User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-41
ASUS RS520A-E11-RS12U
1TB remap [Auto]
Attempt to remap DRAM out of the space just below the 1TB boundary. The ability to
remap depends on DRAM configuration, NPS, and interleaving selection, and may not
always be possible.
Configuration options: [Do not remap] [Attempt to remap] [Auto]
DRAM map inversion [Auto]
Inverting the map will cause the highest memory channels to get assigned the lowest
addresses in the system.
Configuration options: [Disabled] [Enabled] [Auto]
Location of private memory regions [Auto]
Controls whether or not the private memory regions (PSP, SMU, and CC6) are at the
top of DRAM or distributed. Note that distributed requires memory on all dies. Note that
it will always be at the top of DRAM id some dies don’t have memory regardless of this
option’s setting.
Configuration options: [Distributed] [Consolidated] [Consolidated to 1st DRAM pair]
[Auto]
ACPI
ACPI SRAT L3 Cache As NUMA Domain [Auto]
[Disabled] Memory Addressing \ NUMA nodes per socket will be declared.
[Enabled] Each CCX in the system will be declared as a separate NUMA Domain.
[Auto] Auto.
ACPI SLIT Distance Control [Auto]
This option determines how the SLIT distances are declared.
Configuration options: [Manual] [Auto]
The following item appears only when ACPI SLIT Distance Control is set to [Auto].
ACPI SLIT remote relative distance [Auto]
Allows you to set the remote socket distance for 2P systems as near (2.8) or far (3.2).
Configuration options: [Near] [Far] [Auto]
The following items appear only when ACPI SLIT Distance Control is set to [Manual].
ACPI SLIT same socket distance [C]
Specify the distance to other physical domains within the same socket.
ACPI SLIT remote socket distance [20]
Specify the distance to domains the remote socket.
ACPI SLIT local SLink distance [32]
Specify the distance to an SLink domain on the same socket.
ACPI SLIT remote SLink distance [3C]
Specify the distance to an SLink domain on the other socket.