User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-43
ASUS RS520A-E11-RS12U
Disable DF sync flood propagation [Auto]
Allows you to enable or disable propagation from PIE to other DF components and eventually
to SDP ports.
Configuration options: [Sync Flood disabled] [Sync Flood enabled] [Auto]
Freeze DF module queues on error [Auto]
Allows you to enable or disable freezing of all DF queues on error and also forces a sync
flood on HWA even if MCAs are disabled.
Configuration options: [Disabled] [Enabled] [Auto]
CC6 memory region encryption [Auto]
Allows you to control whether or not the CC6 save/restore memory is encrypted.
Configuration options: [Disabled] [Enabled] [Auto]
System probe filter [Auto]
Allows you to control whether or not the probe filter is enabled. Has no effect on parts where
the probe filter is fuse disabled.
Configuration options: [Disabled] [Enabled] [Auto]
Memory Clear [Auto]
Allows you to enable or disable memory clear. When this item is set to [Disabled], BIOS does
not implement MemClear after memory training (only if non-ECC DIMMs are used).
Configuration options: [Disabled] [Enabled] [Auto]
PSP error injection support [False]
Configuration options: [False] [True]
5.11.3 UMC Common Option
DDR4 Common Options
DRAM Timing Configuration
Allows you to enable DRAM timing configuration.
Damage caused by use of your AMD processor outside of specification or in excess of
factory settings are not covered by your system manufacturers warranty.