RS500A-E9-PS4 RS500A-E9-RS4 RS500A-E9-RS4-U 伺服器 使用手冊
T15584 3.00 版 2019 年 6 月發行 版權說明 ©ASUSTeK Computer Inc. All rights reserved.
目錄 使用注意事項.................................................................................................................................... vi 用電安全............................................................................................................................................vii 電磁安全................................................................................................................................vii 靜電元件...............................................................................
目錄 2.8.1 系統風扇.................................................................................................................2-26 第三章:進階安裝 3.1 免工具標準式滑軌套件...................................................................................................... 3-2 3.2 滑軌套件規格......................................................................................................................... 3-5 第四章:主機板資訊 4.1 4.2 4.3 4.4 主機板構造圖................................................................................
目錄 5.4.14 USB 設定(USB Configuration)...............................................................5-22 5.4.15 iSCSI 設定...........................................................................................................5-23 5.5 晶片選單................................................................................................................................5-24 5.6 安全性選單(Security menu)......................................................................................5-25 5.7 開機選單(Boot menu).......
使用注意事項 操作伺服器之前請務必詳閱以下注意事項,避免因人為的疏失造成系統損傷甚至人 體本身的安全。 請勿使用非本產品配備的電源線,由於電路設計之不同,將有可能造成 內部零件的損壞。 ‧ 使用前,請檢查每一條連接線是否都已經依照使用手冊指示連接妥當,以及電源 線是否有任何破損,或是連接不正確的情形發生。如有任何破損情形,請儘速與 您的授權經銷商聯絡,更換良好的線路。 ‧ 伺服器安放的位置請遠離灰塵過多,溫度過高,太陽直射的地方。 ‧ 保持機器在乾燥的環境下使用,雨水、溼氣、液體等含有礦物質將會腐蝕電子線 路。 ‧ 使用伺服器時,務必保持周遭散熱空間,以利散熱。 ‧ 使用前,請檢查各項周邊設備是否都已經連接妥當再開機。 ‧ 避免邊吃東西邊使用伺服器,以免污染機件造成故障。 ‧ 請避免讓紙張碎片、螺絲及線頭等小東西靠近伺服器之連接器、插槽、孔位等 處,避免短路及接觸不良等情況發生。 ‧ 請勿將任何物品塞入伺服器機件內,以避免引起機件短路,或是電路損毀。 ‧ 伺服器開機一段時間之後,散熱片及部份IC表面可能會發熱、發燙,請勿用手觸 摸,並請檢查系統是否散熱不良。 ‧ 在安裝或是移除周邊產品時請先關閉電源。 ‧ 在
用電安全 電磁安全 ‧ 拆裝任何元件或是搬移伺服器之前,請先確定與其連接的所有電源都已經拔掉。 ‧ 拆裝任何元件上連接的訊號線之前,請先拔掉連接的電源線,或是先安裝訊號線 之後再安裝電源線。 ‧ 使用一隻手拆裝訊號線,以避免接觸到兩個不同電位表面造成不當的電流突波衝 擊產生。 ‧ 伺服器電源線請勿與其他事物機器共用同一個插座,儘量不要使用延長線,最好 能夠連接一台不斷電系統 UPS。 靜電元件 處理器、記憶體、主機板、介面卡、磁碟機、硬碟機等設備,是由許多精密的積體 電路與其它元件所構成,這些積體電路很容易因為遭受靜電的影響而損壞。因此,在 拆裝任何元件之前,請先做好以下的準備: ‧ 如果您有靜電環等防靜電設備,請先戴上。 ‧ 假如您所處的環境並沒有防靜電地板,開始拆裝伺服器之前,請您先將身體可能 帶的靜電消除。 ‧ 在尚未準備安裝前,請勿將元件由防靜電袋中取出。 ‧ 將元件由防靜電袋中取出時,請先將它與伺服器金屬平面部份碰觸,釋放靜電。 ‧ 拿持元件時儘可能不觸碰電路板,及有金屬接線的部份。 ‧ 請勿用手指接觸伺服器之連接器、IC 腳位、附加卡之金手指等地方。 ‧ 欲暫時置放元件時請放置在防靜電墊或是防靜
關於本使用手冊 本使用手冊主要是針對有經驗且具有個人電腦硬體組裝知識的使用者所撰寫的。本 手冊可以幫助您建立起最新、功能強大的華碩伺服器。手冊內容介紹本產品各部份元 件的拆裝、設定,因此,部份元件可能是選購配備,並未包含在您的產品當中,假如 您有需要選購該配備,請向本公司授權經銷商洽詢。 請勿將本主機板當作一般垃圾丟棄。本產品零組件設計為可回收利用。 這個打叉的垃圾桶標誌表示本產品(電器與電子設備)不應視為一般垃 圾丟棄,請依照您所在地區有關廢棄電子產品的處理方式處理。 請勿將內含汞的電池當作一般垃圾丟棄。這個打叉的垃圾桶標誌表示電 池不應視為一般垃圾丟棄。 章節說明 本使用手冊的內容結構如下: 第一章:系統導覽 本章以清楚的圖示帶您認識華碩 RS300-E10 系列伺服器的功能及特色,包括系統 的前、後面板以及內部功能的介紹。 第二章:硬體安裝 本章以逐步說明的方式,教您如何將系統所需的零組件正確地安裝至本伺服器裡 頭。 第三章:進階安裝 本章提供您本伺服器的機架安裝及使用方法。 第四章:主機板資訊 本章提供您有關本伺服器內建主機板的相關資訊,包括主機板的構造圖、J u m p e r 設定以及連接埠位
提示符號 以下為本手冊所使用到的各式符號說明: 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到主機板元件。不當的 動作可能會對產品造成損害。 注意:重點提示,重要的注意事項。您必須遵照使用手冊所描述之方式 完成一項或多項軟硬體的安裝或設定。 說明:小祕訣,名詞解釋,或是進一步的資訊說明。提供有助於完成某 項工作的訣竅和其他額外的資訊。 哪裡可以找到更多的產品資訊 您可以經由下面所提供的兩個管道來獲得您所使用的華碩產品資訊以及軟硬體的升 級資訊等。 1. 華碩網站 您可以到 http://tw.asus.com 華碩電腦全球資訊網,來取得所有關於華碩軟硬體產品 的各項資訊。 2.
產品之限用物質含有情況 「產品之限用物質含有情況」之相關資訊,請參考下表。 單元 鉛 (Pb) 汞 (Hg) 限用物質及其化學符號 六價鉻 鎘 (Cd) (Cr+6) 印刷電路板及其 o o o 電子組件 外殼 o o o o 散熱設備 o o o 電源供應器 o o o 其他及其配件 o o o 備考 1 "o" 係指該項限用物質之百分比含量未超出百分比含量基準值。 備考 2 "-" 係指該項限用物質為排除項目。 x 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) o o o o o o o o o o
第一章: 系統導覽 本章將介紹本伺服器的各項組成元件,其中包括系統的 前、後面板以及內部功能的總體介紹。 1
1.1 產品包裝內容 以下列本伺服器包裝內的組件。 標準元件 機種型號 RS500A-E9-PS4、RS500A-E9-RS4、RS500A-E9-RS4-U 機殼 華碩 R10E 1U 機架式機殼 主機板 華碩 KNPA-U16 伺服器主機板 硬體組件 1 x 650W 單一式電源供應器(RS500A-E9-PS4) 1 x 770W 備援式電源供應器(RS500A-E9-RS4,RS500A-E9RS4-U) 4 x 可熱抽換 3.5 吋硬碟抽取架 1 x SAS/SATA 3.5 吋硬碟背板(RS500A-E9-PS4,RS500A-E9RS4) 1 x SAS/SATA/NVMe 3.
1.
1.3 產品規格表 華碩 RS500A-E9 系列是一款精心打造的 1U 伺服器,內裝 KNPA-U16 伺服器主機 板,支援 AMD EPYC™ 7000 系列中央處理器,並包含最新內建於主機板上的晶片組 所提供的相關技術。 機種型號 RS500A-E9-PS4 RS500A-E9-RS4 支援中央處理器 / 系統匯流排 核心邏輯 Intel® C621 PCH 晶片組 總插槽數 16(每個 CPU 8 通道;每個 CPU 2 個記憶體模組) 擴充容量 最高 2048GB 記憶體類型 DDR4 2666/2400/2133 RDIMM/LR-DIMM/LR-DIMM 3DS 記憶體 32GB、16GB、8GB、4GB(RDIMM) 64GB、32GB(LRDIMM) 128GB、64GB(LRDIMM 3DS) 單條記憶體大小 * 請參考華碩官方網站 tw.asus.
機種型號 RS500A-E9-PS4 RS500A-E9-RS4 輔 助 儲 存 裝 置 插 槽 ( 軟碟/光碟 機) 前端輸出 / 輸入連接埠 後側輸出 / 輸入連接埠 開關 / 指示燈 支援作業系統 軟體 管理解決方 外部遠端遙控硬 案 體 安裝認證標準 外觀尺寸(高 x 寬 x 深) 重量(不包含處理器、記憶體與 硬碟機) 重量(包含處理器、記憶體與硬 碟機) 電源供應器(視銷售區域而 定) 環境條件 RS500A-E9RS4-U 1 x 薄型光碟機插槽 (DVD-RW) 2 x USB 3.0 連接埠 1 x VGA 連接埠 2 x USB 3.
1.4 前端面板 本伺服器的前端面板提供了簡單的存取功能,包括電源按鈕、重置按鈕、 相關的 LED 指示燈及 USB 連接埠,可方便您隨時瞭解系統的狀況。 關於前面板 LED 指示燈的介紹,請參考 1.7.1 前面板指示燈 的說明。 機架螺絲 硬碟插槽 1 硬碟插槽 2 硬碟插槽 3 4 網路埠 4 指示燈 薄型光碟機(選配) Asset tag(財產標籤) 網路埠 3 指示燈 網路埠 2 指示燈 網路埠 1 指示燈 訊息指示燈 硬碟存取指示燈 1-6 第一章:系統導覽 3 2 機架螺絲 硬碟插槽 4 1 顯示器連接埠 USB 3.
1.5 後端面板 後端面板包含了所有連接裝置的接頭、後置風扇等。下圖即為伺服器後端面板圖 示。 RS500A-E9-RS4 / RS500A-E9-RS4-U 電源供應器與電源線連接孔 PCI-E 插槽 Q-Code 指示燈 iKVM 網路埠* USB 3.0 連接埠 Gigabit 網路埠 1(底部) 與 2(頂端) VGA 連接埠 Locate 指示燈 Message 指示燈 OCP 2.0 夾層卡插槽 電源按鈕 RS500A-E9-PS4 電源供應器與電源線連接孔 USB 3.0 連接埠 Gigabit 網路埠 1(底部) 與 2(頂端) VGA 連接埠 iKVM 網路埠* PCI-E 插槽 Q-Code 指示燈 Locate 指示燈 Message 指示燈 OCP 2.
1.6 內部組件 下圖即為本伺服器的標準內部組件: 1. 電源供應器與電源風扇 2. PCI 插槽轉接卡 3. ASUS KNPA-U16 伺服器主機 板 4. 系統風扇 5. SAS / SATA 背板(隱藏) 6. 硬碟插槽 1 - 連接至背板 7. 硬碟插槽 2 - 連接至背板 8. 硬碟插槽 3 - 連接至背板 9. 硬碟插槽 4 - 連接至背板 10. 前側 I/O 面板(隱藏) 11. 薄型光碟機 12.
1.7 LED 顯示燈號說明 1.7.
1.7.2 網路埠指示燈 網路埠指示燈 Activity/Link LED Speed LED 狀態 說明 狀態 說明 熄滅 綠燈 閃爍 未連接 已連接 存取資料中 綠燈 1 Gbps 連線 ACT/LINK SPEED LED LED 網路埠 專用管理網路埠(DM_LAN1)指示燈 Activity/Link LED Speed LED 狀態 說明 狀態 說明 熄滅 黃燈 閃爍 未連接 已連接 存取資料中 熄滅 橘燈 綠燈 10 Mbps 連線 100 Mbps 連線 1 Gbps 連線 ACT/LINK SPEED LED LED DM 網路埠 1.7.
第二章: 硬體安裝 本章節要告訴您如何安裝及移除本伺服器各個部分的組 件,以及在安裝過程中必需注意的事項。 2
2.1 機殼上蓋 2.1.1 打開機殼後半部上蓋 1. 鬆開機殼前半部上蓋側邊螺絲。 前半部上蓋側邊螺絲 2. 將機殼上蓋固定在機殼後端面板的二顆螺絲鬆開。 螺絲 3. 將機殼後半上蓋向後推,並使後半部 上蓋前緣與前半部上蓋保留約半吋距 離。 4. 接著就可以將後半上蓋從機殼上取 出。 5.
2.2 中央處理器(CPU) 本主機板具備 Socket SP3 處理器插槽,本插槽是專為 AMD EPYC™ 7000 系列處 理器所設計。 • 在您購買本主機板之後,請確認在處理器插座上附有一個 PnP 保護 蓋,並且插座接點沒有彎曲變形。若是保護蓋已經毀壞或是沒有保護 蓋,或者是插座接點已經彎曲,請立即與您的經銷商聯絡。 • 在安裝完主機板之後,請將隨插即用的保護蓋保留下來。只有在 LGA3647 插槽上附有隨插即用保護蓋的主機板符合 Return Merchandise Authorization(RMA)的要求,華碩電腦才能為您處理產品的維修與保 固。 • 本保固不包括處理器插座因遺失、錯誤的安裝或不正確的移除隨插即 用保護蓋所造成的毀損。 2.2.1 安裝中央處理器 請依照以下步驟安裝處理器: 1. 依照前面步驟移除後端上蓋板。 2.
3. 鬆開固定安裝盒上蓋的螺絲。 4. 輕輕向上掀起邊框。 安裝盒上蓋 邊框 外蓋 5.
6. 將裝有 C P U 的托架安裝至邊框 內,並移除保護蓋。 裝有 CPU 的托架只能以 單一方向正確地安裝到邊 框。切記請勿用力地將裝 有 CPU 的托架以錯誤的 方向進行安裝。 7. 裝有 CPU 的托架 外蓋 保護蓋 對齊 CPU 插槽蓋上邊框。 裝有 CPU 的托架 8.
9.
2.3 系統記憶體 2.3.1 概觀 本主機板配置有 16 個 DDR4 DIMM(Double Data Rate 4,雙倍資料傳輸率)記憶 體模組插槽。 下圖為 DDR4 DIMM 記憶體模組插槽在主機板上之位置。 2.3.
2.3.3 安裝記憶體模組 請依照下面步驟安裝記憶體模組: 1. 先將記憶體模組插槽固定卡榫扳 開。 2. 將記憶體模組的金手指對齊記憶 體模組插槽的溝槽,並且在方向 上要注意金手指的缺口要對準插 槽的凸起點。 記憶體模組缺口 插槽凸起點 往外扳開記憶體模 組插槽的卡榫 記憶體插槽上的凹槽為設計僅一個方向供記憶體模組插入,請在裝入 前,確定記憶體模組與記憶體插槽上的安裝方向是契合的。 3. 將記憶體模組插入插槽中,若無錯 誤,插槽的卡榫會因記憶體模組置 入而自動扣到記憶體模組的凹孔 中。 卡榫扣入 請將記憶體模組缺口對準插槽的凸起點並垂直插入,以免造成記憶體模 組缺口損壞。 ‧ 安裝二支或更多記憶體模組時,請參考主機板產品內附使用手冊上的 相關說明。 ‧ 請參閱華碩官網上關於合格記憶體廠商供應列表(QVL)的說明。 2.3.4 取出記憶體模組 請依照以下步驟取出記憶體模組: 1. 壓下記憶體模組插槽的固定卡榫以 鬆開記憶體模組。 2.
2.4 安裝硬碟機 本系統支援四個熱抽換 SATA/SAS 硬碟裝置。硬碟的安裝方式,是經由裝入連接 在主機板 SATA/SAS 背板上的模組式硬碟擴充槽來使用。 請按照以下的步驟來安裝 3.5 吋熱抽換 SATA/SAS 硬碟: 1. 請先將握把上的固定扣朝右方撥開(A),以便將硬碟槽握把鬆開(B)。 握把 2. 將握把朝左扳開時,硬碟槽便會 向外滑出,請順勢將硬碟擴充槽 往主機的前方抽離。 3. 將硬碟槽放置在平坦桌面上。 4.
5. 置入 3.5 吋硬碟機,再使用 4 顆螺 絲,將硬碟機鎖緊固定在硬碟槽內。 6. 當硬碟機安裝完畢後,請以手緊握住 硬碟槽握把置入系統的插槽中,將其 輕推至機殼底部。 當置入後,硬碟槽上的 SATA/SAS 接頭會完全與背板上的接孔契合。 7. 最後請將板手輕輕地推回原位並輕扣 固定,使硬碟槽能夠緊密地固定在機 殼中。 如果硬碟槽有正確地安裝, 您將會看到硬碟槽外緣與機 殼呈現切齊的狀態。 8.
請按照以下的步驟來安裝 2.5 吋硬碟: 1. 請先將握把上的固定扣朝右方撥開(A),以便將硬碟槽握把鬆開(B)。 握把 2. 將握把朝左扳開時,硬碟槽便會 向外滑出,請順勢將硬碟擴充槽 往主機的前方抽離。 3. 將硬碟槽放置在平坦桌面上。 4. 取出準備安裝的 2.
5. 置入 2.5 吋硬碟機,再使用 4 顆螺 絲,將硬碟機鎖緊固定在硬碟槽內。 6. 當硬碟機安裝完畢後,請以手緊握住 硬碟槽握把置入系統的插槽中,將其 輕推至機殼底部。 當置入後,硬碟槽上的 SATA/SAS 接頭會完全與背板上的接孔契合。 7. 最後請將板手輕輕地推回原位並輕扣 固定,使硬碟槽能夠緊密地固定在機 殼中。 如果硬碟槽有正確地安裝, 您將會看到硬碟槽外緣與機 殼呈現切齊的狀態。 8.
1 Q-Code 2.5 擴充插槽 2.5.1 安裝擴充卡至轉接卡支撐架 1 Q-Code 在 PCIE 插槽上已預先安裝一組轉接卡支撐架,請移除轉接卡支撐架以安裝 x8 或 x16 擴充卡。 請依照以下步驟,安裝 x8 或 x16 擴充卡: 1. 使用雙手握住轉接卡的兩端,再將 其從主機板的 PCI Express x24 插槽 中取出。 2. 將此轉接卡放置在平坦的桌面上, 接著請使用十字螺絲起子,將金屬 擋板上面的螺絲卸除。 3. 然後請將 PCI Express x8 或 x16 介 面卡插入轉接卡的插槽內。 4.
5. 將裝好介面卡的轉接卡,對準主機 板上的 PCI Express x24 插槽安裝。 5 2.5.2 安裝華碩 PIKE II 控制卡 您可以在內建的 PCI-E 插槽上安裝華碩 PIKE II 控制卡。 請依照以下步驟安裝華碩 PIKE II 控制卡: 1.
2. 移除固定金屬擋板與轉接卡支撐架的螺絲,然後取下金屬擋板。 3. 準備好你的華碩 PIKE II 控制卡。 4.
5. 從主機板取下預留的 mini-SAS HD 傳輸線。 6.
7.
2.5.3 安裝 M.2 擴充卡 您可以在主機板上提供的 M.2 插槽上面安裝一張 M.2 擴充卡。 請依照以下的步驟安裝 M.2 擴充卡: 1. 找到主機板上的 M.2(NGFF1)插槽位置,如下圖所示。 2. 使用螺絲起子將鎖在 M.2 插槽上的螺絲移除,並放置於一旁。 2. 移除主機板的頂端螺絲與基座螺 絲。 頂端螺絲 基座螺絲 3. 在主機板上為 M.
4. 將 M.2 卡準備好。 5. 將 M.2 卡對準並插入主機板上的 M.2 插槽。 確認 M.2 卡的金色接頭安裝至正確 位置以及 M.2 卡的螺絲孔與主機板 基座螺絲對齊。 6. 使用頂端螺絲將 M.2 卡鎖緊固定。 鎖緊固定之前請確認 M.
2.5.4 安裝夾層卡 請依照下列步驟安裝夾層卡: 1. 在主機板上找到夾層卡的位置。 2.
3. 選擇要安裝夾層卡的插槽,然後使 用螺絲起子將相關插槽撬開。 4. 準備好您的夾層卡與訊號線。將訊號傳輸端(白色)連接至卡上的 AUXLED_CON 接頭。 AUXLED_CON1 5.
6. 使用隨附的四顆螺絲將夾層卡鎖緊固定。 7. 將訊號端(黑色)連接至主機板上的 OCP_LED1 接頭。 訊號線兩端的尺寸與顏色不同以方便區分。請參考現有的傳輸線。 8.
2.5.5 設定擴充卡 安裝好擴充卡後,接著須藉由軟體設定來調整擴充卡的相關設定。 1. 啟動電腦,然後更改必要的 BIOS 程式設定。若需要的話,您也可以參閱第五章 BIOS 程式設定以獲得更多資訊。 2. 為加入的擴充卡指派一組尚未被系統使用到的 IRQ。請參閱下頁表中所列出的中 斷要求使用一覽表。 3.
2.
2.
2.8 移除系統組件 當您在安裝或移除系統裝置或是替換損壞的零組件時,或許需要移除先前所安裝的 系統組件。而本章節的內容就是要告訴大家如何移除與重新安裝下列各項系統組件。 安裝/移除系統組件之前,請先關閉系統電源。 2.8.1 系統風扇 請依照以下的步驟,移除系統風扇: 1. 將連接在背板上的系統風扇電源線全部拔除。 2. 將風扇取出然後置於一旁。 3. 重複步驟 1 至 2 移除其他系統風扇。 請依照以下的步驟,重新安裝系統風扇: 1. 將系統風扇置入風扇擴充槽中。請注意在置入時的風扇氣流箭頭方向是朝系統後 側面板。 2.
第三章: 進階安裝 本章節要告訴您,如何使用滑軌套件將本伺服器安裝至 機架中,以及在安裝過程中必須注意的事項。 3
3.1 免工具標準式滑軌套件 免工具的滑軌套件設計,提供您輕鬆將滑軌裝上機架並安裝伺服器至機架中,而無 須使用任何工具。這個套件並提供金屬止擋,可以讓您在安裝伺服器時提供額外的支 撐和穩定性。 免工具滑軌套件包含了以下組件: 螺絲組 固定閂 滑軌組件(包含螺絲) 固定閂螺絲 滑軌墊圈 滑軌螺絲 免工具滑軌 安裝免工具機架滑軌 請依照以下步驟,將免工具機架滑軌安裝至機架上: 1.
若您的伺服器機架深度超過 850mm,請依照步驟 2 至 4 安裝,若您的 伺服器機架深度在 850mm 以下,請跳過步驟 2 至 4 並從步驟 5 開始安 裝。 2. 小心拉出並拉伸右側滑軌,並準備好隨附的滑軌組件。 滑軌組件 3. 將滑軌組件對準右側機架滑軌並使用四顆隨附螺絲固定。 4. 依照步驟 2 至 3 將滑軌組件與左側機架滑軌固定。 5.
6. 使用隨附的螺絲將滑軌組件與滑軌固定。 7 8. 下壓彈簧鎖 ( ) 然後將螺栓插入已選定在機架上的方形安裝孔。 下壓滑軌另一端的彈簧鎖,然後插入已選定在機架上的方形安裝孔。如有必要, 請將機架滑軌拉長以便於安裝。 9. (如有必要) 使用隨附的滑軌螺絲與滑軌墊圈 ( ) 將滑軌與機架固定。 10. 接著請重複前面的步驟 3 至 5,安裝另一側的滑軌。 請確認安裝的機架滑軌(左和右)有平行一致,且安穩地固定在定位。 8.
3.2 滑軌套件規格 43.6mm 900mm 43.
3-6 第三章:進階安裝
第四章: 主機板資訊 在本章中要告訴您在安裝系統元件時所必須完成的主機 板安裝程序。詳細內容有:頻率開關設定、跳線選擇區設 定以及主機板的各種裝置接頭。 4
4.
主機板的各項元件 內部連接插槽 / 跳線選擇區 / 指示燈 頁碼 1. LAN controller settings (3-pin LAN_SW1-2) 4-5 2. LANNCSI setting (3-pin LANNCSI_SEL1) 4-7 3. Micro SD card slot (MSD1) 4-20 4. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) 4-7 5. Power Supply SMBus connector (5-pin PSUSMB1) 4-11 6. ATX power connectors (24-pin EATXPWR1, 8-pin EATX12V1) 4-14 7. CPU, front, and rear fan connectors (4-pin FRNT_FAN1-7, REAR_ FAN1-2) 4-13 8. USB 3.0 connector (20-1 pin USB3_34; 4-pin Type-A USB3_4) 4-12 9.
4.2 跳線選擇區 1. CMOS 組態資料清除(3-pin CLRTC1) 在主機板上的 CMOS 記憶體中記載著正確的時間與系統硬體組態等資料,這些 資料並不會因電腦電源的關閉而遺失資料與時間的正確性,因為這個 CMOS 的電 源是由主機板上的鋰電池所供應。想要清除這些資料,可以依照下列步驟進行。 您可以依照以下的步驟,清除 COMS RTC RAM 資料: 1. 關閉電腦電源,拔掉電源線。 2. 將 C L R T C 跳線帽由 [1-2](預設值)改為 [2-3] 約五∼十秒鐘(此時即清除 CMOS 資料),然後再將跳線帽改回 [1-2]。 3. 插上電源線,開啟電腦電源。 4.
2. VGA 控制器設定(3-pin VGA_SW1) 您可以透過本功能的設定來開啟或關閉主機板內建之 VGA 圖形顯示控制器功 能。預設值為開啟 [1-2] 。 3.
4. BMC 設定(3-pin BMC_EN1) 本跳線帽提供您啟用(預設)或關閉主機板內建的 BMC 控制器。 5. DMLAN 設定(3-pin DM_IP_SEL1) 本跳線帽提供您選擇 DMLAN 設定。設定為 [2-3] 以強制 DMLAN IP 使用固定 模式(IP=10.10.10.10, submask=255.255.255.
6. LANNCSI 設定(3-pin LANNCSI_SEL1) 此跳線帽可您選擇要啟用的 LAN NCSI。 7.
4.3 內建指示燈 1. 電力警示燈(SBPWR1) 當主機板上內置的電力指示燈亮著時,表示目前系統是處於正常運作、省電模 式或者軟關機的狀態中,並非完全斷電。這個警示燈可用來提醒您在置入或移除 任何的硬體裝置之前,都必須先移除電源,等待警示燈熄滅才可進行。請參考下 圖所示。 2.
3. Location 指示燈(LOCLED1) 當按下前面板上的 Location 按鈕時,這個指示燈會亮燈。這個內建的 LED 指 示燈功能就如同前面板 Location 指示燈一樣,提供您方便地找到在機殼裡指定的 伺服器模組的位置。 4.
5.
4.4 內部連接埠 1. Serial ATA 6.0Gbps 連接埠(7-pin SATA1-4) 這些連接埠由 AMD 整合式 SATA 控制器所控制,可支援使用細薄的 Serial ATA 訊號線連接 Serial ATA 硬碟(SATA 1 插槽預設為光碟機使用)。 實際的資料傳輸速度取決於所安裝的 Serial ATA 硬碟速度。 2.
3. USB 3.0 連接插槽(20-1 pin USB3_34; 4-pin Type-A USB3_4) 這個插槽用來連接 USB 3.0 模組,可在前面板或後側連接埠擴充 USB 3.0 模 組。當您安裝 USB 3.0 模組,您可以享受 USB 3.0 的益處,包括有更快的資料傳 輸率最高達 5Gbps、對可充電的 USB 裝置更快的充電速度、最佳化能源效率,以 及與 USB 2.0 向下相容。 4-pin 的 USB(Universal Serial Bus)Type-A 連接埠可 供連接 USB 3.0 裝置。 4.
5 CPU、前端與後端風扇電源插座(4-pin FRNT_FAN1-7, REAR_FAN1-2) 這些插座為支援連接冷卻風扇使用。將風扇電源線連接到主機板上的風扇插 座,請確認黑線需接到風扇電源插座上的接地端(G N D)。連接風扇電源插座 時,一定要注意到極性問題。 • 千萬要記得連接風扇的電源,若系統中缺乏足夠的風量來散熱,那麼 很容易因為主機內部溫度逐漸昇高而導致當機,甚至更嚴重者會燒毀 主機板上的電子元件。 • 注意:這些插座並不是跳線!不要將跳線帽套在它們的針腳上。 • 所有風扇都支援華碩智慧風扇轉速(Smart Fan)控制技術。 6.
7. TPM 排線插槽(20-1 pin TPM) 本插座支援安全性平台模組(TPM)系統,該系統可進行安全性儲存金鑰、數 位認證、密碼與資料。此外,TPM 系統也可協助增進網路安全,保護數位辨識功 能,並確保平台的整合性。 8. ATX 電源插座(24-pin EATXPWR1, 8-pin EATX12V1) 這個插座為提供給 A T X 電源使用。由電源所提供的連接插頭已經過特別設 計,只能以一個特定方向插入主機板上的電源插座。找到正確的插入方向後,僅 需穩穩地將之套進插座中即可。 • 請務必連接 24+8-pin 電源插座,否則系統將不會啟動。 • 若您想要安裝其他的硬體裝置,請務必使用較高功率的電源供應器以 提供足夠的裝置用電需求。若電源供應器無法提供裝置足夠的用電需 求,則系統將會變得不穩定或無法開機。 ‧ 本主機板支援 ATX2.
9.
10.
11. VGA 連接排針(10-1 pin VGA_HDR1) 這個排針支援 VGA 高動態範圍(High Dynamic-Range)介面。 12.
13. 機殼開啟警示連接排針(2-pin INTRUSION) 這組排針提供給設計有機殼開啟檢測功能的電腦主機機殼之用。此外,尚須搭 配一個外接式檢測裝置,譬如機殼開啟偵測感應器或者微型開關。在本功能啟用 時,若您有任何移動機殼元件的動作,感應器會隨即偵測到並且送出一信號到這 組接針,最後會由系統記錄下這次的機殼開啟事件。預設設定為 CASEOPEN 與 GND 接腳短路,此功能關閉。 14.
15. M.2(NGFF)插槽(NGFF1) 這個插槽用來安裝 M.2 (NGFF) SSD 模組。 這個插槽支援 M Key 與 2242/2260/2280/22110 類型 PCI-E 與 SATA儲 存裝置。 M.2(NGFF) SSD 模組為選配配備,請另行購買。 16.
17. OCP LAN Activity LED 連接埠 (4-1 pin OCP_LED1) OCP LAN LED 連接埠支援 OCP LAN 卡狀態指示燈。 18. Micro SD 記憶卡插槽(MSD1) 安裝 A S M B9 管理卡時,主機板支援 S D 記憶卡 v2.00(S D H C) / v3.
19. Mini-SAS HD 連接埠(ISATA1-2) 本主機板內建 mini Serial Attached SCSI(SAS)HD 連接埠,支援 Serial ATA。每個連接埠最多支援 4 個裝置。 20.
4-22 第四章:主機板資訊
第五章: BIOS 程式設定 BIOS 程式調校的優劣與否,和整個系統的運作效能有極 大的關係。針對自己的配備來作最佳化 BIOS 設定,可讓 您的系統性統再提升。本章節將逐一說明 BIOS 程式中的 每一項組態設定。 5
5.1 管理、更新您的 BIOS 程式 下列軟體讓您可以管理與更新主機板上的 BIOS 設定。 1. ASUS CrashFree BIOS 3 2. ASUS EzFlash 3. BUPDATER 當 BIOS 程式毀損時,使用可開機的 USB 隨身碟來更新 BIOS 程式。 使用 USB 隨身碟更新 BIOS。 使用可開機的 USB 隨身碟在 DOS 環境下更新 BIOS 程式。 上述軟體請參考相關章節的詳細使用說明。 建議您先將主機板原始的 BIOS 程式備份到可開機的 USB 隨身碟中, 以備您往後需要再度安裝原始的 BIOS 程式。使用華碩線上更新(ASUS Update)程式來拷貝主機板原始的 BIOS 程式。 5.1.
5.1.2 使用華碩 EzFlash 更新程式 華碩 EzFlash 程式讓您能輕鬆的更新 BIOS 程式,可以不必再透過開機片的冗長程 序或是到 DOS 模式下執行。 請至華碩網站 http://tw.asus.com 下載最新的 BIOS 程式檔案。 請依照下列步驟,使用 EzFlash 來更新 BIOS: 1. 將已存好最新版 BIOS 檔案的 USB 隨身碟插入 USB 連接埠。 2. 進入 BIOS 設定程式。來到 Tools 選單,選擇 ASUS EZ Flash Utility 後並按下 鍵將其開啟。 ASUS Tek.
5.1.3 BUPDATER 工具程式 以下的 BIOS 畫面僅供參考,請依您所見的實際 BIOS 畫面為準。 BUPDATER 工具程式可以提供您在 DOS 環境下,使用儲存有更新的 BIOS 檔案的 USB 隨身碟來更新 BIOS 檔案。 更新 BIOS 檔案 請依照以下的步驟,使用BUPDATER 工具程式來更新 BIOS 檔案: 1. 請先造訪華碩網站(tw.asus.com)下載最新主機板的 BIOS 檔案。並將檔案儲存 至可開機的 USB 隨身碟內。 2. 然後將華碩支援網站(support.asus.com)上的 BUPDATER 工具程式(BUPDATER. exe),下載並儲存至同一個可開機的 USB 隨身碟內。 3. 將系統開機至 DOS 環境下,然後使用鍵盤輸入指令: BUPDATER /i [filename].CAP [ filename] 這裡的意思就是輸入存放在 USB 隨身碟裡頭的最新或原本 BIOS 檔案名 稱,然後按 鍵。 A:\>BUPDATER /i[file name].
4. 程式會進行檢查檔案,然後開始更新 BIOS 檔案。 ASUS Tek. EzFlash Utility Current Platform Platform : KNPA-U16 Version : 0201 Build date: 12/04/2018 Start Programming Flash. New Platform Platform : KNPA-U16 Version : 0207 Build date: 01/05/2018 DO NOT SHUTDOWN THE SYSTEM!!! Write 75% 請勿在更新 BIOS 程式檔案時關閉或重新啟動系統,此舉將會導致系統損 毀! 5. 完成更新後,程式會回到 DOS 畫面,請重新啟動系統,透過硬碟開機。 The BIOS update is finished! Please restart your system. C:\> 華碩 RS500A-E9 系列使用手冊 5-5
5.2 BIOS 程式設定 主機板擁有一片可編輯的韌體晶片,您可以依照 5.
5.2.1 BIOS 程式選單介紹 功能表列 選單項目 設定值 一般說明 操作功能鍵 5.2.
5.2.3 選單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功能,則會顯 示 Main 選單的項目。 點選選單中的其他項目(如:Event Logs、Advanced、Monitor、Boot、Tool 與 Exit 等)也會出現該項目不同的選項。 5.2.4 子選單 在選單畫面中,若功能選項的前面有一個小三角形標記,代表此為子選單,您可以 利用方向鍵來選擇,並且按下 鍵來進入子選單。 5.2.5 操作功能鍵說明 在選單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改變各項功 能。 5.2.6 一般說明 在選單畫面的右上方為目前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動變更。 5.2.7 設定值 這些存在於選單中的設定值是提供給使用者選擇與設定之用。這些項目中,有的 功能選項僅為告知使用者目前運作狀態,並無法更改,那麼此類項目就會以淡灰色顯 示。而可更改的項目,當您使用方向鍵移動項目時,被選擇的項目以反白顯示,代表 這是可更改的項目。 5.2.
5.3 主選單(Main) 當您進入 BIOS 設定程式時,首先出現的第一個畫面即為主選單,內容如下圖。 5.3.1 System Date [Day xx/xx/xxxx] 設定您的系統日期。 5.3.
5.
5.4.1 Trusted Computing Configuration Security Device Support [Enabled] 可讓您啟動或關閉 BIOS 安全裝置支援功能。設定值有:[Disabled] [Enabled] 5.4.
5.4.
5.4.4 Smart Setting(智慧設定) SMART Self Test [Enabled] 提供您在 POST(開機自我測試)過程時,在所有硬碟上面執行 SMART Self Test (智慧型自我測試)。設定值有:[Disabled] [Enabled] 5.4.
5.4.
5.4.
Parity [None] 一個 p a r i t y(同位)位元能發送資料位元來檢測一些傳輸錯誤,[M a r k] 與 [Space] parity 則不允許錯誤檢測。 [None] None。 [Even] 同位位元為 0,表示 N 個位元裡,1 出現的總次數為偶數。 [Odd] 同位位元為 0,表示 N 個位元裡,1 出現的總次數為奇數。 [Mark] 同位位元總是 1。 [Space] 同位位元總是 0。 Stop Bits [1] Stop bits 為序列資料封包的終點(開始位元表示起始)。標準設定是 1 Stop bit。使用較慢的裝置通訊可能會需要超過 1 stop bit。設定值有:[1] [2] Flow Control [Hardware RTS/CTS] Flow control(流量控制)能預防在緩衝區溢滿時的資料流失。當傳送資料時, 若接收的緩衝區已經滿了,此時會送出“stop”(停止)訊號來停止傳送資料流 (data flow)。當緩衝區空出時,會再送出“start”(開始)訊號以重新開始傳 送資料流。硬體流量控制使用兩條金屬線來傳送 start/sto
Serial Port for Out-of-Band Management/Windows Emergency Management Services (EMS) Settings COM2 Console Redirection [Disabled] 啟用或關閉控制台轉向功能。設定值有: [Disabled] [Enabled] 當 Console Redirection 設定為 [Enabled] 時,以下的項目才會顯示。 Console Redirection Settings Out-of-Band Mgmt Port [COM1] 經由序列埠來遠端遙控管理 Windows Server 系統。設定值有:[COM1] [COM2] Terminal Type [VT-UTF8] 此為微軟 Windows Emergency Management Services (EMS) 提供 Windows Server 作業系統可以透過序列埠來採用遠端遙控管理。設定值有:V T100] [V T100+] [VT-UTF8] [ANSI] Bits per second [115200] 此為微軟 Wi
5.4.
5.4.
5.4.
5.4.12 NVMe 設定(NVMe Configuration) 本選單提供 NVMe 控制器及驅動程式資訊。 5.4.
5.4.
USB hardware delays and time-outs USB transfer time-out [20 sec] 本項目提供您暫停數值、提供控制、Bulk 與中斷傳輸。設定值有:[1 sec] [5 sec] [10 sec] [20 sec] Device reset time-out [20 sec] 本項目提供您選擇 USB 大量儲存裝置起始單元指令暫停時間。設定值有:[10 sec] [20 sec] [30 sec] [40 sec] Device power-up delay [Auto] 在做適當的自我回報給 Host Controller(主機控制器)之前,提供您在設定採用最 大時間值。設定值有:[Auto] [Manual] Mass Storage Devices AMI Virtual CDROM0-2 / Floppy / HDisk0 1.00 [Auto] 本項目提供您選擇大量儲存裝置的模擬類型。設定值有:[Auto] [Floppy] [Forced FDD] [Hard Disk] [CD-ROM] 5.4.
5.
5.6 安全性選單(Security menu) 本選單可以讓您變更系統安全設定,並且提供您啟用或關閉安全開機(S e c u r e Boot)狀態與讓使用者設定系統模式(System Mode)狀態。 Administrator Password(設定系統管理員密碼) 當您設定系統管理員密碼後,建議您先登入您的帳戶,以免 BIOS 設定程式中的某 些資訊無法檢視或變更設定。 請依照以下步驟設定系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟變更系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 視窗輸入密碼並按下 。 3.
User Password(設定使用者密碼) 當您設定使用者密碼後,你必需登入您的帳戶才能使用 BIOS 設定程式。使用者密 碼的預設值為 Not Installed,當您設定密碼後將顯示 Installed。 請依照以下步驟設定使用者密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Create New Password 視窗輸入欲設定的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟變更使用者密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Enter Current Password 視窗輸入密碼並按下 。 3. 由 Create New Password 視窗輸入新密碼,輸入完成按下 。 4.
Key Management 本項目僅當 Secure Boot Mode 設定為 [Custom] 時才會顯示,提供您修改 Secure Boot(安全開機)變量與設定 Key Management(密鑰管理)頁面。 Provision Factory Defaults [Disabled] 本項目可以在系統為 S e t u p M o d e 時提供您系統預設安全啟動變量。設定值 有:[Disabled] [Enabled] Install Factory Default keys 本項目會安裝所有系統預設安全變量。 Enroll Efi Image 本項目可以允許 Secure Boot mode 時執行 Efi Image。 Save All Secure Boot Variables 若您想要儲存所有安全變量,本項目將會進行詢問。選擇 Yes 進行儲存;或選 擇 No 取消。 Platform Key (PK) / Key Exchange Key (KEK) / Authorized Signatures (DB) / Forbidden Signatures (DBX) / Auth
5.
Floppy Drive BBS Priorities / Hard Drive BBS Priorities / CD/DVD ROM Drive BBS Priorities 只有當您連接了軟碟機 / SATA 光碟機或硬碟至 SATA 連接埠時,此項目才會出 現,用來設定 SATA 裝置的開機順序。 5.8 工具選單(Tool menu) 本工具選單可以讓您針對特別功能進行設定。請選擇選單中的選項並按下 鍵來顯示子選單。 IPMI HWM 本項目可以讓您執行 IPMI 硬體監控。 Start EZ Flash 當按下 鍵後,本項目可以讓您執行華碩 EZ Flash BIOS ROM 工具程式,請 參考 使用華碩 EZ Flash 更新 BIOS 程式 的說明。 5.
按下 鍵並不會立即離開 BIOS 程式,要從此選單上選擇適當的項 目,或按下 鍵才會離開 BIOS 程式。 Save Changes and Exit 本項目可讓您儲存變更,並離開 BIOS 程式。 Discard Changes and Exit 本項目可讓您放棄所做的變更,並離開 BIOS 程式。 Save Changes and Reset 本項目可讓您儲存變更後重置系統設定。 Discard Changes and Rest 本項目可讓您放棄所做的變更,並重置系統設定。 Restore Defaults 本項目提供您還原或載入所有選項的預設值。 Save as User Defaults 本項目可讓您將目前的設定值作為使用者預設值。 Restore as User Defaults 本項目可讓您還原或載入所有選項的使用者預設值。 Boot Override 這些項目會顯示可用的裝置。顯示在畫面中的裝置則是根據安裝在系統裡的裝置而 定,點選任一個項目可以設定該項目裡所列裝置的開機順序。 5-30 第五章:BIOS 程式設定
5.10 AMD CBS 選單 5.10.
5.10.2 DF Common Options Memory interleaving [Auto] 本項目可設定記憶體交插存取。設定值有:[None] [Channel] [Die] [Socket] [Auto] Memory interleaving size [Auto] 本項目可設定記憶體交插存取容量。設定值有:[256 Bytes] [512 Bytes] [1 KB] [2 KB] [Auto] 5.10.
Data Bus Configuration Data Bus Configuration User Controls [Auto] 本項目可開啟或關閉經由記憶體晶片選擇交插存取存儲區。設定值有: [Auto] [Manual] 以下的項目僅當 Data Bus Configuration User Controls 設定為 [Manual].
5.10.4 NBIO Common Options NB Configuration IOMMU [Enabled] 本項目可開啟或關閉 IOMMU。設定值有:[Disabled] [Enabled] [Auto] Concurrent Training [Auto] 本項目可以啟用或關閉同步訓練。設定值有:[False] [True] [Auto] NBIO Internal Poison Consumption [Auto] 本項目可以啟用或關閉 NBIO Internal Poison Consumption。設定值有:[Disabled] [Enabled] [Auto] NBIO RAS Control [Auto] 本項目可以啟用或關閉 NBIO RAS 控制。設定值有:[Disabled] [Enabled] [Auto] cTDP Control [Manual] 本項目可以設定 cTDP。設定值有:[Manual] [Auto] 以下的項目僅當 cTDP Control 設定為 [Manual].
PCIe ARI Support [Auto] 本項目可以啟用或關閉 PCIe ARI 支援。設定值有:[Disabled] [Enabled] [Auto] CLDO_VDDP Control [Auto] 本項目可以設定 CLDO_VDDP。設定值有:[Manual] [Auto] 以下的項目僅當 CLDO_VDDP Control 設定為 [Manual].
5.11 事件記錄選單(Event Logs menu) 5.11.
5.
BMC network configuration 在此子選單裡的項目可以提供您設定 BMC 區域網路參數。 View System Event Log 可以檢視系統事件記錄。 5-38 第五章:BIOS 程式設定
安裝驅動程式 在本章節中將介紹伺服器內的相關驅動程式的安裝與設 定說明。 6
6.1 安裝應用程式與工具程式 本驅動及公用程式光碟裡提供您主機板相關的驅動程式、管理應用程式與工具程 式,可以讓您將主機板功能最佳化。 1. 驅動及公用程式 DVD 光碟裡的內容如有變更,恕不另行通知。請造 訪華碩網站(tw.asus.com)以更新最新的軟體與工具程式。 2. 驅動及公用程式 DVD 光碟為支援使用於 Windows® Server 2012 R2 R2 和 Windows® Server 2016 作業系統。 6.2 使用驅動及公用程式 DVD 光碟 於光碟機中放入主機板/系統的驅動程式光碟。若您已經啟動光碟自動偵測的功 能,透過作業系統自動偵測的功能,接著會自行啟動光碟並顯示預設的 Drivers (驅 動程式)標籤頁。 若視窗並未自動出現,那麼請瀏覽驅動及公用程式 D V D 光碟的檔案內 容,找到 BIN 目錄中的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程 式來開啟選單畫面。 在驅動及公用程式 DVD 光碟的主選單裡有以下幾個標籤頁: 1. Drivers 2. Utilities 3. Manual 4.
6.2.1 驅動程式主選單 驅動程式主選單提供了您目前需要安裝的一些硬體驅動程式,請安裝必要的驅動程 式來啟動您系統上的硬體。 6.2.
6.2.3 使用手冊選單 您需要在作業系統中使用網路瀏覽器軟體才能開啟使用手冊。 6.2.
6.3 安裝 AMD 晶片裝置軟體驅動程式 本章節提供您如何安裝在 AMD 晶片環境中的隨插即用裝置元件。 您需要在 Windows® 作業系統環境中,手動安裝 AMD 晶片裝置軟體。 請依照以下步驟,在 Windows® 作業系統下安裝 AMD 晶片裝置軟體驅動程式: 1. 重新開機,並使用 Administrator(主管理者)登入作業系統。 2. 將驅動及公用程式 DVD 光碟放入光碟機中。 若您已經啟動光碟自動偵測的功能,透過作業系統自動偵測的功能,會自行啟動 光碟顯示 Drivers (驅動程式)選單畫面。 若視窗並未自動出現,那麼請瀏覽驅動及公用程式 D V D 光碟的檔案內 容,找到 BIN 目錄中的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程 式來開啟選單畫面。 3. 選擇 AMD Software 後,開始進行安裝。 4.
6.4 安 裝 Intel® I350-AM2 Gigabit 介面驅動程式 本節介紹如何安裝 Intel® I350-AM2 Gigabit 驅動程式至系統中。 您需要在 Windows® 作業系統環境中,手動安裝網路驅動程式。 請依照以下的步驟在 Windows® 作業系統中,安裝 Intel® I350-AM2 Gigabit 驅動程 式: 1. 重新開機,並使用 Administrator(主管理者)登入作業系統。 2. 將驅動及公用程式 DVD 光碟放入光碟機中。 若您已經啟動光碟自動偵測的功能,透過作業系統自動偵測的功能,會自行啟動 光碟顯示 Drivers (驅動程式)選單畫面。 若視窗並未自動出現,那麼請瀏覽驅動及公用程式 D V D 光碟的檔案內 容,找到 BIN 目錄中的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程 式來開啟選單畫面。 6-6 3. 點選 Intel® I350-AM2 Gigabit Adapter Driver 項目開始安裝。 4.
5. 點選 Install 進行安裝。 6.
6.5 安裝顯示驅動程式 這裡將介紹如何安裝 ASPEED® 圖形顯示介面(VGA)驅動程式。 您需要在 Windows® Server 系統中,手動安裝 ASPEED 圖形顯示介面驅動程式。 請依照以下步驟,在 Windows® 作業系統中安裝 ASPEED 圖形顯示介面驅動程式: 1. 重新開機,並使用 Administrator(主管理者)登入作業系統。 2. 將驅動及公用程式 DVD 光碟放入光碟機中。 若您已經啟動光碟自動偵測的功能,透過作業系統自動偵測的功能,會自行啟動 光碟顯示 Drivers (驅動程式)選單畫面。 若視窗並未自動出現,那麼請瀏覽驅動及公用程式 D V D 光碟的檔案內 容,找到 BIN 目錄中的 ASSETUP.EXE 程式,並點選 ASSETUP.EXE 主程 式來開啟選單畫面。 6-8 3. 點選在 Drivers(驅動程式)選單裡的 ASPEED AST2500 Display Driver 開始進 行。 4.
5. 點選 Install 進行安裝。 6.
6-10 第六章:安裝驅動程式
附錄 本附錄為提供您參考的相關聯絡資訊。
KNPA-U16 架構圖
Q-Code 列表 Code 00 02 03 04 06 10 11 – 14 15 – 18 19 – 1C 2B – 2F 30 31 32 – 36 37 – 3A 3B – 3E 4F 50 – 53 54 55 56 57 58 59 5A 5B 5C – 5F E0 E1 E2 E3 E4 – E7 E8 E9 EA EB EC – EF F0 F1 F2 F3 F4 F5 – F7 F8 F9 說明 未使用 microcode CACHE_ENABLED PCH 初始化 CPU_EARLY_INIT PEI Core 已開始 Pre-memory CPU 初始化已開始 Pre-memory System Agent 初始化已開始 Pre-memory PCH 初始化已開始 記憶體初始化 預留給 ASL (參考以下 ASL 狀態碼部分的說明) 記憶體已安裝 CPU Post-Memory 初始化 Post-Memory System Agent 初始化已開始 Post-Memory PCH 初始化已開始 DXE IPL 已開始 記憶體初始化錯誤。無效的記憶體類型或不相容記憶體速度 未知的記憶體
Q-Code 列表(續上頁表格) Code FA FB – FF 60 61 62 63 – 67 68 69 6A 6B – 6F 70 71 72 73 – 77 78 79 7A – 7F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E – 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB 說明 無效的 recovery capsule 預留給將來 AMI 錯誤代碼 DXE Core 已開始 NVRAM 初始化 安裝 PCH Runtime 服務 CPU DXE 初始化已開始 PCI 主橋接器初始化 System Agent DXE 初始化已開始 System Agent DXE SMM 初始化已開始 System Agent DXE 初始化 (限定 System Agent 模組) PCH DXE 初始化已開始 PCH DXE SMM 初始化已開始 PCH 裝置初始化 PCH DXE 初始化 (限定 PCH 模組) ACPI 模組初始化 CSM 初始化 預留給將來 AMI DXE 代碼 Boot Device Selection
Q-Code 列表(續上頁表格) Code AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8– BF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC 說明 預留給 ASL (參考以下 ASL 狀態代碼的說明) 可開機項目 延遲開機項目 退出 Boot Services 項目 Runtime Set Virtual Address MAP 開始 Runtime Set Virtual Address MAP 結束 Legacy Option ROM 初始化 系統重置 USB 熱抽換 PCI 熱抽換匯流排 清除 NVRAM 配置重置 (NVRAM 重置) 預留給將來 AMI 代碼 CPU 初始化錯誤 System Agent 初始化錯誤 PCH 初始化錯誤 某些架構協定不可用 PCI 資源分配錯誤。沒有資源 儲存 Legacy Option ROM 空間不足 未發現 Console 輸出裝置 未發現 Console 輸入裝置 無效的密碼 載入開機項目時發生錯誤 (LoadImage 返回錯誤) 開機項目失敗 (StartImage 返回錯誤) Flash
華碩的聯絡資訊 華碩電腦公司 ASUSTeK COMPUTER INC.(台灣) 市場訊息 地址 :台灣臺北市北投區立德路 150 號 4 樓 電話 :+886-2-2894-3447 傳真 :+886-2-2890-7798 網址 :http://www.asus.com/tw/ 技術支援 電話 線上支援 :+886-2-2894-3447(0800-093-456) : h ttps://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=zh-tw ASUS COMPUTER INTERNATIONAL(美國) 市場訊息 地址 :48720 Kato Rd., Fremont, CA 94538, USA 傳真 :+1-510-608-4555 網址 :http://www.asus.com/us/ 技術支援 電話 :+1-812-282-2787 傳真 :+1-812-284-0883 線上支援 : h ttps://www.asus.
華碩電腦(上海)有限公司 ASUSTEK COMPUTER(SHANGHAI)CO., LTD. 市場訊息 地址 : 上海市閔行區金都路 5077 號 電話 :+86-21-5442-1616 傳真 :+86-21-5442-0099 網址 :http://www.asus.com.cn 技術支援 電話 線上支援 :+86-20-2804-7506(400-620-6655) : h ttps://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=zh-cn ASUS Czech Service s.r.o.(歐洲) 市場訊息 地址 :Na Rovince 887, 720 00 Ostrava – Hrabová, Czech Republic 傳真 :+420-596766888 網址 :http://www.asus.
ASUS Holland BV(荷蘭) 市場訊息 地址 網址 :Marconistraat 2, 7825GD EMMEN, The Netherlands :http://www.asus.com/nl/ 技術支援 電話 :+31-(0)591-5-70292 傳真 :+31-(0)591-666853 電子信箱 :advance.rma.eu@asus.com 線上支援 : h ttps://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=nl-nl ASUS Polska Sp. z o.o.(波蘭) 市場訊息 地址 網址 技術支援 電話 線上支援 :Ul. Postępu 6, 02-676 Warszawa, Poland :http://www.asus.com/pl/ :+48-225718033 : https://www.asus.