User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-68
Chapter 5: BIOS Setup
Socket-0 P3 Link Speed [Auto]
Allows you to select the Link Speed for Socket-0 P3.
Configuration options: [Max Speed] [Gen 1] [Gen 2] [Gen 3] [Auto] [Gen 4]
Socket-0 P3 NTB Mode [Auto]
Allows you to select the NTB Mode for Socket-0 P3 Link.
Configuration options: [Auto] [NTB Disabled] [NTB Primary] [NTB Secondary]
ABL Console Out Control [Auto]
[Disable] Disable ConsoleOut Function for ABL.
[Enable] Enable ConsoleOut Function for ABL.
[Auto] Keep default behavior.
The following items appear only when ABL Console Out Control is set to [Enable].
ABL Basic Console Out Control [Auto]
[Disable] Disable Basic ConsoleOut Function for ABL.
[Enable] Enable Basic ConsoleOut Function for ABL.
[Auto] Keep default behavior.
ABL PMU message Control [Auto]
Allows you to control the total number of PMU debug messages. Several major controls are
listed below:
1. Detailed debug messages (e.g. Eye delays)
2. Coarse debug messages (e.g. rank information)
3. Stage completion
4. Firmware completion message only
Configuration options: [Detailed debug message] [Coarse debug messages] [Stage
completion] [Firmware completion message only] [Auto]
5.11.7 Soc Miscellaneous Control