User Manual
Table Of Contents
- Safety information
- Chapter 1: Product Introduction
- Chapter 2: Hardware Information
- 2.1 Chassis cover
- 2.2 Air ducts
- 2.3 Central Processing Unit (CPU)
- 2.4 System memory
- 2.5 Storage devices
- 2.6 Expansion slot
- 2.6.1 Installing an expansion card to the left PCIe riser card bracket
- 2.6.2 Installing an expansion card to the right PCIe riser card bracket
- 2.6.3 Installing a ASUS PIKE II card to the right PCIe riser card bracket
- 2.6.4 Installing an OCP 3.0 card to the OCP 3.0 slot
- 2.6.5 Installing an M.2 (NGFF) card
- 2.6.6 (optional) Installing the PFR module
- 2.6.7 Configuring an expansion card
- 2.7 Cable connections
- 2.8 Backplane cabling
- 2.9 Storage device configuration and cabling
- 2.10 Removable/optional components
- Chapter 3: Installation Options
- Chapter 4: Motherboard Information
- Chapter 5: BIOS Setup
- 5.1 Managing and updating your BIOS
- 5.2 BIOS setup program
- 5.3 Main menu
- 5.4 Performance Tuning menu
- 5.5 Advanced menu
- 5.5.1 Trusted Computing
- 5.5.2 PSP Firmware Versions
- 5.5.3 Redfish Host Interface Settings
- 5.5.4 APM Configuration
- 5.5.5 Onboard LAN Configuration
- 5.5.6 Serial Port Console Redirection
- 5.5.7 CPU Configuration
- 5.5.8 PCI Subsystem Settings
- 5.5.9 USB Configuration
- 5.5.10 Network Stack Configuration
- 5.5.11 CSM Configuration
- 5.5.12 NVMe Configuration
- 5.5.13 SATA Configuration
- 5.5.14 AMD Mem Configuration Status
- 5.6 Chipset menu
- 5.7 Security menu
- 5.8 Boot menu
- 5.9 Tool menu
- 5.10 Save & Exit menu
- 5.11 AMD CBS menu
- 5.12 Event Logs menu
- 5.13 Server Mgmt menu
- Chapter 6: Driver Installation
- Appendix
ASUS RS520A-E11-RS12U
4-3
Layout contents
Jumpers
Page
1. Clear RTC RAM (3-pin CLRTC1) 4-4
2. VGA controller setting (3-pin VGA_SW1) 4-5
3. LANNCSI setting (3-pin LANNCSI_SEL1)
4-5
4. Baseboard Management Controller setting (3-pin BMC_EN1) 4-6
5. DMLAN setting (3-pin DM_IP_SEL1) 4-6
6. IPMI SW setting (3-pin IPMI_SW1) 4-7
7. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) 4-7
8. LAN controller settings (3-pin LAN_SW1-2) 4-8
Onboard LEDs
Page
1. Standby Power LED (SBPWR1) 4-9
2. Baseboard Management Controller LED (BMCLED1) 4-9
3. Message LED (MESLED1) 4-10
4. Hard disk activity LED (HDDLED1) 4-10
Internal connectors
Page
1. Slim PCIe connector (SLIMPCIE1-10) 4-11
2. Slim SATA PCIe connector (SLMSATA_PCIE7-8) 4-11
3. USB 2.0 connector (10-1 pin USB2)
4-12
4. USB 3.2 Gen 1 connector (USB3_34)
4-12
5. Chassis Intrusion (2-pin INTRUSION1) 4-13
6. Serial port connector (10-1 pin COM1) 4-13
7. System fan connectors (6-pin FRNT_FAN1-8) 4-14
8. TPM connector (14-1 pin TPM1) 4-15
9. M.2 (NGFF) card connector (NGFF1-2) 4-15
10. Power connectors (24-pin EATXPWR; 8-pin EATX12V1; 4-pin EATX12V2) 4-16
11. VGA connector (16-pin VGA_HDR1) 4-16
12. Micro SD card slot (MSD1) 4-17
13. Hard disk activity LED connector (4-pin HDLED1) 4-17
14. System panel connector (10-1 pin SYS_PANEL1; 14-1 pin SYS_PANEL2) 4-18
15. VPP_I2C1 connector (10-1 pin VPP_I2C1) 4-19
16. BMC Debug UART connector (3-pin BMC_DEBUGUART1) 4-19
17. Smart Ride Through (SmaRT) setting (3-pin SMART_PSU1) 4-20
18. SLMPCIE SGPIO connector (6-1 pin SLM7_SGPIO1, SLM8_SGPIO1) 4-20
(continued on the next page)