User Manual
Table Of Contents
- 目录
- 使用注意事项
- 用电安全
- 关于本用户手册
- 第一章:系统导览
- 第二章:硬件安装
- 第三章:主板信息
- 第四章:BIOS 程序设置
- 4.1 管理、更新您的 BIOS 程序
- 4.2 BIOS 程序设置
- 4.3 主菜单(Main)
- 4.4 性能调整菜单(Performance Tuning menu)
- 4.5 高级菜单(Advanced menu)
- 4.5.1 可信任计算(Trusted Computing)
- 4.5.2 Redfish Host 介面设置(Redfish Host Interface Settings)
- 4.5.3 AMD CBS
- 4.5.4 内置网络设置(Onboard LAN Configuration)
- 4.5.5 串口控制面板重新定向(Serial Port Console Redirection)
- 4.5.6 CPU 设置(CPU Configuration)
- 4.5.7 PCI 子系统设置(PCI Subsystem Settings)
- 4.5.8 USB 设置(USB Configuration)
- 4.5.9 网络协定堆栈设置(Network Stack Configuration)
- 4.5.10 NVMe 设置(NVMe Configuration)
- 4.5.11 SATA 设置(SATA Configuration)
- 4.5.12 OffBoard SATA 控制器设置
- 4.5.13 APM 设置(APM Configuration)
- 4.5.14 AMD 内存设置状态(AMD Mem Configuration Status)
- 4.5.15 T1s Auth
- 4.5.16 驱动程序状态(Driver Health)
- 4.5.17 第三方 UEFI 驱动程序设置
- 4.6 芯片菜单(Chipset menu)
- 4.7 安全性菜单(Security menu)
- 4.8 启动菜单(Boot menu)
- 4.9 工具菜单(Tool menu)
- 4.10 事件记录菜单(Event Logs menu)
- 4.11 服务器管理菜单(Server Mgmt menu)
- 4.12 退出 BIOS 程序(Exit menu)
- 附录
第四章:BIOS 程序設置
4-16
以下項目只有在 Enable AER Cap 設為 [Enabled] 或 [Auto] 時才會出
現。
ACS Enable [Auto]
設置值有:[Disabled] [Enabled] [Auto]
PCIe ARI Support [Auto]
設置值有:[Disabled] [Enabled] [Auto]
PCIe ARI Enumeration [Auto]
允許每個下游端口的 ARI Forwarding。
設置值有:[Disabled] [Enabled] [Auto]
PCIe Ten Bit Tag Support [Auto]
本項目可以啟用 PCIe Ten Bit Tag 支持。當本項目設為 [Auto] 時會關閉支
持。
設置值有:[Disabled] [Enabled] [Auto]
SMU Common Options
本項目用來設置 SMU Common options。
NBIO RAS Common Options
本項目用來設置 NBIO RAS Common options。
Enable AER Cap [Auto]
設置值有:[Disabled] [Enabled] [Auto]
Early Link Speed [Auto]
設置值有:[Auto] [Gen1] [Gen2]
Hot Plug Handling Mode [Auto]
設置值有:[OS First] [Firmware First/EDR if OS supports]
[Firmware First but allow OS first] [System Firmware Intermediary] [Auto]
Hot Plug Allow FF in Synchronous [Disabled]
允許固件先在熱插換處理模式運行模式 A 與 模式 B 同步映射。
設置值有:[Disabled] [Enabled]
Presence Detect Select Mode [Auto]
設置值有:[OR] [AND] [Auto]
Data Link Feature Cap [Auto]
設置值有:[Disabled] [Enabled] [Auto]
CV Test [Auto]
本項目用來開啟或關閉支持 PCIECV 工具。當本項目設為 Auto 時表示保留硬
件默認值。
設置值有:[Disabled] [Enabled] [Auto]
SEV-SNP Support [Disabled]
設置值有:[Disabled] [Enabled] [Auto]