User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-64
Chapter 5: BIOS Setup
Sata7 SGPIO [Auto]
Allows you to enable or disable SataSgpio on Sata7.
Configuration options: [Disabled] [Enabled] [Auto]
USB Configuration Options
XHCI Controller0 enable [Auto]
Allows you to enable or disable USB3 controller.
Configuration options: [Enabled] [Disabled] [Auto]
XHCI Controller1 enable [Auto]
Allows you to enable or disable USB3 controller.
Configuration options: [Enabled] [Disabled] [Auto]
USB ecc SMI Enable [Auto]
MCM USB enable
XHCI2 enable (Socket1) [Auto]
Allows you to enable or disable USB3 controller.
Configuration options: [Disabled] [Enabled] [Auto]
XHCI3 enable (Socket1) [Auto]
Allows you to enable or disable USB3 controller.
Configuration options: [Disabled] [Enabled] [Auto]
SD Dump Options
SD Configuration Mode [SD Dump disabled]
Configuration options: [SD Dump disabled] [SD Dump enabled]
Ac Power Loss Options
AC Loss Control [Always On]
Allows you to select Ac Loss Control Method.
Configuration options: [Always Off] [Always On] [Reserved] [Previous] [Auto]
I2C Configuration Options
I2C 0 Enable [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
I2C 1 Enable [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
I2C 2 Enable [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
I2C 3 Enable [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
I2C 4 Enable [Auto]
Configuration options: [Disabled] [Enabled] [Auto]
I2C 5 Enable [Auto]
Configuration options: [Disabled] [Enabled] [Auto]