User Manual
Table Of Contents
- 目录
- 使用注意事项
- 用电安全
- 关于本用户手册
- 第一章:系统导览
- 第二章:硬件安装
- 第三章:主板信息
- 第四章:BIOS 程序设置
- 4.1 管理、更新您的 BIOS 程序
- 4.2 BIOS 程序设置
- 4.3 主菜单(Main)
- 4.4 性能调整菜单(Performance Tuning menu)
- 4.5 高级菜单(Advanced menu)
- 4.5.1 可信任计算(Trusted Computing)
- 4.5.2 Redfish Host 介面设置(Redfish Host Interface Settings)
- 4.5.3 AMD CBS
- 4.5.4 内置网络设置(Onboard LAN Configuration)
- 4.5.5 串口控制面板重新定向(Serial Port Console Redirection)
- 4.5.6 CPU 设置(CPU Configuration)
- 4.5.7 PCI 子系统设置(PCI Subsystem Settings)
- 4.5.8 USB 设置(USB Configuration)
- 4.5.9 网络协定堆栈设置(Network Stack Configuration)
- 4.5.10 NVMe 设置(NVMe Configuration)
- 4.5.11 SATA 设置(SATA Configuration)
- 4.5.12 OffBoard SATA 控制器设置
- 4.5.13 APM 设置(APM Configuration)
- 4.5.14 AMD 内存设置状态(AMD Mem Configuration Status)
- 4.5.15 T1s Auth
- 4.5.16 驱动程序状态(Driver Health)
- 4.5.17 第三方 UEFI 驱动程序设置
- 4.6 芯片菜单(Chipset menu)
- 4.7 安全性菜单(Security menu)
- 4.8 启动菜单(Boot menu)
- 4.9 工具菜单(Tool menu)
- 4.10 事件记录菜单(Event Logs menu)
- 4.11 服务器管理菜单(Server Mgmt menu)
- 4.12 退出 BIOS 程序(Exit menu)
- 附录
第四章:BIOS 程序設置
4-18
FCH RAS Options
本項目用來設置 FCH RAS。
Miscellaneous Options
本項目用來設置 FCH 選項。
NTB Common Options
Socket-0 P0 NTB Enable [Auto]
設置值有:[Disabled] [Enabled] [Auto]
Socket-0 P2 NTB Enable [Auto]
設置值有:[Disabled] [Enabled] [Auto]
Socket-0 G0 NTB Enable [Auto]
設置值有:[Disabled] [Enabled] [Auto]
Socket-0 G2 NTB Enable [Auto]
設置值有:[Disabled] [Enabled] [Auto]
Soc Miscellaneous Control
ABL Console Out Control [Auto]
[Disabled] 關閉 ABL ConsoleOut 功能。
[Enabled] 啟用 ABL ConsoleOut 功能。
[Auto] 維持默認值。
以下的項目只有在 ABL Console Out Control 設為 [Enabled] 時才會出
現。
ABL Console Out Serial Port [Auto]
[eSPI UART] 經由 eSPI UART 啟用串口。
[SOC UART0] 經由 SOC UART0 啟用串口。
[SOC UART1] 經由 SOC UART1 啟用串口。
[Auto] 使用默認值。
以下的項目只有在 ABL Console Out Serial Port 設為 [eSPI UART] 時才
會出現。
ABL Console Out Serial Port [Auto]
選擇 Legacy Uart(SIO or eSPI)IO base。
設置值有:[0x3F8] [0x2F8] [0x3E8] [0x2E8] [Auto]
ABL Basic Console Out Control
[Disabled] 關閉 ABL Basic ConsoleOut 功能。
[Enabled] 關閉 ABL Basic ConsoleOut 功能。
[Auto] 維持默認值。
ABL PMU message Control
本項目可以控制 PMU 除錯信息的數量。設置值有:[Detailed debug
message] [Coarse debug message] [Stage completion] [Assertion
messages] [Firmware completion message only] [Auto]