User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-49
ASUS RS520A-E11-RS12U
The following items appear only when you set CAD Bus Timing User Controls to
[Manual].
AddrCmdSetup [0]
Allows you to setup time on CAD bus signals.
Configuration options: [0] – [39]
CsOdtSetup [0]
Allows you to setup time on CAD bus signals.
Configuration options: [0] – [39]
CkeSetup [0]
Allows you to setup time on CAD bus signals.
Configuration options: [0] – [39]
CAD Bus Drive Strength User Controls [Auto]
Allows you to set the CAD bus signals to Auto or Manual.
Configuration options: [Auto] [Manual]
The following items appear only when you set CAD Bus Drive Strength User Controls to
[Manual].
ClkDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
AddrCmdDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
Cs0dtDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
CkeDrvStren [Auto]
Configuration options: [Auto] [120.0 Ohm] [60.0 Ohm] [40.0 Ohm] [30.0
Ohm] [24.0 Ohm] [20.0 Ohm]
Data Bus Configuration
Data Bus Configuration User Controls [Auto]
Allows you to specify the mode for drive strength.
Configuration options: [Auto] [Manual]
The following items appear only when you set Data Bus Configuration User Controls to
[Manual].
RttNom [Auto]
Configuration options: [Rtt_Nom Disable] [RZQ/4] [RZQ/2] [RZQ/6] [RZQ/1]
[RZQ/5] [RZQ/3] [RZQ/7] [Auto]
RttWr [Auto]
Configuration options: [Dynamic ODT Off] [RZQ/2] [RZQ/1] [Hi-Z] [RZQ/3]
[Auto]
RttPark [Auto]
Configuration options: [Rtt_PARK Disable] [RZQ/4] [RZQ/2] [RZQ/6]
[RZQ/1] [RZQ/5] [RZQ/3] [RZQ/7] [Auto]