User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
5-73
ASUS RS520A-E11-RS12U
System Event Log
Allows you to change the SEL event log configuration.
Erase SEL [No]
Allows you to choose options for erasing SEL.
Configuration options: [No] [Yes, On next reset] [Yes, On every reset]
All values changed here do not take effect until computer is restarted.
BMC network configuration
The sub-items in this configuration allow you to configure the BMC network parameters.
Configure IPV4 support
DM_LAN1/
Configuration Address source [Previous State]
Allows you to configure LAN channel parameters statistically or dynamically (by BIOS
or BMC). [Previous State] option will not modify any BMC network parameters during
BIOS phase.
Configuration options: [Previous State] [Static] [DynamicBmcDhcp]
The following items are available only when Configuration Address source is set to
[Static].
Station IP address
Allows you to set the station IP address.
Subnet mask
Allows you to set the subnet mask. We recommend that you use the same Subnet
Mask you have specified on the operating system network for the used network card.
Router IP Address
Allows you to set the router IP address.
Router MAC Address
Allows you to set the router MAC address.Shared LAN
Configure IPV6 support
DM_LAN1
IPV6 Support [Enabled]
Allows you to enable or disable LAN1 IPV6 Support.
Configuration options: [Disabled] [Enabled]