User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-57
ASUS RS520A-E11-RS12U
xGMI Max Link Width Control [Auto]
[Auto] Use default xGMI max supported link width.
[Manual] User can set custom xGMI max link width.
The following item appears only when xGMI Max Link Width Control is set to [Manual].
xGMI Max Link Width [1]
[0] Set max xGMI link width to x8.
[1] Set max xGMI link width to x16.
APBDIS [Auto]
[0] Not APBDIS (mission mode)
[1] APBDIS
[Auto] Auto
DF Cstates [Auto]
Allows you to enable or disable DF C-states.
Configuration options: [Disabled] [Enabled] [Auto]
CPPC [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
HSMP Support [Auto]
This option allows you to enable or disable HSMP support.
Configuration options: [Disabled] [Enabled] [Auto]
DLWM Support [Auto]
This option allows you to enable or disable DLWM support.
Configuration options: [Disabled] [Enabled] [Auto]
Boost FmaxEn [Auto]
[Auto]
Use the default Fmax.
[Manual] User can set the boost Fmax.
The following item appears only when Boost FmaxEn is set to [Manual].
BoostFmax [0]
Allows you to specify the boost Fmax frequency limit to apply to all cores (MHz).
EDC Current Tracking [Disable]
The generation of a correctable MCE when the telemetry current value is over the set
threshold defined by EDC Current Tracking Current Threshold.
Configuration options: [Disable] [Enable]
The following items appears only when EDC Current Tracking is set to [Enable].
EDC Tracking Current Threshold [0]
The current threshold in AMPs for EDC Current Tracking feature.