User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-39
ASUS RS520A-E11-RS12U
PPIN Opt-in [Auto]
Allows you to enable or disable the PPIN feature.
Configuration options: [Disabled] [Enabled] [Auto]
SNP Memory (RMP Table) Coverage [Auto]
Setting this option to [Enabled] will cover the entire system’s memory.
Configuration options: [Disabled] [Enabled] [Custom] [Auto]
The following item appears only when SNP Memory (RMP Table) Coverage is set to
[Custom].
Amount of Memory to Cover [0]
Allows you to specify MB of System Memory to be covered in Hex.
SMEE [Auto]
Allows you to enable or disable secure memory encryption control.
Configuration options: [Disabled] [Enabled] [Auto]
Action on BIST Failure [Auto]
Allows you to set action to take when a CCD BIST failure is detected.
Configuration options: [Do Nothing] [Down-CCD] [Auto]
Fast Short REP MOVSB [Enabled]
Default set to 1, can be set to zero for analysis purposes as long as OS supports it.
Configuration options: [Disabled] [Enabled]
Enhanced REP MOVSB/STOSB [Enabled]
Default set to 1, can be set to zero for analysis purposes as long as OS supports it.
Configuration options: [Disabled] [Enabled]
REP-MOV/STOS Streaming [Enabled]
Allows REP-MOVS/STOS to use non-caching streaming stores for large sizes.
Configuration options: [Disabled] [Enabled]
X3D [Auto]
Allows you to set the override of X3D technology.
Configuration options: [Auto] [Disable] [1 stack] [2 stacks] [4 stacks]
IBS hardware workaround [Auto]
Set this option if using IBS execution sampling without software workaround for erratum
1,285. May impact performance.
Configuration options: [Auto] [Enabled]