User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-60
Chapter 5: BIOS Setup
SLink Read Response OK [Disabled]
This value specifies whether SLINK read response errors are converted to an Okay
response. When this value is set to TRUE, read response errors are converted to Okay
responses with data of all FFs. When set to FALSE, read response errors are not
converted.
Configuration options: [Disabled] [Enabled]
SLink Read Response Error Handling [Log Errors in MCA]
This value specifies whether SLINK write response errors are converted to an Okay
response. When this value is set to 0, write response errors will be logged in the MCA.
When set to 1, write response errors will trigger an MCOMMIT error. When this value is
set to 2, write response errors are converted.
Configuration options: [Enabled] [Trigger MCOMMIT Error] [Log Errors in MCA]
Log Poison Data from SLINK [Disabled]
This value specifies whether poison data propagated from SLINK will generate a
deferred error. When this value is set to TRUE, deferred errors are enabled. When set
to FALSE, errors are not generated.
Configuration options: [Disabled] [Enabled]
PCIe Aer Reporting Mechanism [Auto]
This value selects the method of reporting AER errors from PCI Express. A value of 0
indicates that the hardware will report the error through MCA. A value of 1 allows OS
First handling of the errors through generation of a system control interrupt (SCI). A
value of 2 allows Firmware First handling of the errors through generation of a system
control interrupt (SCI).
Configuration options: [Firmware First] [OS First] [Auto]
Edpc Control [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
NBIO Poison Consumption [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
Sync Flood on PCIe Fatal Error [Auto]
Configuration options: [Auto] [True] [False]
Enable AER Cap [Auto]
Allows you to enable or disable Advanced Error Reporting Capability.
Configuration options: [Enable] [Disabled] [Auto]
Early Link Speed [Auto]
Allows you to set Early Link Speed.
Configuration options: [Auto] [Gen1] [Gen2]
Hot Plug Handling mode [Auto]
Allows you to control the Hot Plug Handling mode.
Configuration options: [OS First] [Firmware First] [Auto]
Presence Detect Select mode [Auto]
Allows you to control the Presence Detect Select mode.
Configuration options: [OR] [AND] [Auto]