User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-59
ASUS RS520A-E11-RS12U
NBIO RAS Common Options
NBIO RAS Control [Auto]
Configuration options: [Disabled] [MCA] [Legacy] [Auto]
Egress Poison Severity High [30011]
Each bit set to 1 enables HIGH severity on the associated IOHC egress port. A bit of 0
indicates LOW severity.
Egress Poison Severity Low [4]
Each bit set to 1 enables HIGH severity on the associated IOHC egress port. A bit of 0
indicates LOW severity.
NBIO SyncFlood Generation [Auto]
This value may be used to mask SyncFlood caused by NBIO RAS options. When set
to TRUE, SyncFlood from NBIO is masked. When set to FALSE, NBIO is capable of
generating SyncFlood.
Configuration options: [Disabled] [Enabled] [Auto]
NBIO SyncFlood Reporting [Auto]
This value may be used to enable SyncFlood reporting to APML. When set to TRUE,
SyncFlood will be reported to APML. When set to FALSE, the reporting will be
disabled.
Configuration options: [Disabled] [Enabled] [Auto]
Egress Poison Mask High [
FFFCFFFF]
These set the enable mask for masking of errors logged in EGRESS_POISON_
STATUS. For each bit set to 1, errors are masked. For each bit set to 0, errors trigger
response actions.
Egress Poison Mask Low [FFFFFFFB]
These set the enable mask for masking of errors logged in EGRESS_POISON_
STATUS. For each bit set to 1, errors are masked. For each bit set to 0, errors trigger
response actions.
Uncorrected Converted to Poison Enable Mask High [30000]
These set the enable mask for masking of uncorrectable parity errors on internal
arrays. For each bit set to 1, a system fatal error event is triggered for UCP errors on
arrays associated with that egress port. For each bit set to 0, errors are masked.
Uncorrected Converted to Poison Enable Mask Low [4]
These set the enable mask for masking of uncorrectable parity errors on internal
arrays. For each bit set to 1, a system fatal error event is triggered for UCP errors on
arrays associated with that egress port. For each bit set to 0, errors are masked.
System Hub Watchdog Timer [a28]
This value specifies the timer interval of the SYSHUB Watchdog Timer in milliseconds.