RS520-E9 系列 服務器 用戶手冊
C16289 8.00 版 2020 年 2 月發行 版權說明 © ASUSTeK Computer Inc. All rights reserved.
目錄 使用注意事項............................................................................................................................... vii 用電安全....................................................................................................................................... viii 電磁安全............................................................................................................................ viii 靜電元件........................................................................................
目錄 2.7 SATA/SAS 背板排線的連接....................................................................................2-26 2.8 系統組件...........................................................................................................................2-28 2.8.1 系統風扇...........................................................................................................2-28 2.8.2 薄型光驅(選配,只 RS520-E9-RS8 支持)....................................2-29 2.8.3 備援式電源(PSU)模塊...................................................
目錄 5.5.10 CSM 設置......................................................................................................5-21 5.5.11 NVMe 設置...................................................................................................5-22 5.5.12 局域網堆棧設置(Network Stack Configuration)......................5-22 5.5.13 iSCSI 設置......................................................................................................5-23 5.6 平台設置菜單(Platform Configuration menu).......................................
目錄 6.3.4 Preferences(偏好設置)..........................................................................6-18 第七章:安裝驅動程序 7.1 安裝 RAID 驅動程序...................................................................................................... 7-2 7.1.1 創建搭載 RAID 驅動程序的 U 盤.............................................................. 7-2 7.1.2 安裝 RAID 驅動程序...................................................................................... 7-2 7.2 安裝應用程序與工具程序........................................................
使用注意事項 操作服務器之前請務必詳閱以下注意事項,避免因人為的疏失造成系統損傷甚至人 體本身的安全。 請勿使用非本產品配備的電源線,由於電路設計之不同,將有可能造成 內部零件的損壞。 ‧ 使用前,請檢查每一條連接線是否都已經依照用戶手冊指示連接妥當,以及電源 線是否有任何破損,或是連接不正確的情形發生。如有任何破損情形,請儘速與 您的授權經銷商聯絡,更換良好的線路。 ‧ 服務器安放的位置請遠離灰塵過多,溫度過高,太陽直射的地方。 ‧ 保持機器在乾燥的環境下使用,雨水、溼氣、液體等含有礦物質將會腐蝕電子線 路。 ‧ 使用服務器時,務必保持周遭散熱空間,以利散熱。 ‧ 使用前,請檢查各項外圍設備是否都已經連接妥當再啟動。 ‧ 避免邊吃東西邊使用服務器,以免污染機件造成故障。 ‧ 請避免讓紙張碎片、螺絲及線頭等小東西靠近服務器之連接器、插槽、孔位等 處,避免短路及接觸不良等情況發生。 ‧ 請勿將任何物品塞入服務器機件內,以避免引起機件短路,或是電路損毀。 ‧ 服務器啟動一段時間之後,散熱片及部份IC表面可能會發熱、發燙,請勿用手觸 摸,並請檢查系統是否散熱不良。 ‧ 在安裝或是移除外圍設備時請先關閉電源。 ‧ 在
用電安全 電磁安全 ‧ 拆裝任何元件或是搬移服務器之前,請先確定與其連接的所有電源都已經拔掉。 ‧ 拆裝任何元件上連接的數據線之前,請先拔掉連接的電源線,或是先安裝數據線 之後再安裝電源線。 ‧ 使用一隻手拆裝數據線,以避免接觸到兩個不同電位表面造成不當的電流突波衝 擊生成。 ‧ 服務器電源線請勿與其他事物機器共用同一個插座,儘量不要使用延長線,最好 能夠連接一台不斷電系統 UPS。 靜電元件 處理器、內存、主板、擴展卡、磁盤、硬盤等設備,是由許多精密的集成電路與其 它元件所構成,這些集成電路很容易因為遭受靜電的影響而損壞。因此,在拆裝任何 元件之前,請先做好以下的準備: ‧ 如果您有靜電環等防靜電設備,請先戴上。 ‧ 假如您所處的環境並沒有防靜電地板,開始拆裝服務器之前,請您先將身體可能 帶的靜電消除。 ‧ 在尚未準備安裝前,請勿將元件由防靜電袋中取出。 ‧ 將元件由防靜電袋中取出時,請先將它與服務器金屬平面部份碰觸,釋放靜電。 ‧ 拿持元件時儘可能不觸碰電路板,及有金屬接線的部份。 ‧ 請勿用手指接觸服務器之連接器、IC 腳位、附加卡之金手指等地方。 ‧ 欲暫時置放元件時請放置在防靜電墊或是防靜電袋上,
關於本用戶手冊 本用戶手冊主要是針對有經驗且具有個人電腦硬件組裝知識的用戶所撰寫的。本手 冊可以幫助您創建起最新、功能強大的華碩服務器。手冊內容介紹本產品各部份元件 的拆裝、設置,因此,部份元件可能是選配配備,並未包含在您的產品當中,假如您 有需要選配該配備,請向本公司授權經銷商洽詢。 章節說明 本用戶手冊的內容結構如下: 第一章:系統導覽 本章以清楚的圖標帶您認識華碩 RS520-E9 系列服務器的功能及特色,包括系統 的前、後面板以及內部功能的介紹。 第二章:硬件安裝 本章以逐步說明的方式,教您如何將系統所需的零組件正確地安裝至本服務器裡 頭。 第三章:高級安裝 本章提供您本服務器的機架安裝及使用方法。 第四章:主板信息 本章提供您有關本服務器內置主板的相關信息,包括主板的結構圖、Jumper 設置 以及連接端口位置等。 第五章:BIOS 程序設置 本章提供您本服務器之 BIOS 的升級與管理及 BIOS 設置的相關信息。 第六章:磁盤陣列設置 在本章節中我們將介紹有關磁盤陣列的設置與說明。 第七章:安裝驅動程序 本章節將提供您相關驅動程序的安裝與說明。 華碩 RS520-E9 系列用戶手冊 ix
提示符號 以下為本手冊所使用到的各式符號說明: 警告:提醒您在進行某一項工作時要注意您本身的安全。 小心:提醒您在進行某一項工作時要注意勿傷害到主板元件。不當的動 作可能會對產品造成損害。 注意:重點提示,重要的注意事項。您必須遵照用戶手冊所描述之方式 完成一項或多項軟硬件的安裝或設置。 說明:小祕訣,名詞解釋,或是進一步的信息說明。提供有助於完成某 項工作的訣竅和其他額外的信息。 哪裡可以找到更多的產品信息 您可以通過下面所提供的兩個渠道來獲得您所使用的華碩產品信息以及軟硬件的升 級信息等。 1. 華碩網站 您可以到 http://www.asus.com.cn 華碩電腦互聯網,來取得所有關於華碩軟硬件 產品的各項信息。 2. 其他文件 在您的產品包裝盒中除了本手冊所列舉的標準配件之外,也有可能會夾帶有其他的 文件,譬如經銷商所附的產品保修單據等。 3. ASUS Control Center(ACC)用戶手冊 本用戶手冊介紹如何設置並使用華碩伺服器管理工具,請至 asuscontrolcenter. asus.
電子電器產品有害物質限制使用標示要求:圖中之數字為產品之環保 使用期限。僅指電子電器產品中含有的有害物質不致發生外洩或突變 從而對環境造成污染或對人身、財產造成嚴重損害的期限。 30 產品中有害物質的名稱及含量: 部件名稱 有害物質 六價鉻 鎘 (Cd) (Cr(VI)) 鉛 (Pb) 汞 (Hg) x o o 印刷電路板及其 電子組件 外部信號連接頭 及線材 外殼 軟驅 電池 光驅 散熱設備 電源適配器 硬盤 中央處理器與內 存 多溴聯苯 (PBB) 多溴二苯醚 (PBDE) o o o x o o o o o o x x x x x x o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o x o o o o o 本表格依據 SJ/T 11364 的規定編制。 ○: 表示該有害物質在該部件所有均質材料中的含量均在 GB/T 26572 規定的限量 要求以下。 ×: 表示該有害物質至少在該部件的某一均質材料中的含量超出 GB/T 26572 規定 的限量要求
xii
第一章: 系統導覽 本章將介紹本服務器的各項組成元件,其中包括系統的 前、後面板以及內部功能的總體介紹。 1
1.1 產品包裝內容 以下為本服務器包裝內的組件。 標準元件 機種型號 RS520-E9-RS12-E 機箱 華碩 2U 機架式機箱 主板 華碩 Z11PR-D16 服務器主板 硬件元件 2 x 800W 備援式電源(PSU) RS520-E9-RS8 2 x 800W 備援式電源(PSU) 12 x 可 熱插拔 3.5 英寸存儲設備 空間 8 x 可熱插拔 3.5 英寸存儲設備空 間 2 x 可熱插拔 2.5 英寸存儲設備空 間 2 x 可熱插拔 2.
1.
1.3 產品規格表 華碩 RS520-E9 系列是一款精心打造的 2U 服務器,內裝 Z11PR-D16 服務器主 板,支持 Intel® Xeon® Scalable 家族處理器,並包含最新內置於主板上的芯片組所提 供的相關技術。 機種型號 RS520-E9-RS12-E RS520-E9-RS8 中央處理器 / 系統總線 2 x Socket P0(LGA 3647) 第一代 Intel® Xeon® Scalable 家族處理器 第二代 Intel® Xeon® Scalable 家族處理器 UPI 10.4 GT/s 核心邏輯 Intel® C621 PCH 芯片組 總插槽數 16(每個 CPU 6 通道;每個 CPU 8 個內存條) 擴展容量 最高可擴展達 4096GB 內存類型 DR4 2933*(每個通道 1 個內存條) D DDR4 2666 / 2400 / 2133 RDIMM/LRDIMM/ LRDIMM 3DS * 內存 當使用 2DPC 設置時 2933MHz 會降為 2666MHz ** 請參考華碩官方網站 w w w.a s u s.
機種型號 硬盤插槽 RS520-E9-RS12-E I = 內置 A 或 S = 可熱 插拔 RS520-E9-RS8 12 x 可 熱抽換 2.5 或 3.5 英寸存儲設備插槽 (支持 4 x NVMe) 2 x 後側面板上可熱抽 換 2.5 英寸存儲設備 插槽(僅支持 SATA SSD) 2 x M.2 2280 / 2260 / 2242(支持 SATA/ PCIE M.2、SATA/ PCIE RAID) * SATA/SAS 需使用選購 的華碩 PIKE II 卡 8x可 熱抽換 2.5 或 3.5 英寸存儲設備插槽 (支持 4 x NVMe) 2x後 側面板上可熱抽 換 2.5 英寸存儲設備 插槽(僅支持 SATA SSD) 2xM .2 2280 / 2260 / 2242(支持 SATA/ PCIE M.
機種型號 RS520-E9-RS12-E 支持操作系統 Regulatory Compliance BSMI、CE、CB、FCC 尺寸(高 x 寬 x 長) 615mm x 444mm x 88mm(2U) 24.21” x 17.48” x 3.46” 毛重(不包含處理器、內存與存儲 設備) 淨重(不包含處理器、內存、存儲 設備;包含外包裝) 24.55 公斤 19.7 公斤 30.1 公斤 27.97 公斤 電源(PSU) 1+1 備援式 800W 80PLUS Platinum 電源模塊 電氣額定值 100-127Vac/200-240Vac, 9.4A/4.72A, 47-63 Hz, Class I(for each inlet) 環境條件 操作溫度:10℃ ~ 35℃ 未操作溫度:-40℃ ~ 60℃ 未操作濕度:20% ~ 90%(無結露) * 列表規格若有更改,恕不另行通知。 1-6 RS520-E9-RS8 請參考華碩官方網站 http://www.asus.com.
1.4 前面板 本服務器的前面板提供了簡單的存取功能,包括電源按鈕、重置按鈕、相關的 LED 指示燈、Location 按鈕、薄型光驅(選配,RS520-E9-RS8 支持)及兩個 USB 接 口,可方便您隨時瞭解系統的狀況。 關於前面板 LED 指示燈的介紹,請參考 1.7.1 前面板指示燈 的說明。 當要移除或更換系統內的元件時,請將系統電源關閉。 RS520-E9-RS8 重置(RESET)按鈕 Location 按鈕 2 個 USB 3.0 接口 電源按鈕 薄型光驅(選配) 顯示器接口 請見 1.7 LED 顯示燈號說明 4 插槽 1 插槽 3 插槽 2 插槽 5 插槽 4 3 2 1 插槽 7 插槽 6 插槽 8 ‧ 插槽 1 至 4 支持 Hybrid NVMe / SAS / SATA(SAS 需使用選購的 華碩 PIKE II 卡)。 ‧ 插槽 5 至 8 支持 SAS / SATA(SAS 需使用選購的華碩 PIKE II 卡)。 RS520-E9-RS12-E 請見 1.7 LED 顯示燈號說明 插槽 10 插槽 4 USB 2.
1.5 後面板 後面板包含了所有連接設備的接口、後置風扇等。下圖即為服務器後面板圖標。 2.5 英寸插槽 2 網絡接口 2 顯示器接口 2.5 英寸插槽 1 電源模塊與電源線連接孔 DM 管理網絡接口* Q-Code 指示燈 電源按鈕 2 個 USB 3.
Asset tag(財產標籤) Asset tag(財產標籤)是一個既簡單又相當好用的設備,設計位於服務器前面板 以提供您方便抽出使用。在此設備上面可以讓您寫下關於服務器上的重要信息。 RS520-E9-RS8 RS520-E9-RS12-E 華碩 RS520-E9 系列用戶手冊 1-9
1.6 內部組件 下圖即為本服務器的標準內部組件: RS520-E9-RS8 1. 備援式電源(PSU) 2. 華碩 Z11PR-D16 服務器主板 3. SATA/SAS/NVMe 背板 4. 薄型光驅(選配) 5. 系統風扇 6. Asset tag(財產標籤)(隱藏) 7. 8 x 3.5 英寸存儲設備插槽 8. PCIE-NVME4-OCuLink 卡 9. 2 x 2.
RS520-E9-RS12-E 1. 備援式電源(PSU) 2. 華碩 Z11PR-D16 伺服器主板 3. SATA/SAS/NVMe 背板 4. 前側 USB 面板 5. 系統風扇 6. Asset tag(財產標籤)(隱藏) 7. 12 x 3.5 英寸存儲設備插槽 8. PCIE-NVME4-OCuLink 卡 9. 2 x 2.5 英寸存儲設備插槽 10.
1.7 LED 顯示燈號說明 1.7.
1.7.2 存儲設備指示燈 前側面板 存儲設備狀態指示燈(紅燈) 存儲設備動作指示燈(綠燈) 指示燈 存儲設備動作指示 燈 存儲設備狀態指示 燈 燈號 顯示 熄滅 亮綠燈 綠燈閃爍 說明 找不到存儲設備 無動作 1.讀取 / 寫入數據至存儲設備中 亮紅燈 2.指示位置 存儲設備失效並且應立即更換 1.RAID 重建正在進行 紅燈閃爍 2.RAID Locating 3.存儲設備熱備援 後端面板 存儲設備動作指示燈(綠燈) 指示燈 存儲設備動作指示 燈 燈號 顯示 熄滅 亮綠燈 綠燈閃爍 說明 找不到存儲設備 無動作 1.讀取 / 寫入數據至存儲設備中 2.
1.7.3 網絡接口指示燈 SPEED LED ACT/LINK LED SPEED LED ACT/LINK LED ACT/LINK LED 指示燈 SPEED LED 指示燈 燈號狀態 說明 燈號狀態 說明 熄滅 未連接 熄滅 10 Mbps 連接 綠燈 已連接 橘燈 100 Mbps 連接 閃爍 正在存取數據 綠燈 1 Gbps 連接 1.7.
1.7.
Action PHASE PEI(Pre-EFI initialization) phase Normal boot POST CODE TYPE 51 52 58 5A 5B 5C 5D 5F 60 61 68 69 70 71 7D 7E 7F 55 32 MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress MRC Progress Progress MRC_RH_PREVENTION MRC_GET_MRC_DATA MRC_RETRAIN_CHECK MRC_SA_GV_SWITCH MRC_ALIAS_CHECK MRC_ECC_CLEAN_START MRC_DONE MRC_CPGC_MEMORY
第二章: 硬件安裝 本章節要告訴您如何安裝及卸除本服務器各個部分的組 件,以及在安裝過程中必需注意的事項。 2
2.1 機箱上蓋 2.1.1 打開機箱後半部上蓋 1. 將機箱上蓋固定在機箱後面板的二顆螺絲釘鬆開。注意:螺絲釘只需鬆開,不需 要完全取下。 免卸螺絲 2. 將機箱後半上蓋向後推,並使後半部上蓋前緣與前半部上蓋保留約半英寸距離。 3.
2.2 中央處理器(CPU) 本主板具備 LGA 3647 處理器插槽,本插槽是專為 LGA 封裝的 Intel ® Xeon ® Scalable 家族處理器所設計。 在安裝處理器之前,請確認所有電源線已經移除。 ‧ 在您購買主板後,請確認兩個 LGA 插座上皆附有一個即插即用的保 護蓋,並且插座接點沒有彎曲變形。若是保護蓋已經毀損或是沒有保 護蓋,或者是插座接點已經彎曲,請立即與您的經銷商聯絡。 ‧ 在安裝完主板之後,請將即插即用的保護蓋保留下來。只有在處 理器插槽上附有即插即用保護蓋的主板符合 Return Merchandise Authorization(RMA)的要求。華碩電腦才能為您處理產品的維修 與保修。 ‧ 本保修不包括處理器插座遺失、錯誤的安裝或不正確的移除即插即用 保護蓋所造成的毀損。 2.2.1 安裝中央處理器 請依照以下步驟安裝處理器: 1. 依照前面步驟移除後端上蓋板。 2.
3. 將 CPU 上的三角形標誌對齊 CPU 安 裝盒右上角處的三角形標誌(A),小 心地將 CPU 放入(B),接著將 CPU 安裝盒安裝至散熱器中(C)。 CPU 安裝盒 請確認 CPU 上的三角形標誌與 CPU 安裝盒右上角處的三角形 標誌方向相符。 三角標誌 2 CPU 4. 將 CPU 及 CPU 安裝盒對齊,將散熱器放置在已安裝好的 CPU 上方。 CPU 及 CPU 安裝盒只能以單一方向正確地安裝到主板上的插槽。切記請 勿用力地將 CPU 及 CPU 安裝盒以錯誤的方向安裝到插槽上,這麼做將可 能導致 CPU 與插槽上的接腳損壞。 5.
6. 裝回導風罩,如下圖所示。 2.3 系統內存 2.3.
2.3.
2.3.3 安裝內存條 安裝移除內存條前,請確認已安裝中央處理器、散熱器與導風罩。 請依照下面步驟安裝內存條: 內存條缺口 1. 先將內存條插槽的固定卡扣扳開。 2. 將內存條的金手指對齊內存條插槽的 溝槽,並且在方向上要注意金手指的 缺口要對準插槽的凸起點。 插槽凸起點 往外扳開內存條插 槽的卡扣 內存插槽上的凹槽為設計只一個方向供內存條插入,請在裝入前,確定 內存條與內存插槽上的安裝方向是契合的。 3. 最後緩緩將內存條插入插槽中,若無 錯誤,插槽的卡扣會因內存條安裝而 自動扣到內存條的凹孔中。 卡扣會在內存條正確 安裝後自動扣上 請將內存條缺口對準插槽的凸起點並垂直插入,以免造成內存條缺口損 壞。 2.3.4 取出內存條 請依照以下步驟取出內存條: 1. 壓下內存條插槽的固定卡扣以鬆開內存 條。 2.
2.4 安裝存儲設備 RS520-E9-RS8 支持 8 個、 RS520-E9-RS12-E 支持 12 個之可熱抽換 2.5 或 3.5 英寸存儲設備插槽。在後面板並支持可安裝 2 個 2.5 英寸可熱抽換存儲設備。而 存儲設備的安裝方式,是經由裝入連接在主板 SATA/NVMe 背板上的 SATA/NVMe 擴展槽來使用(SAS 需使用選購的華碩 PIKE II 卡)。 • RS520-E9-RS8:背板控制器默認僅支持 SATA 存儲設備,若您想 要安裝 SAS 存儲設備時,請先安裝選配的華碩 PIKE II 卡。 • RS520-E9-RS12-E:若您想要於背板上安裝 SATA 或 SAS 存儲設 備時,請先安裝華碩 PIKE II 卡。 請按照以下的步驟,安裝 3.5 英寸熱插拔存儲設備: 1. 請先將握把上的固定扣朝右方撥開(A),以便將硬盤槽握把鬆開(B)。 握把 固定扣 2. 將握把朝左扳開時,硬盤槽便會向 外滑出,請順勢將硬盤擴展槽往主 機的前方抽離。 3. 將硬盤槽放置在平坦桌面上。 4.
5. 安裝存儲設備,再使用 4 顆螺絲, 將存儲設備鎖緊固定在硬盤槽內。 6. 當存儲設備安裝完畢後,請以手緊握 住硬盤槽握把安裝系統的插槽中,將 其輕推至機箱底部。 當安裝後,硬盤槽上的 SATA/SAS/NVMe 接口會完全與背板上的插座 契合。 7. 最後請將板手輕輕地推回原位並輕扣 固定,使硬盤槽能夠緊密地固定在機 箱中。 如果硬盤槽有正確地安裝, 您將會看到硬盤槽外緣與機 箱呈現切齊的狀態。 8.
請按照以下的步驟,安裝 2.5 英寸熱插拔存儲設備: 1. 請先將握把上的固定扣朝右方撥開(A),以便將硬盤槽握把鬆開(B)。 握把 固定扣 2. 將握把朝左扳開時,硬盤槽便會向 外滑出,請順勢將硬盤擴展槽往主 機的前方抽離。 3. 將硬盤槽放置在平坦桌面上。 4.
5. 安裝存儲設備,再使用 4 顆螺絲, 將存儲設備鎖緊固定在硬盤槽內。 6. 當存儲設備安裝完畢後,請以手緊握 住硬盤槽握把安裝系統的插槽中,將 其輕推至機箱底部。 當安裝後,硬盤槽上的 SATA/SAS/NVMe 接口會完全與背板上的插座 契合。 7. 最後請將板手輕輕地推回原位並輕扣 固定,使硬盤槽能夠緊密地固定在機 箱中。 如果硬盤槽有正確地安裝, 您將會看到硬盤槽外緣與機 箱呈現切齊的狀態。 8.
請按照以下步驟,從後側面板安裝 2.5 英寸熱插拔存儲設備: 1. 請先將握把上的固定扣撥開,以便將存 儲設備槽握把鬆開。 握把 固定扣 2. 將握把朝外扳開時,存儲設備槽便會 向外滑出,請順勢將存儲設備擴充槽 往主機的前方抽離。 3.
4. 如圖示方向,將存儲設備上的螺絲孔對準擴充槽兩側的螺絲孔位置入。 請確認存儲設備上的四個螺絲安裝孔,已經對準擴充槽上的安裝孔位。 存儲設備螺絲孔 存儲設備插槽螺絲孔位 5. 將裝好 2.5 英寸存儲設備的插槽,握住握把對準主機上的安裝位置推回原位,並 扣上固定扣,使插槽能夠緊密地固定在機殼中。 當裝妥時,在存儲設備後方的接口會與背板上的插座緊密接合。 6. 若要安裝其他 2.5 英寸存儲設備,請重複步驟 1-5 進行。 RS520-E9-RS12-CN 可以由 BMC 中點擊 系統 HDD 信息 查看後置 2.
2.5 擴展插槽 在本服務器內的主板上的 PCIE 插槽,可以您提供安裝 Low-Profile 規格之擴展 卡,當您需要擴展的時候,可以進行安裝。 2.5.1 安裝擴展卡至 PCIE 插槽 請依照以下的步驟安裝擴展卡: 1. 找 到 位 於 固 定 檔 板 支 架 上 的 兩 顆 螺 絲,使用螺絲起子移除螺絲。 2.
3. 使用螺絲起子,將固定在機箱金屬檔 板上的螺絲卸除。 然後將金屬檔板取出,並妥善保存以 備未來若要裝回時使用。 4. 將擴展卡插入主板上的 PCIE 插槽, 請確認卡上的金手指部分已經完全沒 入插槽中,然後再鎖上先前卸除的螺 絲。 5.
2.5.2 於 PCI-E 6 安裝華碩 PIKE II 卡 請依照以下的步驟於 PCI-E 6 安裝華碩 PIKE II 卡: 1. 移除主板與背板上的排線。 以上圖示僅供參考。 2. 取出準備安裝的華碩 PIKE II 卡。 若擴展卡已經預先裝妥以下的華碩專用擋板,請直接跳到步驟 5 繼續。 2.
4. 將金屬擋板與華碩 PIKE II 卡固定。 金屬擋板 5. 連接 mini-SAS HD 排線至華碩 PIKE II 卡。 連接至 ASUS PIKE II 插槽 2 連接至 ASUS PIKE II 插槽 1 6. 將華碩 P I K E I I 卡及金屬擋板安裝至至 P C I E 插槽。請確認 A S U S P I K E I I 上的金手指部分已完全沒入插槽內。 安裝擴展卡至 PCIE 插槽的說明,請參考 2.5.
2.5.3 更換華碩 PCIE-NVME4-OCuLink 卡 華碩 PCIE-NVME4-OCuLink 卡已預先安裝於 PCIE 插槽 1,以支援在插槽 1 至插 槽 4 使用 NVME 存儲設備。 請依照以下步驟更換華碩 PCIE-NVME4-OCuLink 卡: 1. 找 到 位 於 固 定 檔 板 支 架 上 的 兩 顆 螺 絲,使用螺絲起子移除螺絲。 2. 取出檔板支架,並放置於一旁。 3.
4. 將 OCuLink 排線由個別插槽上移除。 OCuLink 端口 4 OCuLink 端口 3 OCuLink 端口 2 OCuLink 端口 1 5. 取出準備更換的華碩 PCIE-NVME4-OCuLink 卡。 6.
7. 安裝華碩 PCIE-NVME4-OCuLink 卡至主板上的 PCIE 插槽。請確認金手指部分已 完全沒入插槽內,並鎖上螺絲固定。 8.
2.5.4 設置擴展卡 安裝好擴展卡之後,接著須通過軟件設置來調整擴展卡的相關設置。 1. 啟動電腦,然後更改必要的 BIOS 程序設置。若需要的話,您也可以參閱第五章 BIOS 程序設置以獲得更多信息。 2. 為加入的擴展卡指派一組尚未被系統使用到的 IRQ。請參閱下表中所列出的中斷 請求(IRQ)使用一覽表。 3.
2.5.5 安裝 M.2 擴展卡 您可以在主板上提供的 M.2 插槽上面安裝一張 M.2 擴展卡。 請依照以下的步驟安裝 M.2 擴展卡: 1. 使用螺絲起子將固定 M.2 插槽的螺絲移除,並放置於一旁。 2. 取出 M.2 擴展卡。 3. 如下圖所示,將 M.2 擴展卡對準主板上的 M.2 插槽裝入。 4. 鎖上步驟 1 移除的螺絲以固定 M.2 擴展卡,完成安裝。 • 移除螺絲時請留意螺絲座可能被一起移除。 • 固定 M.2 擴展卡前請確認 M.
2.5.6 安裝 Mezzanine(夾層)卡 本系統提供一個 Mezzanine(夾層)卡插槽以提供您安裝此卡。 請依照以下步驟安裝 Mezzanine(夾層)卡: 1. 使用螺絲起子將 Mezannine(夾層) 卡擴展槽的金屬擋板移除。 2. 取出 Mezannine(夾層)卡與信號線,將信號線的信號發送端(白色)接口連接 到卡上的 AUXLED_CON1 插座。 AUXLED_CON1 3.
4. 鎖上 4 顆螺絲以固定 Mezzanine(夾層)卡。 5.
2.6 連接排線 ‧ 系統內的排線在出廠前都已經預先連接妥當。您不需再另外安裝,除 非您需要更換或安裝增加的硬件,才需要重新連接/移除。 ‧ 請參考第 4 章以了解更多關於排線與插座連接的相關信息。 預先連接的系統排線 1. 24-pin ATX 電源接口(電源(PSU)至主板) 2. 8-pin 12V 電源接口(電源(PSU)至主板) 3. 系統風扇連接插座(主板至系統風扇) 4. USB 連接插座(主板至前側 I/O 面板) 5. SATA 插座(主板至後側背板) 6. 系統輔助面板連接插座(主板至前側 I/O 面板) 7. 系統面板連接插座(主板至前側 I/O 面板) 8. SATA 接座 (主板至前側背板) 9.
2.
RS520-E9-RS12-E 連接電源(PSU) 的 8-pin 電源 用排線連接至選配的 ASUS PIKE II 卡 OCUPCIE4 PWR1 預留擴充插座 MSAS_HD1 OCUPCIE1 MSAS_HD2 OCUPCIE2 MSAS_HD3 OCUPCIE3 連接連接至 ASUS PCIE-NVME4-OCuLink 卡的排線 華碩 RS520-E9 系列用戶手冊 2-27
2.8 系統組件 當您在安裝或移除系統設備或是替換損壞的零組件時,或許需要移除先前所安裝的 系統組件。而本章節的內容就是要告訴大家如何移除與重新安裝下列的系統組件。 1. 系統風扇 2. 薄型光驅(選配) 3. 備援式電源(PSU)模塊(選配) 安裝/移除系統組件之前,請先關閉系統電源。 2.8.1 系統風扇 請依照以下的步驟,移除系統風扇: 1. 直接用手壓住風扇的左右兩側握柄,然後向上取出風扇。 2. 重覆步驟 1,即可移除其他系統風扇。 依照以下的步驟,安裝系統風扇: 1.
2.8.2 薄型光驅(選配,只 RS520-E9-RS8 支持) 請依照以下的步驟,安裝選配的薄型光驅: 1. 移除上方兩個固定薄型光驅擴展槽蓋 板的螺絲。 2. 取出薄型光驅並於兩側邊各分別鎖上 兩顆螺絲,將薄型光驅鎖入擴展架。 3. 將薄型光驅,裝入機箱上的光驅擴展 槽。 4.
請依照以下的步驟,移除薄型光驅: 1. 找到位於薄型光驅擴展槽後方的固定 閂(如右圖圈選處)。 2.
2.8.3 備援式電源(PSU)模塊 請依照以下的步驟,更換備援式電源(PSU)模塊: ‧ 在移除任何元件之前,請先將系統關機。 ‧ 通過觸摸任何金屬表面以將靜電釋放。 ‧ 使用相同型號與類型的備援式電源(PSU)模塊。 安裝第二組備援式電源(PSU)模塊 請依照以下的步驟,安裝第二組備援式電源(PSU)模塊: 1. 朝左壓固定閂(A)。 2. 然後將金屬保護蓋板(B)從機箱上 面抽離。 3. 準備第二個備援式電源(PSU)模塊。 請確認在安裝模塊前,先卸下塑料保護蓋。 4. 小心地將第二組備援式電源(P S U) 模塊,安裝機箱的托架內。 5.
2-32 第二章:硬件安裝
第三章: 高級安裝 本章節要告訴您,如何使用滑軌套件將本服務器安裝至 機架中,以及在安裝過程中必須注意的事項。 3
3.1 免工具標準式滑軌套件 免工具的滑軌套件設計,提供您輕鬆將滑軌裝上機架並安裝服務器至機架中,而無 須使用任何工具。這個套件並提供金屬止擋,可以讓您在安裝服務器時提供額外的支 撐和穩定性。 免工具滑軌套件包含了以下組件: 螺絲組 固定閂 滑軌鐵件(含螺絲) 固定閂螺絲 滑軌墊圈 滑軌螺絲 免工具機架滑軌 安裝免工具機架滑軌 請依照以下步驟,將免工具機架滑軌安裝至機架上: 1.
2. 選擇所需的空間和適當的機架滑軌(左和右)放在機架的相對位置上。 在這 1U 的空間裡面要有三個方形安裝孔與在上方與底部包含二個薄型 的間隔,如下圖圈選處。 1U 3. 使用包裝內附的螺絲將滑軌鐵件安裝至滑軌上。 4. 上推彈簧鎖( ),然後將螺栓插入已選定在機架上的方形安裝孔。 5. 上推滑軌另一端的彈簧鎖,然後插入已選定在機架上的方形安裝孔。如有必要, 請將機架滑軌拉長以便於安裝。 6. (可選擇)可使用附件裡的滑軌螺絲以及滑軌墊圈( 上兩顆套上此墊圈的螺絲以進行固定。 ),將滑軌前後端各鎖 滑軌螺絲的扭矩值建議為 14 kgf.cm。 7. 接著請重複前面的步驟 3 至 5,安裝另一側的滑軌。 請確認安裝的機架滑軌(左、右)有平行一致,且安穩地固定在定位。 8.
‧ 請確認機架滑軌機櫃與機架裝配的位置是穩定的,且牢靠地站立在同 一水平高度上。 ‧ 強烈推薦至少需要兩位身強體壯的人來運行這部份的安裝操作。 ‧ 如有必要,推薦使用適當的起重工具以輔助吊裝。 RS520-E9-RS8 前視圖 4 3 2 1 RS520-E9-RS12-E 前視圖 請確認服務器兩側的結點(knots)裝入機架滑軌的安裝孔裡。。 圖示僅供參考。 3-4 第三章:高級安裝
3.2 滑軌尺寸 43.6mm 900mm 43.
3-6 第三章:高級安裝
第四章: 主板信息 在本章中要告訴您在安裝系統元件時所必須完成的主板 安裝程序。詳細內容有:頻率開關設置、跳線選擇區設置 以及主板的各種設備接口。 4
4.
主板的各項元件 內部連接插槽 / 開關與跳線選擇區 / 指示燈 頁碼 1. CPU, front, and rear fan connectors (4-pin FRNT_FAN1-7; REAR_FAN1-2) 4-15 2. TPM connector (14-1 pin TPM1) 4-16 3. Auxiliary panel connector (20-2 pin AUX_PANEL1, 20-pin AUX_ PANEL2) 4-19 4. Chassis Intrusion (2-pin INTRUSION1-2) 4-21 5. USB 2.0 connector (10-1 pin USB78; USB56) 4-14 6. Power Supply SMBus connector (5-pin PSUSMB1) 4-24 7. ATX power connectors (24-pin EATXPWR; 8-pin EATX12V1; 8-pin EATX12V2) 4-17 8.
4.2 跳線選擇區 1.
2. VGA 控制器設置(3-pin VGA_SW1) 您可以通過本功能的設置來開啟或關閉主板內置之 V G A 圖形顯示控制器功 能。默認值為 [1-2](開啟 VGA 功能)。 3.
4. ME 固件強制恢復設置(3-pin ME_RCVR1) 這組跳線帽提供您當 Intel Management Engine(ME,管理引擎)固件發生損 壞時,可以快速恢復。 5.
6. DDR4 thermal event 設置 (3-pin DIMMTRIP1; DIMMTRIP2) 本跳線帽提供您啟用(默認)或關閉 DDR4 溫度感應事件針腳。 7.
8. Smart Ride Through(SmaRT)設置(3-pin SMART_PSU1) 本跳線帽提供您啟用或關閉 Smart Ride Through(SmaRT)功能。本功能預 設為啟用。設置為 [2-3] 以關閉本功能。當本功能開啟時,SmaRT 允許電源不足 時系統不間斷運行。 9.
10. DMLAN 設置(3-pin DM_IP_SEL1) 本跳線帽提供您選擇 DMLAN 設置。設置為 [2-3] 以強制 DMLAN IP 使用固 定模式(IP=10.10.10.10, submask=255.255.255.
4.3 內部指示燈 1. 電力指示燈(SBPWR1) 當主板上內置的電力指示燈(SB_PWR1)亮著時,表示當前系統是處於正常 運行、省電模式或者軟關機的狀態中,並非完全斷電。這個警示燈可用來提醒您 在安裝或移除任何的硬件設備之前,都必須先移除電源,等待警示燈熄滅才可進 行。請參考下圖所示。 2.
3.
5. BMC 警示燈(BMCLED1) 當綠色警示燈以每秒閃爍時,表示 ASMB8 正常工作。 6.
4.4 元件與外圍設備的連接 1. Serial ATA 6.0/3.0 Gbps 接口(7-pin SSATA1-3) 這些接口由 Intel® 621 系列芯片所控制,可以支持使用細薄的 Serial ATA 信 號線連接 Serial ATA 硬盤(SATA1 接口默認為連接光驅)。 2.
3. USB 2.0(10-1 pin USB78; USB56) 這些插槽可用來連接 USB 2.0 接口。將 USB 擴展套件連排線連接到 USB34, 然後將擴展套件安裝到機箱背部的一個空置插槽位置。這些 USB 擴展套件排線 插槽支持 USB 2.0 規格,傳輸速率高達 480 Mbps。 USB 模塊為選購配備,請另行選購。 4. USB 3.0 連接插槽(20-1 pin USB3_34) 這個插槽用來連接 USB 3.0 模塊,可在前面板或後側接口擴展 USB 3.0 模 塊。當您安裝 USB 3.0 模塊,您可以享受 USB 3.0 的益處,包括有更快的數據 傳輸率最高達 5Gbps、對可充電的 USB 設備更快的充電速度、最佳化能源效 率,以及與 USB 2.
5. CPU、前端與後端風扇電源插座 (4-pin FRNT_FAN1-7; REAR_FAN1-2) 這些插座為支持連接冷卻風扇使用。將風扇電源線連接到主板上的風扇插座, 請確認黑線需接到風扇電源插座上的接地端(GND)。連接風扇電源插座時,一 定要注意到極性問題。 千萬要記得連接風扇的電源,若系統中缺乏足夠的風量來散熱,那麼很 容易因為主機內部溫度逐漸昇高而導致死機,甚至更嚴重者會燒毀主板 上的電子元件。 6.
7. 串行連接插座 (10-1 pin COM1) 這個插座用來連接串口(COM)。將串口模塊的信號線連接至這個插座,接著 將該模塊安裝至機箱後面板空的插槽中。 COM 模塊為選購配備,請另行選購。 8.
9. ATX 電源插座 (24-pin EATXPWR1; 8-pin EATX12V1; 8-pin EATX12V2) 這個插座為提供給 A T X 電源使用。由電源所提供的連接插頭已經過特別設 計,只能以一個特定方向插入主板上的電源插座。找到正確的插入方向後,只需 穩穩地將之套進插座中即可。 • 請務必連接 24-pn 與 8-pin 電源插座,否則系統將不會啟動。 • 若您想要安裝其他的硬件設備,請務必使用較高功率的電源(PSU) 以提供足夠的設備用電需求。若電源(PSU)無法提供設備足夠的用 電需求,則系統將會變得不穩定或無法啟動。 ‧ 本主板支持 ATX2.
10.
11.
12. VGA 連接排針(10-1 pin VGA_HDR1) 這個排針支持 VGA 高動態範圍(High Dynamic-Range)接口。 13.
14. 機箱開啟警示連接排針(2-pin INTRUSION1-2) 這組排針提供給設計有機箱開啟檢測功能的電腦主機機箱之用。此外,尚須搭 配一個外接式檢測設備,譬如機箱開啟檢測感應器或者微型開關。在本功能啟用 時,若您有任何移動機箱元件的動作,感應器會隨即檢測到並且送出一信號到這 組接針,最後會由系統記錄下這次的機箱開啟事件。默認設置為 CASEOPEN 與 GND 接腳短路,此功能關閉。 15.
16. Mezzanine PCI 卡插槽 (MEZZPCIE1-2) MEZZ1 插槽支持 OCP(Open Compute Project)擴展卡。 17. Micro SD 存儲卡插槽(MSD1) 主板支持 SD 存儲卡 v2.00(SDHC) / V4.
18. VROC_KEY 接針(4-pin VROC_KEY) 本接針用來連接 KEY 模塊以啟用支持 Intel® CPU RSTe 功能。 KEY 模塊為選購配備,請另行選購。 19. M.2(NGFF)插槽(NGFF1-2) 本插槽提供安裝一個 M.2 設備。 此插槽支持 2242/2260/2280 類型的 PCI-E 與 SATA 存儲設備。 M.
20. 電源(PSU) SMBus 連接排針(5-pin PSUSMB1) 您可通過本組排針連接到電源(P S U)系統管理總線(S M B u s,S y s t e m Management Bus)接口設備(若您的電源(PSU)有支持本項功能)。 本插座僅開啟 BMC_EN1 時才能使用。 21.
第五章: BIOS 程序設置 B I O S 程序調校的優劣與否,和整個系統的運行性能有 極大的關係。針對自己的配備來作最佳化 BIOS 設置,可 讓您的系統性統再提升。本章節將逐一說明 BIOS 程序中 的每一項配置設置。 5
5.1 管理、更新您的 BIOS 程序 下列軟件讓您可以管理與更新主板上的 BIOS 設置。 1. ASUS CrashFree BIOS 3 當 BIOS 程序毀損時,使用可啟動的 U 盤來更新 BIOS 程序。 2. ASUS EzFlash 使用 U 盤更新 BIOS。 3. BUPDATER 使用可啟動的 U 盤在 DOS 環境下更新 BIOS 程序。 上述軟件請參考相關章節的詳細使用說明。 推薦您先將主板原始的 BIOS 程序備份到可啟動的 U 盤中,以備您往後 需要再次安裝原始的 BIOS 程序。使用華碩在線更新(ASUS Update) 程序來拷貝主板原始的 BIOS 程序。 5.1.
5.1.2 使用華碩 EzFlash 更新程序 華碩 EzFlash 程序讓您能輕鬆的更新 BIOS 程序,可以不必再通過啟動盤的冗長程 序或是到 DOS 模式下運行。 請至華碩網站 http://www.asus.com.cn 下載最新的 BIOS 程序文件。 請依照下列步驟,使用 EzFlash 來更新 BIOS: 1. 將已存好最新版 BIOS 文件的 U 盤插入 USB 接口。 2. 進入 BIOS 設置程序。來到 Tools 菜單,選擇 ASUS EZ Flash Utility 後並按下 鍵將其開啟。 ASUS Tek. EzFlash Utility Current Platform Platform : Z11PR-D16 Version : 0203 Build Date :06/06/2017 FS0 New Platform Platform : Z11PR-D16 Version : 0205 Build Date :07/07/2017 System Volume Information Z11PR-D16-ASUS-0205.
5.1.3 BUPDATER 工具程序 以下的 BIOS 畫面只能參考,請依您所見的實際 BIOS 畫面為準。 BUPDATER 工具程序可以提供您在 DOS 環境下,使用存儲有更新的 BIOS 文件的 U 盤來更新 BIOS 文件。 更新 BIOS 文件 請依照以下的步驟,使用BUPDATER 工具程序來更新 BIOS 文件: 1. 請先訪問華碩網站(www.asus.com.cn)下載最新主板的 BIOS 文件。並將文件 存儲至可啟動的 U 盤內。 2. 然後將華碩支持網站(s u p p o r t.a s u s.c o m)上的 B U P D A T E R 工具程序 (BUPDATER.exe),下載並存儲至同一個可啟動的 U 盤內。 3. 將系統啟動至 DOS 環境下,然後使用鍵盤輸入命令: BUPDATER /i [filename].CAP [ filename] 這裡的意思就是輸入存放在 U 盤裡頭的最新或原本 BIOS 文件名稱,然 後按 鍵。 A:\>BUPDATER /i[file name].
4. 程序會進行檢查文件,然後開始更新 BIOS 文件。 ASUS Tek. EzFlash Utility Current Platform Platform : Z11PR-D16 Version : 0203 Build Date :06/06/2017 New Platform Platform : Z11PR-D16 Version : 0205 Build Date :07/07/2017 Start programming the Flash. DO NOT SHUTDOWN THE SYSTEM!!! Write ... 25% 請勿在更新 BIOS 程序文件時關閉或重新啟動系統,此舉將會導致系統損 毀! 5. 完成更新後,程序會回到 DOS 畫面,請重新啟動系統,通過硬盤啟動。 The BIOS update is finished! Please restart your system. C:\> 華碩 RS520-E9 系列用戶手冊 5-5
5.2 BIOS 程序設置 主板擁有一片可編輯的固件芯片,您可以依照 5.
5.2.1 BIOS 程序菜單介紹 菜單項目 功能表列 設置值 一般說明 操作功能鍵 5.2.
5.2.3 菜單項目 於功能表列選定選項時,被選擇的功能將會反白,假設您選擇 Main 功能,則會顯 示 Main 菜單的項目。 點擊菜單中的其他項目(如:Event Logs、Advanced、Monitor、Boot、Tool 與 Exit 等)也會出現該項目不同的選項。 5.2.4 子菜單 在菜單畫面中,若功能選項的前面有一個小三角形標記,代表此為子菜單,您可以 利用方向鍵來選擇,並且按下 鍵來進入子菜單。 5.2.5 操作功能鍵說明 在菜單畫面的右下方為操作功能鍵說明,請參照功能鍵說明來選擇及改變各項功 能。 5.2.6 一般說明 在菜單畫面的右上方為當前所選擇的作用選項的功能說明,此說明會依選項的不同 而自動更改。 5.2.7 設置值 這些存在於菜單中的設置值是提供給用戶選擇與設置之用。這些項目中,有的功能 選項只為告知用戶當前運行狀態,並無法更改,那麼此類項目就會以淡灰色顯示。而 可更改的項目,當您使用方向鍵移動項目時,被選擇的項目以反白顯示,代表這是可 更改的項目。 5.2.
5.3 主菜單(Main) 當您進入 BIOS 設置程序時,首先出現的第一個畫面即為主菜單,內容如下圖。 5.3.1 System Date [Day xx/xx/xxxx] 設置您的系統日期。 5.3.
5.
5.
5.5.1 Trusted Computing Configuration Security Device Support [Disabled] 可讓您啟動或關閉 BIOS 安全設備支持功能。設置值有:[Disabled] [Enabled] 5.5.
5.5.3 Smart Setting(智能設置) SMART Self Test [Enabled] 提供您在 POST(開機自檢)過程時,在所有硬盤上面運行 SMART Self Test(智 能型自我測試)。設置值有:[Disabled] [Enabled] 5.5.
5.5.
Parity [None] 一個 parity(同位)位能發送數據位來檢測一些傳輸錯誤,[Mark] 與 [Space] parity 則不允許錯誤檢測。 [None] None。 [Even] 同位位為 0,表示 N 個位裡,1 出現的總次數為偶數。 [Odd] 同位位為 0,表示 N 個位裡,1 出現的總次數為奇數。 [Mark] 同位位總是 1。 [Space] 同位位總是 0。 Stop Bits [1] Stop bits 為串行數據封包的終點(開始位表示起始)。標準設置是 1 Stop bit。使用較慢的設備通信可能會需要超過 1 stop bit。設置值有:[1] [2] Flow Control [Hardware RTS/CTS] F l o w c o n t r o l(流量控制)能預防在緩衝區溢滿時的數據流失。當傳送數據 時,若接收的緩衝區已經滿了,此時會送出“stop”(停止)信號來停止傳送數 據流(data flow)。當緩衝區空出時,會再送出“start”(開始)信號以重新開 始傳送數據流。硬件流量控制使用兩條金屬線來傳送 start/stop(開始/停止)
S e r i a l P o r t f o r O u t-o f-B a n d M a n a g e m e n t/W i n d o w s E m e r g e n c y Management Services (EMS) Settings COM2 Console Redirection [Disabled] 啟用或關閉控制面板轉向功能。設置值有: [Disabled] [Enabled] 當 Console Redirection 設置為 [Enabled] 時,以下的項目才會顯示。 Console Redirection Settings Out-of-Band Mgmt Port [COM1] 經由串口來遠端遙控管理 Windows Server 系統。設置值有:[COM1] [COM2] Terminal Type [VT-UTF8] 此為微軟 Windows Emergency Management Services (EMS) 提供 Windows S e r v e r 操作系統可以通過串口來採用遠端遙控管理。設置值有:V T100] [VT100+] [VT-UTF8
5.5.
5.5.
5.5.
PCIE OPROM Slot Options PCIE1-3 Slot OPROM [Enabled] 啟用或關閉 PCIe 插槽的 OPROM。設置值有:[Disabled] [Enabled] MEZZ1 Slot OPROM [Enabled] 啟用或關閉 MEZZ 插槽的 OPROM。設置值有:[Disabled] [Enabled] 5.5.9 USB 設置(USB Configuration) Legacy USB Support [Enabled] 啟用或關閉支持 Legacy USB 設備。設置值有:[Enabled] [Disabled] [Auto] USB Mass Storage Driver Support [Enabled] 本項目提供您啟用或關閉支持 U S B 大量存儲設備。設置值有:[D i s a b l e d] [Enabled] Mass Storage Devices AMI Virtual CDROM0-2 / Floppy / HDisk0 1.
5.5.
5.5.11 NVMe 設置 本菜單提供 NVMe 控制器與驅動程序信息。 5.5.
5.5.13 iSCSI 設置 本菜單提供設置 iSCSi 參數。 5.6 平台設置菜單(Platform Configuration menu) IntelRCSetup 菜單提供更改平台設置。 5.6.
PCI Express Configuration PCI-E ASPM Support (Global) [L1 Only] 提供您選擇 ASPM 支援的下游設備。設置值有:[Per individual port] [L1 Only] PCH DMI ASPM [Platform-POR] 提供您啟用或關閉 PCH DMI ASPM 功能。設置值有:[Platform-POR] [ASPM L1] [Disabled] PCH SATA Configuration SATA Controller [Enabled] 啟用或關閉 SATA 控制器。設置值有:[Disabled] [Enabled] Configure sSATA as [AHCI] 提供您識別 SATA 接口為連接 Solid State Drive(SSD)硬盤或硬盤設備。設 置值有:[IDE] [AHCI] [RAID] Support Aggressive Link Power Management [Enabled] 啟用 Suport Aggressive Link Power (SALP) 管理功能。設置值有:[Disa
以下的項目僅當 xHCI Manual Mode 設置為 [Enabled] 時才會顯示。 Trunk Clock Gating (BTCG) [Enabled] 啟用或關閉 BTCG。設置值有:[Disabled] [Enabled] Enable USB 3.0 pins [Disable all pins] 啟用或關閉 U S B 3.
5.6.2 Miscellaneous 設置 Active Video [Offboard Device] 提供您選擇視頻類型。設置值有:[Onboard Device] [Offboard Device] 5.6.
5.6.4 Runtime Error Logging Support Runtime Error Logging System Errors [Enabled] 啟用或關閉 System Errors。設置值有:[Disabled] [Enabled] Whea Setting Whea Support [Disabled] 啟用或關閉 WHEA 支持。設置值有:[Disabled] [Enabled] 5.
5.7.
DCU Streamer Prefetcher [Enabled] 本項目為啟用或關閉 L1 數據 prefetcher。設置值有:[Disabled] [Enabled] DCU IP Prefetcher [Enabled] 本項目提供您啟用或關閉下一個基於隨著在載入記錄之上的 L1 線。設置值有: [Disabled] [Enabled] LLC Prefetch [Disabled] 本項目提供您啟用或關閉 LLC Prefetch。設置值有:[Disabled] [Enabled] DCU Mode [32K 8Way Without ECC] 設置值有:[32K 8Way Without ECC] [16K 4Way With ECC] Extended APIC [Disabled] 本項目提供您啟用或關閉延伸 APIC 支持。設置值有:[Disabled] [Enabled] AES-NI [Enabled] 本項目提供您啟用或關閉 AES-NI 支持。設置值有:[Disabled] [Enabled] 5.7.
5.7.3 UPI 設置 UPI General Configuration UPI Status 本項目為顯示有關 UPI 狀態的相關信息。 Link Speed Mode [Fast] 本項目為提供設置 UPI 連接速度為任一快速模式(fast mode)或慢速模式(slow mode)。設置值有:[Slow] [Fast] Link Frequency Select [Auto] 本項目為提供設置 UPI 連接頻率。設置值有:[Auto] [9.6 GB/s] [10.
5.7.
Rank Interleaving [Auto] 選擇不同的 rank interleaving 設置。設置值有:[Auto] [1-way Interleave] [2way Interleave] [4-way Interleave] [8-way Interleave] Memory RAS Configuration Mirror Mode [Disabled] 本項目提供您選擇 Mirror Modes。Mirror Mode 會設置所有 1LM/2LM 內存 鏡射,以使內存容量減半。開啟 Mirror Mode 將會關閉 XPT Prefetch。設置值 有:[Disabled] [Mirror Mode 1LM] [Mirror Mode 2LM] UEFI ARM Mirror [Disabled] 啟用或關閉 UEFI ARM Mirror。設置值有:[Disabled] [Enabled] Memory Rank Sparing [Disabled] 啟用或關閉 Memory Rank Sparing 功能。設置值有:[Disabled] [Enabled] Patrol Scru
5.7.
5.7.
CPU - Advanced PM Tuning Energy Perf BIAS Power Performance Tuning [OS Controls EPB] 設置值有:[OS Controls EPB] [BIOS Controls EPB] 以下的項目僅當 Power Performance Tuning 設置為 [OS Controls EPB] 時才會顯示。 PECI PCS EPB [OS Controls EPB] 本項目用來控制是否 PECI 決定 EPB。設置值有:[OS Controls EPB] [PECI Controls EPB using PCS] 以下的項目僅當 P o w e r P e r f o r m a n c e T u n i n g 設置為 [B I O S Controls EPB] 時才會顯示。 ENERGY_PERF_BIAS_CFG Mode [Balanced Performance] 設置值有:[Performance] [Balanced Performance] [Balanced Power] [Power] Dynamic Loa
5.8 事件記錄菜單(Event Logs menu) 5.8.1 更改 Smbios 事件記錄設置 按下 鍵以更改 Smbios 事件記錄設置。 更改的數值會在重新啟動後才生效。 Enabling/Disabling Options Smbios Event Log [Enabled] 啟用或關閉所有在啟動過程中的 Smbios Event 記錄功能。設置值有:[Disabled] [Enabled] Erasing Settings Erase Event Log [No] 本項為提供選擇清除 Smbios Event Log 的選項,在重新啟動時清除在任何載入任 何記錄動作。設置值有:[No] [Yes, Next reset] [Yes, Every reset] 5.8.
5.
5.10 安全性菜單(Security menu) 本菜單可以讓您更改系統安全設置,並且提供您啟用或關閉安全啟動(S e c u r e Boot)狀態與讓用戶設置系統模式(System Mode)狀態。 Administrator Password(設置系統管理員密碼) 當您設置系統管理員密碼後,推薦您先登入您的帳戶,以免 BIOS 設置程序中的某 些信息無法查看或更改設置。 請依照以下步驟設置系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 C r e a t e N e w P a s s w o r d 窗口輸入欲設置的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟更改系統管理員密碼(Administrator Password): 1. 請選擇 Administrator Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3.
User Password(設置用戶密碼) 當您設置用戶密碼後,你必需登入您的帳戶才能使用 BIOS 設置程序。用戶密碼的 默認值為 Not Installed,當您設置密碼後將顯示 Installed。 請依照以下步驟設置用戶密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 C r e a t e N e w P a s s w o r d 窗口輸入欲設置的密碼,輸入完成時,請按下 。 3. 請再一次輸入密碼以確認密碼正確。 請依照以下步驟更改用戶密碼(User Password): 1. 請選擇 User Password 項目並按下 。 2. 由 Enter Current Password 窗口輸入密碼並按下 。 3. 由 Create New Password 窗口輸入新密碼,輸入完成按下 。 4.
5.
5.
5.
第六章: 磁盤陣列設置 在本章節中,我們將介紹關於服務器的磁盤陣列的設置 與說明。 6
6.1 RAID 功能設置 本系統提供以下的 SATA RAID 解決方案: ‧ I ntel® Rapid Storage Technology enterprise SATA Option ROM 工具程序, 可以讓您創建 RAID 0、RAID 1、RAID 10 和 RAID 5 磁盤數組設置(適用於 Windows 及 Linux 操作系統)。 6.1.
6.1.2 安裝硬盤 本主板支持 Serial ATA 硬盤。為了最佳的性能表現,當您要創建數組模式設置 時,請盡可能採用具備相同型號與容量的硬盤。 請依照以下安裝方式來安裝 SATA 硬盤至硬盤槽裡。 1. 將硬盤安裝至硬盤槽中。 2. 安裝硬盤連接排線,將欲建構磁盤數組的硬盤連接至主板。 3. 將 SATA 電源線連接到每一部硬盤。 6.1.3 在 BIOS 程序中設置 RAID 在您開始創建數組之前,您必須先在 BIOS 程序設置中設置對應的 RAID 選項。請 依照下列步驟進行操作︰ 1. 在啟動後系統仍在進行開機自檢(P o w e r-O n S e l f T e s t,P O S T)時,按下 按鍵進入 BIOS 設置程序。 2. 進入 Platform Configuration Menu > PCH Configuration > PCH SATA Configuration 後,按下 鍵。 3. 將 Configuration sSATA as 選項設置為 [RAID Mode]。 4.
6.2 I ntel® Rapid Storage Technology enterprise SATA/ SSATA Option ROM 工具程序 Intel® Rapid Storage Technology enterprise SATA/SSATA Option ROM 工具程 序經由南橋芯片的支持,可讓您使用安裝在系統中的 Serial ATA 硬盤創建 RAID 0、 RAID 1、RAID 10(1+0)與 RAID 5 設置。 在您進行前,請確認您已裝妥 Serial ATA 硬盤,並且調整好正確的主板 跳線設置,然後在 BIOS 程序中設置正確的 SATA 模式。 請依照下列步驟,進入 Intel® Rapid Storage Technology enterprise SATA/SSATA Option ROM 程序: 1. 啟動您的電腦。 2. 當系統運行開機自檢(POST)時,按下 + 按鍵進入程序的主菜單。 Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.
6.3.1 創建 RAID 設置 請依照下列步驟創建一個 RAID 設置: 1. 從主菜單畫面中選擇 1. Create RAID Volume,然後按下 <Enter> 鍵,會出現 如下圖所示的畫面。 2. 為您的 RAID 鍵入一個名稱,然後按下 鍵。 Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. [ CREATE VOLUME MENU ] Name: Volume0 RAID Level: RAID0(Strips) Disks: Select Disks Strip Size: 128KB Capacity: 0.
6. 使用向上/向下方向鍵來選擇磁盤數組的 stripe 大小(只支持 RAID 0、10 與 5 設置時使用),然後按下 鍵。其數值可由 4KB 遞增至 128KB。本項目 推薦依照以下的使用需求,以進行正確的設置。 ·RAID 0:128KB ·RAID 10:64KB ·RAID 5:64KB 若您所使用的是服務器,推薦選擇較低的數組區塊大小;若是用於處理音 樂、圖像剪輯的多介質電腦系統,則推薦選擇較高的數組區塊大小。 7. 選擇 Capacity 項目,輸入您所要的數組容量,接著按下 鍵。本項目默認 值是採用最高可容許的容量。 8. 在 Create Volume 的提示對話框中,再按下 鍵來創建磁盤數組,接著便 會出現如下圖的警告信息畫面。 9. 按下 來創建數組並回到主菜單,或是按下 鍵,回到 CREATE ARRAY (創建數組)菜單。 WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
6.2.2 刪除 RAID 磁區 在操作此功能時請務必非常小心,所有在硬盤中的數據將被刪除。 請依照下列步驟刪除 RAID 磁區︰ 1. 選擇 2. Delete RAID Volume 選項後,按下 鍵進入設置畫面。 2. 使用向上、向下方向鍵選擇您所要刪除的數組後,按下 鍵刪除 RAID 磁 區。在按下確認後,會出現如下圖所示的確認畫面。 Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. [ DELETE VOLUME MENU ] Name Volume0 Level RAID0(Stripe) Drives 2 Capacity 298.
6.2.3 重新設置硬盤為非數組硬盤 請注意!當您將 RAID 數組硬盤設置為無 RAID 數組狀態時,所有磁盤 數組中的數據與數組本身的結構數據都將被移除。 請依照下列步驟重新設置 RAID 硬盤。 1. 選擇選項 3. Reset Disks to Non-RAID 後,按下 鍵以顯示以下的畫面。 2. 使用向上/向下方向鍵選擇您所想要重新設置的所有 RAID 硬盤組,並按下 <空 白> 鍵確認。再按下 鍵重新設置 RAID 硬盤組。接著會顯示一個確認信 息。 [ RESET RAID DATA ] Resetting RAID disk will remove its RAID structures and revert it to a non-RAID disk. WARNING: Resetting a disk causes all data on the disk to be lost.
6.2.4 退出 Intel Rapid Storage Technology enterprise 程序 請依照下列步驟退出應用程序︰ 1. 在應用程序主菜單中,請選擇 4. Exit 然後按下 鍵,會出現如下所示的 畫面。 [ CONFIRM EXIT ] Are you sure you want to exit? (Y/N): 2. 請按下 鍵以退出程序,或按下 鍵回到功能設置主菜單。 6.2.5 修復 RAID 磁盤數組 此選項支持 RAID1、RAID 5 和 RAID 10 設置。 使用非 RAID(Non-RAID)硬盤修復 RAID 磁盤數組 若有任何在 RAID 1 數組設置中的 SATA 硬盤發生損壞時,系統會在開機自檢 (POST)進行時,顯示該 RAID 狀態為“Degraded”,您可以使用其他已經安裝的 非 RAID 硬盤來重建該 RAID 設置。 請依照以下步驟,使用非 RAID(Non-RAID)硬盤修復 RAID 磁盤數組: 1.
3. 選定之後,程序會立即開始進行重建,並且顯示該 RAID 的狀態為“Rebuild”。 Intel(R) Rapid Storage Technology enterprise - SATA Option ROM - 3.6.0.1023 Copyright(C) 2003-12 Intel Corporation. All Rights Reserved. 1. Create RAID Volume 2. Delete RAID Volume RAID Volumes: ID Name 1 Volume0 [ MAIN MENU ] 3. Reset Disks to Non-RAID 4. Exit [ DISK/VOLUME INFORMATION] Level1 RAID1(Mirror) Physical Devices: Port Drive Model 1 ST3160812AS 2 ST3160812AS Strip N/A Serial # 9LS0F4HL 3LS0JYL8 Size 149.0GB Size 149.0GB 149.
6.2.6 在 BIOS 程序中設置啟動數組 當您使用 Intel® Rapid Storage Technology enterprise SCU/SATA Option ROM 創 建多重 RAID(multi-RAID)時,您可以將您所設置的 RAID 數組於 BIOS 程序中設置 啟動優先順序。 請依照以下的步驟,於 BIOS 程序中設置啟動數組: 請從硬盤中至少設置一個啟動數組。 1. 請在開機自檢(POST) 時,按下 鍵進入 BIOS 程序設置畫面。 2. 進入 Boot 菜單,然後選擇 Boot Device Priority 項目。 3. 使用向上/向下方向鍵,選擇啟動順序後按下 鍵,請參考 5.10 啟動菜單 (Boot Menu)的說明。 4. 從 Exit 菜單中,選擇 Save Changes & Exit,然後按下 鍵。 5.
6.3 Intel® Rapid Storage Technology enterprise 工具程序 (Windows) The Intel® Rapid Storage Technology enterprise 工具程序提供您使用安裝在系統 中的 Serial ATA / SAS 硬盤設備創建 RAID 0、RAID 1、RAID 10(1+0)與 RAID 5 設置。 在 Windows 操作系統環境中,進入 Intel® Rapid Storage Technology enterprise 程 序: 1. 啟動並進入操作系統桌面。 2.
6.3.1 創建 RAID 設置 請依照以下步驟創建 RAID 設置: 1. 在前面的主菜單畫面中,點擊 Create Volume 並選擇 volume 類型。 2. 點擊 Next 繼續。 3. 輸入欲創建 RAID 設置的名稱,然後選擇數組要用的磁盤。 4. 選擇 Volume Size 字段,您可以拖曳畫面中的橫桿以決定容量大小。 5.
6. 確認創建,請點擊 Create Volume 繼續。 創建的過程會因數量與容量不同而需要等候一段時間,在此期間,您可 以繼續使用其他的應用程序。 7.
6.3.2 更改 Volume 類型 當您完成創建 RAID 設置時,您可以在 Volume Properties 字段中查看或更改裡頭 的各個項目。 您可以根據以下步驟更改 Volume Properties 的類型: 1.
3. 如有需要,您也可以在此更改 Name、Select the new volume type 與Select additional disks to include in the new volume 這幾個項目。 4.
6.3.3 刪除 Volume 在操作此功能時請務必非常小心,所有在硬盤中的數據將被一併刪除, 如有需要請先備份文件。 請依照以下步驟刪除 Volume: 1. 在主菜單裡,點擊在 Volume 字段中欲刪除的 Volume(如以下畫面中顯示的 Volume_0000)。 2. 然後點擊 Volume Properties 字段中的 Delete volume,則會顯示如下的畫面。 3.
6.3.
第七章: 安裝驅動程序 在本章節中將介紹服務器內的相關驅動程序的安裝與設 置說明。 7
7.1 安裝 RAID 驅動程序 當您在系統中創建好 RAID 數組模式後,現在您就可以開始安裝操作系統至獨立的 硬盤設備或具啟動功能的磁盤數組。這章節將來介紹在安裝操作系統的過程中如何安 裝 RAID 控制器的驅動程序。 7.1.1 創建搭載 RAID 驅動程序的 U 盤 安裝 Windows® Server 操作系統時,您可以由 U 盤載入 RAID 驅動程序。請將文 件由驅動及應用程序光盤複製至 U 盤。 在 Windows® 中創建搭載 RAID 驅動程序的 U 盤: 1. 在光驅中放入本系統/主板的驅動及應用程序光盤。 2. 將 U 盤連接電腦。 3. 開啟驅動及應用程序光盤。 4. 點擊 Drivers > C620 INTEL RAID > Driver > Windows,將 SATA_RAID 文件夾 複製至 U 盤。 7.1.2 安裝 RAID 驅動程序 在 Windows® Server 2012 R2 系統安裝過程中安裝 您可以在 Windows® Server 2012 R2 系統安裝過程中安裝 RAID 驅動程序: 1.
3. 接著請點擊 Load Driver。 4. 然後顯示信息,提醒您放入 R A I D 控制器驅動程序文件。若您的系統裡有僅只 有一部光驅,請先將 Windows 操作系統安裝光盤退出,並放入驅動與應用程序 DVD 光盤,然後點擊 Browse(瀏覽)。 5. 找到存放在驅動與應用程序光盤內的驅動程序,然後點擊 OK 繼續。 6.
7. 當系統載入 R A I D 驅動程序後,請取出主板驅動與應用程序光盤 並再放入 Windows Server 操作系統安裝光盤,選擇驅動程序安裝至 Windows 並點擊 Next。 8.
7.2 安裝應用程序與工具程序 本驅動及應用程序光盤裡提供您主板相關的驅動程序、管理應用程序與工具程序, 可以讓您將主板功能最佳化。 1. 驅動及應用程序 DVD 光盤裡的內容如有更改,恕不另行通知。請訪 問華碩網站(www.asus.com.cn)以更新最新的軟件與工具程序。 2. 驅動及應用程序 DVD 光盤為支持使用於 Windows® Server 2012 R2 R2 和 Windows® Server 2016 操作系統。 7.3 使用驅動及應用程序 DVD 光盤 於光驅中放入主板/系統的驅動程序光盤。若您已經啟動光盤自動檢測的功能,通 過操作系統自動檢測的功能,接著會自行啟動光盤並顯示默認的 Drivers (驅動程 序)標籤頁。 若窗口並未自動出現,那麼請瀏覽驅動及應用程序 D V D 光盤的文件內 容,找到 BIN 目錄中的 ASSETUP.EXE 程序,並點擊 ASSETUP.EXE 主 程序來開啟菜單畫面。 在驅動及應用程序 DVD 光盤的主菜單裡有以下幾個標籤頁: 1. Drivers 2. Utilities 3. Manual 4.
7.3.1 驅動程序主菜單 驅動程序主菜單提供了您當前需要安裝的一些硬件驅動程序,請安裝必要的驅動程 序來啟動您系統上的硬件。 7.3.
7.3.3 用戶手冊菜單 您需要在操作系統中使用網絡瀏覽器軟件才能開啟用戶手冊。 7.3.
7.4 安裝 Intel 芯片設備軟件驅動程序 本章節提供您如何安裝在 Intel 芯片環境中的即插即用設備元件。 您需要在 Windows® 操作系統環境中,手動安裝 Intel® 芯片設備軟件。 請依照以下步驟,在 Windows® 操作系統下安裝 Intel®芯片設備軟件驅動程序: 1. 重新啟動,並使用 Administrator(主管理者)登入 Windows 系統。 2. 將驅動及應用程序 DVD 光盤放入光驅中。 若您已經啟動光盤自動檢測的功能,通過操作系統自動檢測的功能,會自行啟動 光盤顯示 Drivers (驅動程序)菜單畫面。 若窗口並未自動出現,那麼請瀏覽驅動及應用程序 D V D 光盤的文件內 容,找到 BIN 目錄中的 ASSETUP.EXE 程序,並點擊 ASSETUP.EXE 主 程序來開啟菜單畫面。 3. 選擇 Intel® Chipset Device Software 後,開始進行安裝。 4.
5. 當顯示 License Agreement(授權同意)說明時,請點擊 Accept 繼續。 6. 接著,瀏覽並閱讀 Readme File Information 後,請點擊 Install 繼續安裝。 7.
7.5 安裝顯示驅動程序 這裡將介紹如何安裝 ASPEED 圖形顯示界面(VGA)驅動程序。 您需要在 Windows® Server 系統中,手動安裝 ASPEED 圖形顯示界面驅動程序。 請依照以下的步驟安裝 ASPEED 圖形顯示界面驅動程序: 1. 重新啟動,並使用 Administrator(主管理者)登入 Windows 系統。 2. 將驅動及應用程序 DVD 光盤放入光驅中。 若您已經啟動光盤自動檢測的功能,通過操作系統自動檢測的功能,會自行啟動 光盤顯示 Drivers (驅動程序)菜單畫面。 若窗口並未自動出現,那麼請瀏覽驅動及應用程序 D V D 光盤的文件內 容,找到 BIN 目錄中的 ASSETUP.EXE 程序,並點擊 ASSETUP.EXE 主 程序來開啟菜單畫面。 3. 點擊在 Drivers(驅動程序)菜單裡的 ASPEED AST2500 Display Driver 開始安 裝。 4.
5. 點擊 Install 以繼續安裝。 6.
7.6 安裝 Intel® I350-AM2 Gigabit 界面驅動程序 本節介紹如何安裝 Intel® I350-AM2 Gigabit 驅動程序至系統中。 您需要在 Windows® 操作系統環境中,手動安裝網絡驅動程序。 請依照以下的步驟在 Windows® 操作系統中,安裝 Intel® I350-AM2 Gigabit 驅動 程序: 1. 重新啟動,並使用 Administrator(主管理者)登入 Windows 系統。 2. 將驅動及應用程序 DVD 光盤放入光驅中。 若您已經啟動光盤自動檢測的功能,通過操作系統自動檢測的功能,會自行啟動 光盤顯示 Drivers (驅動程序)菜單畫面。 若窗口並未自動出現,那麼請瀏覽驅動及應用程序 D V D 光盤的文件內 容,找到 BIN 目錄中的 ASSETUP.EXE 程序,並點擊 ASSETUP.EXE 主 程序來開啟菜單畫面。 3. 點擊 Intel® I350-AM2 Gigabit Adapter Driver 項目開始安裝。 4.
5. 點擊 Install 進行安裝。 6.
7.7 安裝 Intel® Rapid Storage Technology enterprise 程序 本節將介紹如何安裝 Intel® Rapid Storage Technology enterprise 程序。 您需要在 W i n d o w s S e r v e r 系統中,以手動方式安裝 I n t e l ® R a p i d S t o r a g e Technology enterprise 程序。 請依照以下步驟安裝程序: 1. 重新啟動,並使用 Administrator(主管理者)登入 Windows 系統。 2. 於光驅中放入主板/系統所附的驅動與應用程序光盤,,點擊 Utilities。 3. 點擊 Intel® Rapid Storage Technology enterprise 開始安裝。 4.
5. 讀取警示信息後,點擊 Next 繼續。 6. 選擇 Accept 接受許可同意條款,並且繼續安裝進程。 7.
8. 選擇欲安裝的功能後點擊 Next。 9. 點擊 Install 進行安裝作業。 10.
附錄 本附錄為提供您參考的相關聯絡信息。
Z11PR-D16 架構圖 DDR4 AEP DIMM/RDIMM * 2 Channel G DDR4 1866/2133/2400/2667 Channel A DDR4 1866/2133/2400/2667 DDR4 AEP DIMM/RDIMM * 1 Channel H DDR4 1866/2133/2400/2667 Channel B DDR4 1866/2133/2400/2667 DDR4 AEP DIMM/RDIMM * 1 DDR4 AEP DIMM/RDIMM * 1 Channel J DDR4 1866/2133/2400/2667 Channel C DDR4 1866/2133/2400/2667 DDR4 AEP DIMM/RDIMM * 1 DDR4 AEP DIMM/RDIMM * 2 Channel K DDR4 1866/2133/2400/2667 CPU2 CPU1 Channel D DDR4 1866/2133/2400/2667 DDR4 AEP DIMM/RDIMM * 1 Channel L DDR4 1866/213
華碩的聯絡信息 華碩電腦公司 ASUSTeK COMPUTER INC.(台灣) 市場信息 地址 :台灣臺北市北投區立德路 150 號 4 樓 電話 :+886-2-2894-3447 傳真 :+886-2-2890-7798 網址 :http://www.asus.com/tw/ 技術支持 電話 在線支持 :+886-2-2894-3447(0800-093-456) : https://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=zh-tw 華碩電腦(上海)有限公司 ASUSTEK COMPUTER(SHANGHAI)CO., LTD. 市場信息 地址 : 上海市閔行區金都路 5077 號 電話 :+86-21-5442-1616 傳真 :+86-21-5442-0099 網址 :http://www.asus.com.
ASUS COMPUTER GmbH(德國/奧地利) 市場信息 地址 :Harkortstr. 21-23, 40880 Ratingen, Deutschland 傳真 :+49-2102-959911 網址 :http://www.asus.com/de/ 技術支持 電話 :+49-1805-010923 傳真 :+49-2102-9599-11 在線支持 : https://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=de-de * 從德國撥號採固網的費率每分鐘 0.14 歐元;行動電話的費率每分鐘 0.42 歐元。 ASUS Czech Service s.r.o.(歐洲) 市場信息 地址 :Na Rovince 887, 720 00 Ostrava – Hrabová, Czech Republic 傳真 :+420-596766888 網址 :http://www.asus.
ASUS Holland BV(荷蘭) 市場信息 地址 網址 :Marconistraat 2, 7825GD EMMEN, The Netherlands :http://www.asus.com/nl/ 技術支持 電話 :+31-(0)591-5-70292 傳真 :+31-(0)591-666853 電子信箱 :advance.rma.eu@asus.com 在線支持 : https://www.asus.com/support/Product/ContactUs/ Services/questionform/?lang=nl-nl ASUS Polska Sp. z o.o.(波蘭) 市場信息 地址 網址 技術支持 電話 在線支持 :Ul. Postępu 6, 02-676 Warszawa, Poland :http://www.asus.com/pl/ :+48-225718033 : https://www.asus.