User Manual

華碩 RS500A-E12-RS4U 用戶手冊
1-15
（表格續下頁）
ACTION PHASE POST CODE TYPE DESCRIPTION
PSP Boot
PSP Boot Loader
phase (Status Post
Codes)
0x7D error
Bootloader detects BIOS request boot from SPI-ROM, which is unsupported
for PSB.
0x7E error Requested fuse is already blown, reblow will cause ASIC malfunction
0x7F error Error with actual fusing operation
0x80 error (Local Master PSP on P1 socket) Error reading fuse info
0x81 error
(Local Master PSP on P1 socket) Platform Vendor ID and/or Model ID binding
violation
0x82 error
(Local Master PSP on P1 socket) Requested fuse is already blown, reblow will
cause ASIC malfunction
0x83 error (Local Master PSP on P1 socket) Error with actual fusing operation
0x84 error SEV FW Rollback attempt is detected
0x85 error
SEV download FW command fail to broadcase and clear the IsInSRAM eld
on slave dies
0x86 error Agesa error injection failure
0x87 error Uncorrectable TWIX error detected
0x88 error Error programming the TWIX PCS registers
0x89
error Error setting TWIX PCS threshold value
0x8A error SW CCP queue is full, cannot add more entries
0x8B error CCP command description syntax error detected from input
0x8C error Return value stating that the command has not yet be scheduled
0x8D error The command is scheduled and being worked on
0x8E error The DXIO PHY SRAM Public key certicate loading or authentication fails
0x8F error
fTPM binary size exceeds limit allocated in Private DRAM, need to increase
the limit
0x90 error The TWIX link for a particular CCD is not trained Fatal error
0x91 error Security check failed (not all dies are in same security state)
0x92 error
FW type mismatch between the requested FW type and the FW type embedded
in the FW binary header
0x93 error SVC call input parameter address violation
0x94 error Firmware Compatibility Level mismatch
0x95 error Bad status returned by I2CKnollCheck
0x96 error NACK to general call (no device on Knoll I2C bus)
0x97 error Null pointer passed to I2CKnollCheck
0x98 error Invalid device-ID found during Knoll authentication
0x99 error Error during Knoll/Prom key derivation
0x9A error Null pointer passed to Crypto function
0x9B error Error in checksum from wrapped Knoll/Prom keys
0x9C error Knoll returned an invalid response to a command
0x9D error Bootloader failed in Knoll Send Command function
0x9E error No Knoll device found by verifying MAC
0x9F error The maximum allowable error post code
0xA0 error Bootloader successfully entered C Main
0xA1 error Master initialized C2P / slave waited for master to init C2P
0xA2 error HMAC key successfully derived
0xA3 error Master got Boot Mode and sent boot mode to all slaves
0xA4 error SpiRom successfully initialized
0xA5 error BIOS Directory successfully read from SPI to SRAM
0xA6 error Early unlock check
0xA7 error Inline Aes key successfully derived
0xA8 error Inline-AES key programming is done
0xA9 error Inline-AES key wrapper derivation is done
0xAA error Bootloader successfully loaded HW IP conguration values
0xAB error Bootloader successfully programmed MBAT table
0xAC error Bootloader successfully loaded SMU FW
0xAD error Progress code is available
0xAE error User mode test Uapp completed successfully
0xAF error Bootloader loaded Agesa0 from SpiRom
0xB0 error AGESA phase has completed
0xB1 error RunPostDramTrainingTests() completed successfully
0xB2 error SMU FW Successfully loaded to SMU Secure DRAM
0xB3 error Sent all required boot time messages to SMU
0xB4 error Validated and ran Security Gasket binary
0xB5 error UMC Keys generated and programmed
0xB6 error Inline AES key wrapper stored in DRAM
0xB7 error Completed FW Validation step
0xB8 error Completed FW Validation step
0xB9 error BIOS copy from SPI to DRAM complete
0xBA error Completed FW Validation step