PSU)模塊,從機箱中拉出(C)。 握把 固定閂 2. 準備好要安裝的新電源(PSU)。 3.
• 系統會自動將二個電源(PSU)集成為一個單一電源(PSU),而集 成後的輸出電源會因輸入電壓不同而有所不同。 800W 輸入電壓 每個電源供應器的最大輸出電源 (瓦特) 100V-127Vac, 10.0A, 50-60Hz 800W 200V-240Vac, 5.0A, 50-60Hz 800W 850W 輸入電壓 每個電源供應器的最大輸出電源 (瓦特) 100V-127Vac, 11.0A, 47-63Hz 850W 200V-240Vac, 5.
2-40 第二章:硬件安裝
第三章: 高級安裝 本章節要告訴您,如何使用滑軌套件將本服務器安裝至 機架中,以及在安裝過程中必須注意的事項。 3
3.1 免工具標準式滑軌套件 免工具的滑軌套件設計,提供您輕鬆將滑軌裝上機架並安裝服務器至機架中,而無 須使用任何工具。這個套件並提供金屬止擋,可以讓您在安裝服務器時提供額外的支 撐和穩定性。 免工具滑軌套件包含了以下組件: 固定閂 螺絲組 固定閂螺絲 滑軌墊圈 滑軌螺絲 Tool-less rack rails 3.1.1 安裝免工具機架滑軌 請依照以下步驟,將免工具機架滑軌安裝至機架上: 1.
2. 選擇所需的空間和適當的機架滑軌(左和右)放在機架的相對位置上。 在這 1U 的空間裡面要有三個方形安裝孔與在上方與底部包含二個薄型 的間隔,如下圖圈選處。 1U 3. 上推彈簧鎖,然後將螺栓插入已選定在機架上的方形安裝孔。 4. 上推滑軌另一端的彈簧鎖,然後插入已選定在機架上的方形安裝孔。如有必要, 請將機架滑軌拉長以便於安裝。 5.
6. 抬起服務器,並裝入機架滑軌。 ‧ 請確認機架滑軌機櫃與機架裝配的位置是穩定的,且牢靠地站立在同 一水平高度上。 ‧ 強烈推薦至少需要兩位身強體壯的人來運行這部份的安裝操作。 ‧ 如有必要,推薦使用適當的起重工具以輔助吊裝。 RS500A-E11-RS4U RS500A-E11-RS12U 請確認服務器兩側的結點(knots)裝入機架滑軌的安裝孔裡。。 圖示僅供參考。 3.1.2 滑軌尺寸 43.6mm 900mm 43.
3.2 滾珠軸承機架安裝套件 滑軌套件包含了以下組件: 2 x 1200 mm 機架滑軌(或 2 x 1000 mm 機架滑軌) 滑軌前端 機架滑軌 滑軌後端 4 x #6-32X4L 螺絲 4 x M4X4L 螺絲 8 x ø17.
3.2.1 安裝機架滑軌 ‧ 請確認機架滑軌機櫃與機架裝配的位置是穩定的,且牢靠地站立在同 一水平高度上。 ‧ 強烈推薦至少需要兩位身強體壯的人來運行這部份的安裝操作。 ‧ 如有必要,推薦使用適當的起重工具以輔助吊裝。 ‧ 本節步驟以 1200 mm 機架滑軌為例,1000 mm 機架滑軌的安裝步 驟幾乎相同。 ‧ 本節圖示僅供參考。 請依照以下步驟,將機架滑軌安裝至機架上: 1. 選擇所需的空間和適當的機架滑軌 (左和右)放在機架的相對位置上。 1U 在這 1U 的空間裡面要有三 個方形安裝孔與在上方與底 部包含二個薄型的間隔,如 下圖圈選處。 2.
3. 按壓彈簧鎖,然後將滑軌後端螺栓插 入已選定在機架上的方形安裝孔。 後端機架 彈簧鎖 滑軌後端 4. 將中間滑軌向外滑動直到停止。 中間滑軌 外滑軌 5. 將內滑軌向外滑動直到停止。向外滑動固定扣以移除內滑軌。 中間滑軌 內滑軌 藍色膠片 白色膠片 僅 1200mm 機架滑軌才有藍色膠片,可用於延長或收回中間滑軌。 6.
7. 移除機箱左右兩側的 3 顆螺絲,接著移除金屬板。 下圖僅顯示機箱的一側,另一側機箱的螺絲會在相同位置。 金屬板 8. 將內滑軌對準服務器兩側的結點進行安裝,並朝服務器後端滑動以固定。 2 1 9.
10. 抬起服務器並裝入機架滑軌。 2 1 11. (選配)使用 M5X20L 螺絲將滑軌 固定於機架上。 前端機架 滑軌前端 12.
RS500A-E11-RS4U RS500A-E11-RS12U 3-10 第三章:高級安裝
3.3 理線架(僅供 1200 mm 機架滑軌選配) 您可以額外安裝理線架(C M A)來幫助收納及配置服務器的纜線。理線架設計為 可移動式元件,方便您依機架滑軌移動服務器而不必移動理線架。 外側連接器 內側連接器 勾環綁帶 樞軸連接器 信號線綁帶 3.3.1 安裝理線架 請依照以下步驟安裝理線架: 1. 安裝機架滑軌。 請參考 3.1 滑軌套件 的說明安裝機架滑軌。 2.
3. 將理線器上的 3 個連接器對齊機架滑軌上的連接器。 中間滑軌連接器 樞軸連接器 內滑軌連接器(隱藏) 內側連接器 中間滑軌連接器 外側連接器 本章節的安裝步驟以左樞軸為例,右樞軸的安裝步驟極為相似。 4. 將內滑軌連接器連接至理線架 上的內側連接器。 5.
6. 將另一端的中間滑軌連接器連接至理線架上的樞軸連接器。 7.
3-14 第三章:高級安裝
第四章: 主板信息 在本章中要告訴您在安裝系統元件時所必須完成的主板 安裝程序。詳細內容有:頻率開關設置、跳線選擇區設置 以及主板的各種設備接口。 4
4.
主板的各項元件 跳線選擇區 頁碼 1. Clear RTC RAM (3-pin CLRTC1) 4-4 2. VGA controller setting (3-pin VGA_SW1) 4-5 3. LANNCSI setting (3-pin LANNCSI_SEL1) 4-5 4. Baseboard Management Controller setting (3-pin BMC_EN1) 4-6 5. DMLAN setting (3-pin DM_IP_SEL1) 4-6 6. IPMI SW setting (3-pin IPMI_SW1) 4-7 7. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) 4-7 8. LAN controller settings (3-pin LAN_SW1-2) 4-8 指示燈 頁碼 1. Standby Power LED (SBPWR1) 4-9 2.
4.2 跳線選擇區 1. CMOS 組態數據清除(3-pin CLRTC1) 在主板上的 CMOS 內存中記載著正確的時間與系統硬件組態等數據,這些數 據並不會因電腦電源的關閉而遺失數據與時間的正確性,因為這個 CMOS 的電 源是由主板上的鋰電池所供應。想要清除這些數據,可以依照下列步驟進行。 您可以依照以下的步驟,清除 COMS RTC RAM 數據: 1. 關閉電腦電源,拔掉電源線。 2. 將 CLRTC 接針由 [1-2](默認值)改為 [2-3] 約五∼十秒鐘(此時即清除 CMOS 數據),然後再將接針改回 [1-2]。 3. 插上電源線,開啟電腦電源。 4.
2. VGA 控制器設置(3-pin VGA_SW1) 您可以通過本功能的設置來開啟或關閉主板內置之 V G A 圖形顯示控制器功 能。默認值為開啟 [1-2] 。 3.
4. BMC 設置(3-pin BMC_EN1) 本接針提供您啟用(默認)或關閉主板內置的 BMC 控制器。 5. DMLAN 設置(3-pin DM_IP_SEL1) 本接針提供您選擇 DMLAN 設置。設置為 [2-3] 以強制 DMLAN IP 使用固定模式 (IP=10.10.10.10, submask=255.255.255.
6. IPMI SW 設置(3-pin IPMI_SW1) 本跳線帽提供您選擇 GPU 感應器的通訊協定。 7.
8.
4.3 內置指示燈 1. 電力警示燈(SBPWR1) 當主板上內置的電力指示燈亮著時,表示當前系統是處於正常運行、省電模式 或者軟關機的狀態中,並非完全斷電。這個警示燈可用來提醒您在安裝或卸除任 何的硬件設備之前,都必須先卸除電源,等待警示燈熄滅才可進行。請參考下圖 所示。 2.
3. 信息指示燈(MESLED1) 當這個內置的指示燈亮紅燈時,表示溫度異常或發生 BMC 事件記錄。 4.
4.4 內部連接端口 1. Slime PCIe 連接端口(SLMPCIE1-6) 將 PCIE 信號連接至背板上的前端轉接卡或 NVME 連接端口。 2.
3. USB 2.0(10-1 pin USB2) USB+5V USB_P6USB_P6+ GND NC 這些插槽可用來連接 USB 2.0 接口。將 USB 擴展套件連排線連接到 USB34, 然後將擴展套件安裝到機箱背部的一個空置插槽位置。這些 USB 擴展套件排線 插槽支持 USB 2.0 規格,傳輸速率高達 480 Mbps。 KMPA-U16 USB2 PIN 1 USB+5V USB_P7USB_P7+ GND B KMPA-U16 USB 2.0 connector USB 模塊為選購配備,請另行選購。 4. USB 3.2 Gen 1 連接插槽(USB3_34) USB 3.2 Gen 1 連接插槽提供高達 5 Gb/s 的數據傳輸率。Type-A 連接插槽 可以直接連接 USB 設備。 KMPA-U16 A KMPA-U16 USB 3.
5. 機箱開啟警示連接排針(2-pin INTRUSION1) 這組排針提供給設計有機箱開啟檢測功能的電腦主機機箱之用。此外,尚須搭 配一個外接式檢測設備,譬如機箱開啟檢測感應器或者微型開關。在本功能啟用 時,若您有任何移動機箱元件的動作,感應器會隨即檢測到並且送出一信號到這 組接針,最後會由系統記錄下這次的機箱開啟事件。默認設置為 CASEOPEN 與 GND 接腳短路,此功能關閉。 6.
7. 系統風扇插座(6-pin FRNT_FAN1-8) 這些插座為支持連接 0.8A–1.0A(最大 12 W)或總合 6.4 A–8.
8. TPM 排線插槽(14-1 pin TPM1) 本插座支持安全性平台模塊(TPM)系統,該系統可進行安全性保存金鑰、數 字認證、密碼與數據。此外,TPM 系統也可協助增進網絡安全,保護數字辨識 功能,並確保平台的集成性。 9. M.2(NGFF)插槽(NGFF1-2) 這個插槽用來安裝 M.2 (NGFF) SSD 模塊。 這個插槽支持 M K e y 與 2242/2260/2280/22110 類型 P C I-E 與 SATA存儲設備。 M.
10. 電源插座(24-pin EATXPWR; 8-pin EATX12V1; 4-pin EATX12V2) 這些插座供連接電源面板的電源(PSU)使用。電源(PSU)只能以單一方向 安裝至電源面板電源插座。安裝時請確認電源(PSU)確實安裝且方向正確。 請勿將顯卡連接至此插座,否則會使系統發生錯誤,並對主板或設備造 成永久損壞。 11.
12 Micro SD 存儲卡插槽(MSD1) 安裝 A S M B9 管理卡時,主板支持 S D 存儲卡 v2.00(S D H C) / v1.00 (SDXC)。 請先卸除連接的電源(包括備用電源)後再安裝存儲卡,同時您必須重 新啟動才能使系統成功讀取存儲卡。 有些存儲卡可能與主板不兼容。請確保使用能與主板兼容的存儲卡,以 避免數據遺失、存儲卡或設備損壞。 13.
14.
• Locator 按鈕/開關(BMCLOCBTN#) 這組排針為連接前面板 Locator 按鈕。這個按鈕按下後 Locator 指示燈將會亮 燈。 • 硬盤動作指示燈號接針(HDLED) 這組排針可連接到電腦主機面板上的硬盤動作指示燈,一旦硬盤有存取動作 時,指示燈隨即亮起。 15. VPP_I2C1 連接插槽(10-1 pin VPP_I2C1) 這個插槽供 Intel VMD 功能與感應器讀取使用。 16.
17. Smart Ride Through(SmaRT)設置(3-pin SMART_PSU1) 本跳線帽提供您啟用或關閉 Smart Ride Through(SmaRT)功能。本功能預 設為啟用。設置為 [2-3] 以關閉本功能。當本功能開啟時,SmaRT 允許電源不足 時系統不間斷運行。 18.
第五章: BIOS 程序設置 B I O S 程序調校的優劣與否,和整個系統的運行性能有 極大的關係。針對自己的配備來作最佳化 BIOS 設置,可 讓您的系統性統再提升。本章節將逐一說明 BIOS 程序中 的每一項配置設置。 5
5.1 管理、更新您的 BIOS 程序 下列軟件讓您可以管理與更新主板上的 BIOS 設置。 1. ASUS CrashFree BIOS 3 當 BIOS 程序毀損時,使用可啟動的 U 盤來更新 BIOS 程序。 2. ASUS EzFlash 使用 U 盤更新 BIOS。 3. BUPDATER 使用可啟動的 U 盤在 DOS 環境下更新 BIOS 程序。 上述軟件請參考相關章節的詳細使用說明。 推薦您先將主板原始的 BIOS 程序備份到可啟動的 U 盤中,以備您往後 需要再次安裝原始的 BIOS 程序。使用華碩在線更新(ASUS Update) 程序來拷貝主板原始的 BIOS 程序。 5.1.
5.1.2 使用華碩 EzFlash 更新程序 華碩 EzFlash 程序讓您能輕鬆的更新 BIOS 程序,可以不必再通過啟動盤的冗長程 序或是到 DOS 模式下運行。 請至華碩網站 http://w3.asus.com.cn 下載最新的 BIOS 程序文件。 請依照下列步驟,使用 EzFlash 來更新 BIOS: 1. 將已存好最新版 BIOS 文件的 U 盤插入 USB 接口。 2. 進入 BIOS 設置程序。來到 Tools 菜單,選擇 ASUS EZ Flash Utility 後並按下 鍵將其開啟。 ASUSTek.
5.1.3 BUPDATER 工具程序 以下的 BIOS 畫面只能參考,請依您所見的實際 BIOS 畫面為準。 BUPDATER 工具程序可以提供您在 DOS 環境下,使用存儲有更新的 BIOS 文件的 U 盤來更新 BIOS 文件。 更新 BIOS 文件 請依照以下的步驟,使用BUPDATER 工具程序來更新 BIOS 文件: 1. 請先訪問華碩網站(w3.asus.com.cn)下載最新主板的 BIOS 文件。並將文件存 儲至可啟動的 U 盤內。 2. 然後將華碩支持網站(s u p p o r t.a s u s.c o m)上的 B U P D A T E R 工具程序 (BUPDATER.exe),下載並存儲至同一個可啟動的 U 盤內。 3. 將系統啟動至 DOS 環境下,然後使用鍵盤輸入命令: BUPDATER /i [filename].CAP [ filename] 這裡的意思就是輸入存放在 U 盤裡頭的最新或原本 BIOS 文件名稱,然 後按 鍵。 A:\>BUPDATER /i[file name].
4. 程序會進行檢查文件,然後開始更新 BIOS 文件。 ASUSTek. EzFlash Utility Current Platform Platform : KMPA-U16 Version : 0215 Build date: 01/13/2021 Start Programming Flash. New Platform Platform : KMPA-U16 Version : 0401 Build date: 04/14/2021 DO NOT SHUTDOWN THE SYSTEM!!! Write 75% 請勿在更新 BIOS 程序文件時關閉或重新啟動系統,此舉將會導致系統損 毀! 5. 完成更新後,程序會回到 DOS 畫面,請重新啟動系統,通過硬盤啟動。 The BIOS update is finished! Please restart your system. C:\> 華碩 RS500A-E11 系列用戶手冊 5-5
5.2 BIOS 程序設置 主板擁有一片可編輯的固件芯片,您可以依照 5.
5.2.1 BIOS 程序菜單介紹 菜單項目 功能表列 設置值 一般說明 操作功能鍵 5.2.
5.2.3 菜單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功能,則會顯 示 Main 菜單的項目。 點擊菜單中的其他項目(如:Event Logs、Advanced、Monitor、Boot、Tool 與 Exit 等)也會出現該項目不同的選項。 5.2.4 子菜單 在菜單畫面中,若功能選項的前面有一個小三角形標記,代表此為子菜單,您可以 利用方向鍵來選擇,並且按下 鍵來進入子菜單。 5.2.5 操作功能鍵說明 在菜單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改變各項功 能。 5.2.6 一般說明 在菜單畫面的右上方為當前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動更改。 5.2.7 設置值 這些存在於菜單中的設置值是提供給用戶選擇與設置之用。這些項目中,有的功能 選項只為告知用戶當前運行狀態,並無法更改,那麼此類項目就會以淡灰色顯示。而 可更改的項目,當您使用方向鍵移動項目時,被選擇的項目以反白顯示,代表這是可 更改的項目。 5.2.
5.3 主菜單(Main) 當您進入 BIOS 設置程序時,首先出現的第一個畫面即為主菜單,內容如下圖。 5.3.1 System Language [English] 設置系統使用語言。 5.3.2 System Date [Day xx/xx/xxxx] 設置系統日期。 5.3.
5.
5.
5.5.1 Trusted Computing Configuration Security Device Support [Enabled] 可讓您啟動或關閉 BIOS 安全設備支持功能。設置值有:[Disabled] [Enabled] 5.5.2 PSP 固件版本 本菜單顯示 PSP 固件版本。 5.5.
5.5.
以下項目僅當 Custom Pstate0 設置為 [Custom] 時才會出現。 Pstate0 Freq (MHz) [0] 本項目可以指定核心頻率(MHz)。 CCD/Core/Thread Enablement 本項目可以啟用 CCD/Core/Thread Enablement。 S3 不支持 cores/threads 已被移除或關閉的系統。 CCD Control [Auto] 設置使用的 CCD 數量。設置值有:[Auto] [2 CCDs] [3 CCDs] [4 CCDs] [6 CCDs] Core Control [Auto] 設置使用的核心數量。設置值有:[Auto] [ONE (1 + 0)] [TWO (2 + 0)] [THREE (3 + 0)] [FOUR (4 + 0)] [FIVE (5 + 0)] [SIX (6 + 0)] [SEVEN (7 + 0)] SMT Control [Auto] 本項目可以用來關閉同時多運行緒。設置值有:[Disable] [Enable] [Auto] S3 不支持 cores/threads 已被移除或關閉的系統。 Prefe
Core Watchdog Core Watchdog Timer Enable [Auto] 本項目可以啟用或關閉 CPU Watchdog Timer。設置值有:[Disable] [Enable] [Auto] 以下項目僅當 Core Watchdog Timer Enable 設置為 [Enabled] 時才會出 現。 Core Watchdog Timer Interval [Auto] 設置值有:[21.461s] [10.730s] [5.364s] [2.681s] [1.340s] [669.41m s] [334.05m s] [166.37m s] [82.53m s] [40.61m s] [20.970m s] [10.484m s] [5.241ms] [2.620ms] [1.309ms] [654.08us] [326.4us] [162.56us] [80.64us] [39.
以下項目僅當 SEV-ES ASID Space Limit Control 設置為 [Manual] 時才 會出現。 SEV-ES ASID Space Limit [Auto] 本項目可以設置 SEV-ES ASID 的空間限制。設置值有:[1] – [520] Streaming Stores Control [Auto] 本項目可以啟用或關閉 Streaming Stores 功能。設置值有:[1] – [520] Local APIC Mode [Auto] 設置值有:[Compatibility] [XAPIC] [X2APIC] [Auto] ACPI _CST C1 Operation [Auto] 決定是否向操作系統宣布 C1 狀態。設置值有:[Disabled] [Enabled] [Auto] MCA error thresh enable [Auto] 本項目可以啟用或關閉 MCA 錯誤臨界值。設置值有:[False] [True] [Auto] 以下項目僅當 MCA error thresh enable 設置為 [True] 時才會出現。 MCA error thres
以下項目僅當 SNP Memory (RMP Table) Coverage 設置為 [Custom] 時 才會出現。 Amount of Memory to Cover [0] 本項目可以十六進位指定主板的系統內存。 SMEE [Auto] 本項目可以啟用或關閉 SMEE。設置值有:[Disabled] [Enabled] [Auto] Action on BIST Failure [Auto] 本項目可以設置檢測到 C C D B I S T 失敗時的動作。設置值有:[D o N o t h i n g] [Down-CCD] [Auto] Fast Short REP MOVSB [Enabled] 默認值為 1,操作系統支持時可作為分析目的設為 0。設置值有:[D i s a b l e d] [Enabled] Enhanced REP MOVSB/STOSB [Enabled] 默認值為 1,操作系統支持時可作為分析目的設為 0。設置值有:[D i s a b l e d] [Enabled] REP-MOV/STOS Streaming [Enabled] 設置值有:[Disable
Memory Addressing NUMA nodes per socket [Auto] 本項目可指定每個插槽的 N U M A 節點數量。設置值有:[N P S1] [N P S2] [NPS4] [Auto] Memory interleaving [Auto] 本項目可設置內存交插存取。設置值有:[Disabled] [Auto] Memory interleaving size [Auto] 本項目可設置內存交插存取容量。設置值有:[256 Bytes] [512 Bytes] [1 KB] [2 KB] [Auto] 1TB remap [Auto] 本項目用以嘗試重新映射 1TB。設置值有:[Do not remap] [Attempt to remap] [Auto] DRAM map inversion [Auto] 本項目可以啟用或關閉 DRAM 映射反轉。設置值有:[Disabled] [Enabled] [Auto] Location of private memory regions [Auto] 本項目可以控制私有內存區域(PSP、SMU 與 CC6)是否在內存上端或是
ACPI SLIT same socket distance [C] 本項目可以指定在相同插槽內與其他物理區域的距離。 ACPI SLIT remote socket distance [20] 本項目可以指定與遠端插槽的距離。 ACPI SLIT local SLink distance [32] 本項目可以指定在相同插槽內與 SLink 區域的距離。 ACPI SLIT remote SLink distance [3C] 本項目可以指定在其他插槽內與 SLink 區域的距離。 ACPI SLIT local inter-SLink distance [FF] 本項目可以指定在相同插槽內兩個 SLink 區域的距離。 ACPI SLIT remote inter-SLink distance [FF] 本項目可以指定在不同插槽內兩個 SLink 區域的距離。 Link GMI encryption control [Auto] 本項目可以用來設置 GMI 加密控制。設置值有:[Disabled] [Enabled] [Auto] xGMI encryption control [Auto]
xGMI TXEQ Mode [Auto] 本項目可以選擇 XGMI TXEQ/RX 模式。設置值有:[TXEQ_Disabled] [TXEQ_ Lane] [TXEQ_Link] [TXEQ_RX_Vet] [Auto] xGMI 18GACOFC [Auto] 本項目可以啟用或關閉 18G A C O F C 控制。設置值有:[A u t o] [E n a b l e] [Disable] Disable DF to external downstream IP SyncFloodPropagation [Auto] 本項目可以啟用或關閉禁止 DF 到外部 IP 同步 SYN 洪水攻擊。設置值有:[Sync Flood disabled] [Sync Flood enabled] [Auto] Disable DF sync flood propagation [Auto] 本項目可以啟用或關閉 DF 同步 SYN 洪水攻擊。設置值有:[Sync Flood disabled] [Sync Flood enabled] [Auto] Freeze DF module queues on err
以下項目僅當 Overclock 設置為 [Enabled] 時才會出現。 Memory Clock Speed [Auto] 指定內存時鐘頻率。設置值有:[Auto] [667MHz] [800MHz] [933MHz] [1067MHz] [1200MHz] [1333MHz] [1467MHz] [1600MHz] [1633MHz] [1667MHz] [1700MHz] [1733MHz] [1767MHz] [1800MHz] [400MHz] Tcl [Auto] 指定 CAS 延遲。設置值有:[Auto] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] [0Fh Clk] [10h Clk] [11h Clk] [12h Clk] [13h Clk] [14h Clk] [15h Clk] [16h Clk] [17h Clk] [18h Clk] [19h Clk] [1Ah Clk] [1Bh Clk] [1Ch Clk] [1Dh Clk] [1Eh Clk] [1Fh Clk] [20h Clk] [2
以下項目僅當 Trc Ctrl 設置為 [Manual] 時才會出現。 Trc [39] 指定 Active to Active/Refresh Delay Time。有效數值 87h-1Dh。 TrrdS [Auto] 指定 Activate to Activate Delay Time,不同分組架構(tRRD_S)。設置 值有:[Auto] [4 Clk] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] TrrdL [Auto] 指定 Activate to Activate Delay Time,相同分組架構(tRRD_L)。設置 值有:[Auto] [4 Clk] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] Tfaw Ctrl [Auto] 指定 Tfaw。設置值有:[Auto] [Manual] 以下項目僅當 Tfaw Ctrl 設置為 [Manual] 時才會出現。 Tfaw [1] 指定 Four Activa
TrdrdScL Ctrl [Auto] 指定 TrdrdScL。設置值有:[Auto] [Manual] 以下項目僅當 TrdrdScL Ctrl 設置為 [Manual] 時才會出現。 TrdrdScL [3] 指定 CAS to CAS Delay Time,相同分組架構。有效數值 Fh-1h。 TwrwrScL Ctrl [Auto] 指定 TwrwrScL。設置值有:[Auto] [Manual] 以下項目僅當 TwrwrScL Ctrl 設置為 [Manual] 時才會出現。 TwrwrScL [3] 指定 CAS to CAS Delay Time,相同分組架構。有效數值 3Fh-1h。 Trfc Ctrl [Auto] 指定 Trfc。設置值有:[Auto] [Manual] 以下項目僅當 Trfc Ctrl 設置為 [Manual] 時才會出現。 Trfc [138] 指定 Refresh Recovery Delay Time(tRFC1)。有效數值 3DEh-3Ch。 Trfc2 Ctrl [Auto] 指定 Trfc2。設置值有:[Auto] [Manual] 以下項目僅當 Trfc2
Trtp [Auto] 指定 Read CAS# to Precharge Delay Time。設置值有:[Auto] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] Tcke [Auto] 在內存時脈循環裡指定 CKE 最小值的高低脈寬調變。設置值有:[Auto] [1 Clk] [2 Clk] [3 Clk] [4 Clk] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] [0Fh Clk] [10h Clk] [11h Clk] [12h Clk] [13h Clk] [14h Clk] [15h Clk] [16h Clk] [17h Clk] [18h Clk] [19h Clk] [1Ah Clk] [1Bh Clk] [1Ch Clk] [1Dh Clk] [1Eh Clk] [1Fh Clk] Trdwr [Auto] 指定讀取至寫
TrdrdDd [Auto] 指定不同內存間讀取至讀取的周轉時間。設置值有:[Auto] [1 Clk] [2 Clk] [3 Clk] [4 Clk] [5 Clk] [6 Clk] [7 Clk] [8 Clk] [9 Clk] [0Ah Clk] [0Bh Clk] [0Ch Clk] [0Dh Clk] [0Eh Clk] [0Fh Clk] ProcODT [Auto] 指定 Processor ODT。設置值有:[Auto] [High Impedance] [480 ohm] [240 ohm] [160 ohm] [120 ohm] [96 ohm] [80 ohm] [68.6 ohm] [60 ohm] [53.3 ohm] [48 ohm] [43.6 ohm] [40 ohm] [36.9 ohm] [34.3 ohm] [32 ohm] [30 ohm] [28.
以下項目僅當 CAD Bus Timing User Controls 設置為 [Manual] 時才會出 現。 AddrCmdSetup [0] 本項目可以設置 CAD 總線信號的運行時間。設置值有:[0] – [39] CsOdtSetup [0] 本項目可以設置 CAD 總線信號的運行時間。設置值有:[0] – [39] CkeSetup [0] 本項目可以設置 CAD 總線信號的運行時間。設置值有:[0] – [39] CAD Bus Drive Strength User Controls [Auto] 本項目可以設置 C A D 總線信號為自動或手動。設置值有:[A u t o] [Manual] 以下項目僅當 CAD Bus Drive Strength User Controls 設置為 [Manual] 時才會出現。 ClkDrvStren [Auto] 設置值有:[Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0 Ohm] [24.0 Ohm] [20.0 Ohm] AddrCmdDrvStren [Auto] 設置值有:[Auto] [120.
Common RAS Data Poisoning [Auto] 設置值有:[Enabled] [Disabled] [Auto] DRAM Post Package Repair [Disable] 本項目可以啟用或關閉 D R A M P O S T P a c k a g e R e p a i r。設置值有: [Enable] [Disable] RCD Parity [Auto] 設置值有:[Enabled] [Disabled] [Auto] DRAM Address Command Parity Retry [Auto] 設置值有:[Enabled] [Disabled] [Auto] 以下項目僅當 DRAM Address Command Parity Retry 設置為 [Enabled] 時才會出現。 Max Parity Error Replay [8] 十六進位的數值 1、2 或 3 為無效。設置值有:[0] – [39] Write CRC Enable [Auto] 設置值有:[Enabled] [Disabled] [Auto] DRAM Write CRC Enable and
Phy Configuration PMU Training DFE Read Training [Auto] 開啟 DFE 並運行 2D Read Training。設置值有:[Disabled] [Enabled] [Auto] FFE Write Training [Auto] 開啟 FFE 並運行 2D Read WriteTraining。設置值有:[Disabled] [Enabled] [Auto] PMU Pattern Bits Control [Auto] 設置值有:[Auto] [Manual] PMU Pattern Bits [0] 設置值有:[0] - [9] DRAM Memory Mapping Chipselect Interleaving [Auto] 本項目可開啟或關閉經由內存芯片選擇交插存取存儲區。設置值有:[Disabled] [Auto] BankGroupSwap [Auto] 設置值有:[Enabled] [Disabled] [Auto] BankGroupSwapAlt [Auto] 設置值有:[Enabled] [Disabled] [Auto]
以下項目僅當 MBIST Enable 設置為 [Enabled] 時才會出現。 MBIST Test Mode [Auto] 本項目可以選擇 MBIST 測試模式,包括 Interface 模式或 Data Eye 模式。設 置值有:[Interface Mode] [Data Eye Mode] [Both] [Auto] MBIST Aggressors [Auto] 本項目可以啟用或關閉 M e m o r y A g g r e s s o r 測試。設置值有:[E n a b l e d] [Disabled] [Auto] MBIST Per Bit Slave Die Reporting [Auto] 設置值有:[Enabled] [Disabled] [Auto] Data Eye Pattern Select [PRBS] 設置值有:[PRBS] [SS0] [Both] Pattern Length [3] 可能選項為 N=3...
以下項目僅當 Target Static Lane Control 設置為 [Enabled] 時才會出 現。 Target Static Lane Select Upper 32 bits [0] 設置值有:[0] - [99999999] Target Static Lane Select Lower 32 bits [0] 設置值有:[0] - [99999999] Target Static Lane Select ECC [0] 設置值有:[0] - [9] Target Static Lane Value [0] 設置值有:[0] - [9] Worst Case Margin Granularity [Per Chip Select] 設置值有:[Per Chip Select] [Per Nibble] Read Voltage Sweep Step Size [1] 設置值有:[1] [2] [4] Read Timing Sweep Step Size [1] 設置值有:[1] [2] [4] Write Voltage Sweep Step Size [1] 設置值有:[1] [2] [
NBIO Common Options IOMMU [Auto] 本項目可以啟用或關閉 IOMMU。設置值有:[Disabled] [Enabled] [Auto] DMAr Support [Auto] 本項目可以啟用 DMAr 支持。設置值有:[Disable] [Enable] [Auto] 以下項目僅當 Enable AER Cap 設置為 [Auto] 或 [Enable] 時才會出現。 ACS Enable [Auto] 需啟用 AER 才能使 ACS 啟用並運行。設置值有:[Disable] [Enable] [Auto] PCIe ARI Support [Auto] 本項目可以啟用 Alternative Routing-ID Interpretation。設置值有:[Disable] [Enable] [Auto] PCIe ARI Enumeration [Auto] 允許每個下游端口的 ARI Forwarding。設置值有:[Disable] [Enable] [Auto] PCIe Ten Bit Tag Support [Auto] 本項目可以啟用 PCIe Ten B
以下項目僅當 Fan Table Control 設置為 [Manual] 時才會出現。 Low Temperature [0] 本項目可以 ℃ 為單位設置低溫。 Medium Temperature [0] 本項目可以 ℃ 為單位設置中間溫度。 High Temperature [0] 本項目可以 ℃ 為單位設置高溫。 Critical Temperature [0] 本項目可以 ℃ 為單位設置臨界溫度。 Low Pwm [0] 本項目可以在 0-100 間設置低 Pwm。 Medium Pwm [0] 本項目可以在 0-100 間設置中間 Pwm。 High Pwm [0] 本項目可以在 0-100 間設置高 Pwm。 Temperature Hysteresis [0] 本項目可以 ℃ 為單位設置溫度遲滯。 Pwm Frequency [25kHz] 設置值有:[100Hz] [25kHz] Fan Polarity [Negative] 設置值有:[Negative] [Positive] cTDP Control [Auto] [Auto] 使用融合 TDP。 [Manual] 可自訂 TD
Power Package Limit [280] 本項目可以自訂 PPT。 xGMI Link Width Control [Auto] [Auto] 使用默認 xGMI 鏈接寬度控制器設置。 [Manual] 可以自訂 xGMI 鏈接寬度控制器設置。 以下項目僅當 xGMI Link Width Control 設置為 [Manual] 時才會出現。 xGMI Force Link Width Control [Unforce] [Unforce] 不迫使 xGMI 至固定寬度。 [Force] 迫使 xGMI 至指定寬度。 以下項目僅當 xGMI Force Link Width Control 設置為 [Force] 時才會出 現。 xGMI Force Link Width [2] [0] 迫使 xGMI 鏈接寬度為 x2。 [1] 迫使 xGMI 鏈接寬度為 x8。 [2] 迫使 xGMI 鏈接寬度為 x16。 xGMI Max Link Width Control [Auto] [Auto] 使用默認最大 xGMI 支持鏈接寬度。 [Manual] 可自訂最
DLWM Support [Auto] 本項目可以啟用或關閉 DLWM 支持。設置值有:[Disabled] [Enabled] [Auto] Boost FmaxEn [Auto] [Auto] 使用默認 Fmax。 [Manual] 可設置啟動 Fmax。 以下項目僅當 Boost FmaxEn 設置為 [Manual] 時才會出現。 BoostFmax [0] 本項目可以用來指定 啟動 Fmax 頻率限制並套用至所有核心(MHz)。 EDC Current Tracking [Disable] 設置值有:[Disable] [Enable] 以下項目僅當 EDC Current Tracking 設置為 [Enable] 時才會出現。 EDC Tracking Current Threshold [0] 目前 AMP 的臨界值供 EDC Current Tracking 功能。 EDC Tracking Report Interval [1] 回報間隔。在 SMU 裡每 N 個觀察結果記錄為可修正 MCE。 LCLK Frequency Control Root Complex 0x
DF PState Mode Select [Auto] [Normal] 正常。 [Limit Highest] FCLK 受限於 DF Pstate FCLK Limit,僅使用最 高 DF Pstate。 [Limit All] FCLK 受限於 DF Pstate FCLK Limit,所有 DF Pstates 均使用。 [Auto] 自動 EDC Control [Auto] [Auto] 使用融合 VDDCR_CPU EDC 限制。 [Manual] 可自訂最大 VDDCR_CPU EDC 限制。 以下項目僅當 EDC Control 設置為 [Manual] 時才會出現。 EDC [0] 本項目可以設置 VDDCR_CPU EDC Limit [A]。 EDC Platform Limit [0] 本項目可以設置 EDC Platform Limit [W]。 NBIO RAS Common Options NBIO RAS Control [Auto] 設置值有:[Disabled] [MCA] [Legacy] [Auto] Egress Poiso
Uncorrected Converted to Poison Enable Mask High [30000] 本項目用以遮蔽內部陣列的不可修正奇偶校驗誤差。每個位元設置為 1 時,系 統致命錯誤事件將會觸發關聯出口端口上的陣列 UCP 錯誤。每個位元設置為 0 時,錯誤將被遮蔽。 Uncorrected Converted to Poison Enable Mask Low [4] 本項目用以遮蔽內部陣列的不可修正奇偶校驗誤差。每個位元設置為 1 時,系 統致命錯誤事件將會觸發關聯出口端口上的陣列 UCP 錯誤。每個位元設置為 0 時,錯誤將被遮蔽。 System Hub Watchdog Timer [A28] 此數值可以毫秒為單位指定 SYSHUB Watchdog Timer 的時間間隔。 SLink Read Response OK [Disabled] 此數值可以指定 S L I N K 讀取回應錯誤是否轉換為 O k a y 回應。設置值有: [Disabled] [Enabled] SLink Read Response Error Handling [Log Errors in M
Presence Detect Select mode [Auto] 本項目可以用來控制 Presence Detect 選擇模式。設置值有:[OR] [AND] [Auto] Preferred IO [Auto] 本項目可以選擇偏好的 IO 選擇類型。設置值有:[Bus] [Auto] Data Link Feature Cap [Auto] 本項目可以設置 Data Link Feature Capability。設置值有:[Enabled] [Disabled] [Auto]] CV test [Auto] 將本項目設置為 [Enabled] 以支持運行 PCIECV 工具。選擇 [Auto] 會保留 h/w 默 認值。設置值有:[Auto] [Disabled] [Enabled] SEV-SNP Support [Disable] 設置值有:[Disabled] [Enabled] SRIS [Auto] 設置值有:[Auto] [Disable] [Enable] FCH Common Options SATA Configuration Optoins SATA Enable [A
DevSleep0 Port Number [0] 本項目可以設置 DEVSLP port 0。設置值有:[0] - [7] Aggressive SATA Device Sleep Port 1 [Auto] 設置值有:[Disabled] [Enabled] [Auto] 以下項目僅當 Aggressive SATA Device Sleep Port 1 設置為 [Enabled] 時才會出現。 DevSleep1 Port Number [0] 本項目可以設置 DEVSLP port 1。設置值有:[0] - [7] SATA Controller options SATA Controller Enable Sata0 Enable [Auto] 本項目可以啟用或關閉 Sata0。每個 IOD 有 4 Sata 控制器。設置值有: [Disabled] [Enabled] [Auto] Sata1 Enable [Auto] 本項目可以啟用或關閉 Sata1。每個 IOD 有 4 Sata 控制器。設置值有: [Disabled] [Enabled] [Auto] Sata2 Enable [
以下項目僅當 Socket1 DevSlp0 Enable 設置為 [Enabled] 時才會出現。 DevSleep0 Port Number [0] 本項目可以設置 DEVSLP port 0。設置值有:[0] - [7] Socket1 DevSlp1 Enable [Auto] 僅每個 I O D/s o c k e t 的 S a t a0 支持 D e v S l p。設置值有:[D i s a b l e d] [Enabled] [Auto] 以下項目僅當 Socket1 DevSlp1 Enable 設置為 [Enabled] 時才會出現。 DevSleep0 Port Number [1] 本項目可以設置 DEVSLP port 1。設置值有:[0] - [7] SATA Controller SGPIO Sata0 SGPIO [Auto] 本項目可以啟用或關閉 S a t a0 的 S a t a S g p i o。設置值有:[D i s a b l e d] [Enabled] [Auto] Sata1 SGPIO [Auto] 本項目可以啟用或關閉 S a t a1 的 S a
Sata7 SGPIO [Auto] 本項目可以啟用或關閉 S a t a7 的 S a t a S g p i o。設置值有:[D i s a b l e d] [Enabled] [Auto] USB Configuration Options XHCI Controller0 enable [Auto] 本項目可以啟用或關閉 USB3 控制器。設置值有:[Enabled] [Disabled] [Auto] XHCI Controller1 enable [Auto] 本項目可以啟用或關閉 USB3 控制器。設置值有:[Enabled] [Disabled] [Auto] USB ecc SMI Enable [Auto] MCM USB enable XHCI2 enable (Socket1) [Auto] 本項目可以啟用或關閉 USB3 控制器。設置值有:[Disabled] [Enabled] [Auto] XHCI3 enable (Socket1) [Auto] 本項目可以啟用或關閉 USB3 控制器。設置值有:[Disabled] [Enabled] [Auto] SD Dump
Uart Configuration Options Uart 0 Enable [Auto] Uart 0 無任何 Uart 2 啟用的 HW FC。設置值有:[Disabled] [Enabled] [Auto] 以下項目僅當 Uart 0 Enable 設置為 [Enabled] 時才會出現。 Uart 0 Legacy Options [Auto] 設置值有:[Disabled] [0x2E8] [0x2F8] [0x3E8] [0x3F8] [Auto] Uart 1 Enable [Auto] Uart 1 無任何 Uart 3 啟用的 HW FC。設置值有:[Disabled] [Enabled] [Auto] 以下項目僅當 Uart 1 Enable 設置為 [Enabled] 時才會出現。 Uart 1 Legacy Options [Auto] 設置值有:[Disabled] [0x2E8] [0x2F8] [0x3E8] [0x3F8] [Auto] Uart 2 Enable (no HW FC) [Auto] 設置值有:[Disabled] [Enabled] [Auto]
Miscellaneous Options Boot Timer Enable [Auto] [Disabled] 迫使 PMx44 bit 27 = 1。 [Enabled] 迫使 PMx44 bit 27 = 0。 [Auto] PMx44 bit 27 = PcdBootTimerEnable。 NTB Common Options Socket-0 P0 NTB Enable [Auto] 本項目可以啟用 NTB on Socket-0 P0 Link。設置值有:[Auto] [Enable] 以下項目僅當 Socket-0 P0 NTB Enable 設置為 [Enabled] 時才會出現。 Socket-0 P0 Start Lane [0] 本項目可以設置 NTB Start Lane on Socket-0 P0 Link。設置值有:[0] - [15] Socket-0 P0 End Lane [15] 本項目可以設置 NTB End Lane on Socket-0 P0 Link。設置值有:[0] - [15] Socket-0 P0 Link Speed [Auto]
Socket-0 P1 End Lane [47] 本項目可以設置 NTB End Lane on Socket-0 P1 Link。設置值有:[32] - [47] Socket-0 P1 Link Speed [Auto] 本項目可以選擇 Link Speed for Socket-0 P1。設置值有:[Max Speed] [Gen 1] [Gen 2] [Gen 3] [Auto] [Gen 4] Socket-0 P1 NTB Mode [Auto] 本項目可以選擇 NTB Mode for Socket-0 P1 Link。設置值有:[Auto] [NTB Disabled] [NTB Primary] [NTB Secondary] Socket-0 P2 NTB Enable [Auto] 本項目可以啟用 NTB on Socket-0 P2 Link。設置值有:[Auto] [Enable] 以下項目僅當 Socket-0 P2 NTB Enable 設置為 [Enabled] 時才會出現。 Socket-0 P2 Start Lane [80] 本項目可以設置 NTB Start
Socket-0 P3 Link Speed [Auto] 本項目可以選擇 Link Speed for Socket-0 P3。設置值有:[Max Speed] [Gen 1] [Gen 2] [Gen 3] [Auto] [Gen 4] Socket-0 P3 NTB Mode [Auto] 本項目可以選擇 NTB Mode for Socket-0 P3 Link。設置值有:[Auto] [NTB Disabled] [NTB Primary] [NTB Secondary] Soc Miscellaneous Control ABL Console Out Control [Auto] [Disable] 關閉 ABL Console Out Control。 [Enable] 啟用 ABL Console Out Control。 [Auto] 維持默認值。 以下項目僅當 ABL Console Out Control 設置為 [Enable] 時才會出現。 ABL Basic Console Out Control [Auto] [Disable] 關閉 ABL Basic Co
Workload Tuning Workload Profile [Auto] 本項目可以選擇不同的工作量設置文件。 [Disabled] 不使用任何工作量設置文件。 [CPU Intensive] 調整為 CPU 密集工作量。 [Java Throughput] 將 Java 工作量調整為最高等級流通量。 [Java Latency] 調整為延遲敏感 Java 工作量。 [Power Efficiency] 調整為最佳功率效率。 [Memory Throughput Intensive] 調整為最高內存流通量。 [Storage IO Intensive] 調整最高存儲 IO 帶寬。 [NIC Throughput Intensive] 調整為最大 T C P/I P 與 R D M A 網絡流通 量。 [NIC Latency Intensive] 調整校心運行 L3 封包的網絡性能。 [Accelerator Throughput] 利用加速器,如 GPU 調整為對等網絡 PCIe 流通量。 [VMware vSpher
5.5.5 APM Restore AC Power Loss [Last State] 若設置為 [Power Off],則當系統在電源中斷之後電源將維持關閉狀態。若設置為 [Power On],當系統在電源中斷之後重新開啟。若設置為 [Last State],會將系統設 置恢復到電源未中斷之前的狀態。設置值有:[Power Off] [Power On] [Last State] Power On By PCI-E [Disabled] [Disabled] 關閉 PCIE 設備引起的喚醒事件。 [Enabled] 啟用 PCIE 設備引起的喚醒事件。 Power On By RTC [Disabled] [Disabled] 關閉 RTC 引起的喚醒事件。 [Enabled] 當設置為 [Eanbled] 時,RTC Alarm Date (Days) 與 Hour/Minute/ Second 選項則可以讓用戶自行設置想要的數值。 5.5.
以下項目只有在 LAN Enable 設置為 [JumperState] 時才會出現。 ROM Type [Disabled] 提供您選擇 Intel LAN ROM(Intel 網絡隨選只讀內存)類型。設置值有: [Disabled] [PXE] [iSCSI] 5.5.
Bits per second [115200] 提供您選擇串口傳輸速度,這速度必須與另一邊符合,過長或過多都可能會導 致速度變慢。設置值有:[9600] [19200] [38400] [57600] [115200] Data Bits [8] 設置值有:[7] [8] Parity [None] 一個 parity(同位)位能發送數據位來檢測一些傳輸錯誤,[Mark] 與 [Space] parity 則不允許錯誤檢測。 [None] None。 [Even] 同位位為 0,表示 N 個位裡,1 出現的總次數為偶數。 [Odd] 同位位為 0,表示 N 個位裡,1 出現的總次數為奇數。 [Mark] 同位位總是 1。 [Space] 同位位總是 0。 Stop Bits [1] Stop bits 為串行數據封包的終點(開始位表示起始)。標準設置是 1 Stop bit。使用較慢的設備通信可能會需要超過 1 stop bit。設置值有:[1] [2] Flow Control [None] F l o w c o n t r o l(流量控制)能預防在緩衝區溢滿時的數據流失。當
Legacy Console Redirection Settings Legacy Console Redirection Port [COM1] 可讓您選擇一個 COM 連接端口以顯示 Legacy 操作系統與 Legacy OPROM 信息 的重新導向。設置值有:[COM1] [COM2] Legacy OS Redirction Resolution [80x24] 設置支持舊有操作系統的行、列數。設置值有:[80x24] [80x25] Redirection After BIOS POST [Always Enable] 當 Bootloader 已被選擇超過常規控制面板轉向,則允許您設置本項。設置值 有:[Always Enable] [Bootloader] S e r i a l P o r t f o r O u t-o f-B a n d M a n a g e m e n t/W i n d o w s E m e r g e n c y Management Services (EMS) Settings COM2 Console Redirection [Disabled]
5.5.8 CPU 設置 本菜單顯示 CPU 節點信息。 SVM Mode [Enabled] 本項目用來啟動或關閉 SVM 模式。設置值有:[Disabled] [Enabled] Node 0 Information 本項目用來顯示 Node 0 信息。 5.5.
5.5.
5.5.
5.5.
5.5.
5.5.14 SATA 設置 本菜單提供 SATA 控制器及驅動程序信息。 5.5.
5.
SATA Partial State Capability [Enabled] 指示 HBA 是否支持轉換為局部狀態。設置值有:[Disabled] [Enabled] SATA FIS Based Switching [Enabled] 指示 H B A 是否支持端口倍增器 F I S-b a s e d s w i t c h i n g。設置值有: [Disabled] [Enabled] SATA Command Completion Coalescing Support [Disabled] 指示 HBA 是否支持 Command Completion Coalescing。設置值有: [Disabled] [Enabled] SATA Slumber State Capability [Enabled] 指示 HBA 是否支持轉換為睡眠狀態。設置值有:[Disabled] [Enabled] SATA Target Support 8 Devices [Disabled] 指示 SATA 目標裝置是否支持 8 個裝置。設置值有:[Disabled] [Enabled] Generic Mode [
5.7 安全性菜單(Security menu) 本菜單可以讓您更改系統安全設置,並且提供您啟用或關閉安全啟動(S e c u r e Boot)狀態與讓用戶設置系統模式(System Mode)狀態。 Administrator Password(設置系統管理員密碼) 請依照以下步驟設置系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 C r e a t e N e w P a s s w o r d 窗口輸入欲設置的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟更改系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3. 由 Create New Password 窗口輸入新密碼,輸入完成按下 。 4.
User Password(設置用戶密碼) 請依照以下步驟設置用戶密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 C r e a t e N e w P a s s w o r d 窗口輸入欲設置的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟更改用戶密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3. 由 Create New Password 窗口輸入新密碼,輸入完成按下 。 4. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟刪除用戶密碼(User Password): 1. 請選擇 Clear User Password 項目並按下 。 2.
Restore Factory Keys 此項目將強迫系統進入 User Mode,並安裝出廠默認安全啟動金鑰數據。 Reset to Setup Mode 此項目將會刪除 NVRAM 中的所有啟動金鑰數據。 Key Management 本項目僅當 S e c u r e B o o t M o d e 設置為 [C u s t o m] 時才會顯示,提供您修改 Secure Boot(安全啟動)變量與設置 Key Management(密鑰管理)頁面。 Factory Key Provision [Disabled] 本項目可以在系統為 Setup Mode 時提供您系統默認安全啟動變量。設置值 有:[Disabled] [Enabled] Restore Factory keys 本項目會安裝所有系統默認安全變量。 Reset to Setup Mode 本項目僅當您設置原廠默認金鑰時才會出現。本項目可以讓您刪除所有金鑰恢 復 Setup Mode。 Export Secure Boot Variables 本項目會詢問您是否要保存所有安全啟動變量。選擇 Yes 以保存,或是選擇 No 放棄
Device Guard Ready Remove‘UEFI CA’from DB 由 Secure Boot DB 刪除 Microsoft UEFI CA。 Restore DB defaults 將 DB variable 恢復為出廠默認值。 Platform Key (PK) 設置值有:[Details] [Export] [Update] [Delete] Key Exchange Keys (KEK) / Authorized Signatures (DB) / Forbidden Signatures (DBX) 設置值有:[Details] [Export] [Update] [Append] [Delete] Authorized TimeStamps (DBT) / OsRecovery Signatures 設置值有:[Update] [Append] 華碩 RS500A-E11 系列用戶手冊 5-61
5.
5.
5.10 事件記錄菜單(Event Logs menu) 5.10.
以下的項目僅當 Smbios Event Log 設置為 [Enabled] 時才會出現。 Erasing Settings Erase Event Log [No] 本項目提供選擇清除 Smbios Event Log 的選項,在重新啟動時清除在任何載入任 何記錄動作。設置值有:[No] [Yes, Next reset] [Yes, Every reset] When Log is Full [Do Nothing] 本項目用來設置記錄滿載時的動作。設置值有:[Do Nothing] [Erase Immediately] Custom Options Log EFI Status Code [Enabled] 允許您開啟或關閉 EFI 狀態編碼記錄。設置值有:[Disabled] [Enabled] 以下的項目僅當 Log EFI Status Code 項目設置為 [Enabled] 時才會出 現。 Convert EFI Status Codes to Standard Smbios Type [Disabled] 允許您開啟或關閉 EFI 狀態編碼轉變為標準 Smbios 編碼(不是所有都
5.
5.11.
5.11.
Configure IPV6 support DM_LAN1 / Shared LAN IPV6 support 本項目用來開啟或關閉 IPV6 支持。設置值有:[Enabled] [Disabled] 僅當 IPV6 support 項目設為 [Enabled] 時,以下項目才會出現。 Configuration Address source [Previous State] 選擇設置的網絡通道的參數為靜態或動態。設置值有:[Previous State] [Static] [DynamicBmcDhcp] 僅當 Configuration Address source 項目設為 [Static] 時,以下項目才會 出現。 Station IPV6 address 本項目用來設置 IPV6 地址。 Prefix Length 本項目可以設置前置位長度(最多為 128)。 Configuration Router LAN1 Address 選擇設置的網絡通道的參數為靜態或動態。設置值有:[Previous State] [Static] [DynamicBmcDhcp] 僅當 Configurati
僅當 IPV6 support 項目設為 [Enabled] 時,以下項目才會出現。 Configuration Address source [Previous State] 選擇設置的網絡通道的參數為靜態或動態。設置值有:[Previous State] [Static] [DynamicBmcDhcp] Station IPV6 address 本項目用來設置 IPV6 地址。 Prefix Length 本項目可以設置前置位長度(最多為 128)。 Configuration Router LAN2 Address 選擇設置的網絡通道的參數為靜態或動態。設置值有:[Previous State] [Static] [DynamicBmcDhcp] 僅當 Configuration Router LAN2 Address 項目設為 [Static] 時,以下項 目才會出現。 IPV6 Router1 IP Address 本項目可以設置 IPV6 Router1 IP 地址。 IPV6 Router1 Prefix Length Lan2 本項目可以設置 IPV6 路由器前置位長度(最多為
5.11.
5.
安裝驅動程序 在本章節中將介紹服務器內的相關驅動程序的安裝與設 置說明。 6
6.1 安裝應用程序與工具程序 本驅動及應用程序光盤裡提供您主板相關的驅動程序、管理應用程序與工具程序, 可以讓您將主板功能最佳化。 1. 驅動及應用程序 DVD 光盤裡的內容如有更改,恕不另行通知。請訪 問華碩網站(w3.asus.com.cn)以更新最新的軟件與工具程序。 2. 驅動及應用程序 DVD 光盤為支持使用於 Windows® Server 2012 R2 和 Windows® Server 2016 操作系統。 在驅動及應用程序 DVD 光盤的主菜單裡有以下幾個標籤頁: 1. Drivers - 驅動程序主菜單提供了您當前需要安裝的一些硬件驅動程序。 2. Utilities - 工具軟件菜單顯示了可安裝於此系統的應用軟件與工具。 3. Manual - 用戶手冊菜單提供您用戶手冊的開啟鏈接。 您需要在操作系統中使用網絡瀏覽器軟件才能開啟用戶手冊。 4.
附錄 本附錄為提供您參考的相關聯絡信息。
KMPA-U16 架構圖
服務與支持 請訪問 https://www.asus.com.