User Manual

Chapter 1: Product Introduction
1-20
Action PHASE POST CODE TYPE DESCRIPTION
PSP Boot
PSP Boot Loader
phase (Status Post
Codes)
0x7B error
0x7C error Platform Vendor ID and/or Model ID binding violation
0x7D error
Bootloader detects BIOS request boot from SPI-ROM, which is unsupported
for PSB.
0x7E error Requested fuse is already blown, reblow will cause ASIC malfunction
0x7F error Error with actual fusing operation
0x80 error (Local Master PSP on P1 socket) Error reading fuse info
0x81 error
(Local Master PSP on P1 socket) Platform Vendor ID and/or Model ID
binding violation
0x82 error
(Local Master PSP on P1 socket) Requested fuse is already blown, reblow
will cause ASIC malfunction
0x83 error (Local Master PSP on P1 socket) Error with actual fusing operation
0x84 error SEV FW Rollback attempt is detected
0x85 error
/ SEV download FW command fail to broadcase and clear the IsInSRAM
field on slave dies
0x86 error Agesa error injection failure
0x87 error Uncorrectable TWIX error detected
0x88 error Error programming the TWIX PCS registers
0x89 error Error setting TWIX PCS threshold value
0x8A error SW CCP queue is full, cannot add more entries
0x8B error CCP command description syntax error detected from input
0x8C error Return value stating that the command has not yet be scheduled
0x8D error The command is scheduled and being worked on
0x8E error The DXIO PHY SRAM Public key certificate loading or authentication fails
0x8F error
fTPM binary size exceeds limit allocated in Private DRAM, need to increase
the limit
0x90 error The TWIX link for a particular CCD is not trained Fatal error
0x91 error Security check failed (not all dies are in same security state)
0x92 error
FW type mismatch between the requested FW type and the FW type
embedded in the FW binary header
0x93 error SVC call input parameter address violation
0x94 error Knoll failed to idle correctly after being reset
0x95 error Bad status returned by I2CKnollCheck
0x96 error NACK to general call (no device on Knoll I2C bus)
0x97 error Null pointer passed to I2CKnollCheck
0x98 error Invalid device-ID found during Knoll authentication
0x99 error Error during Knoll/Prom key derivation
0x9A error Null pointer passed to Crypto function
0x9B error Error in checksum from wrapped Knoll/Prom keys
0x9C error Knoll returned an invalid response to a command
0x9D error Bootloader failed in Knoll Send Command function
0x9E error No Knoll device found by verifying MAC
0x9F error The maximum allowable error post code
Quick VGA
PEI(Pre-EFI
Initialization) phase
0x10 Progress PEI Core Entry
0x11 Progress PEI cache as ram CPU initial
0x15 Progress NB Initialization before installed memory
0x19 Progress SB Initialization before installed memory
DXE(Driver
Execution
Environment)
phase
0x32 Progress CPU POST-Memory Initialization
0x33 Progress CPU Cache Initialization
0x34 Progress Application Processor(s) (AP) Initialization
0x35 Progress BSP Selection
0x36 Progress CPU Initialization
0x37 Progress Pre-memory NB Initialization
0x3B Progress Pre-memory SB Initialization
0x4F Progress DXE Initial Program Load(IPL)
0x60 Progress DXE Core Started
0x61 Progress DXE NVRAM Initialization
0x62 Progress SB run-time Initialization
0x63 Progress CPU DXE Initialization
0x68 Progress PCI HB Initialization
0x69 Progress NB DXE Initialization
0x6A Progress NB DXE SMM Initialization
0x70 Progress SB DXE Initialization
0x71 Progress SB DXE SMM Initialization
0x72 Progress SB DEVICES Initialization
0x78 Progress ACPI Module Initialization
0x79 Progress CSM Initialization
0xD0 Progress CPU PM Structure Initialization
(continued on the next page)