User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-52
Chapter 5: BIOS Setup
Memory MBIST
MBIST Enable [Disabled]
Allows you to enable or disable Memory MBIST.
Configuration options: [Enabled] [Disabled]
The following items appear only when MBIST Enable is set to [Enabled].
MBIST Test Mode [Auto]
Allows you to select the MBIST Test Mode - Interface Mode (Tests Single and Multiple
CS transactions and Basic Connectivity) or Data Eye Mode (Measures Voltage vs.
Timing).
Configuration options: [Interface Mode] [Data Eye Mode] [Both] [Auto]
MBIST Aggressors [Auto]
Allows you to enable or disable Memory Aggressor test.
Configuration options: [Enabled] [Disabled] [Auto]
MBIST Per Bit Slave Die Reporting [Auto]
Reports 2D Data Eye Results in ABL Log for each DQ, Chipselect, and Channel.
Configuration options: [Enabled] [Disabled] [Auto]
Data Eye
Pattern Select [PRBS]
Configuration options: [PRBS] [SS0] [Both]
Pattern Length [3]
This token helps to determine the pattern length. The possible options are
N=3...12.
Configuration options: [3] – [9]
Aggressor Channel [1 Aggressor Channel]
This helps read the aggressors channels. If set to [Enabled], you can
read from one or more than one aggressor channel. The default is set to
[Disabled].
Configuration options: [Disabled] [1 Aggressor Channel] [3 Aggressor
Channels] [7 Aggressor Channels]
Aggressor Static Lane Control [Disabled]
Configuration options: [Disabled] [Enabled]
The following items appear only when Aggressor Static Lane Control is set to [Enabled].
Aggressor Static Lane Select Upper 32 bits [0]
Static Lane Select for Upper 32 bits. The bit mask represents the bits to be
read.
Configuration options: [0] - [99999999]
Aggressor Static Lane Select Lower 32 bits [0]
Static Lane Select for Lower 32 bits. The bit mask represents the bits to be
read.
Configuration options: [0] - [99999999]